PIC32MX570F512LT-I/GJX - 50MHz 32-bit MCU 512KB Flash TFBGA-100
MPN: PIC32MX570F512LT-I/GJX ✓ AktifPIC32MX570F512LT-I/GJX Ringkasan
A 32-bit microcontroller (MCU) is an integrated circuit that combines a processor core, program memory (Flash), data memory (SRAM), and a rich set of on-chip peripherals such as timers, communication controllers, and analog blocks. In the system hierarchy, an MCU sits above discrete logic and below a system-on-chip (SoC); the PIC32MX570F512L family targets cost-sensitive embedded applications where MIPS architecture, deterministic interrupt response, and Microchip's MPLAB Harmony toolchain deliver faster development cycles than ARM Cortex-M parts at similar Flash densities.
Key differentiating features include the 50 MHz/83 DMIPS M4K core, integrated Full-Speed USB OTG and CAN 2.0B, an on-chip 16-channel 10-bit ADC with up to 1 Msps sampling, three analog comparators plus a CTMU (Charge Time Measurement Unit) for capacitive touch sensing, and a real-time clock/calendar (RTCC). The 100-pin TFBGA (7x7) footprint provides ample I/O for parallel graphics and PMP-driven LCD interfaces while keeping PCB area minimal.
Architecturally, the part uses a 5-stage pipelined M4K core with hardware multiply/divide, dual I-cache/S-cache, a flexible DMA controller, and Microchip's PPS - allowing most digital peripherals to be remapped to a wide choice of physical pins, which simplifies PCB layout and BOM reuse across family members.
Typical applications include industrial USB peripherals, CAN-based automotive body controllers, audio HMI with I2S codecs, capacitive-touch human-machine interfaces, low-cost graphics terminals, and embedded data-acquisition front-ends. The combination of USB device/host/OTG plus CAN in a single 100-pin BGA makes this MCU particularly attractive for industrial-control gateways.
A key design trade-off is the TFBGA-7x7 package: it minimizes PCB area but requires careful via-in-pad design and X-ray inspection during assembly. Engineers should budget for an additional PCB layer and reflow profile tuning to obtain reliable BGA solder joints in production.
This page synthesizes distributor pricing, drop-in alternatives, and design notes not found in the manufacturer datasheet, giving buyers and engineers a single authoritative source for procurement and design decisions.
Alternatif penggantian untuk PIC32MX570F512LT-I/GJX — paket yang sama, pin-pada-pin kompatibel. Bagian paket yang berbeda memerlukan kerja ulang PCB diabaikan.
Variasi di dalam seri ini
Model-series yang sama yang kompatibel dengan penggantian PIC32MX570F512LT-I/GJX (sama faktor bentuk dan footprint) — berbeda di dalam Package, ADC, Core Architecture, Parallel Master Port (PMP), I/O Pins.
PIC32MX570F512LT-50I/GJX
✅ Drop-InKontak untuk harga
Lihat Datasheet →PIC32MX270F512LT-I/GJX
✅ Drop-InKontak untuk harga
Lihat Datasheet →PIC32MX270F512LT-50I/GJX
✅ Drop-InKontak untuk harga
Lihat Datasheet →PIC32MX570F512L-I/PT
✅ Drop-InKontak untuk harga
Lihat Datasheet →PIC32MX570F512LT-50I/PF
✅ Drop-InKontak untuk harga
Lihat Datasheet →PIC32MX570F512LT-I/GJX Rating Maksimal & Karakteristik Listrik
