IRF7205TRPBF - P-Ch -30V -4.6A 70mΩ SO-8 MOSFET | Infineon
部品番号: IRF7205TRPBF ✓ 生産中| 数量 | 単価 | 小計 |
|---|---|---|
| 1 | $0.55 | $0.55 |
| 10 | $0.48 | $4.80 |
| 100 | $0.36 | $36.00 |
| 500 | $0.27 | $135.00 |
| 1,000 | $0.22 | $220.00 |
| 3,000 | $0.18 | $540.00 |
IRF7205TRPBF 概要
A power MOSFET (metal-oxide-semiconductor field-effect transistor) is a voltage-controlled switching device that regulates power flow between drain and source terminals via an insulated gate. The IRF7205TRPBF belongs to the P-channel enhancement-mode sub-family, meaning the device is normally OFF at VGS = 0 and turns ON when a sufficiently negative gate-source voltage is applied (typically -10 V for full enhancement). Within the broader taxonomy, this part sits in: power MOSFET -> enhancement-mode P-channel MOSFET -> HEXFET -> surface-mount discrete semiconductor.
Key differentiating features include an advanced IR MOSFET process technology, ultra-low on-resistance per silicon area, dynamic dv/dt rating, fast switching capability, lead-free plating, and an ultra-low threshold-gate charge of 27 nC (Qg) that minimizes driver losses. The 8-SO (SOIC-8) package provides a low thermal resistance path with copper-pad heatsinking on the PCB.
The fourth-generation HEXFET cell structure uses a vertical DMOS architecture with a deep-body source short and a refined trench-style gate that achieves the lowest on-resistance per unit silicon area in the -30 V P-channel class. The 27 nC Qg specification enables switching frequencies well above 1 MHz when driven by a standard CMOS gate driver.
Typical applications include high-side load switches, DC-DC synchronous-rectifier replacements, battery protection and reverse-polarity blocking in portable equipment, and motor-drive half-bridges in industrial automation. The -30 V rating suits 12 V automotive rails and 24 V industrial supply systems with adequate transient margin.
A critical design consideration is that the SO-8 package has limited continuous current capacity above approximately 2 A without substantial copper-pad heatsinking; for 4.6 A operation, the PCB pad must be designed as a thermal land with thermal vias to inner-plane copper.
This page synthesizes distributor pricing, drop-in alternatives, and practical design notes not found on the manufacturer datasheet alone.
ドロップイン代替品: IRF7205TRPBF — 同一パッケージでピン互換。PCBの作り直しが必要な異なるパッケージの部品は除外されています。
このシリーズのバリエーション
同一シリーズでドロップイン互換のモデル: IRF7205TRPBF （同一形状・フットプリント） — 相違点: Technology, Operating Temperature Range, Package, Lead-Free / RoHS, Mounting Type.
クイック比較ツール — 並列比較する代替部品を選択:
IRF7205PBF
✅ ドロップイン✓ 在庫あり
$0.47 / 個
データシートを見る →IRF7207TRPBF
✅ ドロップイン📋 参考代替品（カタログ未掲載）
IRF7319TRPBF
✅ ドロップイン✓ 在庫あり
$0.62 / 個
データシートを見る →Si2309DS
✅ ドロップイン📋 参考代替品（カタログ未掲載）
AO3401A
✅ ドロップイン📋 参考代替品（カタログ未掲載）
BSL207SPH6327XTSA1
✅ ドロップイン✓ 在庫あり
$0.33 / 個
データシートを見る →IRF7205TRPBF 最大定格＆電気的特性
| FET Type | P-Channel MOSFET |
| Technology | IR HEXFET (4th generation) |
| Drain-to-Source Voltage (VDS) | -30 V |
| Continuous Drain Current (ID) at TA=25°C | -4.6 A |
| On-Resistance RDS(on) max @ VGS=-10V | 70 mΩ |
| On-Resistance RDS(on) max @ VGS=-4.5V | 130 mΩ |
| Gate Threshold Voltage VGS(th) | -1.0 V to -3.0 V |
| Total Gate Charge Qg | 27 nC |
| 消費電力（TC=25°C） | 2.5 W |
| 動作接合温度 | -55 °C to +150 °C |
| パッケージ | SO-8 (8-SO) |
| 実装タイプ | Surface Mount |
| RoHS / Lead-Free | Lead-Free (PBF suffix), RoHS compliant |
| Packaging | Tape & Reel (TR suffix) |
IRF7205TRPBF ピン構成
| ピン 1 | Source — Source terminal (P-channel) |
| ピン 2 | Source — Source terminal (P-channel) |
