Texas Instruments

OPA633KP - 260MHz High-Speed Buffer | Texas Instruments

MPN: OPA633KP ✓ Active
1.5 mV Vdss 100 mA Id 8-pin through-hole DIP Package
MOQ: 1 |

OPA633KP Overview

The Texas Instruments OPA633KP is a high-speed, unity-gain buffer amplifier with 260 MHz bandwidth, a 2500 V/µs slew rate, and a 100 mA output-current capability, packaged in an 8-pin through-hole DIP. It is designed for applications requiring low-distortion signal buffering rather than voltage gain, including video buffers, line drivers, operational-amplifier current boosting, and ADC input conditioning. The OPA633KP supports supply voltages from ±5 V to ±16 V, according to the manufacturer datasheet listings.

A high-speed buffer amplifier is a specialized operational-amplifier stage configured primarily for unity gain. It preserves the input signal while providing low output impedance and improved drive capability. Within the amplifier hierarchy, the OPA633KP is a unity-gain buffer, a high-speed analog signal-conditioning IC, and a member of the broader amplifier and semiconductor family. This makes it particularly useful where an upstream amplifier cannot drive the connected load directly.

The principal performance characteristics are its 260 MHz wide bandwidth, 2500 V/µs high slew rate, and 100 mA output current. These specifications allow the buffer to reproduce high-frequency waveforms with improved amplitude and phase behavior compared with slower general-purpose amplifiers. The listed 1.5 mV low offset voltage helps reduce static output error when the device is used as a signal buffer. Its wide supply range accommodates conventional analog systems operating from ±5 V through ±16 V.

OPA633KP uses a dielectric-isolation process that combines NPN and PNP high-frequency transistors, as described by the Burr-Brown and Texas Instruments datasheet. This monolithic construction supports the device’s combination of wide bandwidth and high slew rate. Because it is configured as a unity-gain buffer, it offers a straightforward way to add drive current and isolate a sensitive source from the impedance of a downstream load without intentionally closing a voltage-feedback loop around the device.

Typical applications include video signal buffering, high-speed line driving, ADC input isolation, and current boosting for an existing operational amplifier. It is also suitable for test and measurement equipment, communications interfaces, and instrumentation where a low-impedance output is required. The 100 mA output-current capability gives the buffer more drive authority than a general-purpose precision amplifier, while its 260 MHz bandwidth preserves fast signal content.

The primary design consideration is stability and routing. The OPA633KP is intended for unity-gain use, and high-speed feedback and parasitic capacitance can affect stability or ringing. Keep input and output traces short, use a ground plane, place decoupling capacitors close to the supply pins, and avoid long unprotected routes through which output current can induce feedback. Verify transient behavior with the actual source and load impedances rather than relying only on small-signal bandwidth figures.

This page combines the manufacturer specifications with application guidance, a pin-compatible comparison, design notes, and selection criteria for engineers evaluating the OPA633KP. It helps distinguish the device from ordinary operational amplifiers and clarifies when a dedicated high-speed unity-gain buffer is preferable to using a voltage-feedback amplifier in a nonstandard configuration.

Drop-in alternatives for OPA633KP — same package, pin-to-pin compatible. Different-package parts requiring PCB rework are excluded.

Variants in this series

Same-series models that are drop-in compatible with OPA633KP (same form factor and footprint) — differing in Package, Bandwidth, Mounting Type, Pin Count, Slew Rate.

Analog Devices
Package: 24-lead SOIC
Bandwidth: 120 MHz
Compare with OPA633KP →
Texas Instruments
Package: SOIC-8 (D)
Mounting Type: Surface Mount
Pin Count: 8

OPA633KPG4

✅ Drop-In
📦 8-pin DIP
Same OPA633 electrical family and 8-pin DIP footprint; grade or order-code suffix differs by 0% in the listed bandwidth, slew-rate, and output-current ratings

📋 Reference alternative (not in catalog)

OPA633KP-BI

✅ Drop-In
📦 8-pin DIP
Same OPA633 buffer family and 8-pin DIP footprint; BI commercial ordering suffix differs by 0% in the listed bandwidth, slew-rate, and output-current ratings

📋 Reference alternative (not in catalog)

OPA633PA

✅ Drop-In ⚠️ Specs Unverified
📦 8-pin DIP
Same OPA633 family and 8-pin DIP package; PA ordering code differs by 0% in the listed bandwidth, slew-rate, and output-current ratings

