PEX8608-BA50BC - 8-Lane Gen 2 PCIe Switch | Broadcom
部品番号: PEX8608-BA50BC ✓ 生産中PEX8608-BA50BC 概要
A PCI Express switch is a semiconductor that routes high-speed serial transactions between a host or upstream endpoint and multiple downstream devices. Within the PCI Express hierarchy, this device is a PCIe switch, a fabric-based interface IC, and a system-level connectivity component. Eight SerDes lanes can be partitioned among several ports, allowing one compact system to aggregate endpoints for communications, control-plane, embedded, storage, and peer-to-peer equipment.
The PEX 8608 provides non-blocking internal switching, two virtual channels for traffic prioritization, and full line-rate operation on configured ports. Broadcom describes packet cut-through latency as 140 ns for an x4-to-x1 configuration in its product-page summary and as up to 130 ns in the linked feature documentation. SerDes outputs can be software-controlled for power reduction and signal-strength optimization.
Power management follows the PCI Express power-management specification. Unused SerDes physical links can be switched off to reduce power consumption, while controllable SerDes outputs allow system software to tune operating conditions. The switch architecture supports flexible port configurations, virtual-channel traffic separation, and scalable aggregation without relying on an external switch fabric for each endpoint connection.
Typical deployments include communications platforms, embedded systems, backplane aggregation, industrial controllers, test equipment, and servers that need additional PCIe endpoints. The eight-port capability makes it useful where several endpoint types, link widths, or downstream devices must share a compact host interface while retaining deterministic low-latency routing.
Design the PCB with the manufacturer’s 196-PBGA land pattern, high-speed differential routing rules, reference-plane continuity, and decoupling recommendations. Validate lane configuration, firmware or register programming, auxiliary power sequencing, and thermal performance across the intended traffic profile before production release. The exact pin assignments and electrical limits must be taken from the pin-description table in the manufacturer datasheet.
This page consolidates the official product architecture, package information, Gen 2 link capability, application fit, and practical implementation considerations. It also distinguishes confirmed drop-in coverage from broad functional equivalents, helping engineers determine whether a candidate can be soldered onto the same PCB land pattern rather than merely serving a similar PCIe-switch function.
ドロップイン代替品: PEX8608-BA50BC — 同一パッケージでピン互換。PCBの作り直しが必要な異なるパッケージの部品は除外されています。
PEX8608-BA50BC-G
✅ ドロップイン📋 参考代替品(カタログ未掲載)
PEX8608-BA50BC 最大定格&電気的特性
| Product Type | PCI Express switch IC |
| PCI Express Generation | Gen 2 |
| Maximum Data Rate | 5.0 GT/s |
| PCIe Lane Count | 8 lanes |
| Maximum Configurable Port Count | 8 ports |
| PCI Express Base Specification | Revision 2.0 |
| Packet Cut-Through Latency | 140 ns for x4-to-x1 configuration |
| Documented Maximum Cut-Through Latency | 130 ns for x4-to-x1 configuration |
| Virtual Channels | 2 |
| Internal Switching | Non-blocking |
| Power Management | PCI Express power-management specification compliant |
| SerDes Link Control | Software-controlled outputs and unused-link shutdown |
| パッケージ | 196-PBGA, 15 x 15 mm |
| 実装タイプ | Surface mount |
PEX8608-BA50BC 196-pbga, 15 x 15 mm ピン配置ガイド
PEX8608-BA50BC (196-pbga, 15 x 15 mm パッケージ) のピン配置。 このアナログコンポーネントは、入力、出力、および電源ピンを備えています。オフセットナル、補償、イネーブルピンの設定については、メーカーのデータシートを参照してください。信号調整やアンプ回路に最適です。
詳細なピン配置データはありません: PEX8608-BA50BC.
詳細は データシート をご参照ください。
主な用途
PEX8608-BA50BC の用途: 3 件s: 信号コンディショニング, データ収集, オーディオ処理.
信号コンディショニング
PEX8608-BA50BCを使用したセンサー信号の増幅とフィルタリング。
データ収集
PEX8608-BA50BCによるデジタル処理用のアナログ信号変換。
オーディオ処理
PEX8608-BA50BCによるオーディオ信号の増幅と処理。
エンジニアリング参考データ: PEX8608-BA50BC — 比較、設計ガイダンス、コンプライアンス情報。
選定ガイド
代替品との比較
| パラメータ | この製品 | PEX8608-BA50BC-G |
|---|---|---|
| Package | 196-PBGA (15 x 15 mm) | 196-PBGA (15 x 15 mm) |
| Brand | Broadcom | Broadcom |
| PCIe Generation | Gen 2 | Gen 2 |
| Maximum Data Rate | 5.0 GT/s | 5.0 GT/s |
| Lane Count | 8 lanes | 8 lanes |
| Maximum Port Count | 8 flexible ports | 8 flexible ports |
| Packet Cut-Through Latency | 140 ns for x4-to-x1 configuration | 140 ns for x4-to-x1 configuration |
| Virtual Channels | 2 | 2 |
| Internal Switching | Non-blocking | Non-blocking |
| SerDes Control | Software-controlled outputs with unused-link shutdown | Software-controlled outputs with unused-link shutdown |
主な差別化要因
- Eight flexible PCIe lanes in one switch (vs PEX8718)
- Packet cut-through for low-latency routing (vs PEX8608-BA50BC-G)
- Software-controlled SerDes power optimization (vs PEX8718)
設計ノート
Route all PCIe differential pairs as impedance-controlled, length-matched transmission lines with continuous reference planes. Place the transceiver and bypass components according to the manufacturer’s reference circuit and layout guidance, minimize stub branches, and avoid routing high-speed links across plane splits. Validate the final 196-BGA escape fanout with the PCB manufacturer’s fine-pitch assembly capability.
Separate each supply domain and follow the manufacturer’s recommended startup, decoupling, and auxiliary-power sequencing. Place the required high-frequency capacitors close to their associated power and ground balls, and maintain low-impedance planes from the package to the supply network. Power-domain sequencing must also satisfy every downstream endpoint because an incorrectly ordered auxiliary rail can prevent the switch from enumerating reliably.
Configure lane widths only after confirming the complete point-to-point link budget from the upstream host through the PEX 8608 to each downstream endpoint. Use the manufacturer’s SerDes configuration procedure, test masks, and compliance constraints during validation. Perform insertion-loss, return-loss, jitter, eye-diagram, and receiver-margin checks on every production board configuration rather than relying only on simulation.
Estimate total switch dissipation from the operating lane count, width, traffic activity, voltage, and enabled SerDes links, then compare the resulting junction-temperature margin with the package and board construction. The available materials do not state the complete electrical and thermal limits, so obtain the detailed specifications before defining copper area, airflow, or adjacent-component placement requirements.
Do not substitute a PCIe switch based only on lane count or advertised aggregate bandwidth. Confirm the package land pattern, every power and ground ball, lane polarity, reference-clock requirements, configuration interface, register behavior, and reset or startup sequence. The PEX8718, for example, is not pin-for-pin or firmware compatible because its architecture, register map, and configuration interfaces differ.
コンプライアンス情報
No explicit compliance declarations were found for this ordering code. Confirm material and environmental status with Broadcom before release.