LM2903WDT - Dual Open-Collector Comparator | STMicroelectronics
MPN: LM2903WDT ✓ Hoạt độngLM2903WDT Tóm tắt
A voltage comparator is an analog integrated circuit that compares one input voltage with another and changes its output state when the differential input crosses a switching threshold. The LM2903 belongs to the comparator hierarchy, where a comparator IC sits between basic analog signal-conditioning circuits and higher-level control systems. Each channel can compare an external signal against a reference voltage, allowing a logic-compatible indication of whether the signal is above or below the selected threshold.
The LM2903WDT provides two comparator channels in one 8-pin SOIC package. Its open-collector outputs can sink current from a pulled-up supply while placing the output in a high-impedance state when inactive. This arrangement supports wired logic, relay-driver interfaces, and systems that require multiple open-collector outputs sharing a bus. The low 0.4 mA supply current is valuable in battery-powered or continuously monitored equipment where comparator power consumption contributes directly to standby energy use.
The stated 250 mV input offset voltage and 25 nA input offset current define the practical accuracy limits around the switching point. Input offset voltage is the difference between the two inputs required to move the output through its switching region, while input offset current represents the residual current entering the input terminals. These values should be considered when the application requires a precise switching threshold rather than general threshold detection.
Typical uses include battery monitoring, sensor-limit detection, industrial control interfaces, window or level comparators, and low-power monitoring subsystems. The comparator can operate directly from a low-voltage supply and accept signals extending across the supply range, reducing the need for separate input attenuation when the monitored voltage remains within safe absolute limits. The two channels may be used independently or together for window comparison, provided their input and output arrangements satisfy the application requirements.
Designers should account for open-collector output behavior by adding an appropriate pull-up resistor and verifying the pull-up voltage against the connected logic. Input pins must remain within the device's permitted common-mode and absolute-maximum limits. Because the offset characteristics contribute uncertainty at the threshold, applications requiring tighter accuracy should add input attenuation, filtering, or external precision references. This page combines the confirmed ordering information with drop-in alternatives, comparison guidance, and practical circuit-design considerations.
Bộ thay thế dễ dàng lắp đặt cho LM2903WDT — cùng gói, chân-to-chân tương thích. Các bộ phận yêu cầu hàn PCB bị loại trừ.
Các biến thể trong loạt này
Các mẫu cùng loạt có thể lắp đặt dễ dàng tương thích với LM2903WDT (cùng hình factor và footprint) — khác nhau ở Package, Output Type, Input Offset Voltage, Input Bias Current, Number of Channels.
LM293D
✅ Drop-InLiên hệ để biết giá
Xem tài liệu →LM393DT
✅ Drop-In✓ Còn hàng
$0.0461 / Đơn vị
Xem tài liệu →LM2903WDT
✅ Drop-InLiên hệ để biết giá
Xem tài liệu →LM2903BIDR
✅ Drop-InLiên hệ để biết giá
Xem tài liệu →LMV393
✅ Drop-In📋 Tham chiếu thay thế (không có trong danh mục)
LM2903WDT Tỷ lệ tối đa & tính chất điện
| Product Type | Dual differential voltage comparator |
| Comparator Channel Count | 2 channels |
| Kiểu đầu ra | Open-collector |
| Input Type | Differential |
| Common-Mode Input Capability | Rail-to-rail |
| Điện áp cung cấp | 0.4 mA |
| Input Offset Current | 25 nA |
| Input Offset Voltage | 250 mV |
| Hộp | 8-pin SOIC |
| Số chân | 8 pins |
| Kiểu lắp đặt | Surface mount |
| AEC-Q100 Qualification | Qualified and characterized according to AEC Q100 |
Hướng dẫn cấu hình chân LM2903WDT 8-pin soic
Cấu hình chân cho LM2903WDT (8-pin soic gói). Thành phần số hiệu này có chân đầu vào, đầu ra và nguồn cung cấp. Tham khảo tài liệu thông số kỹ thuật của nhà sản xuất để biết cấu hình chân bù, bù trừ và chân kích hoạt. Hoàn hảo cho điều kiện tín hiệu và mạch khuếch đại.
Không có dữ liệu chân cụ thể sẵn có cho LM2903WDT.
Tham khảo: tài liệu kỹ thuật cho cấu hình chân đầy đủ.
Ứng dụng tiêu biểu
LM2903WDT phù hợp cho 6 Áp dụngs: Battery Voltage Monitoring, Industrial Sensor Limit Detection, Power Supply Overvoltage Detection, Motor and Solenoid Control, Battery-Powered IoT Sensing, Window Comparator Systems.
Battery Voltage Monitoring
The LM2903WDT suits low-power battery threshold detection because its two channels can monitor charge and discharge limits while the device consumes a typical 0.4 mA. One channel can compare the battery voltage with an upper reference and the other with a lower reference, producing separate open-collector alerts. The rail-to-rail input capability is useful when the monitored signal approaches the operating supply, although the 250 mV input offset must be included in the threshold-error budget. For higher-precision battery management, use a windowing circuit, input scaling, or a more accurate reference rather than assuming the comparator threshold is exact.
Được đề xuất
Industrial Sensor Limit Detection
The LM2903WDT can convert a conditioned industrial sensor signal into a digital limit event without adding substantial standby load. Its two differential channels support separate high- and low-limit checks, while the open-collector outputs can drive an isolated relay, optocoupler input, or PLC interface through a pull-up network. The 25 nA input offset current is favorable for high-impedance sensor nodes, while the 250 mV input offset voltage sets the basic accuracy of a direct threshold comparison. Industrial designs should also verify the supported input common-mode range, supply limits, and noise margin at the actual field voltage.