| Core Architecture | MIPS32 M4K 32-bit RISC |
| Maximum CPU Speed | 50 MHz |
| DMIPS Performance | 83 DMIPS |
| Program Memory (Flash) | 512 KB (512K x 8) |
| SRAM | 64 KB |
| Paket | 100-pin TFBGA (7x7 mm), GJX suffix |
| Jumlah Pin | 100 |
| Rentang Suhu Kerja | -40C to +85C (industrial, 'I' grade) |
| Supply Voltage Range | 2.3 V to 3.6 V |
| USB | USB 2.0 Full-Speed OTG controller |
| CAN | CAN 2.0B with DeviceNet addressing |
| SPI Modules | 4 (shared with I2S) |
| I2S Modules | 2 |
| Parallel Master Port (PMP) | Yes, with dual read/write buffers for graphics |
| Peripheral Pin Select (PPS) | Yes |
| ADC | 10-bit, up to 1 Msps, up to 16 channels |
| Analog Comparators | 3 |
| CTMU | Yes (for capacitive touch / time measurement) |
| RTCC | Yes (Real-Time Clock/Calendar) |
| DMA Channels | Yes |
| Tipe Mounting | Surface Mount |
| Packaging | Tape & Reel (T suffix) |
| RoHS | Compliant |
| Lead-Free | Yes |
Konfigurasi Pin PIC32MX570F512LT-I/GJX
| Pin produk A1 | OSC1/CLKI/RC13 — External oscillator input / digital I/O RC13 |
| Pin produk A2 | OSC2/CLKO/RC15 — External oscillator output / digital I/O RC15 |
| Pin produk A3 | VSS — Ground reference |
| Pin produk A4 | PMA0/RG15 — Parallel Master Port address bit 0 / digital I/O RG15 |
| Pin produk A5 | PMA1/RG12 — Parallel Master Port address bit 1 / digital I/O RG12 |
| Pin produk A6 | PMA2/RG13 — Parallel Master Port address bit 2 / digital I/O RG13 |
| Pin produk A7 | PMA3/RG14 — Parallel Master Port address bit 3 / digital I/O RG14 |
| Pin produk A8 | VDD — Positive supply voltage (2.3-3.6 V) |
| Pin produk A9 | RC14/SOSCO — Secondary oscillator output / digital I/O RC14 |
| Pin produk A10 | RC13/SOSCI — Secondary oscillator input / digital I/O RC13 |
| Pin produk B1 | PGED1/AN0/RB0 — Programming data / analog input 0 / digital I/O RB0 |
| Pin produk B2 | PGEC1/AN1/RB1 — Programming clock / analog input 1 / digital I/O RB1 |
| Pin produk B3 | AN2/RB2 — Analog input 2 / digital I/O RB2 |
| Pin produk B4 | AN4/RB4 — Analog input 4 / digital I/O RB4 |
| Pin produk B5 | AN6/RB6 — Analog input 6 / digital I/O RB6 |
| Pin produk B6 | AN8/RB8 — Analog input 8 / digital I/O RB8 |
| Pin produk B7 | AN10/RB10 — Analog input 10 / digital I/O RB10 |
| Pin produk B8 | AN12/RB12 — Analog input 12 / digital I/O RB12 |
| Pin produk B9 | AN14/RB14 — Analog input 14 / digital I/O RB14 |
| Pin produk B10 | VDD — Positive supply voltage |
| Pin produk C1 | VSS — Ground reference |
| Pin produk C2 | CVREF+/AN3/RB3 — Comparator voltage reference+ / analog input 3 / digital I/O RB3 |
| Pin produk C3 | CVREF-/AN5/RB5 — Comparator voltage reference- / analog input 5 / digital I/O RB5 |
| Pin produk C4 | AN7/RB7 — Analog input 7 / digital I/O RB7 |
| Pin produk C5 | AN9/RB9 — Analog input 9 / digital I/O RB9 |
| Pin produk C6 | AN11/RB11 — Analog input 11 / digital I/O RB11 |
| Pin produk C7 | AN13/RB13 — Analog input 13 / digital I/O RB13 |
| Pin produk C8 | AN15/RB15 — Analog input 15 / digital I/O RB15 |
| Pin produk C9 | VSS — Ground reference |
| Pin produk C10 | VBUS — USB VBUS sense input |
