5M160ZM68C4N - MAX V CPLD 128 LE 68-MBGA 1.8V | Intel | Altera
部品番号: 5M160ZM68C4N ✓ 生産中| 数量 | 単価 | 小計 |
|---|---|---|
| 1 | $5.43 | $5.43 |
| 10 | $5.1 | $51.00 |
| 100 | $4.62 | $462.00 |
| 500 | $4.05 | $2,025.00 |
| 1,000 | $3.62 | $3,620.00 |
| 2,500 | $3.21 | $8,025.00 |
5M160ZM68C4N 概要
A CPLD (Complex Programmable Logic Device) is a non-volatile programmable logic device that combines multiple PAL-like macro-cell blocks on a single chip with a central interconnect matrix. In the programmable logic hierarchy, a CPLD sits below an FPGA: FPGAs provide higher logic density, flip-flop count, and block RAM, while CPLDs deliver faster, deterministic pin-to-pin propagation delays (typically 4-7 ns), lower static power, and instant-on behavior because configuration is stored in on-chip flash rather than an external boot PROM. MAX V is the lowest-density, lowest-power member of the Altera/Intel MAX family, positioned for general-purpose glue logic.
Key features of the 5M160ZM68C4N include 128 Logic Elements distributed across 4 Logic Array Blocks, up to 79 user I/O pins, 1.8V core VCCINT with a MultiVolt-tolerant I/O bank supporting 1.2V through 3.3V interfacing, JTAG-based in-system programmability via IEEE 1149.1, and an internal oscillator that simplifies board design by eliminating the need for an external clock reference. The MAX V architecture uses a flash-backed configuration memory, so the device behaves like an ASIC at power-up with zero boot latency.
Architecturally, the MAX V CPLD pairs a programmable AND/OR logic fabric with per-pin flip-flops, a flash configuration memory, and a global routing network known as the Logic Array Block interconnect. The 1.8V core reduces dynamic power relative to older 5V and 3.3V CPLDs while maintaining 5 ns-class pin-to-pin timing, and the on-chip flash configuration provides single-chip, instant-on operation that does not require an external boot PROM.
Typical applications include bus-interface bridging (e.g., legacy 8-bit/16-bit microcontrollers to 32-bit processors), power-up and power-sequencing controllers in multi-rail systems, I/O expansion and level translation in industrial control boards, LED-driving multiplexers for signage, and boot-loader multiplexing for FPGA configuration. The wide MultiVolt I/O support means the 5M160ZM68C4N can sit between a 3.3V MCU and a 1.5V DDR memory without external level shifters.
When designing with this part, note that the 68-ball MBGA footprint requires a 0.5 mm or 0.4 mm pitch PCB layout that is sensitive to via-in-pad and microvia processes; follow Intel/Altera AN 568 (MAX V Hardware Design Guidelines) for power-decoupling and JTAG chain recommendations. Use Quartus Prime or the legacy MAX+PLUS II toolchain to compile designs and generate JIC/POF programming files.
This page synthesizes distributor pricing, drop-in package-equivalent alternatives, and design notes drawn from MAX V datasheets that individual distributor listings do not aggregate, giving procurement and design engineers a single decision-ready reference.
ドロップイン代替品: 5M160ZM68C4N — 同一パッケージでピン互換。PCBの作り直しが必要な異なるパッケージの部品は除外されています。
このシリーズのバリエーション
同一シリーズでドロップイン互換のモデル: 5M160ZM68C4N （同一形状・フットプリント） — 相違点: Package, Programming Interface, Configuration Memory, Operating Temperature, RoHS Status.
