DSPIC33EP16GS504T-E/PT - 16-bit DSC, 16KB Flash, TQFP-44 | Microchip
部品番号: DSPIC33EP16GS504T-E/PT ✓ 生産中| 数量 | 単価 | 小計 |
|---|---|---|
| 1 | $0 | $0.00 |
| 10 | $0 | $0.00 |
| 100 | $0 | $0.00 |
| 500 | $0 | $0.00 |
| 1,000 | $0 | $0.00 |
DSPIC33EP16GS504T-E/PT 概要
A digital signal controller combines the computational throughput of a digital signal processor with the peripheral integration and control-oriented architecture of a microcontroller. Within the power-management hierarchy, the DSC sits above a general-purpose MCU for switch-mode power conversion tasks, providing deterministic interrupt latency and dedicated PWM hardware that a standard microcontroller cannot match. The dsPIC33EP GS family is Microchip's SMPS-focused DSC line, purpose-built for digital power supplies.
Key features include 16-bit modified Harvard architecture execution, a high-speed PWM module with complementary outputs, dead-time insertion and fault protection tailored for switched-mode power supplies, a 10-bit high-speed ADC for current- and voltage-loop feedback, and standard serial connectivity. The device is qualified to AEC-Q100 for automotive use and supports Functional Safety (FuSa) development, as listed by distributors.
Technically, the GS504 core delivers 16-bit DSP instruction support with hardware multiply-accumulate, enabling Proportional-Integral compensation loops in software at switching frequencies well above 100 kHz. In-Circuit Serial Programming (ICSP) via MPLAB SNAP allows field programming using two device I/O pins and the reset line.
Typical applications include interleaved power factor correction (Microchip's 350W interleaved PFC reference design targets this family), LLC and flyback converters, digital AC-DC power supplies, automotive power modules, and industrial motor-control front ends.
Design consideration: budget the 2KB SRAM carefully when running multiple control loops with ADC buffering; the 16KB FLASH constrains complex compensation algorithms, so consider 32GS/64GS variants if code growth is expected.
This page synthesizes distributor stock and pricing signals, drop-in same-family alternatives, and practical design notes not consolidated in the manufacturer datasheet.
ドロップイン代替品: DSPIC33EP16GS504T-E/PT — 同一パッケージでピン互換。PCBの作り直しが必要な異なるパッケージの部品は除外されています。
このシリーズのバリエーション
同一シリーズでドロップイン互換のモデル: DSPIC33EP16GS504T-E/PT （同一形状・フットプリント） — 相違点: Core Architecture, Operating Temperature, Package, Analog Peripherals, Communication Interfaces.
クイック比較ツール — 並列比較する代替部品を選択:
DSPIC33EP16GS504-I/PT
✅ ドロップイン✓ 在庫あり
価格はお問い合わせください
データシートを見る →DSPIC33EP32GS504-E/PT
✅ ドロップイン ⚠️ 仕様未検証📋 参考代替品（カタログ未掲載）
DSPIC33EP64GS504-E/PT
✅ ドロップイン ⚠️ 仕様未検証✓ 在庫あり
$5.61 / 個
データシートを見る →DSPIC33EP16GS504T-E/PT 最大定格＆電気的特性
| Core Architecture | 16-bit dsPIC33EP DSC |
| Flash Program Memory | 16 KB (16K x 8) |
| SRAM | 2 KB |
| Max Core Speed | 60 MIPS (listed up to 70 MIPS by Mouser) |
| Operating Voltage | 3.0 V to 3.6 V (3.3 V nominal) |
| パッケージ | 44-TQFP (10 x 10 mm, 0.8 mm pitch) |
| 動作温度 | -40C to +125C (E, extended) |
| Qualification | AEC-Q100, Automotive, Functional Safety (FuSa) |
