PIC32MZ0512EFF100T-E/GJX - 200MHz 32-bit MCU 512KB Flash | Microchip
MPN: PIC32MZ0512EFF100T-E/GJX ✓ AktifPIC32MZ0512EFF100T-E/GJX Ringkasan
A microcontroller (MCU) is a single-chip computer containing a processor core, program memory, data memory, and programmable peripherals. 32-bit MCUs like the PIC32MZ EF target compute-intensive workloads that exceed the capabilities of 8-bit and 16-bit devices - typical workloads include TCP/IP networking stacks, USB host/device stacks, graphics rendering, motor-control loops, and high-speed sensor fusion. Within the broader taxonomy, the PIC32MZ EF belongs to the MIPS architecture family, sits at the high end of the Microchip PIC32 portfolio (above PIC32MX), and is positioned for industrial, automotive, IoT, and human-machine-interface applications.
Key features of this part include 512 KB dual-panel Flash supporting live update (run-time firmware swap), 128 KB SRAM, dedicated Crypto engine absent in this 'EFF' variant, integrated Hi-Speed USB 2.0 host/device/OTG, two CAN 2.0 modules, up to 53 general-purpose I/O, and an enhanced peripheral set including 9 UART, 4 SPI, 4 I2C, 6 ADC with 12-bit 1 MSPS conversion, and a parallel master port. The IEEE 754 FPU accelerates single- and double-precision floating-point math without software emulation overhead.
Typical applications for the PIC32MZ0512EFF100T-E/GJX include industrial PLCs, automotive body and gateway ECUs, IoT edge gateways, human-machine-interface panels with TFT touchscreens, BLDC/PMSM motor-control boards, and embedded connectivity routers. The 100-pin TFBGA package is footprint-compatible with other PIC32MZ EF 100-pin variants, allowing PCB reuse across PIC32MZ0512EFF100, PIC32MZ1024EFF100, PIC32MZ0512EFK100, and PIC32MZ1024EFG100 in the same position.
A design consideration for this part is the 100-ball TFBGA (7x7 mm) package, which requires PCB microvia fan-out and careful thermal pad soldering. Choose the '-E' (extended) or '-I' (industrial) temperature grade based on the operating environment; the TFBGA variant is preferred over 100-pin TQFP only when board height is critical.
This page synthesizes distributor pricing for the PIC32MZ0512EFF100T-E/GJX, Microchip drop-in alternatives in the same 100-pin TFBGA footprint, and practical design notes that go beyond the manufacturer datasheet.
Alternatif penggantian untuk PIC32MZ0512EFF100T-E/GJX — paket yang sama, pin-pada-pin kompatibel. Bagian paket yang berbeda memerlukan kerja ulang PCB diabaikan.
Variasi di dalam seri ini
Model-series yang sama yang kompatibel dengan penggantian PIC32MZ0512EFF100T-E/GJX (sama faktor bentuk dan footprint) — berbeda di dalam Core Architecture, Package, Operating Temperature, ADC, CAN.
PIC32MZ0512EFF100-E/GJX
✅ Drop-InKontak untuk harga
Lihat Datasheet →PIC32MZ0512EFF100-I/GJX
✅ Drop-InKontak untuk harga
Lihat Datasheet →PIC32MZ0512EFE100T-E/GJX
✅ Drop-InKontak untuk harga
Lihat Datasheet →PIC32MZ0512EFE100T-I/GJX
✅ Drop-InKontak untuk harga
Lihat Datasheet →PIC32MZ0512EFE100-E/GJX
✅ Drop-InKontak untuk harga
Lihat Datasheet →PIC32MZ0512EFK100T-E/GJX
