onsemi

MC33202PG - 2.2 MHz Dual Rail-to-Rail Op Amp | onsemi

部品番号: MC33202PG ✓ 生産中
1.8 V to 12 V Vdss 8-pin PDIP Package
MOQ: 1 |

MC33202PG 概要

onsemi MC33202PG is a dual, low-voltage, rail-to-rail input and output operational amplifier with a 2.2 MHz gain-bandwidth product, 1 V/µs slew rate, and a 1.8 V to 12 V supply range in an 8-pin PDIP package. The device supports industrial-temperature operation from -40 °C to 105 °C and provides two amplifier circuits in one package.

An operational amplifier is an analog signal-processing IC that amplifies the voltage difference between its non-inverting and inverting inputs. The MC33202PG belongs to the rail-to-rail operational-amplifier family, combining input and output common-mode capability with low-voltage operation. This places it within the broader hierarchy of analog ICs, signal-conditioning ICs, amplifiers, and general-purpose operational amplifiers.

Rail-to-rail input operation allows the input voltage to approach either supply rail. According to the onsemi datasheet, inputs can be driven as high as 200 mV beyond the supply rails without causing phase reversal in the outputs. Rail-to-rail output operation allows each output to swing within approximately 50 mV of its corresponding rail, improving output range utilization in low-voltage systems.

The MC33202PG combines a 2.2 MHz gain-bandwidth product with a 1 V/µs slew rate. These values make it suitable for general-purpose signal amplification, low-voltage analog interfaces, and feedback-control circuits where operating from a single 1.8 V supply is useful. Its dual configuration can reduce board area when two independent amplifier channels are required.

Typical uses include sensor-interface amplification, audio and communication signal conditioning, voltage buffering, active filtering, and industrial control-system analog sections. The 1.8 V minimum supply supports portable and embedded systems, while the -40 °C to 105 °C temperature range supports industrial environments when the complete system is qualified for the intended conditions.

Designers should verify input and output limits under the selected supply voltage and load current. Input and output stability should be evaluated with the actual source impedance, feedback network, load, and bypass capacitance. Because this is a through-hole PDIP device, its larger footprint must be considered when replacing it with surface-mount alternatives.

This product summary combines the MC33202PG electrical ratings, package information, pin assignment, practical application guidance, and qualified same-footprint replacement information. The alternatives are restricted to devices presented as pin-to-pin compatible rather than merely similar amplifiers, helping engineers identify a practical migration path without implying electrical identity.

ドロップイン代替品: MC33202PG — 同一パッケージでピン互換。PCBの作り直しが必要な異なるパッケージの部品は除外されています。

TS3V912IN

✅ ドロップイン
📦 8-pin PDIP
Dual rail-to-rail input/output topology and 8-pin PDIP format match the MC33202PG; detailed bandwidth, slew-rate, offset, and bias-current differences must be checked before approval

📋 参考代替品(カタログ未掲載)

MC33202PG 最大定格&電気的特性

Number of Amplifier Circuits 2 circuits
Amplifier Type General-purpose operational amplifier
Supply Voltage Range 1.8 V to 12 V
Gain-Bandwidth Product 2.2 MHz
Slew Rate 1 V/µs
Input Common-Mode Range Rail-to-rail; inputs can be driven 200 mV beyond the supply rails without output phase reversal
Output Swing Within approximately 50 mV of each rail
動作温度範囲 -40 °C to 105 °C
Temperature Grade Industrial
ピン数 8 pins
パッケージ 8-pin PDIP
実装タイプ Through-hole
Terminal Form Through-hole
Supply Voltage Type Single or dual supply operation

MC33202PG 8-pin pdip ピン配置ガイド

MC33202PG (8-pin pdip パッケージ) のピン配置。 このアナログコンポーネントは、入力、出力、および電源ピンを備えています。オフセットナル、補償、イネーブルピンの設定については、メーカーのデータシートを参照してください。信号調整やアンプ回路に最適です。

MC33202PG の 8-pin pdip パッケージピン配置図

詳細なピン配置データはありません: MC33202PG.

詳細は データシート をご参照ください。

主な用途

MC33202PG の用途: 3 件s: 信号コンディショニング, データ収集, オーディオ処理.