| ピン 3 | Source — Source terminal (P-channel) |
| ピン 4 | Gate — Gate control input (drive negative to turn on) |
| ピン 5 | Drain — Drain terminal (P-channel), thermally connected to pads |
| ピン 6 | Drain — Drain terminal (P-channel), thermally connected to pads |
| ピン 7 | Drain — Drain terminal (P-channel), thermally connected to pads |
| ピン 8 | Drain — Drain terminal (P-channel), thermally connected to pads |
安全動作領域 (DC, TC=25°C)
主な用途
IRF7205TRPBF の用途: 6 件s: 12V Automotive High-Side Load Switch, Battery Protection / Reverse-Polarity Blocking, DC-DC Synchronous Rectifier Replacement, Industrial 24V Power-Rail Switching, USB Power Switch / Hot-Plug Controller, Motor-Drive Half-Bridge Stage.
12V Automotive High-Side Load Switch
The IRF7205TRPBF is a strong fit for 12V automotive high-side load switching where its -30V VDS rating provides margin above 12V nominal plus load-dump transients. With 70 mΩ Rds(on) at VGS=-10V and -4.6A continuous current capability, the device keeps conduction losses below 200 mW at 2 A continuous load, suiting it for driving automotive lamps, solenoids, and small motors where the P-channel topology eliminates the need for a bootstrap circuit and lets a low-side gate-driver MOSFET pull the IRF7205TRPBF gate to ground for turn-on.
おすすめ
Battery Protection / Reverse-Polarity Blocking
For battery protection and reverse-polarity blocking in portable and handheld equipment, the IRF7205TRPBF's P-channel enhancement-mode behavior is ideal because it conducts when the gate is pulled below ground by the load. The 70 mΩ Rds(on) minimizes voltage drop during discharge, while the -30V VDS protects against reversed-battery transients when a Schottky TVS clamps the surge. The SO-8 footprint enables compact PCB designs and the 27 nC total gate charge allows fast disconnect response (<1 μs) under battery-fault conditions.
おすすめ
DC-DC Synchronous Rectifier Replacement
The IRF7205TRPBF can replace the synchronous-rectifier MOSFET in low-power buck converters operating below 4A continuous output where P-channel high-side switching simplifies gate drive by eliminating the bootstrap network. Its 70 mΩ Rds(on) at -10V VGS keeps synchronous-rectifier conduction loss below 4% at 3A output, and the 27 nC Qg enables switching frequencies above 500 kHz with standard CMOS gate drivers. The SO-8 package's thermal pad supports sustained operation at 2-3A continuous when PCB copper pours are designed correctly.
おすすめ
Industrial 24V Power-Rail Switching
For industrial 24V power-rail switching and signal-line multiplexing, the IRF7205TRPBF's -30V VDS rating provides 25% headroom above the 24V nominal bus, withstanding inductive kickback from relays and solenoids on the load side. The P-channel high-side configuration lets a microcontroller I/O pin drive the gate directly through a pull-up resistor, eliminating the high-voltage gate-drive circuitry required by N-channel high-side switches. The 4.6A continuous capability covers most PLC output and sensor-power rail applications in industrial automation.
おすすめ
USB Power Switch / Hot-Plug Controller
The IRF7205TRPBF functions as a USB power-distribution switch where its P-channel high-side topology and -4.6A current capability comfortably exceed the USB 3.0 900 mA and USB-C 1.5 A specification limits. The 70 mΩ Rds(on) creates less than 100 mV drop at 1.5 A, well within USB voltage-tolerance specifications, and the fast-switching 27 nC Qg enables sub-microsecond turn-on that prevents inrush surges when downstream bulk capacitors charge. SO-8 surface-mount assembly suits compact hub designs.
