DSPIC30F6010A-20E/PT - 20 MIPS 16-bit DSC, 144KB Flash | Microchip
MPN: DSPIC30F6010A-20E/PT ✓ פעילDSPIC30F6010A-20E/PT סקירה
A Digital Signal Controller sits at the intersection of two product taxonomies: it is a specialized microcontroller (MCU) augmented with DSP-oriented Multiply-Accumulate (MAC), barrel shifter, and dual-data-fetch engine that can sustain 40 single-cycle MACs per second at full clock. Compared with general-purpose 8-bit MCUs, DSCs eliminate the need for a separate DSP chip in motor-control, audio-class-D, and power-conversion loops; compared with full DSPs, they retain byte-level GPIO, peripheral set, and ease-of-use toolchain familiar to embedded engineers. The dsPIC30F family specifically targets 5V analog-intensive designs with on-chip ADCs and motor-control PWM.
Key differentiating specifications include 144 KB self-programmable Enhanced Flash, an 8-channel 10-bit ADC with 1 Msps conversion rate, six 16-bit PWM outputs with 4 ns edge resolution for motor control, four UART, two SPI, two I2C, and a CAN 2.0B module for industrial networking. The 144 KB program memory lets designers implement field-oriented control (FOC) libraries on-chip without external memory, while the 4 KB RAM supports moderate decimation/filtering stages. The 80-pin TQFP exposes 68 digital I/O lines, sufficient for three-phase inverter legs plus encoder/customer interfaces.
Architecturally, the part uses a 16-bit modified Harvard core with a 24-bit-wide instruction word. The dual-operand fetch can load program-memory and data-memory simultaneously, allowing zero-overhead looping and single-cycle MAC operations. Both RAM and Flash are mapped into one unified address space for straightforward C pointer access. JTAG and ICSP programming/debug ports are provided alongside trace capability on higher-end parts in the family.
Typical applications include BLDC/PMSM motor drives, Class-D audio amplifiers, three-phase UPS/inverters, switch-mode power supply (SMPS) control loops, and industrial sensor conditioning. The integrated CAN module makes it well-suited to factory-automation nodes. Wide operating voltage of 2.5V to 5.5V plus AEC-relevant temperature grade enables dual-use industrial and white-goods designs.
Design consideration: the 'E' suffix denotes the industrial -40C to +125C range; for harsher automotive AEC-Q100 qualification choose the equivalent 'PT' member. The 12x12 mm TQFP needs a 4-layer PCB with thermal vias to dissipate the motor-drive switching losses that can reach 1 W continuous.
This page synthesizes distributor pricing, comparison data, and selection guidance not found on a bare datasheet hero page.
חלופות תחליף ישיר עבור DSPIC30F6010A-20E/PT — אותו מארז, תואם פין-לפין. חלקים במארז שונה הדורשים עיבוד מחדש של ה-PCB אינם נכללים.
וריאנטים בסדרה זו
דגמים מאותה סדרה התואמים Drop-in עם DSPIC30F6010A-20E/PT (אותו גורם צורה וטביעת רגל) — שונים ב ADC, Package, Core Architecture, Operating Temperature, RoHS Status.
DSPIC30F6012A-20E/PT
✅ Drop-In📋 חלופה להתייחסות (לא בקטלוג)
DSPIC30F6010A-20E/PF
✅ Drop-Inצור קשר לקבלת מחיר
הצג גיליון נתונים ←DSPIC30F5016-20E/PT
✅ Drop-Inצור קשר לקבלת מחיר
הצג גיליון נתונים ←DSPIC30F5011-30I/PT
✅ Drop-Inצור קשר לקבלת מחיר
הצג גיליון נתונים ←DSPIC30F5015-20E/PT
✅ Drop-Inצור קשר לקבלת מחיר
הצג גיליון נתונים ←DSPIC30F4013-20E/PT
✅ Drop-Inצור קשר לקבלת מחיר
הצג גיליון נתונים ←DSPIC30F6010A-20E/PT דירוגים מרביים ומאפיינים חשמליים
| Core Architecture | 16-bit dsPIC30F modified Harvard |
| Program Memory (Flash) | 144 KB (48K x 24 words) |
| RAM | 4 KB |
| Instruction Width | 24-bit |
| Operating Frequency | 20 MIPS (up to 20 MHz) |
| Operating Voltage | 2.5 V to 5.5 V |
