MC33202PG - 2.2 MHz Dual Rail-to-Rail Op Amp | onsemi
MPN: MC33202PG ✓ Hoạt độngMC33202PG Tóm tắt
An operational amplifier is an analog signal-processing IC that amplifies the voltage difference between its non-inverting and inverting inputs. The MC33202PG belongs to the rail-to-rail operational-amplifier family, combining input and output common-mode capability with low-voltage operation. This places it within the broader hierarchy of analog ICs, signal-conditioning ICs, amplifiers, and general-purpose operational amplifiers.
Rail-to-rail input operation allows the input voltage to approach either supply rail. According to the onsemi datasheet, inputs can be driven as high as 200 mV beyond the supply rails without causing phase reversal in the outputs. Rail-to-rail output operation allows each output to swing within approximately 50 mV of its corresponding rail, improving output range utilization in low-voltage systems.
The MC33202PG combines a 2.2 MHz gain-bandwidth product with a 1 V/µs slew rate. These values make it suitable for general-purpose signal amplification, low-voltage analog interfaces, and feedback-control circuits where operating from a single 1.8 V supply is useful. Its dual configuration can reduce board area when two independent amplifier channels are required.
Typical uses include sensor-interface amplification, audio and communication signal conditioning, voltage buffering, active filtering, and industrial control-system analog sections. The 1.8 V minimum supply supports portable and embedded systems, while the -40 °C to 105 °C temperature range supports industrial environments when the complete system is qualified for the intended conditions.
Designers should verify input and output limits under the selected supply voltage and load current. Input and output stability should be evaluated with the actual source impedance, feedback network, load, and bypass capacitance. Because this is a through-hole PDIP device, its larger footprint must be considered when replacing it with surface-mount alternatives.
This product summary combines the MC33202PG electrical ratings, package information, pin assignment, practical application guidance, and qualified same-footprint replacement information. The alternatives are restricted to devices presented as pin-to-pin compatible rather than merely similar amplifiers, helping engineers identify a practical migration path without implying electrical identity.
Bộ thay thế dễ dàng lắp đặt cho MC33202PG — cùng gói, chân-to-chân tương thích. Các bộ phận yêu cầu hàn PCB bị loại trừ.
TS3V912IN
✅ Drop-In📋 Tham chiếu thay thế (không có trong danh mục)
MC33202PG Tỷ lệ tối đa & tính chất điện
| Number of Amplifier Circuits | 2 circuits |
| Amplifier Type | General-purpose operational amplifier |
| Supply Voltage Range | 1.8 V to 12 V |
| Gain-Bandwidth Product | 2.2 MHz |
| Slew Rate | 1 V/µs |
| Input Common-Mode Range | Rail-to-rail; inputs can be driven 200 mV beyond the supply rails without output phase reversal |
| Output Swing | Within approximately 50 mV of each rail |
| Khoảng nhiệt độ hoạt động | -40 °C to 105 °C |
| Temperature Grade | Industrial |
| Số lượng chân | 8 pins |
| Hộp | 8-pin PDIP |
| Kiểu lắp đặt | Through-hole |
| Terminal Form | Through-hole |
| Supply Voltage Type | Single or dual supply operation |
Hướng dẫn cấu hình chân MC33202PG 8-pin pdip
Cấu hình chân cho MC33202PG (8-pin pdip gói). Thành phần số hiệu này có chân đầu vào, đầu ra và nguồn cung cấp. Tham khảo tài liệu thông số kỹ thuật của nhà sản xuất để biết cấu hình chân bù, bù trừ và chân kích hoạt. Hoàn hảo cho điều kiện tín hiệu và mạch khuếch đại.
Không có dữ liệu chân cụ thể sẵn có cho MC33202PG.
Tham khảo: tài liệu kỹ thuật cho cấu hình chân đầy đủ.
Ứng dụng tiêu biểu
MC33202PG phù hợp cho 3 Áp dụngs: Điều kiện tín hiệu, Thiết bị thu thập dữ liệu, Xử lý âm thanh.
Điều kiện tín hiệu
Phân tích và lọc tín hiệu cảm biến sử dụng MC33202PG.
Thiết bị thu thập dữ liệu
Chuyển đổi tín hiệu tương tự thành quá trình số sử dụng MC33202PG.
Xử lý âm thanh
Phân tích và khuếch đại tín hiệu âm thanh sử dụng MC33202PG.
Dữ liệu tham khảo kỹ thuật cho MC33202PG — so sánh, hướng dẫn thiết kế và thông tin tuân thủ.
Hướng dẫn chọn lựa
So sánh với các sản phẩm thay thế
| Tham số | Sản phẩm này | TS3V912IN |
|---|---|---|
| Package | 8-pin PDIP | 8-pin PDIP |
| Brand | onsemi | Texas Instruments |
| Amplifier Count | 2 circuits | 2 circuits |
| Input Common-Mode Behavior | Rail-to-rail; inputs may be driven 200 mV beyond the rails without output phase reversal | Rail-to-rail input |
| Output Common-Mode Behavior | Rail-to-rail; output within approximately 50 mV of each rail | Rail-to-rail output |
| Mounting Style | Through-hole | Through-hole |
Bảo phân biệt quan trọng
- Original onsemi device with a documented low-voltage operating range (vsTS3V912IN)
- Dual rail-to-rail operation in an industrial-temperature package (vsTS3V912IN)
- Documented input over-rail and output-swing characteristics (vsTS3V912IN)
Ghi chú thiết kế
Do not treat rail-to-rail input as permission to exceed the absolute maximum input voltage. Although the MC33202PG can accept inputs 200 mV beyond a supply rail without phase reversal, excessive overdrive can increase current, stress the input stage, or damage the device. Clamp external signals to safe limits and include the power-off state when selecting protection components.
Place the supply bypass capacitors close to the amplifier supply pins and connect the exposed supply and ground pins to low-impedance planes. Keep feedback components adjacent to their associated amplifier pins to minimize parasitic coupling. Because the MC33202PG is an 8-pin PDIP, check the physical pin orientation and socket or lead spacing before inserting a substitute.
Evaluate output settling, slew-rate margin, and channel-to-channel behavior using the intended signal bandwidth. The specified 2.2 MHz gain-bandwidth product and 1 V/µs slew rate support general-purpose low-voltage analog circuits, but large-signal settling can become the limiting factor at low frequencies or high output amplitudes. Use the manufacturer's test methods and application guidance when setting gain and feedback values.
Verify operation across the complete 1.8 V to 12 V supply range rather than testing only at a nominal voltage. The output-swing limit depends on supply headroom, load, and output configuration, while input behavior changes near the rails. Confirm that every downstream signal remains within the amplifier's operating limits at minimum supply, maximum load, and temperature extremes.
Thông tin tuân thủ
The MC33202PG is identified as an industrial-grade component, but no specific RoHS, REACH, AEC-Q100, lead-free, halogen-free, or conflict-minerals declaration was identified. AEC-Q100 is not applicable because this is a general-purpose operational amplifier rather than an automotive-qualified device.