LTC2256CUJ-12 - 12-Bit 25Msps Ultralow Power 1.8V ADC | Analog Devices
MPN: LTC2256CUJ-12 ✓ פעילLTC2256CUJ-12 סקירה
What is an SAR/pipelined ADC? An analog-to-digital converter (ADC) translates continuous analog signals into discrete digital codes. The pipelined ADC architecture, used in the LTC2256CUJ-12, combines multiple low-resolution flash stages with digital error correction to deliver high sampling rates (tens to hundreds of MSPS) at moderate resolution (10-16 bit), suiting it to wideband communications, imaging, and instrumentation. Within the broader semiconductor hierarchy, the LTC2256CUJ-12 belongs to the data-converter family (ADC), which sits under mixed-signal ICs and interface ICs.
Key specifications include 0.17 ps RMS ultralow jitter for accurate IF undersampling, ±0.3 LSB INL (typical) and ±0.1 LSB DNL (typical) with no missing codes over temperature, and 0.3 LSB RMS transition noise. The digital outputs can be configured as full-rate CMOS, double-data-rate CMOS, or double-data-rate LVDS, with a separate output supply pin allowing the CMOS swing to range from 0.5 V to 1.8 V. The 1.8 V single-supply operation makes it well-suited to low-power, battery-friendly designs.
The architecture combines a front-end differential S/H, a multi-stage pipelined quantizer chain, and an internal bandgap reference, while supporting an optional external reference for noise-critical paths. AC performance - 71.1 dB SNR and 88 dB SFDR at 25 Msps - is preserved across input frequencies up to and beyond Nyquist, with sub-picosecond aperture jitter enabling accurate undersampling of IF signals commonly used in communications and radar systems.
Typical applications include cellular base-station receivers, IF digitizers in software-defined radio (SDR), medical imaging front-ends, handheld portable test equipment, and low-power instrumentation. The combination of 1.8 V single-supply operation, 25 Msps speed, and differential input makes it ideal for any signal chain where wide dynamic range and low power must coexist.
When designing in this part, use a multilayer PCB with a continuous unbroken ground plane and place the exposed pad on a thermal/ground copper pour. Decouple AVDD, DVDD, and OVDD with 10 uF and 0.1 uF ceramic capacitors placed as close to the pins as possible, and route differential analog inputs with matched impedance and length to preserve the rated SFDR. A separate OVDD supply lets you interface directly to 1.8 V logic without level shifters.
This page consolidates distributor stock, verified pin-compatible alternatives, and application guidance that goes beyond the manufacturer's datasheet so procurement and design engineers can decide quickly whether the LTC2256CUJ-12 fits their signal chain.
חלופות תחליף ישיר עבור LTC2256CUJ-12 — אותו מארז, תואם פין-לפין. חלקים במארז שונה הדורשים עיבוד מחדש של ה-PCB אינם נכללים.
וריאנטים בסדרה זו
דגמים מאותה סדרה התואמים Drop-in עם LTC2256CUJ-12 (אותו גורם צורה וטביעת רגל) — שונים ב Package, RoHS Status, Resolution, Transition Noise, Data Interface.
LTC2256IUJ-12#PBF
✅ Drop-In📋 חלופה להתייחסות (לא בקטלוג)
LTC2257CUJ-12#PBF
✅ Drop-In📋 חלופה להתייחסות (לא בקטלוג)
LTC2258CUJ-12#PBF
✅ Drop-In📋 חלופה להתייחסות (לא בקטלוג)
LTC2256CUJ-12#TRPBF
✅ Drop-In📋 חלופה להתייחסות (לא בקטלוג)
LTC2260CUJ-12#PBF
✅ Drop-In📋 חלופה להתייחסות (לא בקטלוג)
LTC2151CUJ-14#PBF
✅ Drop-In📋 חלופה להתייחסות (לא בקטלוג)
LTC2256CUJ-12 דירוגים מרביים ומאפיינים חשמליים
| רזולוציה | 12 bit |
| Sample Rate | 25 Msps |
| Architecture | Pipelined |
| Number of Channels | 1 |
| Input Type | Differential |
| Data Interface | Parallel CMOS / DDR CMOS / DDR LVDS |
| Analog Supply Voltage (AVDD) | 1.8 V (typ) |
| Power Consumption | 62 mW at 25 Msps |
| SNR | 71.1 dB |
| SFDR | 88 dB |
| INL (typical) | ±0.3 LSB |
| DNL (typical) | ±0.1 LSB |
| Transition Noise | 0.3 LSB RMS |
| Aperture Jitter | 0.17 ps RMS |
| Output Supply Range (OVDD) | 0.5 V to 1.8 V |
| Reference | Internal or external |
| מארז | 40-QFN (6 x 6 mm) with exposed pad |
| Operating Temperature (Commercial, CUJ) | 0 C to +70 C |
| סטטוס RoHS | Compliant (#PBF suffix) |
| Lead-Free | Yes (#PBF suffix) |
תצורת פינים של LTC2256CUJ-12