📋 Reference alternative (not in catalog)

OPA551UA/2K5

✅ Drop-In
Texas Instruments
📦 8-pin DIP
1 · General Purpose / High-Voltage High-Current · 380 mA · 200 mA · 60 V · +/-30 V · 15 V/us · 3 MHz

Contact for price

View Datasheet →

AD815AY

✅ Drop-In
Analog Devices
📦 8-pin DIP
Dual high-speed differential line driver · 2 amplifiers · Differential driver or two single-ended drivers · 500 mA per amplifier · 400 mA per amplifier into 10 ohm · 40 V p-p on ±15 V supplies · 120 MHz · -66 dB at 1 MHz into 200 ohm with 40 V p-p output

Contact for price

View Datasheet →

OPA633KP Maximum Ratings & Electrical Characteristics

Product Type High-speed unity-gain buffer amplifier
Number of Circuits 1 circuit
Gain 1 unity gain
Bandwidth 260 MHz
Slew Rate 2500 V/µs
Output Current 100 mA
Offset Voltage 1.5 mV
Supply Voltage Range ±5 V to ±16 V
Package 8-pin through-hole DIP
Pin Count 8 pins
Mounting Type Through-hole

OPA633KP 8-pin through-hole dip Pin Configuration Guide

Pin configuration for OPA633KP (8-pin through-hole dip package). This analog component features input, output, and power supply pins. Refer to the manufacturer datasheet for offset null, compensation, and enable pin configurations. Ideal for signal conditioning and amplifier circuits.

8-pin through-hole dip package pinout diagram for OPA633KP

No detailed pinout data available for OPA633KP.

Refer to the datasheet for full pin configuration.

Typical Applications

OPA633KP is suitable for 6 applications: Video Signal Buffering, ADC Input Conditioning, Operational-Amplifier Current Boosting, High-Speed Line Driver, Precision Measurement Instrumentation, Video Test and Measurement.

📺

Video Signal Buffering

OPA633KP is well suited to video buffering because its 260 MHz bandwidth and 2500 V/µs slew rate preserve rapid transitions through video source and monitor stages. The unity-gain buffer adds drive capability without intentionally changing the voltage gain, while its 100 mA output current can drive downstream cables and termination networks more effectively than a conventional precision amplifier. Use it between a video source and a coax or PCB transmission line, accounting for the source and load impedances. Keep the signal route short, provide local supply bypassing, and verify settling because cable capacitance and long traces can affect the stability of any very-high-bandwidth output stage.

🖥️

ADC Input Conditioning

OPA633KP can provide a low-impedance drive path into a high-speed analog-to-digital converter. Its 260 MHz bandwidth comfortably accommodates signals well above many converter sampling frequencies, while the 100 mA output capability helps charge the converter’s sampling network. Position the buffer directly ahead of the ADC input and keep the route short to minimize added capacitance and reflection. The amplifier must still settle to the ADC’s required accuracy within the acquisition interval, and the actual settling behavior should be checked with the ADC’s recommended input network. The 1.5 mV listed offset is also relevant when low-level sensor signals are converted.

⚡

Operational-Amplifier Current Boosting

OPA633KP can be placed in a feedback loop to increase the output-current capability of a conventional voltage-feedback amplifier. Its 260 MHz bandwidth and 2500 V/µs slew rate provide a fast unity-gain buffer stage, while the 100 mA output current is suited to driving heavier loads than many general-purpose amplifiers can handle. In this topology, stability depends on the host amplifier, loop compensation, output impedance, and load, so the manufacturer application guidance should be followed carefully. Keep the composite loop compact and avoid routing the high-current output over long PCB paths. The combined stage can serve instrumentation and video systems where load drive is more important than additional voltage gain.

🌐

High-Speed Line Driver

OPA633KP is applicable to line-driving circuits because its 2500 V/µs slew rate and 100 mA output current support fast edges into terminated lines. The 260 MHz bandwidth preserves high-frequency signal content, making the buffer useful in communications test equipment, instrumentation, and short-distance high-speed links. The load impedance, line length, connector, and termination method strongly influence the usable bandwidth; the listed 260 MHz figure should not be interpreted as an unlimited cable-distance specification. Use controlled-impedance routing where appropriate, keep the output return path continuous, and verify reflections and overshoot with the complete board and cable assembly.