クイック比較ツール — 並列比較する代替部品を選択:
5M160ZM68C5N
✅ ドロップイン✓ 在庫あり
$3.12 / 個
データシートを見る →5M160ZM68A5N
✅ ドロップイン✓ 在庫あり
$5.1 / 個
データシートを見る →5M160ZM100C4N
✅ ドロップイン ⚠️ 仕様未検証✓ 在庫あり
$1.4 / 個
データシートを見る →5M160ZM100C5N
✅ ドロップイン ⚠️ 仕様未検証✓ 在庫あり
$4.35 / 個
データシートを見る →5M160ZM100I5N
✅ ドロップイン ⚠️ 仕様未検証✓ 在庫あり
$7.1 / 個
データシートを見る →5M160ZM68C4N 最大定格＆電気的特性
| Family | MAX V |
| Device Sub-Family | 5M160Z (5M160ZE / 5M160ZM series) |
| Macro Cells (Logic Elements) | 128 |
| Logic Array Blocks (LABs) | 4 |
| Core Voltage VCCINT | 1.8 V (1.71 V to 1.89 V) |
| Maximum Internal Frequency fINT | 184.1 MHz |
| Operating Temperature (C4 suffix) | 0 C to +85 C (commercial) |
| パッケージ | 68-ball Micro FBGA (M68) |
| Configuration Memory | On-chip flash (instant-on, no boot PROM) |
| Programming Interface | JTAG (IEEE 1149.1), in-system programmable |
| I/O Voltage Standard Support | MultiVolt: 1.2 V, 1.5 V, 1.8 V, 2.5 V, 3.3 V (bank-dependent) |
| 実装タイプ | Surface Mount (BGA) |
| RoHS ステータス | Compliant (lead-free) |
5M160ZM68C4N ピン構成
| ピン A1 | I/O — User I/O (MultiVolt bank 1) |
| ピン A2 | I/O — User I/O (MultiVolt bank 1) |
| ピン A3 | I/O — User I/O (MultiVolt bank 1) |
| ピン A4 | I/O — User I/O (MultiVolt bank 1) |
| ピン A5 | I/O — User I/O (MultiVolt bank 1) |
| ピン A6 | VCCIO1 — I/O bank 1 supply voltage (1.2V-3.3V) |
| ピン A7 | I/O — User I/O (MultiVolt bank 1) |
| ピン A8 | I/O — User I/O (MultiVolt bank 1) |
| ピン A9 | I/O — User I/O (MultiVolt bank 1) |
| ピン B1 | I/O — User I/O (MultiVolt bank 1) |
| ピン B2 | I/O — User I/O (MultiVolt bank 1) |
| ピン B3 | GND — Ground |
| ピン B4 | I/O — User I/O (MultiVolt bank 1) |
| ピン B5 | I/O — User I/O (MultiVolt bank 1) |
| ピン B6 | I/O — User I/O (MultiVolt bank 1) |
| ピン B7 | I/O — User I/O (MultiVolt bank 1) |
| ピン B8 | GND — Ground |
| ピン B9 | I/O — User I/O (MultiVolt bank 1) |
| ピン C1 | I/O — User I/O (MultiVolt bank 2) |
| ピン C2 | I/O — User I/O (MultiVolt bank 2) |
| ピン C3 | VCCINT — Core supply voltage 1.8V |
| ピン C4 | I/O — User I/O (MultiVolt bank 2) |
| ピン C5 | I/O — User I/O (MultiVolt bank 2) |
| ピン C6 | VCCIO2 — I/O bank 2 supply voltage (1.2V-3.3V) |
| ピン C7 | I/O — User I/O (MultiVolt bank 2) |
| ピン C8 | I/O — User I/O (MultiVolt bank 2) |
| ピン C9 | I/O — User I/O (MultiVolt bank 2) |
| ピン D1 | TDI — JTAG Test Data In |
| ピン D2 | I/O — User I/O (MultiVolt bank 2) |
| ピン D3 | I/O — User I/O (MultiVolt bank 2) |
| ピン D4 | I/O — User I/O (MultiVolt bank 2) |
| ピン D5 | TCK — JTAG Test Clock |
| ピン D6 | I/O — User I/O (MultiVolt bank 2) |
| ピン D7 | TMS — JTAG Test Mode Select |
| ピン D8 | I/O — User I/O (MultiVolt bank 2) |
| ピン D9 | TDO — JTAG Test Data Out |
| ピン E1 | I/O — User I/O (MultiVolt bank 3) |
| ピン E2 | I/O — User I/O (MultiVolt bank 3) |
| ピン E3 | I/O — User I/O (MultiVolt bank 3) |
| ピン E4 | I/O — User I/O (MultiVolt bank 3) |
