OPA633KP - 260MHz High-Speed Buffer | Texas Instruments
部品番号: OPA633KP ✓ 生産中OPA633KP 概要
A high-speed buffer amplifier is a specialized operational-amplifier stage configured primarily for unity gain. It preserves the input signal while providing low output impedance and improved drive capability. Within the amplifier hierarchy, the OPA633KP is a unity-gain buffer, a high-speed analog signal-conditioning IC, and a member of the broader amplifier and semiconductor family. This makes it particularly useful where an upstream amplifier cannot drive the connected load directly.
The principal performance characteristics are its 260 MHz wide bandwidth, 2500 V/µs high slew rate, and 100 mA output current. These specifications allow the buffer to reproduce high-frequency waveforms with improved amplitude and phase behavior compared with slower general-purpose amplifiers. The listed 1.5 mV low offset voltage helps reduce static output error when the device is used as a signal buffer. Its wide supply range accommodates conventional analog systems operating from ±5 V through ±16 V.
OPA633KP uses a dielectric-isolation process that combines NPN and PNP high-frequency transistors, as described by the Burr-Brown and Texas Instruments datasheet. This monolithic construction supports the device’s combination of wide bandwidth and high slew rate. Because it is configured as a unity-gain buffer, it offers a straightforward way to add drive current and isolate a sensitive source from the impedance of a downstream load without intentionally closing a voltage-feedback loop around the device.
Typical applications include video signal buffering, high-speed line driving, ADC input isolation, and current boosting for an existing operational amplifier. It is also suitable for test and measurement equipment, communications interfaces, and instrumentation where a low-impedance output is required. The 100 mA output-current capability gives the buffer more drive authority than a general-purpose precision amplifier, while its 260 MHz bandwidth preserves fast signal content.
The primary design consideration is stability and routing. The OPA633KP is intended for unity-gain use, and high-speed feedback and parasitic capacitance can affect stability or ringing. Keep input and output traces short, use a ground plane, place decoupling capacitors close to the supply pins, and avoid long unprotected routes through which output current can induce feedback. Verify transient behavior with the actual source and load impedances rather than relying only on small-signal bandwidth figures.
This page combines the manufacturer specifications with application guidance, a pin-compatible comparison, design notes, and selection criteria for engineers evaluating the OPA633KP. It helps distinguish the device from ordinary operational amplifiers and clarifies when a dedicated high-speed unity-gain buffer is preferable to using a voltage-feedback amplifier in a nonstandard configuration.
ドロップイン代替品: OPA633KP — 同一パッケージでピン互換。PCBの作り直しが必要な異なるパッケージの部品は除外されています。
このシリーズのバリエーション
同一シリーズでドロップイン互換のモデル: OPA633KP (同一形状・フットプリント) — 相違点: Package, Bandwidth, Mounting Type, Pin Count, Slew Rate.
OPA633KPG4
✅ ドロップイン📋 参考代替品(カタログ未掲載)
OPA633KP-BI
✅ ドロップイン📋 参考代替品(カタログ未掲載)
OPA633PA
✅ ドロップイン ⚠️ 仕様未検証📋 参考代替品(カタログ未掲載)
OPA551UA/2K5
✅ ドロップイン価格はお問い合わせください
データシートを見る →AD815AY
✅ ドロップイン価格はお問い合わせください
データシートを見る →OPA633KP 最大定格&電気的特性
| Product Type | High-speed unity-gain buffer amplifier |
| Number of Circuits | 1 circuit |
| Gain | 1 unity gain |
| Bandwidth | 260 MHz |
| Slew Rate | 2500 V/µs |
| Output Current | 100 mA |
| Offset Voltage | 1.5 mV |
| Supply Voltage Range | ±5 V to ±16 V |
| パッケージ | 8-pin through-hole DIP |
| ピン数 | 8 pins |
| 実装タイプ | Through-hole |
OPA633KP 8-pin through-hole dip ピン配置ガイド
OPA633KP (8-pin through-hole dip パッケージ) のピン配置。 このアナログコンポーネントは、入力、出力、および電源ピンを備えています。オフセットナル、補償、イネーブルピンの設定については、メーカーのデータシートを参照してください。信号調整やアンプ回路に最適です。
詳細なピン配置データはありません: OPA633KP.
詳細は データシート をご参照ください。
主な用途
OPA633KP の用途: 6 件s: Video Signal Buffering, ADC Input Conditioning, Operational-Amplifier Current Boosting, High-Speed Line Driver, Precision Measurement Instrumentation, Video Test and Measurement.
Video Signal Buffering
OPA633KP is well suited to video buffering because its 260 MHz bandwidth and 2500 V/µs slew rate preserve rapid transitions through video source and monitor stages. The unity-gain buffer adds drive capability without intentionally changing the voltage gain, while its 100 mA output current can drive downstream cables and termination networks more effectively than a conventional precision amplifier. Use it between a video source and a coax or PCB transmission line, accounting for the source and load impedances. Keep the signal route short, provide local supply bypassing, and verify settling because cable capacitance and long traces can affect the stability of any very-high-bandwidth output stage.
おすすめ
ADC Input Conditioning
OPA633KP can provide a low-impedance drive path into a high-speed analog-to-digital converter. Its 260 MHz bandwidth comfortably accommodates signals well above many converter sampling frequencies, while the 100 mA output capability helps charge the converter’s sampling network. Position the buffer directly ahead of the ADC input and keep the route short to minimize added capacitance and reflection. The amplifier must still settle to the ADC’s required accuracy within the acquisition interval, and the actual settling behavior should be checked with the ADC’s recommended input network. The 1.5 mV listed offset is also relevant when low-level sensor signals are converted.