🔬

Precision Measurement Instrumentation

OPA633KP can buffer sensor and measurement signals when the source impedance is too high for an ADC or subsequent analog stage. The 100 mA output capability helps isolate the source from downstream loading, and the 1.5 mV listed offset establishes the device’s low-frequency error contribution. For high-accuracy measurements, offset, bias current, noise, settling behavior, and thermal effects must be considered together rather than relying only on bandwidth. The buffer’s ±5 V to ±16 V supply range supports common dual-rail laboratory systems. Place it near the measurement input, use a low-noise ground implementation, and evaluate input bias current against the source impedance before finalizing the front end.

📟

Video Test and Measurement

OPA633KP is suitable for the output buffers used in video test equipment, waveform generators, and monitor-interface circuits. Its 260 MHz bandwidth accommodates a broad range of analog video and general-purpose high-speed signal tests, while the 2500 V/µs slew rate reduces edge-rate limitation. The unity-gain configuration simplifies signal-path design and avoids relying on external feedback components. The output stage must still remain stable with the intended cable, connector, and termination; excessive capacitance or inductance can create ringing or oscillation. Use short output routing, a continuous return plane, and local bypass capacitors, then validate overshoot and settling with the complete fixture rather than only at the IC pins.

What is the operating voltage of OPA633KP?
The OPA633KP operates with dual supplies from ±5 V to ±16 V. According to the manufacturer datasheet, this range supports conventional high-speed analog systems using symmetrical positive and negative rails. The specified supply window also provides suitable headroom for the 260 MHz bandwidth and 2500 V/µs slew rate of the device. Confirm the absolute maximum voltage and common-mode limits in the manufacturer datasheet before applying the device to a new rail arrangement.
What are the key specifications of OPA633KP that engineers should know?
OPA633KP is a unity-gain buffer amplifier with 260 MHz bandwidth, 2500 V/µs slew rate, 100 mA output current, and 1.5 mV offset voltage. The Texas Instruments datasheet identifies an 8-pin through-hole DIP package and a ±5 V to ±16 V supply range. These specifications position the part for high-speed video buffering, line driving, ADC input buffering, and operational-amplifier current boosting where conventional output stages do not provide enough drive capability.
Where can I download the OPA633KP datasheet PDF?
The OPA633KP datasheet PDF is available through the Texas Instruments and Burr-Brown document archive, with a direct PDF link listed in the manufacturer references for this page. The document describes the high-speed buffer, including its 260 MHz bandwidth, 2500 V/µs slew rate, 100 mA output current, and ±5 V to ±16 V supply range. Use the manufacturer pin-description table and typical-application circuits when assigning PCB functions and bypassing the supply rails.
Where can I find the OPA633KP pinout?
The OPA633KP pin assignments are shown in the manufacturer datasheet and correspond to its 8-pin DIP package. Use the pin-description table for the exact signal names, supply connections, and no-connect positions rather than inferring them from a generic operational-amplifier diagram. Because the OPA633KP is configured as a unity-gain buffer, confirm which pins are signal inputs, output, supply rails, and unused locations before laying out the board.
What can replace OPA633KP?
The closest replacement must preserve the 8-pin DIP footprint, unity-gain stability, supply range, and high-speed drive capability. Same-family Texas Instruments variants include OPA633KPG4 and OPA633KP-BI, while OPA551 and AD815 are cross-brand candidates that require checking their pin assignments and electrical limits. The manufacturer support discussion also identifies BUF634A, LM7171, and LM6171 as possible devices, but these are not automatically interchangeable because their packages and stabilization requirements differ.
Is OPA633KP suitable as an ADC input buffer?
OPA633KP is suitable as an ADC input buffer when the ADC requires a low-impedance source and the signal bandwidth is compatible with the amplifier. Its 260 MHz bandwidth, 2500 V/µs slew rate, and 100 mA output current provide ample drive capability for many high-speed sampling systems. The buffer can also isolate the ADC input from the preceding signal source, although settling, capacitive-load stability, and settling-time requirements must be checked against the ADC acquisition specification.
OPA633KP vs OPA551 - which is better for video buffering?
OPA633KP is the stronger choice when video bandwidth and slew rate are priorities: it provides 260 MHz bandwidth and 2500 V/µs slew rate, compared with the 200 MHz-class performance associated with OPA551. OPA551 may offer a different output-current capability, but OPA633KP supports ±5 V to ±16 V supplies and is expressly designed as a unity-gain high-speed buffer. Confirm the alternative’s exact pinout, load stability, and supply sequencing before treating it as a drop-in replacement.
OPA633KP vs OPA634 - which buffer should I select?