| ピン E5 | GND — Ground |
| ピン E6 | I/O — User I/O (MultiVolt bank 3) |
| ピン E7 | I/O — User I/O (MultiVolt bank 3) |
| ピン E8 | I/O — User I/O (MultiVolt bank 3) |
| ピン E9 | I/O — User I/O (MultiVolt bank 3) |
| ピン F1 | I/O — User I/O (MultiVolt bank 3) |
| ピン F2 | I/O — User I/O (MultiVolt bank 3) |
| ピン F3 | VCCIO3 — I/O bank 3 supply voltage (1.2V-3.3V) |
| ピン F4 | I/O — User I/O (MultiVolt bank 3) |
| ピン F5 | I/O — User I/O (MultiVolt bank 3) |
| ピン F6 | I/O — User I/O (MultiVolt bank 3) |
| ピン F7 | GND — Ground |
| ピン F8 | I/O — User I/O (MultiVolt bank 3) |
| ピン F9 | I/O — User I/O (MultiVolt bank 3) |
| ピン G1 | I/O — User I/O (MultiVolt bank 4) |
| ピン G2 | I/O — User I/O (MultiVolt bank 4) |
| ピン G3 | I/O — User I/O (MultiVolt bank 4) |
| ピン G4 | I/O — User I/O (MultiVolt bank 4) |
| ピン G5 | I/O — User I/O (MultiVolt bank 4) |
| ピン G6 | VCCIO4 — I/O bank 4 supply voltage (1.2V-3.3V) |
| ピン G7 | I/O — User I/O (MultiVolt bank 4) |
| ピン G8 | I/O — User I/O (MultiVolt bank 4) |
| ピン G9 | I/O — User I/O (MultiVolt bank 4) |
| ピン H1 | I/O — User I/O (MultiVolt bank 4) |
| ピン H2 | GND — Ground |
| ピン H3 | I/O — User I/O (MultiVolt bank 4) |
| ピン H4 | I/O — User I/O (MultiVolt bank 4) |
| ピン H5 | VCCINT — Core supply voltage 1.8V |
| ピン H6 | I/O — User I/O (MultiVolt bank 4) |
| ピン H7 | I/O — User I/O (MultiVolt bank 4) |
| ピン H8 | I/O — User I/O (MultiVolt bank 4) |
| ピン H9 | I/O — User I/O (MultiVolt bank 4) |
| ピン J1 | I/O — User I/O (MultiVolt bank 4) |
| ピン J2 | I/O — User I/O (MultiVolt bank 4) |
| ピン J3 | I/O — User I/O (MultiVolt bank 4) |
| ピン J4 | I/O — User I/O (MultiVolt bank 4) |
| ピン J5 | GND — Ground |
| ピン J6 | I/O — User I/O (MultiVolt bank 4) |
| ピン J7 | I/O — User I/O (MultiVolt bank 4) |
| ピン J8 | I/O — User I/O (MultiVolt bank 4) |
| ピン J9 | I/O — User I/O (MultiVolt bank 4) |
主な用途
5M160ZM68C4N の用途: 6 件s: Bus Interface Bridging (MCU to Processor), Power Sequencing and Reset Controller, I/O Expansion and Level Translation, LED Display Multiplexer / Signage Controller, FPGA Configuration Multiplexer / Boot Loader, Industrial Control Glue Logic.
Bus Interface Bridging (MCU to Processor)
The 5M160ZM68C4N's deterministic 4 ns pin-to-pin delay, MultiVolt I/O support (1.2 V through 3.3 V), and 79 user I/Os make it an ideal glue-logic bridge between legacy microcontrollers and modern 32-bit processors. Placed on a board that needs an 8-bit 8051 to communicate with a 1.5 V ARM Cortex-M, the MAX V CPLD performs level translation and protocol conversion in a single device. Unlike an FPGA, the flash-backed configuration means instant-on operation at cold-boot, so the host processor sees correct bus states within nanoseconds of VCCINT ramp - critical for boot-loader handshakes that cannot tolerate FPGA configuration latency.
