MC33202PG - 2.2 MHz Dual Rail-to-Rail Op Amp | onsemi
부품 번호: MC33202PG ✓ 활성MC33202PG 개요
An operational amplifier is an analog signal-processing IC that amplifies the voltage difference between its non-inverting and inverting inputs. The MC33202PG belongs to the rail-to-rail operational-amplifier family, combining input and output common-mode capability with low-voltage operation. This places it within the broader hierarchy of analog ICs, signal-conditioning ICs, amplifiers, and general-purpose operational amplifiers.
Rail-to-rail input operation allows the input voltage to approach either supply rail. According to the onsemi datasheet, inputs can be driven as high as 200 mV beyond the supply rails without causing phase reversal in the outputs. Rail-to-rail output operation allows each output to swing within approximately 50 mV of its corresponding rail, improving output range utilization in low-voltage systems.
The MC33202PG combines a 2.2 MHz gain-bandwidth product with a 1 V/µs slew rate. These values make it suitable for general-purpose signal amplification, low-voltage analog interfaces, and feedback-control circuits where operating from a single 1.8 V supply is useful. Its dual configuration can reduce board area when two independent amplifier channels are required.
Typical uses include sensor-interface amplification, audio and communication signal conditioning, voltage buffering, active filtering, and industrial control-system analog sections. The 1.8 V minimum supply supports portable and embedded systems, while the -40 °C to 105 °C temperature range supports industrial environments when the complete system is qualified for the intended conditions.
Designers should verify input and output limits under the selected supply voltage and load current. Input and output stability should be evaluated with the actual source impedance, feedback network, load, and bypass capacitance. Because this is a through-hole PDIP device, its larger footprint must be considered when replacing it with surface-mount alternatives.
This product summary combines the MC33202PG electrical ratings, package information, pin assignment, practical application guidance, and qualified same-footprint replacement information. The alternatives are restricted to devices presented as pin-to-pin compatible rather than merely similar amplifiers, helping engineers identify a practical migration path without implying electrical identity.
드롭인 대체품: MC33202PG — 동일 패키지, 핀 호환. PCB 재작업이 필요한 다른 패키지 부품은 제외됩니다.
TS3V912IN
✅ 드롭인📋 참조 대체품 (카탈로그에 없음)
MC33202PG 최대 정격 & 전기적 특성
| Number of Amplifier Circuits | 2 circuits |
| Amplifier Type | General-purpose operational amplifier |
| Supply Voltage Range | 1.8 V to 12 V |
| Gain-Bandwidth Product | 2.2 MHz |
| Slew Rate | 1 V/µs |
| Input Common-Mode Range | Rail-to-rail; inputs can be driven 200 mV beyond the supply rails without output phase reversal |
| Output Swing | Within approximately 50 mV of each rail |
| 동작 온도 범위 | -40 °C to 105 °C |
| Temperature Grade | Industrial |
| 핀 수 | 8 pins |
| 패키지 | 8-pin PDIP |
| 실장 유형 | Through-hole |
| Terminal Form | Through-hole |
| Supply Voltage Type | Single or dual supply operation |
MC33202PG 8-pin pdip 핀 구성 가이드
MC33202PG(8-pin pdip 패키지)의 핀 구성입니다. 이 아날로그 부품에는 입력, 출력, 전원 공급 핀이 있습니다. 오프셋 널, 보상, 인에이블 핀 구성은 제조사 데이터시트를 참조하십시오. 신호 컨디셔닝 및 증폭기 회로에 이상적입니다.
다음에 대한 상세 핀아웃 데이터 없음: MC33202PG.
다음을 참조하십시오: 데이터시트 전체 핀 구성은 다음을 참조하십시오.
일반적인 애플리케이션
MC33202PG 적합 용도: 3 애플리케이션s: 신호 컨디셔닝, 데이터 수집, 오디오 처리.
신호 컨디셔닝
MC33202PG을(를) 사용한 센서 신호 증폭 및 필터링.
데이터 수집
MC33202PG을(를) 사용한 디지털 처리를 위한 아날로그 신호 변환.
오디오 처리
MC33202PG을(를) 사용한 오디오 신호 증폭 및 처리.
엔지니어링 참조 데이터: MC33202PG — 비교, 설계 지침 및 규정 준수 정보.
선택 가이드
대체품과의 비교
| 파라미터 | 이 제품 | TS3V912IN |
|---|---|---|
| Package | 8-pin PDIP | 8-pin PDIP |
| Brand | onsemi | Texas Instruments |
| Amplifier Count | 2 circuits | 2 circuits |
| Input Common-Mode Behavior | Rail-to-rail; inputs may be driven 200 mV beyond the rails without output phase reversal | Rail-to-rail input |
| Output Common-Mode Behavior | Rail-to-rail; output within approximately 50 mV of each rail | Rail-to-rail output |
| Mounting Style | Through-hole | Through-hole |
주요 차별점
- Original onsemi device with a documented low-voltage operating range (vs TS3V912IN)
- Dual rail-to-rail operation in an industrial-temperature package (vs TS3V912IN)
- Documented input over-rail and output-swing characteristics (vs TS3V912IN)
설계 노트
Do not treat rail-to-rail input as permission to exceed the absolute maximum input voltage. Although the MC33202PG can accept inputs 200 mV beyond a supply rail without phase reversal, excessive overdrive can increase current, stress the input stage, or damage the device. Clamp external signals to safe limits and include the power-off state when selecting protection components.
Place the supply bypass capacitors close to the amplifier supply pins and connect the exposed supply and ground pins to low-impedance planes. Keep feedback components adjacent to their associated amplifier pins to minimize parasitic coupling. Because the MC33202PG is an 8-pin PDIP, check the physical pin orientation and socket or lead spacing before inserting a substitute.
Evaluate output settling, slew-rate margin, and channel-to-channel behavior using the intended signal bandwidth. The specified 2.2 MHz gain-bandwidth product and 1 V/µs slew rate support general-purpose low-voltage analog circuits, but large-signal settling can become the limiting factor at low frequencies or high output amplitudes. Use the manufacturer's test methods and application guidance when setting gain and feedback values.
Verify operation across the complete 1.8 V to 12 V supply range rather than testing only at a nominal voltage. The output-swing limit depends on supply headroom, load, and output configuration, while input behavior changes near the rails. Confirm that every downstream signal remains within the amplifier's operating limits at minimum supply, maximum load, and temperature extremes.
규정 준수 정보
The MC33202PG is identified as an industrial-grade component, but no specific RoHS, REACH, AEC-Q100, lead-free, halogen-free, or conflict-minerals declaration was identified. AEC-Q100 is not applicable because this is a general-purpose operational amplifier rather than an automotive-qualified device.