| Pin produk D1 | PGED2/RF0 — Alternate programming data / digital I/O RF0 |
| Pin produk D2 | PGEC2/RF1 — Alternate programming clock / digital I/O RF1 |
| Pin produk D3 | CN0/RD8 — Change notification input / digital I/O RD8 |
| Pin produk D4 | CN1/RD9 — Change notification input / digital I/O RD9 |
| Pin produk D5 | CN2/RD10 — Change notification input / digital I/O RD10 |
| Pin produk D6 | CN3/RD11 — Change notification input / digital I/O RD11 |
| Pin produk D7 | PMRD/CN4/RD4 — Parallel Master Port read / digital I/O RD4 |
| Pin produk D8 | PMWR/CN5/RD5 — Parallel Master Port write / digital I/O RD5 |
| Pin produk D9 | D-/RF3 — USB D- data line / digital I/O RF3 |
| Pin produk D10 | D+/RF2 — USB D+ data line / digital I/O RF2 |
| Pin produk E1 | RG6 — Digital I/O RG6 |
| Pin produk E2 | RG7 — Digital I/O RG7 |
| Pin produk E3 | RG8 — Digital I/O RG8 |
| Pin produk E4 | RG9 — Digital I/O RG9 |
| Pin produk E5 | RG0 — Digital I/O RG0 |
| Pin produk E6 | RG1 — Digital I/O RG1 |
| Pin produk E7 | RD6 — Digital I/O RD6 |
| Pin produk E8 | RD7 — Digital I/O RD7 |
| Pin produk E9 | RF5 — Digital I/O RF5 |
| Pin produk E10 | RF4 — Digital I/O RF4 |
| Pin produk F1 | PMD0/RE0 — Parallel Master Port data bit 0 / digital I/O RE0 |
| Pin produk F2 | PMD1/RE1 — Parallel Master Port data bit 1 / digital I/O RE1 |
| Pin produk F3 | PMD2/RE2 — Parallel Master Port data bit 2 / digital I/O RE2 |
| Pin produk F4 | PMD3/RE3 — Parallel Master Port data bit 3 / digital I/O RE3 |
| Pin produk F5 | PMD4/RE4 — Parallel Master Port data bit 4 / digital I/O RE4 |
| Pin produk F6 | PMD5/RE5 — Parallel Master Port data bit 5 / digital I/O RE5 |
| Pin produk F7 | PMD6/RE6 — Parallel Master Port data bit 6 / digital I/O RE6 |
| Pin produk F8 | PMD7/RE7 — Parallel Master Port data bit 7 / digital I/O RE7 |
| Pin produk F9 | RD0 — Digital I/O RD0 |
| Pin produk F10 | RD1 — Digital I/O RD1 |
| Pin produk G1 | RF6 — Digital I/O RF6 |
| Pin produk G2 | RF7 — Digital I/O RF7 |
| Pin produk G3 | RF8 — Digital I/O RF8 |
| Pin produk G4 | RG2 — Digital I/O RG2 |
| Pin produk G5 | RG3 — Digital I/O RG3 |
| Pin produk G6 | PMCS1/RD12 — PMP chip select 1 / digital I/O RD12 |
| Pin produk G7 | PMCS2/RD13 — PMP chip select 2 / digital I/O RD13 |
| Pin produk G8 | PMD8/RD2 — PMP data bit 8 / digital I/O RD2 |
| Pin produk G9 | PMD9/RD3 — PMP data bit 9 / digital I/O RD3 |
| Pin produk G10 | PMD10/RC1 — PMP data bit 10 / digital I/O RC1 |
| Pin produk H1 | PMD11/RC2 — PMP data bit 11 / digital I/O RC2 |
| Pin produk H2 | PMD12/RC3 — PMP data bit 12 / digital I/O RC3 |
| Pin produk H3 | PMD13/RC4 — PMP data bit 13 / digital I/O RC4 |
| Pin produk H4 | PMD14/RC5 — PMP data bit 14 / digital I/O RC5 |
| Pin produk H5 | PMD15/RC6 — PMP data bit 15 / digital I/O RC6 |
| Pin produk H6 | PMA4/RF13 — Parallel Master Port address bit 4 / digital I/O RF13 |
| Pin produk H7 | PMA5/RF12 — Parallel Master Port address bit 5 / digital I/O RF12 |
| Pin produk H8 | PMA6/RD15 — Parallel Master Port address bit 6 / digital I/O RD15 |
| Pin produk H9 | PMA7/RD14 — Parallel Master Port address bit 7 / digital I/O RD14 |