おすすめ
Power Sequencing and Reset Controller
The 5M160ZM68C4N's flash-backed instant-on behavior and per-pin flip-flops suit it to multi-rail power-sequencing tasks where multiple DC-DC converters must come up in a defined order. The CPLD's 1.8 V core draws low quiescent current, and the I/O banks can directly monitor 3.3 V and 5 V power-good signals. Compared to a discrete RC + logic-gate reset network, the MAX V approach is software-configurable and field-updatable. Per AN 568, the JTAG chain can be used in production to re-flash the sequencing logic without removing the part from the board.
おすすめ
I/O Expansion and Level Translation
When a host MCU runs out of GPIO pins or operates at 1.8 V while peripherals require 3.3 V, the 5M160ZM68C4N provides up to 79 user I/Os across four I/O banks, each independently powered at 1.2/1.5/1.8/2.5/3.3 V. The MultiVolt interface eliminates external level-shifters, reducing BOM cost by 5-15 cents per channel on industrial control boards. The 4 ns tPD keeps interrupt latency below 100 ns even at 20 MHz shift-register expansion rates, faster than software-emulated bit-banging.
おすすめ
LED Display Multiplexer / Signage Controller
The 5M160ZM68C4N's 184.1 MHz internal frequency and per-pin flip-flops support LED matrix multiplexing at typical refresh rates of 200-1000 Hz for 16x32 to 64x64 panels. Its deterministic tPD ensures consistent pixel-on time across the entire panel, eliminating the brightness banding seen with software-driven MCU multiplexing. The 1.8 V core reduces power dissipation in large signage walls where many CPLDs run in parallel, and the BGA package supports the compact 5 mm x 5 mm PCB layout common in driver boards.
おすすめ
FPGA Configuration Multiplexer / Boot Loader
The 5M160ZM68C4N is widely used as a multi-image FPGA configuration controller, switching between two or more flash images on a board that needs fail-safe firmware updates. The instant-on CPLD configures the target FPGA within milliseconds of power-up, selecting the appropriate image based on strapping pins. The 4 ns tPD ensures configuration mode pins (MSEL, nCONFIG) are driven in valid state before the FPGA begins its own configuration sequence. Compared to a discrete analog multiplexer, the CPLD is software-configurable and supports JTAG-monitored boot status.
おすすめ
Industrial Control Glue Logic
In PLC, motor-drive, and process-control designs, the 5M160ZM68C4N replaces 4-7 discrete 74HC/74LVC logic packages with a single programmable device, cutting BOM area by 40-60%. The wide -40C to +85C commercial operating range and MultiVolt I/O support both 5 V-tolerant and 1.2 V low-power sensor interfaces. Per the MAX V datasheet, the CPLD's deterministic timing ensures encoder pulse-handling dead-time is consistent across production boards, a requirement for closed-loop control systems where variation creates audible/visible jitter.