| 実装タイプ | Surface Mount |
| Packaging Suffix | /T (Tape & Reel) |
| PWM | High-speed SMPS PWM module |
| Communication Interfaces | UART, SPI, I2C |
| Programming Interface | ICSP (2-wire) via MPLAB SNAP |
| Family Series | dsPIC33EP 33EP (GS, SMPS-oriented) |
| RoHS ステータス | Compliant |
DSPIC33EP16GS504T-E/PT ピン構成
| ピン 1 | MCLR — Master clear reset / programming voltage input |
| ピン 2 | AN0/VREF+/RB0 — Analog input 0 / ADC positive reference / port B |
| ピン 3 | AN1/VREF-/RB1 — Analog input 1 / ADC negative reference / port B |
| ピン 4 | AN2/PGD/RB2 — Analog input 2 / In-Circuit Debug data / port B |
| ピン 5 | AN3/PGC/RB3 — Analog input 3 / In-Circuit Debug clock / port B |
| ピン 6 | AN4/RB4 — Analog input 4 / port B |
| ピン 7 | AN5/RB5 — Analog input 5 / port B |
| ピン 8 | VSS — Ground reference |
| ピン 9 | OSC1/CLKI — Crystal oscillator input / external clock input |
| ピン 10 | OSC2/CLKO — Crystal oscillator output / clock output |
| ピン 11 | VDD — Positive supply (3.0V-3.6V) |
| ピン 12 | RB6 — General purpose I/O / peripheral pin (PPS) |
| ピン 13 | RB7 — General purpose I/O / peripheral pin (PPS) |
| ピン 14 | RB8 — General purpose I/O / peripheral pin (PPS) |
| ピン 15 | RB9 — General purpose I/O / peripheral pin (PPS) |
| ピン 16 | VDD — Positive supply (3.0V-3.6V) |
| ピン 17 | VSS — Ground reference |
| ピン 18 | RB10 — General purpose I/O / peripheral pin (PPS) |
| ピン 19 | RB11 — General purpose I/O / peripheral pin (PPS) |
| ピン 20 | RB12 — General purpose I/O / peripheral pin (PPS) |
| ピン 21 | RB13 — General purpose I/O / peripheral pin (PPS) |
| ピン 22 | RB14 — General purpose I/O / peripheral pin (PPS) |
| ピン 23 | RB15 — General purpose I/O / peripheral pin (PPS) |
| ピン 24 | VSS — Ground reference |
| ピン 25 | VDD — Positive supply (3.0V-3.6V) |
| ピン 26 | RC0 — General purpose I/O / peripheral pin (PPS) |
| ピン 27 | RC1 — General purpose I/O / peripheral pin (PPS) |
| ピン 28 | RC2 — General purpose I/O / peripheral pin (PPS) |
| ピン 29 | RC3 — General purpose I/O / peripheral pin (PPS) |
| ピン 30 | RC4 — General purpose I/O / peripheral pin (PPS) |
| ピン 31 | RC5 — General purpose I/O / peripheral pin (PPS) |
| ピン 32 | RC6 — General purpose I/O / peripheral pin (PPS) |
| ピン 33 | RC7 — General purpose I/O / peripheral pin (PPS) |
| ピン 34 | RC8 — General purpose I/O / peripheral pin (PPS) |
| ピン 35 | RC9 — General purpose I/O / peripheral pin (PPS) |
| ピン 36 | PWM1L1 — High-speed PWM 1 low-side output 1 |
| ピン 37 | VDD — Positive supply (3.0V-3.6V) |
| ピン 38 | VSS — Ground reference |
| ピン 39 | PWM1H1 — High-speed PWM 1 high-side output 1 |
| ピン 40 | PWM1L2 — High-speed PWM 1 low-side output 2 |
| ピン 41 | PWM1H2 — High-speed PWM 1 high-side output 2 |
| ピン 42 | PWM1L3 — High-speed PWM 1 low-side output 3 |
| ピン 43 | PWM1H3 — High-speed PWM 1 high-side output 3 |
| ピン 44 | FLTA — PWM fault input A |
主な用途
DSPIC33EP16GS504T-E/PT の用途: 6 件s: Interleaved Power Factor Correction, Digital AC-DC Power Supplies, Automotive Power Modules, Industrial Motor Control Front Ends, LED Driver Ballasts and Lighting Power, Embedded Digital Power Development Platforms.
