MC33202PG - 2.2 MHz Dual Rail-to-Rail Op Amp | onsemi
料号: MC33202PG ✓ 量产中MC33202PG 概述
An operational amplifier is an analog signal-processing IC that amplifies the voltage difference between its non-inverting and inverting inputs. The MC33202PG belongs to the rail-to-rail operational-amplifier family, combining input and output common-mode capability with low-voltage operation. This places it within the broader hierarchy of analog ICs, signal-conditioning ICs, amplifiers, and general-purpose operational amplifiers.
Rail-to-rail input operation allows the input voltage to approach either supply rail. According to the onsemi datasheet, inputs can be driven as high as 200 mV beyond the supply rails without causing phase reversal in the outputs. Rail-to-rail output operation allows each output to swing within approximately 50 mV of its corresponding rail, improving output range utilization in low-voltage systems.
The MC33202PG combines a 2.2 MHz gain-bandwidth product with a 1 V/µs slew rate. These values make it suitable for general-purpose signal amplification, low-voltage analog interfaces, and feedback-control circuits where operating from a single 1.8 V supply is useful. Its dual configuration can reduce board area when two independent amplifier channels are required.
Typical uses include sensor-interface amplification, audio and communication signal conditioning, voltage buffering, active filtering, and industrial control-system analog sections. The 1.8 V minimum supply supports portable and embedded systems, while the -40 °C to 105 °C temperature range supports industrial environments when the complete system is qualified for the intended conditions.
Designers should verify input and output limits under the selected supply voltage and load current. Input and output stability should be evaluated with the actual source impedance, feedback network, load, and bypass capacitance. Because this is a through-hole PDIP device, its larger footprint must be considered when replacing it with surface-mount alternatives.
This product summary combines the MC33202PG electrical ratings, package information, pin assignment, practical application guidance, and qualified same-footprint replacement information. The alternatives are restricted to devices presented as pin-to-pin compatible rather than merely similar amplifiers, helping engineers identify a practical migration path without implying electrical identity.
直接替换替代料: MC33202PG ——相同封装,引脚兼容。需要 PCB 改动的不同封装料号已排除。
TS3V912IN
✅ 直接替换📋 参考替代料(不在目录中)
MC33202PG 最大额定值与电气特性
| Number of Amplifier Circuits | 2 circuits |
| Amplifier Type | General-purpose operational amplifier |
| Supply Voltage Range | 1.8 V to 12 V |
| Gain-Bandwidth Product | 2.2 MHz |
| Slew Rate | 1 V/µs |
| Input Common-Mode Range | Rail-to-rail; inputs can be driven 200 mV beyond the supply rails without output phase reversal |
| Output Swing | Within approximately 50 mV of each rail |
| 工作温度范围 | -40 °C to 105 °C |
| Temperature Grade | Industrial |
| 引脚数 | 8 pins |
| 封装 | 8-pin PDIP |
| 安装类型 | Through-hole |
| Terminal Form | Through-hole |
| Supply Voltage Type | Single or dual supply operation |
MC33202PG 8-pin pdip 引脚配置指南
MC33202PG(8-pin pdip 封装)的引脚配置。 该模拟元件具有输入、输出和电源引脚。请参阅制造商数据手册以了解失调调零、补偿和使能引脚配置。适用于信号调理和放大器电路。
暂无详细引脚数据: MC33202PG.
请参阅 数据手册 以查看完整引脚配置。
典型应用
MC33202PG 适用于 3 应用s: 信号调理, 数据采集, 音频处理.
信号调理
使用 MC33202PG 放大和滤波传感器信号。
数据采集
使用 MC33202PG 将模拟信号转换为数字信号进行处理。
音频处理
使用 MC33202PG 进行音频信号放大和处理。
工程参考数据: MC33202PG ——对比、设计指导和合规信息。
选型指南
与替代料对比
| 参数 | 本产品 | TS3V912IN |
|---|---|---|
| Package | 8-pin PDIP | 8-pin PDIP |
| Brand | onsemi | Texas Instruments |
| Amplifier Count | 2 circuits | 2 circuits |
| Input Common-Mode Behavior | Rail-to-rail; inputs may be driven 200 mV beyond the rails without output phase reversal | Rail-to-rail input |
| Output Common-Mode Behavior | Rail-to-rail; output within approximately 50 mV of each rail | Rail-to-rail output |
| Mounting Style | Through-hole | Through-hole |
关键差异点
- Original onsemi device with a documented low-voltage operating range (对比 TS3V912IN)
- Dual rail-to-rail operation in an industrial-temperature package (对比 TS3V912IN)
- Documented input over-rail and output-swing characteristics (对比 TS3V912IN)
设计说明
Do not treat rail-to-rail input as permission to exceed the absolute maximum input voltage. Although the MC33202PG can accept inputs 200 mV beyond a supply rail without phase reversal, excessive overdrive can increase current, stress the input stage, or damage the device. Clamp external signals to safe limits and include the power-off state when selecting protection components.
Place the supply bypass capacitors close to the amplifier supply pins and connect the exposed supply and ground pins to low-impedance planes. Keep feedback components adjacent to their associated amplifier pins to minimize parasitic coupling. Because the MC33202PG is an 8-pin PDIP, check the physical pin orientation and socket or lead spacing before inserting a substitute.
Evaluate output settling, slew-rate margin, and channel-to-channel behavior using the intended signal bandwidth. The specified 2.2 MHz gain-bandwidth product and 1 V/µs slew rate support general-purpose low-voltage analog circuits, but large-signal settling can become the limiting factor at low frequencies or high output amplitudes. Use the manufacturer's test methods and application guidance when setting gain and feedback values.
Verify operation across the complete 1.8 V to 12 V supply range rather than testing only at a nominal voltage. The output-swing limit depends on supply headroom, load, and output configuration, while input behavior changes near the rails. Confirm that every downstream signal remains within the amplifier's operating limits at minimum supply, maximum load, and temperature extremes.
合规信息
The MC33202PG is identified as an industrial-grade component, but no specific RoHS, REACH, AEC-Q100, lead-free, halogen-free, or conflict-minerals declaration was identified. AEC-Q100 is not applicable because this is a general-purpose operational amplifier rather than an automotive-qualified device.