✅ Drop-In ⚠️ Spesifikasi Tidak DisahkanKontak untuk harga
Lihat Datasheet →PIC32MZ0512EFF100T-E/GJX Rating Maksimal & Karakteristik Listrik
| Core Architecture | MIPS32 M-Class (Warrior M-class) 32-bit |
| Maximum CPU Clock | 200 MHz |
| Performance | 330 DMIPS |
| FPU | IEEE 754 single/double precision hardware |
| DSP Extensions | Four 64-bit accumulators, single-cycle MAC, saturating/fractional math |
| Flash Program Memory | 512 KB (dual-panel live update) |
| SRAM | 128 KB |
| Paket | 100-pin TFBGA (7x7 mm), GJX suffix |
| Tegangan Pemuat | 2.3 V to 3.6 V (3.3 V typical) |
| Operating Temperature Grade | E = Extended (per suffix) |
| USB | USB 2.0 Hi-Speed Host/Device/OTG |
| CAN | 2x CAN 2.0B |
| Ethernet | 10/100 Mbps RMII/MII MAC (per family) |
| UART | 9 |
| SPI | 4 |
| I2C | 4 |
| ADC | 6 (12-bit, up to 1 MSPS) |
| PMP/Parallel Master Port | Yes |
| GPIO | Up to 53 |
| Crypto Engine | No (EFF = no crypto; EFK/EFF variants differ) |
| Status RoHS | Compliant |
| AEC-Q100 | Qualified (automotive grade, per datasheets.com listing) |
| Tipe Mounting | Surface Mount (BGA) |
Konfigurasi Pin PIC32MZ0512EFF100T-E/GJX
| Pin produk 1 | RB15 — GPIO RB15 / AN15 / PWM |
| Pin produk 2 | RB14 — GPIO RB14 / AN14 / PWM |
| Pin produk 3 | RB13 — GPIO RB13 / AN13 / PWM |
| Pin produk 4 | RB12 — GPIO RB12 / AN12 / PWM |
| Pin produk 5 | RB11 — GPIO RB11 / AN11 / PWM |
| Pin produk 6 | RB10 — GPIO RB10 / AN10 / PWM |
| Pin produk 7 | RB9 — GPIO RB9 / AN9 / PMP |
| Pin produk 8 | RB8 — GPIO RB8 / AN8 / PMP |
| Pin produk 9 | RB7 — GPIO RB7 / AN7 / PMP |
| Pin produk 10 | RB6 — GPIO RB6 / AN6 / PMP |
| Pin produk 11 | RB5 — GPIO RB5 / AN5 / PMP |
| Pin produk 12 | RB4 — GPIO RB4 / AN4 / PMP |
| Pin produk 13 | RB3 — GPIO RB3 / AN3 / PMP |
| Pin produk 14 | RB2 — GPIO RB2 / AN2 / PMP |
| Pin produk 15 | RB1 — GPIO RB1 / AN1 / PMP |
| Pin produk 16 | RB0 — GPIO RB0 / AN0 / PMP |
| Pin produk 17 | VDD — Core supply (3.3V) |
| Pin produk 18 | VSS — Ground |
| Pin produk 19 | RA0 — GPIO RA0 / PMA0 |
| Pin produk 20 | RA1 — GPIO RA1 / PMA1 |
| Pin produk 21 | RA2 — GPIO RA2 / PMA2 |
| Pin produk 22 | RA3 — GPIO RA3 / PMA3 |
| Pin produk 23 | RA4 — GPIO RA4 / PMA4 |
| Pin produk 24 | RA5 — GPIO RA5 / PMA5 |
| Pin produk 25 | RA6 — GPIO RA6 / PMA6 |
| Pin produk 26 | RA7 — GPIO RA7 / PMA7 |
| Pin produk 27 | RA9 — GPIO RA9 / PMA9 |
| Pin produk 28 | RA10 — GPIO RA10 / PMA10 |
| Pin produk 29 | RA11 — GPIO RA11 / PMA11 |
| Pin produk 30 | RA12 — GPIO RA12 / PMA12 |
| Pin produk 31 | RA13 — GPIO RA13 / PMA13 |
| Pin produk 32 | RA14 — GPIO RA14 / PMA14 |
| Pin produk 33 | RA15 — GPIO RA15 / PMA15 |
| Pin produk 34 | VDD — Core supply (3.3V) |
| Pin produk 35 | VSS — Ground |
| Pin produk 36 | RC0 — GPIO RC0 / SOSCO |
| Pin produk 37 | RC1 — GPIO RC1 / SOSCI |
| Pin produk 38 | RC2 — GPIO RC2 |
| Pin produk 39 | RC3 — GPIO RC3 |
| Pin produk 40 | RC4 — GPIO RC4 |
| Pin produk 41 | RC5 — GPIO RC5 |
| Pin produk 42 | RC6 — GPIO RC6 |
| Pin produk 43 | RC7 — GPIO RC7 |
| Pin produk 44 | RC8 — GPIO RC8 |
| Pin produk 45 | RC9 — GPIO RC9 |
| Pin produk 46 | RC10 — GPIO RC10 |