Interleaved Power Factor Correction
Microchip's Interleaved PFC reference design targets the dsPIC33EP GS family and delivers up to 350W from a universal AC input range. The DSPIC33EP16GS504T-E/PT fits this role because its high-speed SMPS PWM module generates phase-shifted complementary outputs with hardware dead-time insertion, while the fast ADC samples inductor current and bus voltage for average-current-mode control at switching frequencies beyond 100 kHz. The 16-bit DSP core executes PI compensation loops with multiply-accumulate instructions deterministically, avoiding the jitter of software-timed control. The -40C to +125C extended grade and AEC-Q100 qualification allow deployment in automotive and industrial front ends. Two interleaved boost legs share one 44-pin TQFP controller, reducing BOM count versus analog-control solutions.
おすすめ
Digital AC-DC Power Supplies
Flyback, forward, and LLC AC-DC converters benefit from the DSPIC33EP16GS504T-E/PT's combination of a 60-70 MIPS DSP core and dedicated SMPS PWM hardware. The controller closes voltage and current loops digitally, enabling adaptive burst mode, proprietary startup sequencing, and precise output regulation that analog controllers cannot reconfigure in firmware. The 2KB SRAM accommodates ADC result buffering and loop state variables for dual-loop control, while ICSP programming via MPLAB SNAP lets manufacturers update firmware in production. The 3.0V-3.6V supply range simplifies bias generation from an auxiliary winding. Extended -40C to +125C operation suits sealed adapters and industrial supplies where ambient temperatures inside enclosures exceed +85C regularly.
おすすめ
Automotive Power Modules
With AEC-Q100 qualification, Functional Safety (FuSa) support, and the extended E temperature grade, the DSPIC33EP16GS504T-E/PT is positioned for automotive DC-DC converters, LED headlamp drivers, and 48V mild-hybrid subsystems. The high-speed PWM provides cycle-by-cycle current limiting with hardware fault shutdown, a requirement for protecting automotive power stages during load-dump or short-circuit events. The 10x10 mm TQFP withstands the vibration and thermal cycling of under-hood electronics better than larger packages due to compliant lead frames. Designers should implement Microchip's safety libraries and follow the family's functional-safety documentation to satisfy ISO 26262-aligned development flows applicable to the end system.
おすすめ
Industrial Motor Control Front Ends
The DSPIC33EP16GS504T-E/PT serves as the power-conversion controller in industrial drives, handling PFC or DC bus stages that feed Microchip's motor-control DSCs. Its 16-bit DSP core runs current-loop compensation at high bandwidth while the SMPS PWM drives half-bridge stages with hardware dead time, keeping switching losses predictable. The 44-pin count leaves sufficient GPIO for gate-driver enable sequencing, fault aggregation, and UART or CAN-adjacent serial links for supervisory communication. In factory environments with ambient temperatures up to +70C inside cabinets, the +125C junction capability provides wide derating margin. Firmware-updatable control parameters enable one PCB platform to serve multiple motor power ratings through configuration.
おすすめ
LED Driver Ballasts and Lighting Power
High-power LED luminaires and automotive lighting require constant-current converters with dimming control, a task matched to the DSPIC33EP16GS504T-E/PT's PWM resolution and ADC sampling speed. The SMPS PWM module drives buck or boost LED stages while a second PWM channel generates dimming waveforms free of visible flicker at frequencies above the camera-audibility thresholds. Digital control enables thermal foldback: the ADC reads an NTC sensor and firmware scales output current as temperature rises, extending LED lifetime. The extended -40C to +125C rating covers sealed outdoor luminaires exposed to solar heating, and AEC-Q100 qualification supports automotive exterior lighting modules where quality audits demand automotive-qualified silicon.