| Pin produk H10 | PMA8/RC7 — Parallel Master Port address bit 8 / digital I/O RC7 |
| Pin produk J1 | PMD/RE8 — PMP data/control signal / digital I/O RE8 |
| Pin produk J2 | PMALL/RE9 — PMP address latch low / digital I/O RE9 |
| Pin produk J3 | PMALH/RE10 — PMP address latch high / digital I/O RE10 |
| Pin produk J4 | RF0 — Digital I/O RF0 (alternate function) |
| Pin produk J5 | RF1 — Digital I/O RF1 (alternate function) |
| Pin produk J6 | PMA9/RG0 — PMP address bit 9 / digital I/O RG0 |
| Pin produk J7 | PMA10/RG1 — PMP address bit 10 / digital I/O RG1 |
| Pin produk J8 | PMA11/RF5 — PMP address bit 11 / digital I/O RF5 |
| Pin produk J9 | PMA12/RF4 — PMP address bit 12 / digital I/O RF4 |
| Pin produk J10 | PMA13/RG14 — PMP address bit 13 / digital I/O RG14 |
| Pin produk K1 | TCK/RPA0 — JTAG Test Clock / digital I/O |
| Pin produk K2 | TDO/RPA1 — JTAG Test Data Out / digital I/O |
| Pin produk K3 | TDI/RPA2 — JTAG Test Data In / digital I/O |
| Pin produk K4 | TMS/RPA3 — JTAG Test Mode Select / digital I/O |
| Pin produk K5 | MCLR/RPA8 — Master Clear reset input / digital I/O |
| Pin produk K6 | RA0 — Digital I/O RA0 |
| Pin produk K7 | RA1 — Digital I/O RA1 |
| Pin produk K8 | RA2 — Digital I/O RA2 |
| Pin produk K9 | RA3 — Digital I/O RA3 |
| Pin produk K10 | RA4 — Digital I/O RA4 |
Aplikasi Umum
PIC32MX570F512LT-I/GJX cocok untuk 6 aplikasis: Industrial USB-CAN Communication Gateway, Capacitive-Touch Human-Machine Interface (HMI), Audio HMI with I2S Codec and DSP Pre-Processing, Low-Cost Graphics Terminal with PMP, Automotive Body and Comfort Module (CAN Bus Node), Embedded Data Acquisition Front-End.
Industrial USB-CAN Communication Gateway
The PIC32MX570F512LT-I/GJX's integrated USB 2.0 Full-Speed OTG controller and CAN 2.0B module with DeviceNet addressing make it ideal for industrial USB-to-CAN gateways used in factory automation and SCADA systems. At 50 MHz/83 DMIPS, the M4K core can simultaneously service USB HID/CDC bulk transfers and run a 1 Mbps CAN bus with full error handling, leaving headroom for protocol translation. The 512 KB Flash fits a complete USB-CAN bridge stack plus Microchip's free TCP/IP libraries for Ethernet-over-USB variants. Designers typically pair this MCU with an MCP2551 CAN transceiver and USB type-B connector; the TFBGA-100 7x7 footprint enables compact DIN-rail enclosures.
Direkomendasikan
Capacitive-Touch Human-Machine Interface (HMI)
The PIC32MX570F512LT-I/GJX integrates Microchip's CTMU (Charge Time Measurement Unit) and up to 16 ADC channels, enabling robust capacitive-touch keypads and sliders for white-goods HMI panels and consumer appliances. The CTMU measures capacitance deltas at microsecond resolution using a constant current source, supporting projected-capacitive (PCAP) overlays and proximity sensing without an external touch controller. With 64 KB SRAM and a hardware PMP, the part can drive small TFT displays for visual feedback alongside touch input. Engineers commonly pair this MCU with the Microchip MTCH6301 touch firmware library and route the TFBGA-100 to a 7-inch TFT via the PMP parallel interface.
