LM2903WDT - Dual Open-Collector Comparator | STMicroelectronics
MPN: LM2903WDT ✓ פעילLM2903WDT סקירה
A voltage comparator is an analog integrated circuit that compares one input voltage with another and changes its output state when the differential input crosses a switching threshold. The LM2903 belongs to the comparator hierarchy, where a comparator IC sits between basic analog signal-conditioning circuits and higher-level control systems. Each channel can compare an external signal against a reference voltage, allowing a logic-compatible indication of whether the signal is above or below the selected threshold.
The LM2903WDT provides two comparator channels in one 8-pin SOIC package. Its open-collector outputs can sink current from a pulled-up supply while placing the output in a high-impedance state when inactive. This arrangement supports wired logic, relay-driver interfaces, and systems that require multiple open-collector outputs sharing a bus. The low 0.4 mA supply current is valuable in battery-powered or continuously monitored equipment where comparator power consumption contributes directly to standby energy use.
The stated 250 mV input offset voltage and 25 nA input offset current define the practical accuracy limits around the switching point. Input offset voltage is the difference between the two inputs required to move the output through its switching region, while input offset current represents the residual current entering the input terminals. These values should be considered when the application requires a precise switching threshold rather than general threshold detection.
Typical uses include battery monitoring, sensor-limit detection, industrial control interfaces, window or level comparators, and low-power monitoring subsystems. The comparator can operate directly from a low-voltage supply and accept signals extending across the supply range, reducing the need for separate input attenuation when the monitored voltage remains within safe absolute limits. The two channels may be used independently or together for window comparison, provided their input and output arrangements satisfy the application requirements.
Designers should account for open-collector output behavior by adding an appropriate pull-up resistor and verifying the pull-up voltage against the connected logic. Input pins must remain within the device's permitted common-mode and absolute-maximum limits. Because the offset characteristics contribute uncertainty at the threshold, applications requiring tighter accuracy should add input attenuation, filtering, or external precision references. This page combines the confirmed ordering information with drop-in alternatives, comparison guidance, and practical circuit-design considerations.
חלופות תחליף ישיר עבור LM2903WDT — אותו מארז, תואם פין-לפין. חלקים במארז שונה הדורשים עיבוד מחדש של ה-PCB אינם נכללים.
וריאנטים בסדרה זו
דגמים מאותה סדרה התואמים Drop-in עם LM2903WDT (אותו גורם צורה וטביעת רגל) — שונים ב Package, Output Type, Input Offset Voltage, Input Bias Current, Number of Channels.
LM293D
✅ Drop-Inצור קשר לקבלת מחיר
הצג גיליון נתונים ←LM393DT
✅ Drop-In✓ במלאי
$0.0461 / יחידה
הצג גיליון נתונים ←LM2903WDT
✅ Drop-Inצור קשר לקבלת מחיר
הצג גיליון נתונים ←LM2903BIDR
✅ Drop-Inצור קשר לקבלת מחיר
הצג גיליון נתונים ←LMV393
✅ Drop-In📋 חלופה להתייחסות (לא בקטלוג)
LM2903WDT דירוגים מרביים ומאפיינים חשמליים
| Product Type | Dual differential voltage comparator |
| Comparator Channel Count | 2 channels |
| סוג פלט | Open-collector |
| Input Type | Differential |
| Common-Mode Input Capability | Rail-to-rail |
| זרם אספקה | 0.4 mA |
| Input Offset Current | 25 nA |
| Input Offset Voltage | 250 mV |
| מארז | 8-pin SOIC |
| מספר פינים | 8 pins |
| סוג הרכבה | Surface mount |
| AEC-Q100 Qualification | Qualified and characterized according to AEC Q100 |
מדריך תצורת פינים של LM2903WDT 8-pin soic
תצורת פינים עבור LM2903WDT (מארזת 8-pin soic). רכיב אנלוגי זה כולל פיני כניסה, יציאה ואספקת מתח. יש לעיין בגיליון הנתונים של היצרן לתצורות פיני איפוס היסט, פיצוי והפעלה. אידיאלי למעגלי עיצוב אותות ומגברים.
אין נתוני פריסת פינים מפורטים עבור LM2903WDT.
עיינו ב- גיליון נתונים עבור תצורת פינים מלאה.
יישומים טיפוסיים
LM2903WDT מתאים עבור 6 יישוםs: Battery Voltage Monitoring, Industrial Sensor Limit Detection, Power Supply Overvoltage Detection, Motor and Solenoid Control, Battery-Powered IoT Sensing, Window Comparator Systems.
Battery Voltage Monitoring
The LM2903WDT suits low-power battery threshold detection because its two channels can monitor charge and discharge limits while the device consumes a typical 0.4 mA. One channel can compare the battery voltage with an upper reference and the other with a lower reference, producing separate open-collector alerts. The rail-to-rail input capability is useful when the monitored signal approaches the operating supply, although the 250 mV input offset must be included in the threshold-error budget. For higher-precision battery management, use a windowing circuit, input scaling, or a more accurate reference rather than assuming the comparator threshold is exact.