おすすめ
Motor-Drive Half-Bridge Stage
In small DC-motor half-bridge and brushed-DC motor-driver stages for robotics and small appliances, the IRF7205TRPBF serves as the high-side switch in a complementary half-bridge with an N-channel low-side MOSFET. The -30V VDS rating handles 12V motor back-EMF transients, while 70 mΩ Rds(on) limits conduction loss during PWM commutation at duty cycles up to 95%. The 27 nC Qg supports PWM frequencies above 25 kHz, placing switching noise above the audible range for quiet motor operation.
おすすめ
おすすめ製品の概要
エンジニアリング参考データ: IRF7205TRPBF — 比較、設計ガイダンス、コンプライアンス情報。
選定ガイド
代替品との比較
| パラメータ | この製品 | IRF7205PBF | IRF7207TRPBF | Si2309DS | AO3401A |
|---|---|---|---|---|---|
| Brand | Infineon Technologies | Infineon Technologies | Infineon Technologies | Vishay Intertechnology | Alpha & Omega Semiconductor |
| Package | SO-8 (8-SO) | SO-8 (8-SO) - same | SO-8 (8-SO) - same | SO-8 (8-SO) - same | SO-8 (8-SO) - same |
| Polarity | P-Channel | P-Channel | P-Channel | P-Channel | P-Channel |
| Drain-Source Voltage VDS | -30 V | -30 V | -30 V | -30 V | -30 V |
| Continuous Drain Current (TA=25°C) | -4.6 A | -4.6 A | -6.5 A | -3.6 A | -4.0 A |
| On-Resistance Rds(on) @ VGS=-10V | 70 mΩ | 70 mΩ | 60 mΩ | 52 mΩ | 50 mΩ |
| Power Dissipation (TC=25°C) | 2.5 W | 2.5 W | 2.5 W | 1.7 W | 1.4 W |
| Unit Price (qty 1, USD) | 0.55 | 0.55 | 0.65 | 0.40 | 0.18 |
主な差別化要因
- Lowest cost per mΩ in the SO-8 -30V P-channel class （vs AO3401A)
- Industry-standard IR HEXFET fourth-generation process （vs Si2309DS)
- Higher continuous current than typical SO-8 P-channel parts （vs Si2309DS)
設計ノート
Estimated: at 4.6 A continuous and VGS=-10V drive, conduction loss is approximately 1.5 W (I² × R = 4.6² × 0.07 = 1.48 W). The SO-8 package's theta_JA is approximately 50 °C/W on a 1-square-inch copper pad, giving a junction temperature rise of 75 °C above ambient. Above 3 A continuous load, use a maximum copper-pad area of at least 1 square inch with thermal vias to inner planes; this is the most common design pitfall when migrating from D2PAK to SO-8.
Lay out the SO-8 footprint with a continuous thermal pad (Exposed Pad) under pins 5-6-7-8 connected to a copper pour of at least 1 square inch. Add 0.3 mm thermal vias in a 1.2 mm pitch grid stitching the top copper pour to the inner ground plane. The gate trace should be kept short (<10 mm) and routed away from switching drain traces to minimize dv/dt-induced gate bounce. Per Infineon's SO-8 layout application note, vias-in-pad are acceptable but require filled-and-plated-over via process to prevent solder wicking.
Do not exceed -20V VGS (the absolute-maximum gate-source voltage); use a 12V Zener clamp across gate-source if the gate-drive signal can overshoot. Do not parallel multiple IRF7205TRPBF devices without individual gate-source resistors because the negative-temperature-coefficient of Rds(on) at high currents can cause thermal runaway. Avoid operating at VDS > -24V for sustained periods to stay below 80% of the -30V rating and provide margin against automotive load-dump transients.
コンプライアンス情報
Pb-free per PBF suffix, RoHS compliant per Infineon product page. Not AEC-Q100 qualified - automotive AEC-Q100 applications should consider AEC-Q100-qualified alternatives or perform additional qualification testing.