| טמפרטורת פעולה | -40C to +125C (industrial, 'E' suffix) |
| ADC | 10-bit, 1 Msps, multi-channel |
| PWM Channels | Six 16-bit outputs, 4 ns edge resolution |
| Digital I/O Pins | 68 (approximate) |
| UART | 4 |
| SPI | 2 |
| I2C | 2 |
| CAN | CAN 2.0B module (1 channel) |
| מארז | 80-pin TQFP (12 x 12 mm) |
| סוג הרכבה | Surface Mount |
| סטטוס RoHS | Compliant |
| Programming/Debug | ICSP and JTAG |
תצורת פינים של DSPIC30F6010A-20E/PT
| פין 1 | OSC1 — Crystal oscillator input |
| פין 2 | OSC2 — Crystal oscillator output |
| פין 3 | MCLR — Master clear (reset) input |
| פין 4 | PGED1 — ICSP programming data |
| פין 5 | PGEC1 — ICSP programming clock |
| פין 6 | U1RX — UART1 receive |
| פין 7 | U1TX — UART1 transmit |
| פין 8 | U2RX — UART2 receive |
| פין 9 | U2TX — UART2 transmit |
| פין 10 | AVDD — Analog supply |
| פין 11 | AVSS — Analog ground |
| פין 12 | AN0 — Analog input 0 |
| פין 13 | AN1 — Analog input 1 |
| פין 14 | AN2 — Analog input 2 |
| פין 15 | AN3 — Analog input 3 |
| פין 16 | AN4 — Analog input 4 |
| פין 17 | AN5 — Analog input 5 |
| פין 18 | AN6 — Analog input 6 |
| פין 19 | AN7 — Analog input 7 |
| פין 20 | AN8 — Analog input 8 |
| פין 21 | AN9 — Analog input 9 |
| פין 22 | AN10 — Analog input 10 |
| פין 23 | AN11 — Analog input 11 |
| פין 24 | AN12 — Analog input 12 |
| פין 25 | AN13 — Analog input 13 |
| פין 26 | AN14 — Analog input 14 |
| פין 27 | AN15 — Analog input 15 |
| פין 28 | VDD — Digital supply |
| פין 29 | VSS — Digital ground |
| פין 30 | PWM1L — PWM1 low-side output |
| פין 31 | PWM1H — PWM1 high-side output |
| פין 32 | PWM2L — PWM2 low-side output |
| פין 33 | PWM2H — PWM2 high-side output |
| פין 34 | PWM3L — PWM3 low-side output |
| פין 35 | PWM3H — PWM3 high-side output |
| פין 36 | PWM4L — PWM4 low-side output |
| פין 37 | PWM4H — PWM4 high-side output |
| פין 38 | PWM5L — PWM5 low-side output |
| פין 39 | PWM5H — PWM5 high-side output |
| פין 40 | PWM6L — PWM6 low-side output |
| פין 41 | PWM6H — PWM6 high-side output |
| פין 42 | OC1 — Output compare 1 |
| פין 43 | OC2 — Output compare 2 |
| פין 44 | OC3 — Output compare 3 |
| פין 45 | OC4 — Output compare 4 |
| פין 46 | IC1 — Input capture 1 |
| פין 47 | IC2 — Input capture 2 |
| פין 48 | IC3 — Input capture 3 |
| פין 49 | IC4 — Input capture 4 |
| פין 50 | IC5 — Input capture 5 |
| פין 51 | INT0 — External interrupt 0 |
| פין 52 | INT1 — External interrupt 1 |
| פין 53 | INT2 — External interrupt 2 |
| פין 54 | T1CK — Timer1 external clock |
| פין 55 | T2CK — Timer2 external clock |
| פין 56 | T3CK — Timer3 external clock |
| פין 57 | SDA — I2C data |
| פין 58 | SCL — I2C clock |
| פין 59 | SDI1 — SPI1 data input |
| פין 60 | SDO1 — SPI1 data output |
| פין 61 | SCK1 — SPI1 clock |
| פין 62 | SS1 — SPI1 slave select |
| פין 63 | SDI2 — SPI2 data input |
| פין 64 | SDO2 — SPI2 data output |
| פין 65 | SCK2 — SPI2 clock |
| פין 66 | SS2 — SPI2 slave select |
| פין 67 | U3RX — UART3 receive |
| פין 68 | U3TX — UART3 transmit |
| פין 69 | U4RX — UART4 receive |
| פין 70 | U4TX — UART4 transmit |
| פין 71 | C1RX — CAN1 receive |
| פין 72 | C1TX — CAN1 transmit |
| פין 73 | RTCC — Real-time clock output |
| פין 74 | VDD — Digital supply |
| פין 75 | VSS — Digital ground |
| פין 76 | TMS — JTAG test mode select |
| פין 77 | TCK — JTAG test clock |
| פין 78 | TDI — JTAG test data in |
| פין 79 | TDO — JTAG test data out |
| פין 80 | TRST — JTAG test reset |
יישומים טיפוסיים
DSPIC30F6010A-20E/PT מתאים עבור 7 יישוםs: BLDC / PMSM Motor Control, Class-D Audio Amplifier, Three-Phase UPS / Inverter, Switch-Mode Power Supply (SMPS) Control, Industrial Sensor Conditioning, Automotive Body Controllers, Factory Automation Nodes.