מומלץ
Industrial Sensor Limit Detection
The LM2903WDT can convert a conditioned industrial sensor signal into a digital limit event without adding substantial standby load. Its two differential channels support separate high- and low-limit checks, while the open-collector outputs can drive an isolated relay, optocoupler input, or PLC interface through a pull-up network. The 25 nA input offset current is favorable for high-impedance sensor nodes, while the 250 mV input offset voltage sets the basic accuracy of a direct threshold comparison. Industrial designs should also verify the supported input common-mode range, supply limits, and noise margin at the actual field voltage.
מומלץ
Power Supply Overvoltage Detection
The LM2903WDT can monitor a divided power rail and assert an open-collector fault signal when the voltage crosses a defined limit. With two channels, a single device can supervise both upper and lower boundaries, reducing component count in a power-supply controller. Its rail-to-rail input characteristic supports detection near the supply range, and the typical 0.4 mA supply current adds little overhead to continuously monitored systems. Because the comparator does not regulate the rail, its 250 mV offset translates into a scaled threshold uncertainty that must be included in the power system's fault-margin calculation.
מומלץ
Motor and Solenoid Control
The LM2903WDT is suitable for detecting motor-current or actuator-supply thresholds before driving a discrete power stage. Its differential inputs allow a scaled current-sense signal to be compared with a reference, and the open-collector output can enable a gate driver, relay, or protection latch. The typical 0.4 mA supply current is useful where continuous monitoring matters, while two channels can support independent current and temperature limits. Designers must ensure the comparator remains inside its common-mode range throughout startup, and must account for the 250 mV offset when setting motor-current trip points.
מומלץ
Battery-Powered IoT Sensing
The LM2903WDT fits battery-powered IoT sensing when a wake-up node must be evaluated without continuously powering a higher-power measurement chain. The device's typical 0.4 mA supply current and two comparator channels allow a compact node to compare a sensor output against a threshold and control a downstream power rail. Open-collector outputs can be pulled up to a low-energy logic voltage or used to enable a load switch. The 25 nA input offset current is particularly useful with high-impedance sensors, although the 250 mV offset voltage should be checked against the minimum sensor signal that must trigger an event.
מומלץ
Window Comparator Systems
The LM2903WDT naturally supports window comparison by assigning its two channels to lower and upper thresholds. The resulting open-collector outputs can identify whether a monitored voltage is below the lower limit, inside the permitted range, or above the upper limit. This arrangement is useful for power rails, signal sources, temperature probes, and charging systems. Both channels share an 8-pin SOIC package, reducing board area, and the typical 0.4 mA supply current supports low-power operation. To obtain dependable limits, include the 250 mV offset of each channel in the worst-case threshold calculation and allow for offset drift across temperature.
מומלץ
סיכום מוצרים מומלצים
נתוני עזר הנדסיים עבור LM2903WDT — השוואה, הנחיות תכנון ומידע על תאימות.
מדריך בחירה
השוואה עם חלופות
| פרמטר | מוצר זה | LM293D | LM393DT | LM2903WDT | LM2903 | LMV393 |
|---|---|---|---|---|---|---|
| Brand | STMicroelectronics | STMicroelectronics | STMicroelectronics | ROHM Semiconductor | Texas Instruments | Texas Instruments |
| Package | 8-pin SOIC | 8-pin SOIC | 8-pin SOIC | 8-pin SOIC | 8-pin SOIC | 8-pin SOIC |
| Comparator Channels | 2 channels | 2 channels | 2 channels | 2 channels | 2 channels | 2 channels |
| Output Type | Open-collector | Open-collector | Open-collector | Open-collector | Open-collector | Open-collector |
| Input Configuration | Dual differential | Dual differential | Dual differential | Dual differential | Dual differential | Dual differential |
מבדילים עיקריים
- Two-channel integration in an 8-pin SOIC package (לעומתLMV393)
- Low confirmed supply current (לעומתLM2903)
- Defined input-offset characteristics (לעומתLM293D)
- Open-collector output in a common 8-pin footprint (לעומתLM393DT)
הערות תכנון
Do not treat an open-collector output as a push-pull logic output. Each channel requires an external pull-up resistor to establish its inactive high level. Size the resistor from the permitted output sink current, desired rise time, pull-up voltage, and continuous power dissipation. Also check that the downstream logic recognizes the resulting high voltage and that only the intended comparator channel can pull the shared bus low.
Estimated: using the confirmed typical supply current of 0.4 mA and a 5 V supply, the LM2903WDT supply power is 0.4 mA multiplied by 5 V, or 2.0 mW. The estimate excludes comparator output pull-up current, input bias effects, and dynamic transients. Use it as a comparator-only baseline and add the pull-up network's switching and leakage loads when calculating total standby power.
Include the 250 mV input offset voltage when defining switch-on and switch-off thresholds, and use the datasheet limit rather than only the typical value when error margins matter. Differential input noise can also move the switching point. For precision applications, add hysteresis, filter excessive input noise, or use a precision reference and an amplifier with gain ahead of the comparator.
Place the pull-up resistor close to the open-collector output so that the trace has minimum capacitance and sensitivity to induced noise. Keep comparator input traces short, route them away from switching nodes, and use a quiet ground return. If both channels monitor slow, high-impedance signals, consider guarding or guarding techniques around the input nodes to reduce leakage-induced offset.
מידע על תאימות
The manufacturer datasheet states that the LM2903 family is qualified and characterized according to AEC Q100 and Q003, or equivalent. RoHS, REACH, lead-free, halogen-free, and conflict-minerals status require confirmation from the current manufacturer product documentation.