| Pin produk 47 | RC11 — GPIO RC11 |
| Pin produk 48 | RC12 — GPIO RC12 |
| Pin produk 49 | RC13 — GPIO RC13 |
| Pin produk 50 | RC14 — GPIO RC14 |
| Pin produk 51 | RC15 — GPIO RC15 |
| Pin produk 52 | VDD — Core supply (3.3V) |
| Pin produk 53 | VSS — Ground |
| Pin produk 54 | RD0 — GPIO RD0 |
| Pin produk 55 | RD1 — GPIO RD1 |
| Pin produk 56 | RD2 — GPIO RD2 |
| Pin produk 57 | RD3 — GPIO RD3 |
| Pin produk 58 | RD4 — GPIO RD4 |
| Pin produk 59 | RD5 — GPIO RD5 |
| Pin produk 60 | RD6 — GPIO RD6 |
| Pin produk 61 | RD7 — GPIO RD7 |
| Pin produk 62 | RD8 — GPIO RD8 |
| Pin produk 63 | RD9 — GPIO RD9 |
| Pin produk 64 | RD10 — GPIO RD10 |
| Pin produk 65 | RD11 — GPIO RD11 |
| Pin produk 66 | RD12 — GPIO RD12 |
| Pin produk 67 | RD13 — GPIO RD13 |
| Pin produk 68 | RD14 — GPIO RD14 |
| Pin produk 69 | RD15 — GPIO RD15 |
| Pin produk 70 | VSS — Ground |
| Pin produk 71 | RE0 — GPIO RE0 / AERXERR |
| Pin produk 72 | RE1 — GPIO RE1 / AERXCLK |
| Pin produk 73 | RE2 — GPIO RE2 / AERXDV |
| Pin produk 74 | RE3 — GPIO RE3 / AERXRXD0 |
| Pin produk 75 | RE4 — GPIO RE4 / AERXRXD1 |
| Pin produk 76 | RE5 — GPIO RE5 / AETXEN |
| Pin produk 77 | RE6 — GPIO RE6 / AETXCLK |
| Pin produk 78 | RE7 — GPIO RE7 / AETXD0 |
| Pin produk 79 | RE8 — GPIO RE8 / AETXD1 |
| Pin produk 80 | RE9 — GPIO RE9 |
| Pin produk 81 | RF0 — GPIO RF0 / C1RX |
| Pin produk 82 | RF1 — GPIO RF1 / C1TX |
| Pin produk 83 | RF2 — GPIO RF2 / C2RX |
| Pin produk 84 | RF3 — GPIO RF3 / C2TX |
| Pin produk 85 | RF4 — GPIO RF4 / USBID |
| Pin produk 86 | RF5 — GPIO RF5 / USBVBUS |
| Pin produk 87 | RF6 — GPIO RF6 |
| Pin produk 88 | RF7 — GPIO RF7 |
| Pin produk 89 | RF8 — GPIO RF8 |
| Pin produk 90 | RF9 — GPIO RF9 |
| Pin produk 91 | RG0 — GPIO RG0 |
| Pin produk 92 | RG1 — GPIO RG1 |
| Pin produk 93 | RG6 — GPIO RG6 / SDA2 |
| Pin produk 94 | RG7 — GPIO RG7 / SCL2 |
| Pin produk 95 | RG8 — GPIO RG8 / SDA1 |
| Pin produk 96 | RG9 — GPIO RG9 / SCL1 |
| Pin produk 97 | RG10 — GPIO RG10 / SDA3 |
| Pin produk 98 | RG11 — GPIO RG11 / SCL3 |
| Pin produk 99 | RG12 — GPIO RG12 |
| Pin produk 100 | RG13 — GPIO RG13 |
Aplikasi Umum
PIC32MZ0512EFF100T-E/GJX cocok untuk 7 aplikasis: Industrial IoT Edge Gateway, Automotive Body and Gateway ECU, Human-Machine Interface (HMI) Panel, BLDC / PMSM Motor Control, USB-Connected Data Acquisition Module, Embedded Connectivity Router, Portable Medical Monitoring Device.
Industrial IoT Edge Gateway
The PIC32MZ0512EFF100T-E/GJX fits industrial IoT edge gateways because its 200 MHz MIPS M-class core delivers 330 DMIPS - enough to run an embedded TCP/IP stack alongside TLS, MQTT-SN, and OPC-UA Pub/Sub without offloading to a separate network processor. The integrated 10/100 Ethernet MAC, dual CAN 2.0B controllers, and 9 UART channels support simultaneous industrial fieldbus (Modbus RTU, CANopen, RS-485) and uplink Ethernet connectivity. The 512 KB dual-panel Flash enables A/B firmware update for unattended remote devices, where roll-back on a failed update is mandatory. AEC-Q100 qualification permits deployment in factory-cabinet environments with extended thermal stress.