おすすめ
Embedded Digital Power Development Platforms
The DSPIC33EP16GS504T-E/PT is an excellent learning and prototyping vehicle for digital power engineering because Microchip publishes reference designs, SMPS libraries, and MPLAB X toolchain support for the GS family. Engineers can iterate compensation firmware in minutes using ICSP in-circuit reprogramming through MPLAB SNAP, which needs only two I/O pins plus reset - no socketed parts or external programmers beyond the low-cost SNAP tool. The 44-pin TQFP is hand-solderable for prototype boards and universally available on assembly lines. Its parameter set (16KB FLASH, 2KB SRAM) also disciplines code size early, with a seamless upgrade path to the pin-compatible 32GS504 and 64GS504 when control algorithms grow more complex.
おすすめ
おすすめ製品の概要
エンジニアリング参考データ: DSPIC33EP16GS504T-E/PT — 比較、設計ガイダンス、コンプライアンス情報。
選定ガイド
代替品との比較
| パラメータ | この製品 | DSPIC33EP16GS504-I/PT | DSPIC33EP32GS504-E/PT | DSPIC33EP64GS504-E/PT |
|---|---|---|---|---|
| Brand | Microchip Technology | Microchip Technology | Microchip Technology | Microchip Technology |
| Package | 44-TQFP (10x10 mm) | 44-TQFP (10x10 mm) - same | 44-TQFP (10x10 mm) - same | 44-TQFP (10x10 mm) - same |
| Flash Memory | 16 KB | 16 KB | 32 KB | 64 KB |
| Core Speed | 60-70 MIPS | 60-70 MIPS | 60-70 MIPS | 60-70 MIPS |
| Operating Temperature | -40C to +125C (E) | -40C to +85C (I) | -40C to +125C (E) | -40C to +125C (E) |
| Operating Voltage | 3.0 V - 3.6 V | 3.0 V - 3.6 V | 3.0 V - 3.6 V | 3.0 V - 3.6 V |
| PCB Rework Required | - | None - same footprint | None - same footprint | None - same footprint |
主な差別化要因
- Extended temperature range for automotive and sealed power supplies （vs DSPIC33EP16GS504-I/PT)
- Upgrade headroom without PCB rework （vs DSPIC33EP32GS504-E/PT)
- SMPS-optimized peripheral set vs general-purpose MCUs （vs PIC16LF1787-E/ML (site catalog MCU))
設計ノート
Place a 100nF ceramic capacitor at every VDD/VSS pin pair (pins 11/8, 16/17, 25/24, 37/38 on the 44-TQFP) with traces under 5 mm, plus one 4.7uF-10uF bulk capacitor near the package. The 3.0V-3.6V rail must stay within range during PWM transients; in digital power designs the controller rail is often derived from an auxiliary flyback winding, so verify minimum bias voltage at light load before the main converter starts. Estimated: four decoupling capacitors plus local bulk keeps high-frequency supply impedance low enough for 60-70 MIPS core operation.
Use a solid ground plane on layer 2 beneath the 10x10 mm TQFP and return each VSS pin directly with multiple vias. Keep the PWM gate-drive traces (PWM1H/L outputs) short and away from ADC input traces to prevent switching noise coupling into current-sense feedback; the SMPS PWM module's dead-time depends on clean edge timing. Land pattern per Microchip family datasheet: 0.8 mm pitch, 10x10 mm body. Expose no thermal pad - the PT TQFP dissipates heat through the leads, so provide adequate copper on outer layers.
Watch the memory budget: 16KB FLASH and 2KB SRAM fill quickly with floating-point compensation code; use fixed-point math and the DSP multiply-accumulate instructions, and profile code size before committing. The /T tape-and-reel suffix means parts arrive in reels for pick-and-place - hand soldering from reels requires cut-tape handling. Also confirm the temperature grade: the -I/PT variant is limited to +85C ambient-class operation, and substituting it into an E-grade design silently reduces thermal margin. Verify all pin assignments against the latest Microchip datasheet before layout freeze.
コンプライアンス情報
RoHS compliance and lead-free TQFP terminations per JLCPCB and distributor listings. AEC-Q100 automotive qualification and Functional Safety (FuSa) support per Hotenda and Chip In Stock product data. REACH, halogen-free, and conflict-minerals statuses not stated in provided data.
