THVD1451DRBR vs SN65HVD51D तुलना
विस्तृत दोनों ओर की तुलना THVD1451DRBR द्वारा Texas Instruments और SN65HVD51D द्वारा Texas Instruments. मुख्य विशेषताओं, इलेक्ट्रिकल पैरामीटर, पैकेजिंग, चक्र स्थिति, मूल्यांकन और उपलब्धता को तुलना करके अपनी डिजाइन की आवश्यकताओं के लिए सबसे अच्छा घटक निर्धारित करें。
Texas Instruments
SN65HVD51D - 5Mbps Full-Duplex RS-485 Transceiver | Texas Instruments
SN65HVD51D ✓ सक्रियविशेषता तुलना
| पैरामीटर | THVD1451DRBR | SN65HVD51D |
|---|---|---|
| ब्रांड | Texas Instruments | Texas Instruments |
| श्रेणी | Interface ICs | Interface ICs |
| लाइफसाइकिल स्थिति | सक्रिय | सक्रिय |
| फ़ंक्शन | RS-485 transceiver (1 driver / 1 receiver) | — |
| Protocol | RS-485 / RS-422 | — |
| Supply Voltage Range | 3.0 V to 5.5 V | 4.5 V to 5.5 V |
| ऑपरेटिंग तापमान रेंज | -40 °C to +125 °C | -40 °C to 85 °C |
| Signaling Rate (Maximum) | 50 Mbps | — |
| Number of Nodes on Bus | Up to 256 (1/8 unit load) | — |
| IEC 61000-4-2 Contact Discharge ESD | ±18 kV (bus pins) | — |
| IEC 61000-4-2 Air-Gap Discharge ESD | ±8 kV (bus pins) | — |
| IEC 61000-4-4 EFT | ±4 kV | — |
| Common-Mode Voltage Range | -7 V to +12 V | — |
| Receiver Input Hysteresis | 30 mV (typical) | — |
| Standby / Shutdown Current | < 5 µA | — |
| पैकेज | VSON-8 (DRB) 3x3 mm with exposed thermal pad | 8-pin SOIC (D) |
| माउंटिंग प्रकार | Surface Mount | Surface mount |
| MSL Moisture Sensitivity | MSL 1 | — |
| RoHS स्थिति | Compliant | [DATA_NEEDED: RoHS compliance status] |
| पिन की संख्या | 8 | — |
| Duplex | Half-Duplex | — |
| Product Type | — | RS-422/RS-485 full-duplex transceiver |
| Driver Count | — | 1 driver |
| Receiver Count | — | 1 receiver |
| Maximum Signaling Rate | — | 5 Mbps |
| Interface Standards | — | RS-422 and RS-485 |
| Duplex Mode | — | Full-duplex |
| Receiver Unit Load | — | 1/8 unit load |
| Maximum Bus Nodes | — | Up to 256 nodes |
| Bus-Pin ESD Protection | — | Exceeds 15 kV HBM |
| Available Driver Transition Rates | — | 1 Mbps, 5 Mbps, and 25 Mbps |
| Standby Current | — | Less than 1 µA |
| Enable Architecture | — | Fully enabled; no external enable pins |
| REACH Status | — | [DATA_NEEDED: REACH compliance status] |