SN65HVD11D vs SN65HVD77D तुलना
विस्तृत दोनों ओर की तुलना SN65HVD11D द्वारा Texas Instruments और SN65HVD77D द्वारा Texas Instruments. मुख्य विशेषताओं, इलेक्ट्रिकल पैरामीटर, पैकेजिंग, चक्र स्थिति, मूल्यांकन और उपलब्धता को तुलना करके अपनी डिजाइन की आवश्यकताओं के लिए सबसे अच्छा घटक निर्धारित करें。
Texas Instruments
SN65HVD77D - 3.3V 50Mbps Full-Duplex RS-485 | Texas Instruments
SN65HVD77D ✓ सक्रियविशेषता तुलना
| पैरामीटर | SN65HVD11D | SN65HVD77D |
|---|---|---|
| ब्रांड | Texas Instruments | Texas Instruments |
| श्रेणी | Interface ICs | Interface ICs |
| लाइफसाइकिल स्थिति | सक्रिय | सक्रिय |
| Product Type | Differential transceiver | Full-duplex RS-485 transceiver |
| Supported Interfaces | RS-485 and RS-422 | — |
| सप्लाई वोल्टेज | 3.3 V | — |
| Driver Output State | Three-state | — |
| Receiver Architecture | Differential input | — |
| Unit Load | 1/8 unit load | — |
| Maximum Bus Nodes | Up to 256 nodes | — |
| Bus-Pin ESD Protection | Exceeds 16 kV HBM | — |
| Standards | ANSI TIA/EIA-485-A and ISO 8482:1993 | — |
| ऑपरेटिंग तापमान | -40 °C to +85 °C | — |
| पैकेज | 8-pin SOIC (D) | 8-pin SOIC (D) |
| पिन काउंट | 8 pins | — |
| माउंटिंग प्रकार | Surface mount | Surface mount |
| Output Current | [DATA_NEEDED: output current] | — |
| डेटा दर | [DATA_NEEDED: maximum data rate] | — |
| Differential Output Voltage | [DATA_NEEDED: differential output voltage] | — |
| Receiver Differential Threshold | [DATA_NEEDED: receiver differential threshold] | — |
| सप्लाई करंट | [DATA_NEEDED: operating supply current] | — |
| RoHS स्थिति | [DATA_NEEDED: RoHS status] | Compliant |
| REACH Status | [DATA_NEEDED: REACH status] | — |
| Supply Voltage Range | — | 3.0 V to 3.6 V |
| Nominal Supply Voltage | — | 3.3 V |
| Maximum Data Rate | — | 50 Mbps |
| Number of Drivers | — | 1 |
| Number of Receivers | — | 1 |
| Duplex Mode | — | Full duplex |
| Supported Standards | — | RS-485 and RS-422 |
| ESD Protection | — | ±12 kV IEC |
| ऑपरेटिंग तापमान रेंज | — | -40°C to 125°C |
| Package Width | — | 3.90 mm |
| External Enable Controls | — | None |
| Driver Output Type | — | Differential |
| Receiver Output Type | — | Single-ended logic output |
| Low-Power Standby Current | — | Less than 5 µA when driver and receiver are disabled |
| Termination Requirement | — | External termination required |