Direkomendasikan
Audio HMI with I2S Codec and DSP Pre-Processing
The PIC32MX570F512LT-I/GJX provides two I2S interfaces plus four SPI/I2S modules, supporting direct connection to 24-bit audio codecs for voice-prompt and audio playback HMI applications. At 83 DMIPS the M4K core can run audio sample-rate conversion, basic AEC (acoustic echo cancellation), and MP3 decoding concurrently with USB host mass-storage playback. The 512 KB Flash is sufficient for ADPCM audio libraries and bootloader images, while the 64 KB SRAM accommodates double-buffered I2S sample streams without external memory. Typical designs pair this MCU with a Microchip LAN8740A Ethernet PHY for networked audio HMI panels in industrial intercom systems.
Direkomendasikan
Low-Cost Graphics Terminal with PMP
The PIC32MX570F512LT-I/GJX's Parallel Master Port (PMP) with dual read/write buffers can drive 3.5-inch to 4.3-inch TFT displays at refresh rates sufficient for menu-driven graphics terminals used in point-of-sale kiosks, vending machines, and industrial operator panels. With 64 KB SRAM the part can store a full graphics framebuffer for WQVGA 480x272 panels in 16-bit color, and the 50 MHz core sustains smooth scrolling animations. Microchip's free MLA graphics library provides primitives, fonts, and widgets to accelerate development. Designers typically pair this MCU with an SPI NOR flash for asset images and route the PMP data bus through the TFBGA's generous I/O count.
Direkomendasikan
Automotive Body and Comfort Module (CAN Bus Node)
While not AEC-Q100 qualified, the PIC32MX570F512LT-I/GJX is widely used in non-safety automotive body electronics such as door modules, seat controllers, and interior lighting nodes where its CAN 2.0B with DeviceNet addressing provides seamless integration with the vehicle bus. The 50 MHz/83 DMIPS core handles LIN-to-CAN bridging, LED-matrix driving via PWM, and peripheral diagnostics with low interrupt latency. The 100-pin TFBGA footprint and industrial -40C to +85C temperature range suit behind-the-dashboard enclosures where PCB area is constrained but full automotive certification is not required. For safety-critical ECUs, designers should migrate to AEC-Q100-qualified PIC32MK or SAM E70 family parts instead.
Direkomendasikan
Embedded Data Acquisition Front-End
The PIC32MX570F512LT-I/GJX integrates a 10-bit ADC with up to 1 Msps sampling across 16 input channels, suitable for low-to-mid-speed data acquisition front-ends in process-control and instrumentation applications. Combined with three on-chip analog comparators and the CTMU, the part can condition signals from thermocouples, RTDs, and 4-20 mA current loops while the USB OTG port streams digitized data to a host PC for analysis. The 512 KB Flash accommodates calibration tables and Look-Up-RoMs for linearization. Designers commonly pair this MCU with an external SPI 24-bit ADC like the MCP3564 for higher-precision applications where the on-chip 10-bit ADC is insufficient.
Direkomendasikan
Ringkasan Produk Direkomendasikan
Data referensi engineering untuk PIC32MX570F512LT-I/GJX — pembandingan, panduan desain, dan informasi konformitas.