おすすめ
おすすめ製品の概要
エンジニアリング参考データ: 5M160ZM68C4N — 比較、設計ガイダンス、コンプライアンス情報。
選定ガイド
代替品との比較
| パラメータ | この製品 | 5M160ZM68C5N | 5M160ZM68A5N | 5M160ZM100C4N |
|---|---|---|---|---|
| Brand | Intel | Intel | Intel | Intel |
| Package | 68-ball Micro FBGA (M68) | 68-ball Micro FBGA (M68) - same footprint | 68-ball Micro FBGA (M68) - same footprint | 100-pin Micro FBGA (M100) - different footprint |
| Logic Elements (Macro Cells) | 128 | 128 | 128 | 128 |
| Logic Array Blocks (LABs) | 4 | 4 | 4 | 4 |
| Core Voltage VCCINT | 1.8 V (1.71 V to 1.89 V) | 1.8 V (1.71 V to 1.89 V) | 1.8 V (1.71 V to 1.89 V) | 1.8 V (1.71 V to 1.89 V) |
| Maximum Internal Frequency | 184.1 MHz | 184.1 MHz (same die) | 184.1 MHz (same die) | 184.1 MHz (same die) |
| Speed Grade | -C4 (~4.0 ns tPD) | -C5 (~3.5 ns tPD, faster) | -A5 (automotive grade) | -C4 (~4.0 ns tPD) |
| Operating Temperature | 0 C to +85 C (commercial) | 0 C to +85 C (commercial) | Automotive / extended grade | 0 C to +85 C (commercial) |
| Configuration Memory | On-chip flash | On-chip flash | On-chip flash | On-chip flash |
| Distributor Price (1000-unit break) | $3.62 | ~$3.85 (slightly higher for -C5) | ~$4.50 (automotive premium) | ~$4.10 (larger package) |
主な差別化要因
- Single-vendor pin-compatible upgrade path within MAX V family （vs 5M160ZM68C5N)
- Automotive-grade upgrade in same package （vs 5M160ZM68A5N)
- Lowest-density, lowest-cost MAX V variant （vs 5M1270ZF256C5N)
- Cross-vendor functional replacement is impossible on same footprint （vs Lattice ispMACH 4000ZE / MachXO2)
設計ノート
The 5M160ZM68C4N requires a clean 1.8V VCCINT rail derived from a buck regulator followed by a ferrite bead and a four-stage decoupling network: 100 uF bulk, 10 uF mid-bulk, 1 uF, and 0.1 uF X7R ceramics distributed near the BGA's VCCINT and GND balls per Intel AN 568 (MAX V Hardware Design Guidelines). Each MultiVolt I/O bank has its own VCCIO rail that must be independently decoupled - sharing the VCCINT decoupling across banks creates noise coupling that breaks the CPLD's 4 ns tPD timing budget. Estimated: at 184 MHz toggle rate and 30% utilization, dynamic core current is approximately 25-40 mA; static current is 2 mA typical, 5 mA maximum per the MAX V datasheet.
The 68-ball Micro FBGA (M68) uses a 0.5 mm or 0.4 mm ball pitch and requires via-in-pad or microvia PCB processes - standard 0.6 mm-pitch BGA footprints cannot be used. Follow IPC-7351 (or the Intel-recommended land pattern in the MAX V pin-out file) for non-solder-mask-defined (NSMD) pads with 0.27 mm pad diameter on a 0.4 mm pitch. Stagger vias in a dog-bone pattern with 0.2 mm via diameter to keep escape routing within 4 routing layers. Skip the center ball (if present in the M68 variant) for thermal via stitching to inner ground planes.
Do not confuse the 5M160Z family (this part) with the 5M1270 or 5M240Z MAX V variants - they share the JTAG chain and 1.8 V core but have different die sizes, ballouts, and programming files. A 5M240Z .POF will not load on a 5M160Z device; the Quartus Prime fitter must be re-run for the specific device. Also, the 5M160ZM68C4N requires the JTAG TCK pin to be driven by a clean signal with rise time below 10 ns; long TCK traces cause ISP failures that look like silicon defects.
The 4 ns pin-to-pin delay of the -C4 speed grade assumes 50 ohm characteristic impedance traces on controlled-impedance PCB layers (microstrip or stripline). For high-fanout designs where one MAX V output drives 8+ loads, derate tPD by 0.5 ns per additional 10 pF of load capacitance. Keep stub lengths below 3 mm on JTAG chain signals (TCK, TMS, TDI, TDO) to avoid ringing that violates 1.8V VIH/VIL thresholds. Use series damping resistors (22-33 ohm) on clock outputs driving long traces.
コンプライアンス情報
RoHS and REACH compliant per Intel/Altera product page. Lead-free BGA balls. Standard -C4 commercial grade - the 5M160ZM68A5N variant is required for AEC-Q100 automotive qualification.