おすすめ
Operational-Amplifier Current Boosting
OPA633KP can be placed in a feedback loop to increase the output-current capability of a conventional voltage-feedback amplifier. Its 260 MHz bandwidth and 2500 V/µs slew rate provide a fast unity-gain buffer stage, while the 100 mA output current is suited to driving heavier loads than many general-purpose amplifiers can handle. In this topology, stability depends on the host amplifier, loop compensation, output impedance, and load, so the manufacturer application guidance should be followed carefully. Keep the composite loop compact and avoid routing the high-current output over long PCB paths. The combined stage can serve instrumentation and video systems where load drive is more important than additional voltage gain.
おすすめ
High-Speed Line Driver
OPA633KP is applicable to line-driving circuits because its 2500 V/µs slew rate and 100 mA output current support fast edges into terminated lines. The 260 MHz bandwidth preserves high-frequency signal content, making the buffer useful in communications test equipment, instrumentation, and short-distance high-speed links. The load impedance, line length, connector, and termination method strongly influence the usable bandwidth; the listed 260 MHz figure should not be interpreted as an unlimited cable-distance specification. Use controlled-impedance routing where appropriate, keep the output return path continuous, and verify reflections and overshoot with the complete board and cable assembly.
おすすめ
Precision Measurement Instrumentation
OPA633KP can buffer sensor and measurement signals when the source impedance is too high for an ADC or subsequent analog stage. The 100 mA output capability helps isolate the source from downstream loading, and the 1.5 mV listed offset establishes the device’s low-frequency error contribution. For high-accuracy measurements, offset, bias current, noise, settling behavior, and thermal effects must be considered together rather than relying only on bandwidth. The buffer’s ±5 V to ±16 V supply range supports common dual-rail laboratory systems. Place it near the measurement input, use a low-noise ground implementation, and evaluate input bias current against the source impedance before finalizing the front end.
おすすめ
Video Test and Measurement
OPA633KP is suitable for the output buffers used in video test equipment, waveform generators, and monitor-interface circuits. Its 260 MHz bandwidth accommodates a broad range of analog video and general-purpose high-speed signal tests, while the 2500 V/µs slew rate reduces edge-rate limitation. The unity-gain configuration simplifies signal-path design and avoids relying on external feedback components. The output stage must still remain stable with the intended cable, connector, and termination; excessive capacitance or inductance can create ringing or oscillation. Use short output routing, a continuous return plane, and local bypass capacitors, then validate overshoot and settling with the complete fixture rather than only at the IC pins.
おすすめ
おすすめ製品の概要
エンジニアリング参考データ: OPA633KP — 比較、設計ガイダンス、コンプライアンス情報。
選定ガイド
代替品との比較
| パラメータ | この製品 | OPA633KPG4 | OPA633KP-BI | OPA633PA | OPA551 | AD815 |
|---|---|---|---|---|---|---|
| Package | 8-pin through-hole DIP | 8-pin through-hole DIP | 8-pin through-hole DIP | 8-pin through-hole DIP | 8-pin through-hole DIP | 8-pin through-hole DIP |
| Brand | Texas Instruments | Texas Instruments | Texas Instruments | Texas Instruments | Analog Devices | Analog Devices |
| Product Type | High-speed unity-gain buffer amplifier | High-speed unity-gain buffer amplifier | High-speed unity-gain buffer amplifier | High-speed unity-gain buffer amplifier | High-speed buffer amplifier | High-speed buffer amplifier |
| Bandwidth | 260 MHz | 260 MHz | 260 MHz | 260 MHz | Approximately 200 MHz | Approximately 190 MHz |
| Circuit Count | 1 circuit | 1 circuit | 1 circuit | 1 circuit | 1 circuit | 1 circuit |
主な差別化要因
- Higher bandwidth than the cross-brand 8-pin DIP candidates (vs AD815)
- Faster edge rate than the available cross-brand buffer comparison (vs OPA551)
- Purpose-built unity-gain buffer function (vs AD815)
設計ノート
Place the input, output, and supply connections using short, direct routes on the PCB. High-speed signals should not share long traces with unrelated analog channels, and the output path should avoid crossing splits in the ground plane. Keep the OPA633KP close to the driven circuit so that parasitic inductance and capacitance do not degrade the usable response of the 260 MHz amplifier.
Connect the positive and negative supply rails close to their respective package pins and place suitable bypass capacitors at the device. The OPA633KP is specified for ±5 V to ±16 V supplies, but decoupling requirements depend on the source impedance and trace inductance. Verify the supply rails for adequate current capability and low noise, particularly when the 100 mA output rating is approached.
Do not substitute a general-purpose operational amplifier solely because its bandwidth is adequate. A buffer must also remain stable at unity gain with the actual source and load, including cable and ADC capacitance. Check the OPA633 pin functions in the manufacturer datasheet, preserve the intended unity-gain topology, and confirm that any replacement provides equivalent supply limits, output-current capability, and pin functions.
The 2500 V/µs slew rate creates fast edges that can expose ringing, reflection, and ground-bounce problems. Use controlled-impedance routing for high-speed interconnects, terminate lines according to the system design, and keep the output return path continuous. Probe the completed assembly with the intended load because a clean waveform at the device pins does not guarantee acceptable behavior at the far end of a cable or connector.
コンプライアンス情報
The component is a commercial high-speed analog buffer amplifier. Specific RoHS, REACH, lead-free, halogen-free, and conflict-minerals declarations were not identified in the referenced product material.