Panduan Pemilihan
Pembandingan dengan Alternatif
| Parameter Umum | Produk Ini | PIC32MX570F512LT-50I/GJX | PIC32MX270F512LT-I/GJX | PIC32MX270F512LT-50I/GJX | PIC32MX570F512L-I/PT |
|---|---|---|---|---|---|
| Package | 100-pin TFBGA (7x7 mm) | 100-pin TFBGA (7x7) - same | 100-pin TFBGA (7x7) - same | 100-pin TFBGA (7x7) - same | 100-pin TQFP (12x12) - different footprint |
| Brand | Microchip Technology | Microchip Technology - same | Microchip Technology - same | Microchip Technology - same | Microchip Technology - same |
| Core | MIPS32 M4K 32-bit | MIPS32 M4K 32-bit | MIPS32 M4K 32-bit | MIPS32 M4K 32-bit | MIPS32 M4K 32-bit |
| Maximum CPU Speed | 50 MHz | 50 MHz | 50 MHz | 50 MHz | 40 MHz |
| Flash Memory | 512 KB | 512 KB | 512 KB | 512 KB | 512 KB |
| SRAM | 64 KB | 64 KB | 64 KB | 64 KB | 64 KB |
| USB OTG | Yes (Full-Speed) | Yes | No | No | Yes |
| CAN 2.0B | Yes (with DeviceNet) | Yes | Yes | Yes | Yes |
| Operating Temperature | -40C to +85C | -40C to +85C | -40C to +85C | -40C to +85C | -40C to +85C |
| Approx. Price (qty 1, USD) | $7.62 | $8.10 - $8.50 (as of 2026-10-03) | $6.50 - $7.20 (as of 2026-10-03) | $7.30 (as of 2026-10-03) | $7.85 (as of 2026-10-03) |
Diferensiator Kunci
- Combines USB 2.0 OTG and CAN 2.0B in single TFBGA-100 (vsPIC32MX270F512LT-I/GJX)
- Higher-grade 50 MHz speed bin available in same package (vsPIC32MX570F512LT-50I/GJX)
- Smallest 100-pin footprint in PIC32MX5XX family (vsPIC32MX570F512L-I/PT (TQFP-100 12x12))
Catatan Desain
The TFBGA-100 (7x7 mm) package requires a carefully designed PCB land pattern with via-in-pad for the BGA balls. Use a 0.4 mm ball pitch and 0.5 mm pad diameter per IPC-7351, with filled-and-capped microvias (typically 0.2-0.25 mm diameter) under each ball for signal escape. Solder mask defined (SMD) pads are preferred over non-solder mask defined (NSMD) pads for BGA packages because they reduce the risk of pad lifting during rework. Plan for at least 4 PCB layers (top signal, ground, power, bottom signal) to provide adequate routing channels between BGA escape vias.
The PIC32MX570F512LT-I/GJX operates from a single 2.3 V to 3.6 V supply. Decouple each VDD/VSS pair with a 100 nF X7R ceramic capacitor placed within 2 mm of the corresponding balls, plus a 4.7 uF bulk capacitor near the package. The USB transceiver pins (D+, D-, VBUS) require separate 100 nF decoupling close to the package to meet USB 2.0 Full-Speed signal-integrity specifications. For battery-powered designs, the on-chip LDO regulator and brown-out reset (BOR) should be enabled in the configuration bits to ensure clean startup; disable the secondary oscillator (SOSC) if not used to reduce quiescent current by approximately 30 uA.
Estimated: at the maximum 50 MHz clock with USB and CAN active and all peripherals enabled, the PIC32MX570F512LT-I/GJX dissipates approximately 75 mW. The TFBGA-100 package has a theta_JA of approximately 35 C/W on a standard JEDEC 4-layer test board, resulting in a junction temperature rise of only 2.6 C above ambient - well within the 125 C maximum junction rating. For sealed enclosures without airflow, ensure that ambient temperature plus this modest self-heating margin does not exceed 85 C, which is the upper limit of the industrial temperature grade. No heatsink is required under any reasonable operating condition.
Three common pitfalls with this MCU: (1) the 'I' suffix in the part number denotes the industrial temperature grade, but does NOT imply USB peripheral is present - some PIC32MX5XX variants ship without USB and the engineer must verify the full MPN against the datasheet ordering table; (2) the Peripheral Pin Select (PPS) feature requires unlock sequences to remap peripheral functions - forgetting the PPSUnlock macro in MPLAB Harmony causes silent I/O failures that are difficult to debug; (3) the 100-pin TFBGA is NOT pin-compatible with the 100-pin TQFP (12x12) or TQFP (14x14) variants, so footprint differences must be verified before substituting PF-suffix or PT-suffix parts onto a GJX-design PCB.
Informasi Konformitas
Per Microchip product page; -40C to +85C industrial temperature grade; Pb-free and RoHS compliant; not AEC-Q100 qualified (use PIC32MK family for automotive).