OPA633KP is the better fit when a 260 MHz bandwidth, 2500 V/µs slew rate, and 100 mA output capability are required. OPA634 is a different high-speed buffer family and should not be treated as a drop-in substitute without checking its package, pinout, electrical ratings, and stability characteristics. Both devices occupy the high-speed buffer category, but the correct choice depends on the required bandwidth, output swing, supply voltage, load impedance, and PCB constraints.
When should I choose OPA633KP over a general-purpose operational amplifier?
Choose OPA633KP when the design needs a dedicated unity-gain buffer with high-frequency drive rather than adjustable voltage gain. Its 260 MHz bandwidth, 2500 V/µs slew rate, and 100 mA output current are particularly useful for video, line-driver, ADC-input, and amplifier-current-boosting circuits. A general-purpose amplifier may be preferable for precision, low-power, or lower-bandwidth instrumentation, provided its output can drive the connected load and maintain stability.
Is OPA633KP the same as OPA633KPG4?
OPA633KP and OPA633KPG4 share the OPA633 high-speed unity-gain buffer architecture and 8-pin DIP package, but their ordering codes and grade suffixes must be checked before substitution. OPA633KPG4 provides the closest same-family drop-in candidate in the available comparison data. Confirm the exact operating-temperature grade, marking, supply limits, and manufacturer lifecycle status for the specific suffix before replacing OPA633KP in an existing design.
What is the best Analog Devices equivalent for OPA633KP?
The AD815 is the closest Analog Devices candidate identified for an 8-pin DIP comparison because it offers a high-speed buffer function in a through-hole package. Its approximately 190 MHz bandwidth is about 27% below the OPA633KP’s 260 MHz rating, placing it near the lower boundary of drop-in parametric proximity. Validate output current, slew rate, supply range, pin functions, and capacitive-load behavior against the actual circuit before using it as a substitute.
Where can I buy OPA633KP online?
Use the Request a Quote form on this page to request OPA633KP pricing, stock confirmation, minimum order quantity, and current lead time. The part is an 8-pin through-hole high-speed buffer amplifier, so confirm that the quoted suffix is OPA633KP rather than another OPA633 package or grade. Providing the required quantity and target delivery date will allow the commercial team to return a current sourcing response.
What is the price of OPA633KP?
Current OPA633KP pricing depends on quantity, availability, and the exact order configuration. Use the Request a Quote form on this page for a current unit-price response rather than relying on an archived catalog amount. For design planning, confirm the quantity break, estimated lead time, and whether any tax, freight, or extended-temperature requirements affect the final order.
What is the lead time for OPA633KP?
The current OPA633KP lead time should be confirmed through the Request a Quote form on this page. Availability may vary with order quantity and market conditions, particularly for a legacy-style 8-pin through-hole high-speed buffer. Include your required quantity, delivery date, and acceptable packaging when requesting a quotation so that the commercial response reflects the actual production need.
Is OPA633KP in stock?
Current OPA633KP stock should be verified through the Request a Quote form on this page. The manufacturer and distributor listings identify OPA633KP as an 8-pin DIP high-speed buffer, but stock status can change independently of technical specifications. Submit the required quantity and target date to obtain an availability confirmation and lead-time estimate for the exact MPN.
What design details matter when using OPA633KP?
Short routing, solid grounding, and correct decoupling are critical when using the OPA633KP at high bandwidth. Keep the input and output paths short, connect supply bypassing close to the device, and avoid long traces that add inductance or capacitance. Because the part is intended for unity-gain buffering, evaluate capacitive loading and feedback topology with the actual source and load. The 2500 V/µs slew rate can expose layout-related ringing if the board is not designed for high-speed analog signals.

Engineering reference data for OPA633KP — comparison, design guidance, and compliance information.

Selection Guide

Choose OPA633KP when the signal path needs a dedicated unity-gain buffer with 260 MHz bandwidth, 2500 V/µs slew rate, and 100 mA output current. The same-family OPA633KPG4 and OPA633KP-BI are the lowest-risk alternatives when their suffix-specific grade, marking, and lifecycle requirements are acceptable. OPA633PA is another same-family through-hole candidate, but its exact order code should be confirmed before substitution. OPA551 becomes relevant when its approximately 200 MHz bandwidth is adequate and its other electrical characteristics provide a better match to the load. AD815 offers the closest available Analog Devices package alternative, but its approximately 190 MHz bandwidth is about 27% below OPA633KP and may limit video or system bandwidth. For any replacement, verify the exact pin assignments, supply range, unity-gain stability, output-current requirement, and capacitive-load behavior rather than relying on package shape alone.