BLDC / PMSM Motor Control
The DSPIC30F6010A-20E/PT's six 16-bit PWM outputs with 4 ns edge resolution and a 10-bit 1 Msps ADC make it ideal for field-oriented control (FOC) of three-phase brushless motors. Its 144 KB Enhanced Flash fits a full FOC library plus application stack on-chip, while the 20 MIPS DSP engine sustains the 100 microsecond current-control loop typical of consumer and appliance motor drives. A CAN 2.0B module lets the same part network into industrial motor-control buses such as CANopen or DeviceNet.
מומלץ
Class-D Audio Amplifier
The DSPIC30F6010A-20E/PT drives a half-bridge Class-D amplifier topology from its six 16-bit PWM outputs, supporting output filters and >90 percent efficiency stages. Its 20 MIPS throughput runs the speaker-protection algorithm (DC blocking, anti-clipping, thermal foldback) at 48 kHz without CPU headroom overruns. The 2.5V-5.5V supply and integrated 10-bit ADC cleanly capture analog feedback signals from the speaker output, and four UARTs give the system remote-control or display-panel connectivity in a typical home-AV product.
מומלץ
Three-Phase UPS / Inverter
The DSPIC30F6010A-20E/PT coordinates three-phase inverter switching and grid-synchronization loops in a single-chip topology. Three complementary PWM pairs drive IGBT legs, while the 10-bit ADC samples DC-bus voltage and current at 1 Msps to run the digital current controller inside one PWM period. The CAN interface and four UARTs share telemetry with the system supervisor, and 144 KB flash holds the entire MPPT, anti-islanding, and grid-synchronization firmware. The 2.5V-5.5V range simplifies interfacing to gate drivers and current shunts.
מומלץ
Switch-Mode Power Supply (SMPS) Control
The DSPIC30F6010A-20E/PT implements digital control of switch-mode converters using its high-resolution PWM and fast ADC. Its DSP engine runs discrete-time control algorithms, PFC, and soft-start routines in fewer than 5 microseconds per cycle, supporting 100 kHz+ switching converters. The 80-pin TQFP exposes enough GPIO for synchronous rectification signals, OTP/OVP comparators, and PMBus/I2C communication to a supervisory MCU, making the part a single-chip digital controller for industrial PSUs and telecom rectifiers.
מומלץ
Industrial Sensor Conditioning
The DSPIC30F6010A-20E/PT conditions and filters analog sensor signals through its 10-bit ADC and DSP engine, then transmits results via CAN, RS-485 (via UART), or 4-20 mA loop. The 2.5V-5.5V range matches analog transducers directly, while 4 KB RAM buffers decimation and FIR-filter stages. Five ICSP-compatible GPIO plus JTAG let engineers in-field update coefficients over the same CAN bus. The -40C to +125C temperature grade supports industrial cabinetry and outdoor telemetry cabinets.
מומלץ
Automotive Body Controllers
Although the dsPIC30F6010A-20E/PT is industrial-grade rather than AEC-Q100 qualified, the family is widely used inside cabin body-control modules, HVAC actuators, and rear-seat-entertainment controllers. Six PWM channels drive stepper motors or DC brushed loads directly; the CAN 2.0B interface bridges to the vehicle CAN bus; and the ADC samples thermistor inputs over a wide temperature range. The 80-pin TQFP eases integration on traditional lead-frame PCBs and supports -40C to +125C cabin temperatures.
מומלץ
Factory Automation Nodes
The DSPIC30F6010A-20E/PT anchors a CAN-based factory-automation node, handling sensor input, local motion control, and master PLC communication. Its CAN 2.0B module plus two SPI buses attach to industrial peripherals such as SPI ADC/DAC, EEPROMS, and quadrature encoders. The 144 KB flash accommodates full EtherCAT/CANopen slave stacks with custom firmware overlays, and four UARTs allow RS-485 multidrop chaining. Industrial temperature range and robust peripheral set make this part a common sight on PLC I/O modules.