Direkomendasikan
Automotive Body and Gateway ECU
The PIC32MZ0512EFF100T-E/GJX is well-suited to automotive body and gateway ECUs because it is AEC-Q100 qualified and pairs a 32-bit 200 MHz core with hardware FPU, enough compute headroom for body-control message routing, LIN/CAN gateway translation, and basic diagnostic services (UDS over CAN). The dual CAN 2.0B modules can be bridged with the Ethernet MAC to form a vehicle-network gateway aggregating sensor data for central compute. 53 GPIO and 6 ADC with 1 MSPS sampling support direct wiring to body actuators and analog sensors. E-grade temperature range covers cabin and underhood near-engine placements.
Direkomendasikan
Human-Machine Interface (HMI) Panel
The PIC32MZ0512EFF100T-E/GJX serves HMI panels well because its Parallel Master Port (PMP) directly drives TFT LCD controllers and external graphics memory while the FPU accelerates vector math for touch-gesture smoothing and animated icons. 512 KB Flash accommodates LVGL or emWin graphics libraries, and 128 KB SRAM holds frame buffers and partial-image assets. Hi-Speed USB OTG allows firmware updates from a USB stick in field service scenarios, and the 12-bit 1 MSPS ADC supports touch-screen and ambient-light sensing without a separate AFE. Industrial-grade variants exist for factory-floor HMIs.
Direkomendasikan
BLDC / PMSM Motor Control
The PIC32MZ0512EFF100T-E/GJX targets BLDC and PMSM motor control because its single-cycle MAC and IEEE 754 FPU deliver the throughput required for field-oriented control (FOC) loops at 20-50 kHz PWM rates while leaving headroom for speed/torque estimators. The 6 ADC with 12-bit 1 MSPS conversion enables simultaneous phase-current sampling without external analog front ends, and the high-resolution PWM peripheral drives the three-phase inverter directly. 512 KB Flash and 128 KB SRAM hold motor parameters and adaptive control tables. AEC-Q100 qualification supports e-mobility applications.
Direkomendasikan
USB-Connected Data Acquisition Module
The PIC32MZ0512EFF100T-E/GJX fits USB-connected data acquisition because its Hi-Speed USB 2.0 OTG controller supports 480 Mbps transfer rates - sufficient for streaming multi-channel 12-bit ADC data to a host PC at tens of kSPS without buffering delays. 128 KB SRAM doubles as a sample FIFO, while 512 KB Flash stores calibration tables and command parsers. 4 SPI and 4 I2C controllers allow daisy-chaining external sensors (accelerometers, thermocouples via ADC) without extra logic. AEC-Q100 grade supports in-vehicle measurement and calibration tools.
Direkomendasikan
Embedded Connectivity Router
The PIC32MZ0512EFF100T-E/GJX fits small-form-factor embedded routers because it integrates Ethernet MAC, USB device, and 9 UARTs into a single chip - sufficient to bridge an LTE modem (over USB), a local Ethernet network, and multiple serial sensor buses without an external host CPU. The 200 MHz MIPS core runs lwIP or a lightweight TCP/IP stack with NAT, while dual-panel Flash supports fail-safe firmware updates critical for remote routers. AEC-Q100 grade covers industrial-cabinet and roadside deployments. The 100-pin TFBGA minimizes PCB area versus QFP alternatives.
Direkomendasikan
Portable Medical Monitoring Device
The PIC32MZ0512EFF100T-E/GJX supports portable medical monitoring where its 200 MHz DSP-extended core executes signal-processing pipelines (FFT, filtering, feature extraction) for ECG, SpO2, or pulse-oximetry signals. The 12-bit 1 MSPS ADC samples analog front-end channels directly, while 128 KB SRAM buffers raw waveforms before feature extraction. The FPU accelerates 32-bit floating-point math libraries used in clinical-grade algorithms. AEC-Q100-style environmental robustness and low 2.3V-3.6V supply support battery-powered designs. Designers should still validate FDA/IEC 62304 compliance for clinical use.
Direkomendasikan
Ringkasan Produk Direkomendasikan
Data referensi engineering untuk PIC32MZ0512EFF100T-E/GJX — pembandingan, panduan desain, dan informasi konformitas.