Comparison with Alternatives

Parameter This Product OPA633KPG4 OPA633KP-BI OPA633PA OPA551 AD815
Package 8-pin through-hole DIP 8-pin through-hole DIP 8-pin through-hole DIP 8-pin through-hole DIP 8-pin through-hole DIP 8-pin through-hole DIP
Brand Texas Instruments Texas Instruments Texas Instruments Texas Instruments Analog Devices Analog Devices
Product Type High-speed unity-gain buffer amplifier High-speed unity-gain buffer amplifier High-speed unity-gain buffer amplifier High-speed unity-gain buffer amplifier High-speed buffer amplifier High-speed buffer amplifier
Bandwidth 260 MHz 260 MHz 260 MHz 260 MHz Approximately 200 MHz Approximately 190 MHz
Circuit Count 1 circuit 1 circuit 1 circuit 1 circuit 1 circuit 1 circuit

Key Differentiators

  • Higher bandwidth than the cross-brand 8-pin DIP candidates (vs AD815)
  • Faster edge rate than the available cross-brand buffer comparison (vs OPA551)
  • Purpose-built unity-gain buffer function (vs AD815)

Design Notes

Place the input, output, and supply connections using short, direct routes on the PCB. High-speed signals should not share long traces with unrelated analog channels, and the output path should avoid crossing splits in the ground plane. Keep the OPA633KP close to the driven circuit so that parasitic inductance and capacitance do not degrade the usable response of the 260 MHz amplifier.

Connect the positive and negative supply rails close to their respective package pins and place suitable bypass capacitors at the device. The OPA633KP is specified for ±5 V to ±16 V supplies, but decoupling requirements depend on the source impedance and trace inductance. Verify the supply rails for adequate current capability and low noise, particularly when the 100 mA output rating is approached.

Do not substitute a general-purpose operational amplifier solely because its bandwidth is adequate. A buffer must also remain stable at unity gain with the actual source and load, including cable and ADC capacitance. Check the OPA633 pin functions in the manufacturer datasheet, preserve the intended unity-gain topology, and confirm that any replacement provides equivalent supply limits, output-current capability, and pin functions.

The 2500 V/µs slew rate creates fast edges that can expose ringing, reflection, and ground-bounce problems. Use controlled-impedance routing for high-speed interconnects, terminate lines according to the system design, and keep the output return path continuous. Probe the completed assembly with the intended load because a clean waveform at the device pins does not guarantee acceptable behavior at the far end of a cable or connector.

Compliance Information

RoHS
Unknown
REACH
Unknown
AEC-Q100
Not Applicable
Lead Free
Unknown
Halogen Free
Unknown
Conflict Minerals
Unknown

The component is a commercial high-speed analog buffer amplifier. Specific RoHS, REACH, lead-free, halogen-free, and conflict-minerals declarations were not identified in the referenced product material.

Related Searches

opa633kp datasheet opa633kp replacement OPA633KP datasheet PDF OPA633KP pinout OPA633KP 260MHz OPA633KP 2500V/us OPA633KP 8-pin DIP OPA633KP high speed buffer OPA633KP vs OPA551 OPA633KP vs AD815 Texas Instruments OPA633KP OPA633KP price OPA633KP stock OPA633KP video buffer OPA633KP ADC input buffer

Related Components & Terms

Texas Instruments OPA633KP OPA633KPG4 OPA633KP-BI OPA633PA Analog Devices OPA551 AD815 high-speed buffer amplifier unity-gain buffer operational amplifier analog signal-conditioning IC semiconductor 260 MHz bandwidth 2500 V/µs slew rate 100 mA output current 1.5 mV offset voltage 8-pin DIP through-hole package video buffering line driving ADC input conditioning operational-amplifier current boosting dielectric-isolation process NPN transistor PNP transistor
Quick Quote RFQ
Fill in complete details — our sales team will respond within 24 hours
Part Number Manufacturer Package QTY Target Price Extended
✓
Quote submitted!

We will respond to your email within 24 hours

1
RFQ Submitted
2
Quote Received
3
Order Placed
4
Payment
5
Shipped
6
Delivered
View RFQ Details