📊

信号コンディショニング

MC33202PGを使用したセンサー信号の増幅とフィルタリング。

📈

データ収集

MC33202PGによるデジタル処理用のアナログ信号変換。

🎧

オーディオ処理

MC33202PGによるオーディオ信号の増幅と処理。

What is the operating voltage of MC33202PG?
The MC33202PG operates from a 1.8 V to 12 V supply range. According to the onsemi datasheet, the device is intended for low-voltage dual operational-amplifier systems and can be used with single or split supplies. The 1.8 V minimum makes it suitable for portable, embedded, and industrial interface circuits, although input, output, and decoupling requirements must still be evaluated for the selected supply voltage.
What are the key specifications of MC33202PG that engineers should know?
The MC33202PG is a dual, rail-to-rail operational amplifier with a 2.2 MHz gain-bandwidth product, 1 V/µs slew rate, and 1.8 V to 12 V supply range. According to the onsemi datasheet, its inputs may be driven 200 mV beyond the supply rails without output phase reversal, while its outputs can swing within approximately 50 mV of each rail. The device is packaged in an 8-pin PDIP and rated for -40 °C to 105 °C operation.
Where can I find the MC33202PG pinout?
The MC33202PG pinout is identified in the pin-connection section of the onsemi datasheet, available through the datasheet link on this page. The device uses an 8-pin PDIP configuration with two amplifier channels, supply pins, and an exposed connection for amplifier A. Use the numbered package drawing when assigning PCB traces and confirm orientation against the physical pin-1 marker before soldering.
Where to download the MC33202PG datasheet PDF?
The MC33202PG datasheet PDF can be accessed through the datasheet link on this page and through the linked MC33202PG document listing. The manufacturer document covers the dual rail-to-rail amplifier family, electrical characteristics, typical applications, and package information. Review the same onsemi document before making power-supply, input-range, output-swing, or stability decisions for a new design.
Is MC33202PG a dual rail-to-rail operational amplifier?
The MC33202PG contains two general-purpose operational-amplifier channels with rail-to-rail input and output behavior. According to the onsemi datasheet, inputs can be driven as much as 200 mV beyond the supply rails without phase reversal, and the outputs can swing within approximately 50 mV of each rail. Its 2.2 MHz bandwidth and 1 V/µs slew rate suit general low-voltage analog signal conditioning.
Can TS3V912IN replace MC33202PG as a drop-in part?
The TS3V912IN is the closest qualified drop-in candidate for the MC33202PG because it is presented as a dual general-purpose, rail-to-rail input/output amplifier in an 8-pin PDIP configuration. It remains necessary to compare supply voltage, bandwidth, slew rate, output swing, input bias current, and DC accuracy against the onsemi datasheet before approving a substitution. PCB compatibility alone does not guarantee identical system behavior.
What can replace the MC33202PG?
The TS3V912IN is the supported drop-in replacement candidate identified for the MC33202PG in the same 8-pin PDIP format. For an existing PCB, verify that the amplifier channels, supply pins, and pin orientation are unchanged, then compare key AC and DC parameters. Other similar dual rail-to-rail amplifiers should not be treated as drop-in replacements unless their exact package and pin assignment are confirmed.
MC33202PG vs TS3V912IN - which is better for low-voltage signal conditioning?
The MC33202PG is preferable when its documented 1.8 V to 12 V range, 2.2 MHz bandwidth, and onsemi-specific operating limits are already validated in the design. The TS3V912IN may be preferable when it is the qualified same-footprint replacement and its electrical characteristics better satisfy the application. Compare input offset voltage, input bias current, output swing, noise, stability, and supply limits before making the choice.
When should I choose MC33202PG instead of TS3V912IN?
Choose the MC33202PG when you prefer to retain the originally qualified onsemi device or when its 2.2 MHz bandwidth, 1 V/µs slew rate, and specified low-voltage behavior match the circuit. Choose the TS3V912IN when it is the approved same-pin replacement and its parameters meet the design requirements. The decision should be based on an application-level comparison rather than package appearance alone.
Is MC33202PG suitable for industrial control applications?
The MC33202PG is suitable for many industrial control applications because it is marked as an industrial-temperature device with an operating range of -40 °C to 105 °C. Its dual rail-to-rail channels support low-level sensor conditioning, buffering, and feedback functions. The complete assembly still requires environmental qualification, suitable bypass capacitors, grounding, and protection appropriate to the installed enclosure and signal environment.
What is the lead time for MC33202PG?
The current lead time and available production quantity should be requested through the Request a Quote form on this page. The product is offered as an 8-pin PDIP industrial-grade device, but delivery timing can vary with order quantity and market conditions. Submit the required quantity, date code preference, and shipment destination with the quotation request for an actionable supply commitment.
Where can I buy MC33202PG online?
Use the Request a Quote form on this page to request MC33202PG availability, production quantity, and a firm quotation. The form supports procurement review without embedding a static price that can become outdated. Include the 8-pin PDIP package, industrial temperature range, target quantity, and any date-code or traceability requirements when submitting the request.
What is the price of MC33202PG?
The current MC33202PG price is presented through the Request a Quote form on this page so that quantity, sourcing condition, and supply timing can be reflected accurately. Request a quotation for the exact 8-pin PDIP industrial-grade MPN and indicate your required quantity and delivery schedule. This avoids relying on a historical unit-price figure that may not match current availability.
Is MC33202PG in stock?
Current MC33202PG stock should be confirmed through the Request a Quote form on this page, which routes the request for an inventory and delivery commitment. The product is listed for active purchasing, but exact on-hand quantity can change rapidly. State the required order quantity and target date when requesting availability confirmation.
What are the best Texas Instruments cross references for MC33202PG?
The Texas Instruments cross-reference discussion identifies TLV9302, TLV9102, TLV9352, and TLV9152 as candidates related to the MC33202 and related amplifier families. They are not all guaranteed to use the MC33202PG's 8-pin PDIP footprint, so they are not automatically PCB drop-in replacements. Check the exact TI package option and pin assignment before considering any of these devices.
How do I design a stable MC33202PG analog circuit?
Start with the onsemi datasheet and keep each feedback network short and physically compact. Place power-bypass capacitors close to the supply pins, use realistic source impedances, and verify operation over the full 1.8 V to 12 V supply range. If driving capacitive loads or operating near output-swing limits, test the complete circuit because amplifier stability and transient behavior can depend on load, layout, and component tolerances.