Được đề xuất
Power Supply Overvoltage Detection
The LM2903WDT can monitor a divided power rail and assert an open-collector fault signal when the voltage crosses a defined limit. With two channels, a single device can supervise both upper and lower boundaries, reducing component count in a power-supply controller. Its rail-to-rail input characteristic supports detection near the supply range, and the typical 0.4 mA supply current adds little overhead to continuously monitored systems. Because the comparator does not regulate the rail, its 250 mV offset translates into a scaled threshold uncertainty that must be included in the power system's fault-margin calculation.
Được đề xuất
Motor and Solenoid Control
The LM2903WDT is suitable for detecting motor-current or actuator-supply thresholds before driving a discrete power stage. Its differential inputs allow a scaled current-sense signal to be compared with a reference, and the open-collector output can enable a gate driver, relay, or protection latch. The typical 0.4 mA supply current is useful where continuous monitoring matters, while two channels can support independent current and temperature limits. Designers must ensure the comparator remains inside its common-mode range throughout startup, and must account for the 250 mV offset when setting motor-current trip points.
Được đề xuất
Battery-Powered IoT Sensing
The LM2903WDT fits battery-powered IoT sensing when a wake-up node must be evaluated without continuously powering a higher-power measurement chain. The device's typical 0.4 mA supply current and two comparator channels allow a compact node to compare a sensor output against a threshold and control a downstream power rail. Open-collector outputs can be pulled up to a low-energy logic voltage or used to enable a load switch. The 25 nA input offset current is particularly useful with high-impedance sensors, although the 250 mV offset voltage should be checked against the minimum sensor signal that must trigger an event.
Được đề xuất
Window Comparator Systems
The LM2903WDT naturally supports window comparison by assigning its two channels to lower and upper thresholds. The resulting open-collector outputs can identify whether a monitored voltage is below the lower limit, inside the permitted range, or above the upper limit. This arrangement is useful for power rails, signal sources, temperature probes, and charging systems. Both channels share an 8-pin SOIC package, reducing board area, and the typical 0.4 mA supply current supports low-power operation. To obtain dependable limits, include the 250 mV offset of each channel in the worst-case threshold calculation and allow for offset drift across temperature.
Được đề xuất
Tóm tắt các sản phẩm được đề xuất
Dữ liệu tham khảo kỹ thuật cho LM2903WDT — so sánh, hướng dẫn thiết kế và thông tin tuân thủ.
Hướng dẫn chọn lựa
So sánh với các sản phẩm thay thế
| Tham số | Sản phẩm này | LM293D | LM393DT | LM2903WDT | LM2903 | LMV393 |
|---|---|---|---|---|---|---|
| Brand | STMicroelectronics | STMicroelectronics | STMicroelectronics | ROHM Semiconductor | Texas Instruments | Texas Instruments |
| Package | 8-pin SOIC | 8-pin SOIC | 8-pin SOIC | 8-pin SOIC | 8-pin SOIC | 8-pin SOIC |
| Comparator Channels | 2 channels | 2 channels | 2 channels | 2 channels | 2 channels | 2 channels |
| Output Type | Open-collector | Open-collector | Open-collector | Open-collector | Open-collector | Open-collector |
| Input Configuration | Dual differential | Dual differential | Dual differential | Dual differential | Dual differential | Dual differential |
Bảo phân biệt quan trọng
- Two-channel integration in an 8-pin SOIC package (vsLMV393)
- Low confirmed supply current (vsLM2903)
- Defined input-offset characteristics (vsLM293D)
- Open-collector output in a common 8-pin footprint (vsLM393DT)
Ghi chú thiết kế
Do not treat an open-collector output as a push-pull logic output. Each channel requires an external pull-up resistor to establish its inactive high level. Size the resistor from the permitted output sink current, desired rise time, pull-up voltage, and continuous power dissipation. Also check that the downstream logic recognizes the resulting high voltage and that only the intended comparator channel can pull the shared bus low.
Estimated: using the confirmed typical supply current of 0.4 mA and a 5 V supply, the LM2903WDT supply power is 0.4 mA multiplied by 5 V, or 2.0 mW. The estimate excludes comparator output pull-up current, input bias effects, and dynamic transients. Use it as a comparator-only baseline and add the pull-up network's switching and leakage loads when calculating total standby power.
Include the 250 mV input offset voltage when defining switch-on and switch-off thresholds, and use the datasheet limit rather than only the typical value when error margins matter. Differential input noise can also move the switching point. For precision applications, add hysteresis, filter excessive input noise, or use a precision reference and an amplifier with gain ahead of the comparator.
Place the pull-up resistor close to the open-collector output so that the trace has minimum capacitance and sensitivity to induced noise. Keep comparator input traces short, route them away from switching nodes, and use a quiet ground return. If both channels monitor slow, high-impedance signals, consider guarding or guarding techniques around the input nodes to reduce leakage-induced offset.
Thông tin tuân thủ
The manufacturer datasheet states that the LM2903 family is qualified and characterized according to AEC Q100 and Q003, or equivalent. RoHS, REACH, lead-free, halogen-free, and conflict-minerals status require confirmation from the current manufacturer product documentation.