| פין 1 | AIN+ — Differential analog input positive |
| פין 2 | AIN- — Differential analog input negative |
| פין 3 | VCM — Common-mode voltage output |
| פין 4 | REFT — Reference top decoupling |
| פין 5 | REFB — Reference bottom decoupling |
| פין 6 | REFRTN — Reference return |
| פין 7 | REFIN — Reference input / internal reference output |
| פין 8 | SENSE — Reference mode select (internal/external) |
| פין 9 | OGND — Output driver ground |
| פין 10 | OVDD — Output driver supply |
| פין 11 | D0 — Digital output bit 0 (LSB) |
| פין 12 | D1 — Digital output bit 1 |
| פין 13 | D2 — Digital output bit 2 |
| פין 14 | D3 — Digital output bit 3 |
| פין 15 | D4 — Digital output bit 4 |
| פין 16 | D5 — Digital output bit 5 |
| פין 17 | D6 — Digital output bit 6 |
| פין 18 | D7 — Digital output bit 7 |
| פין 19 | D8 — Digital output bit 8 |
| פין 20 | D9 — Digital output bit 9 |
| פין 21 | D10 — Digital output bit 10 |
| פין 22 | D11 — Digital output bit 11 (MSB) |
| פין 23 | NC — Not connected (per datasheet) |
| פין 24 | OGND — Output driver ground |
| פין 25 | OVDD — Output driver supply |
| פין 26 | CLKOUT- — Differential clock output negative |
| פין 27 | CLKOUT+ — Differential clock output positive |
| פין 28 | CLK- — Differential clock input negative |
| פין 29 | CLK+ — Differential clock input positive |
| פין 30 | MODE — Output mode select (CMOS / DDR CMOS / DDR LVDS) |
| פין 31 | OE — Output enable |
| פין 32 | DGND — Digital ground |
| פין 33 | DVDD — Digital 1.8 V supply |
| פין 34 | AGND — Analog ground |
| פין 35 | AVDD — Analog 1.8 V supply |
| פין 36 | NC — Not connected (per datasheet) |
| פין 37 | NC — Not connected (per datasheet) |
| פין 38 | NC — Not connected (per datasheet) |
| פין 39 | NC — Not connected (per datasheet) |
| פין 40 | EP — Exposed pad - thermal/ground connection |
יישומים טיפוסיים
LTC2256CUJ-12 מתאים עבור 6 יישוםs: Cellular Base-Station IF Digitizer, Software-Defined Radio (SDR) Receiver, Medical Imaging Front-End, Handheld Portable Test Equipment, Low-Power Industrial Instrumentation, Wideband Communication Signal Analyzer.
Cellular Base-Station IF Digitizer
The LTC2256CUJ-12 fits cellular base-station IF digitizers because its 25 Msps sample rate and 0.17 ps RMS aperture jitter let it undersample IF signals cleanly without aliasing artifacts. Its 71.1 dB SNR and 88 dB SFDR preserve signal integrity across multi-carrier GSM, LTE, and 5G NR waveforms, while 1.8 V single-supply operation reduces board-level power budget. Placed between the SAW filter and the FPGA baseband, the ADC drives parallel CMOS or DDR LVDS outputs directly to the FPGA SERDES, eliminating level shifters and shrinking BOM. The 40-QFN exposed pad provides a low-thermal-resistance path so the 62 mW dissipation is handled with a standard ground pour.
מומלץ
Software-Defined Radio (SDR) Receiver
In software-defined radio receivers, the LTC2256CUJ-12 digitizes wideband IF blocks directly into the FPGA, where DSP performs channelization and demodulation. Its 0.17 ps RMS aperture jitter is below the phase-noise contribution of typical VCOs, so the SNR floor of 71.1 dB is dominated by the input signal rather than the ADC. The 1.8 V AVDD simplifies power-tree design in battery-powered manpack or handheld SDRs, and the DDR LVDS output mode minimizes FPGA pin count. Designers benefit from the same 40-QFN footprint as the higher-speed LTC2257-12 and LTC2258-12, allowing one PCB to serve multiple product tiers.
מומלץ
Medical Imaging Front-End
Portable ultrasound and patient-monitoring front-ends use the LTC2256CUJ-12 to digitize conditioned analog signals at low power. With 71.1 dB SNR and only 62 mW dissipation, the ADC preserves diagnostic detail while keeping thermal rise inside sealed plastic enclosures minimal. The differential input rejects common-mode noise from long sensor cables and from nearby switching power supplies. The exposed-pad 40-QFN package makes thermal management straightforward in fan-less medical chassis, and the 0 C to +70 C commercial grade covers clinical-room deployments. For portable or field-use designs, designers step up to the LTC2256IUJ-12 industrial variant.