エンジニアリング参考データ: MC33202PG — 比較、設計ガイダンス、コンプライアンス情報。

選定ガイド

Choose the MC33202PG when maintaining an onsemi-based industrial design and the documented 1.8 V to 12 V operating range, 2.2 MHz bandwidth, and 1 V/µs slew rate satisfy the circuit. Choose the TS3V912IN when it is the approved 8-pin PDIP replacement and its detailed AC and DC specifications provide a better match for the application. Because the two devices may differ in offset voltage, bias current, noise, output swing, stability, and supply limits, compare those parameters at the actual operating point rather than relying on topology alone. For new compact products, evaluate a modern surface-mount amplifier separately, but that requires a footprint change and is not a drop-in migration. The MC33202PG remains appropriate when through-hole construction, onsemi continuity, and the established industrial temperature range are priorities.

代替品との比較

パラメータ この製品 TS3V912IN
Package 8-pin PDIP 8-pin PDIP
Brand onsemi Texas Instruments
Amplifier Count 2 circuits 2 circuits
Input Common-Mode Behavior Rail-to-rail; inputs may be driven 200 mV beyond the rails without output phase reversal Rail-to-rail input
Output Common-Mode Behavior Rail-to-rail; output within approximately 50 mV of each rail Rail-to-rail output
Mounting Style Through-hole Through-hole

主な差別化要因

  • Original onsemi device with a documented low-voltage operating range (vs TS3V912IN)
  • Dual rail-to-rail operation in an industrial-temperature package (vs TS3V912IN)
  • Documented input over-rail and output-swing characteristics (vs TS3V912IN)

設計ノート

Do not treat rail-to-rail input as permission to exceed the absolute maximum input voltage. Although the MC33202PG can accept inputs 200 mV beyond a supply rail without phase reversal, excessive overdrive can increase current, stress the input stage, or damage the device. Clamp external signals to safe limits and include the power-off state when selecting protection components.

Place the supply bypass capacitors close to the amplifier supply pins and connect the exposed supply and ground pins to low-impedance planes. Keep feedback components adjacent to their associated amplifier pins to minimize parasitic coupling. Because the MC33202PG is an 8-pin PDIP, check the physical pin orientation and socket or lead spacing before inserting a substitute.

Evaluate output settling, slew-rate margin, and channel-to-channel behavior using the intended signal bandwidth. The specified 2.2 MHz gain-bandwidth product and 1 V/µs slew rate support general-purpose low-voltage analog circuits, but large-signal settling can become the limiting factor at low frequencies or high output amplitudes. Use the manufacturer's test methods and application guidance when setting gain and feedback values.

Verify operation across the complete 1.8 V to 12 V supply range rather than testing only at a nominal voltage. The output-swing limit depends on supply headroom, load, and output configuration, while input behavior changes near the rails. Confirm that every downstream signal remains within the amplifier's operating limits at minimum supply, maximum load, and temperature extremes.

コンプライアンス情報

RoHS
Unknown
REACH
Unknown
AEC-Q100
Not Applicable
鉛フリー
Unknown
ハロゲンフリー
Unknown
紛争鉱物
Unknown

The MC33202PG is identified as an industrial-grade component, but no specific RoHS, REACH, AEC-Q100, lead-free, halogen-free, or conflict-minerals declaration was identified. AEC-Q100 is not applicable because this is a general-purpose operational amplifier rather than an automotive-qualified device.

データ検証日: 2026-11-16 — データはXAIPARTの部品エンジニアリングチームによって検証・管理されています

関連検索

mc33202p pinout mc33202p datasheet MC33202PG datasheet MC33202PG pinout MC33202PG datasheet pdf MC33202PG equivalent MC33202PG replacement MC33202PG vs TS3V912IN MC33202PG application circuit MC33202PG 2.2 MHz op amp MC33202PG 1.8V dual amplifier onsemi MC33202PG MC33202PG price MC33202PG stock

関連部品&用語

onsemi MC33202PG MC33202P TS3V912IN TLV9302 TLV9102 TLV9352 TLV9152 Operational amplifier Dual operational amplifier Rail-to-rail input Rail-to-rail output General-purpose amplifier Analog IC Signal-conditioning IC Low-voltage amplifier Gain-bandwidth product Slew rate Input offset voltage Supply voltage 8-pin PDIP PDIP package family Through-hole mounting Industrial temperature grade Sensor interface
クイック見積RFQ
詳細をすべてご記入ください — 営業チームが24時間以内にご返信いたします
部品番号 メーカー パッケージ QTY 目標価格 小計
✓
見積を送信しました!

24時間以内にメールでご返信いたします

1
RFQ送信済み
2
見積受領
3
注文済み
4
お支払い
5
発送済み
6
配達済み
RFQの詳細を表示