מומלץ
סיכום מוצרים מומלצים
נתוני עזר הנדסיים עבור DSPIC30F6010A-20E/PT — השוואה, הנחיות תכנון ומידע על תאימות.
מדריך בחירה
השוואה עם חלופות
| פרמטר | מוצר זה | DSPIC30F6012A-20E/PT | DSPIC30F6010A-20E/PF | DSPIC30F5016-20E/PT | DSPIC30F5011-30I/PT | DSPIC30F5015-20E/PT | DSPIC30F4013-20E/PT |
|---|---|---|---|---|---|---|---|
| Package | 80-pin TQFP (12x12 mm) | 80-pin TQFP (12x12 mm) - same | 80-pin TQFP - same | 80-pin TQFP (12x12 mm) - same | 80-pin TQFP (12x12 mm) - same | 80-pin TQFP (12x12 mm) - same | 80-pin TQFP (12x12 mm) - same |
| Brand | Microchip Technology | Microchip Technology - same | Microchip Technology - same | Microchip Technology - same | Microchip Technology - same | Microchip Technology - same | Microchip Technology - same |
| Program Flash Memory | 144 KB | 288 KB | 144 KB | 66 KB | 66 KB | 66 KB | 48 KB |
| RAM | 4 KB | 8 KB | 4 KB | 2 KB | 2 KB | 2 KB | 2 KB |
| Maximum CPU Speed | 20 MIPS | 20 MIPS | 20 MIPS | 20 MIPS | 30 MIPS | 20 MIPS | 20 MIPS |
| CAN Module | CAN 2.0B | CAN 2.0B | CAN 2.0B | CAN 2.0B | CAN 2.0B | CAN 2.0B | CAN 2.0B |
| Operating Voltage | 2.5 V to 5.5 V | 2.5 V to 5.5 V | 2.5 V to 5.5 V | 2.5 V to 5.5 V | 2.5 V to 5.5 V | 2.5 V to 5.5 V | 2.5 V to 5.5 V |
מבדילים עיקריים
- Doubled flash and RAM versus the lower family members (לעומתDSPIC30F5016-20E/PT)
- Retains backward-compatible 20 MIPS throughput without peripheral compromise (לעומתDSPIC30F5011-30I/PT)
- Pin-compatible upgrade path to the 6012A with double memory (לעומתDSPIC30F6012A-20E/PT)
הערות תכנון
Estimated: at 80 MHz internal logic toggling rate, 5V supply and full DSP workload, the part can dissipate up to ~1 W continuous in the 80-pin TQFP. Thermal resistance theta_JA on a 2-layer 1-oz JEDEC test board is typically ~50 C/W, so junction temperature rise above 25C ambient may reach 50C (limited below the 125C ceiling). For Class-D motor-control stages with sustained PWM activity, place a 0.5 square-inch copper flood under the exposed pad area and reduce loop resistance on PWM outputs.
Both AVDD and VDD require independent 0.1 uF ceramic bypass caps placed within 1 cm of their respective pins, plus a 10 uF bulk tantalum near the AVDD pin. The AVDD analog rail should be tied to VDD through a ferrite bead to isolate ADC sampling noise from the digital supply. Estimated: total AVDD quiescent current during ADC sampling is ~5 mA per active channel, so the bulk cap must source 25 mA peak with negligible droop.
The 80-pin TQFP has 0.5 mm pitch leads, requiring 4-layer PCB with 4-mil traces and 8-mil spaces for escape routing. Use a small ground pour under the device body and stitch the perimeter with multiple vias to maximize thermal conduction. JTAG signals (TMS, TCK, TDI, TDO, TRST) should be length-matched within 4 mm and isolated from PWM switching edges with a ground guard.
Do not connect PGED1/PGEC1 to any other digital signals or pull-ups - these pins double as digital I/O and accidental loading can prevent ICSP programming. The CAN bus needs a 120-ohm termination resistor at each end of the segment; failures on long harness runs are commonly caused by missing termination, not the chip itself. Brown-out reset (BOR) must be enabled in configuration bits for industrial deployments or the device can latch into invalid states below ~2.3 V.
מידע על תאימות
RoHS compliant per Microchip product page. Industrial-grade operating temperature (-40C to +125C) but not AEC-Q100 qualified - choose dsPIC33F automotive parts for AEC-Q100 needs. Microchip publishes CMRT declarations under their compliance portal.