מומלץ
Handheld Portable Test Equipment
Battery-powered oscilloscope probes, signal analyzers, and field-strength meters leverage the LTC2256CUJ-12 to digitize up to 10 MHz of input bandwidth while drawing only 62 mW. The 1.8 V AVDD simplifies USB or Li-Ion powered designs, and the parallel CMOS output mode lets low-cost microcontrollers or FPGAs capture samples without expensive LVDS hardware. The 88 dB SFDR is more than enough for spectrum-analyzer-grade amplitude accuracy, and the exposed-pad 40-QFN keeps the analog front-end thermally isolated from the digital section. Designers reusing the same PCB across speed grades can move up to the LTC2257CUJ-12 (40 Msps) or LTC2258CUJ-12 (65 Msps) without layout changes.
מומלץ
Low-Power Industrial Instrumentation
Industrial vibration, acoustic, and process-control instruments use the LTC2256CUJ-12 to convert transducer outputs into digital streams with high dynamic range. The 12-bit resolution combined with 71.1 dB SNR lets designers detect small signals on top of large DC offsets, while the differential input rejects switching noise from motor drives and solenoid coils. The 1.8 V AVDD integrates cleanly with modern low-power MCUs, and the exposed-pad 40-QFN provides mechanical robustness for industrial enclosures. For deployments beyond 0 C to +70 C, designers migrate to the pin-compatible LTC2256IUJ-12 industrial-grade variant.
מומלץ
Wideband Communication Signal Analyzer
The LTC2256CUJ-12 is a strong fit for wideband communication signal analyzers that need to capture moderate-bandwidth signals with high linearity. Its 88 dB SFDR ensures that harmonic and intermodulation artifacts stay well below the signal of interest, while the 0.17 ps RMS jitter guarantees that wideband noise does not degrade low-level spectral measurements. The DDR LVDS output mode drives modern FPGAs at full sample rate across short board traces, and the 1.8 V supply rail simplifies integration into mixed-signal analyzer backplanes. A common 40-QFN footprint with the LTC2257-12 and LTC2258-12 lets one hardware platform address 25/40/65 Msps product tiers.
מומלץ
סיכום מוצרים מומלצים
נתוני עזר הנדסיים עבור LTC2256CUJ-12 — השוואה, הנחיות תכנון ומידע על תאימות.
מדריך בחירה
השוואה עם חלופות
| פרמטר | מוצר זה | LTC2256IUJ-12#PBF | LTC2257CUJ-12#PBF | LTC2258CUJ-12#PBF | LTC2260CUJ-12#PBF | LTC2151CUJ-14#PBF |
|---|---|---|---|---|---|---|
| Package | 40-QFN (6x6) | 40-QFN (6x6) - same | 40-QFN (6x6) - same | 40-QFN (6x6) - same | 40-QFN (6x6) - same | 40-QFN (6x6) - same |
| Brand | Analog Devices | Analog Devices | Analog Devices | Analog Devices | Analog Devices | Analog Devices |
| Resolution | 12 bit | 12 bit | 12 bit | 12 bit | 14 bit | 14 bit |
| Analog Supply Voltage | 1.8 V | 1.8 V | 1.8 V | 1.8 V | 1.8 V | 1.8 V |
| Operating Temperature | 0 C to +70 C (commercial) | -40 C to +85 C (industrial) | 0 C to +70 C | 0 C to +70 C | 0 C to +70 C | 0 C to +70 C |
| Differential Input | Yes | Yes | Yes | Yes | Yes | Yes |
מבדילים עיקריים
- Lowest power in the 12-bit 25 Msps QFN-40 class (לעומתLTC2257CUJ-12#PBF)
- Pin-compatible upgrade path to 65 Msps (לעומתLTC2258CUJ-12#PBF)
- Sub-picosecond aperture jitter enables IF undersampling (לעומתLTC2260CUJ-12#PBF)
הערות תכנון
Use a multilayer PCB with a continuous, unbroken ground plane under the LTC2256CUJ-12 - per the Analog Devices datasheet recommendation. Place 10 uF and 0.1 uF ceramic decoupling capacitors on AVDD, DVDD, and OVDD as close to their respective pins as possible. The exposed pad (EP) must be soldered to a ground copper pour that is stitched with multiple vias to the inner ground plane to minimize thermal resistance and provide a low-inductance return path for the high-speed digital outputs.
Route the differential analog inputs (AIN+/AIN-) and differential clock (CLK+/CLK-) with matched trace lengths and 100 ohm differential impedance to preserve the rated 88 dB SFDR. Keep analog input traces away from the digital output bus and the OVDD supply; if the digital outputs are DDR LVDS, route them as a 100 ohm differential pair with a ground reference plane. Place the common-mode voltage output (VCM) bypass cap close to its pin to filter reference noise.
Do not leave OVDD floating - the output mode (CMOS, DDR CMOS, DDR LVDS) depends on a valid OVDD supply between 0.5 V and 1.8 V. Ensure MODE is tied to a logic-high or logic-low level through a 10 kohm resistor at the pin, not at the FPGA, to avoid reflections. If using the internal reference, the REFT and REFB pins each require a 2.2 uF X7R ceramic bypass; omitting these caps degrades SNR by several dB.
מידע על תאימות
Lead-free and RoHS compliant per the #PBF ordering suffix. AEC-Q100 is not applicable (commercial/industrial grade). Halogen-free status not explicitly stated in the verified data and marked unknown.