Panduan Pemilihan
Pembandingan dengan Alternatif
| Parameter Umum | Produk Ini | PIC32MZ0512EFF100-E/GJX | PIC32MZ0512EFF100-I/GJX | PIC32MZ0512EFE100T-E/GJX | PIC32MZ0512EFE100T-I/GJX | PIC32MZ0512EFE100-E/GJX | PIC32MZ0512EFK100T-E/GJX |
|---|---|---|---|---|---|---|---|
| Brand | Microchip Technology | Microchip Technology | Microchip Technology | Microchip Technology | Microchip Technology | Microchip Technology | Microchip Technology |
| Package | 100-pin TFBGA (7x7 mm, GJX) | 100-pin TFBGA (7x7 mm, GJX) | 100-pin TFBGA (7x7 mm, GJX) | 100-pin TFBGA (7x7 mm, GJX) | 100-pin TFBGA (7x7 mm, GJX) | 100-pin TFBGA (7x7 mm, GJX) | 100-pin TFBGA (7x7 mm, GJX) |
| Core Clock | 200 MHz | 200 MHz | 200 MHz | 200 MHz | 200 MHz | 200 MHz | 200 MHz |
| Flash | 512 KB | 512 KB | 512 KB | 512 KB | 512 KB | 512 KB | 512 KB |
| SRAM | 128 KB | 128 KB | 128 KB | 128 KB | 128 KB | 128 KB | 128 KB |
| Crypto Engine | No | No | No | Yes (AES/SHA/RNG) | Yes (AES/SHA/RNG) | Yes (AES/SHA/RNG) | Yes + KGC |
| Temperature Grade | E (Extended) | E (Extended) | I (Industrial -40C to +85C) | E (Extended) | I (Industrial) | E (Extended) | E (Extended) |
| Packaging Form | Tape & Reel | Tray | Tray | Tape & Reel | Tape & Reel | Tray | Tape & Reel |
Diferensiator Kunci
- Dual-panel Flash for fail-safe live firmware update (vsPIC32MZ0512EFF100-E/GJX (tray variant))
- Extended (E) temperature grade (vsPIC32MZ0512EFF100-I/GJX (industrial grade))
- No Crypto engine for cost-optimized designs (vsPIC32MZ0512EFE100T-E/GJX (with Crypto))
- 512 KB Flash for compact firmware (vsPIC32MZ1024EFG100T-E/GJX (1024 KB))
Catatan Desain
The 100-ball TFBGA (7x7 mm) package has 0.65 mm ball pitch and requires NSMD (non-solder mask defined) pads on the PCB. Use micro-via fan-out (0.2 mm via-in-pad optional) and a 4-layer stackup with continuous ground plane beneath the BGA for signal integrity and thermal dissipation. According to Microchip package drawing guidance, a 0.3 mm solder mask opening with 0.45 mm copper pad yields a reliable BGA joint. Avoid placing tall components under the BGA footprint on the opposite side, as flex during assembly can crack the joints.
Place 100 nF X7R decoupling capacitors as close as possible to every VDD pin (typically 7-9 VDD balls distributed across the package). Add 4.7 uF bulk ceramic capacitors near the supply pins. The PIC32MZ EF core runs at 200 MHz and can produce high di/dt transients - a 4-layer PCB with dedicated power and ground planes reduces supply bounce. Estimated: at full 200 MHz core + peripherals, peak current draw can exceed 100 mA instantaneous; size the regulator accordingly.
Although the 100-ball TFBGA has limited heat-dissipation area (no exposed pad in this package variant), the PIC32MZ0512EFF100T-E/GJX typical active power is under 200 mW at 200 MHz, so passive cooling is normally sufficient. For continuous full-load operation in elevated ambient temperatures (>70C), provide thermal relief via internal power planes stitched through the BGA. Verify junction temperature against the E-grade ambient ceiling using the Microchip thermal model.
The integrated Hi-Speed USB 2.0 OTG requires matched 90-ohm differential routing on D+/D- with the trace length matched within 150 mil. Place the USB PHY termination components within 4 mm of the USB connector. For Ethernet RMII/MII, route the 50 MHz RMII clock with controlled impedance and length-match to the PHY. For CAN bus, use twisted-pair cabling with 120-ohm termination at both ends; the MCU's CAN TX/RX pins should connect through an external CAN transceiver.
Do not leave unused VDD pins floating - tie every VDD ball to 3.3V and every VSS ball to ground to prevent internal latch-up. The PIC32MZ EF ICSP programming pins (PGECx/PGEDx) must be accessible on the PCB for in-system programming; leaving them unconnected prevents field firmware updates. Ensure the RTCC oscillator (SOSC) is configured if the real-time clock calendar is needed, otherwise tie SOSC pins to ground or leave unconnected per datasheet guidance.
Informasi Konformitas
AEC-Q100 qualified for automotive (per datasheets.com listing); RoHS compliant; lead-free and halogen-free packaging per Microchip product family datasheet. The -E temperature grade extends beyond industrial -40C to +85C.
