PEX8608-BA50BC - 8-Lane Gen 2 PCIe Switch | Broadcom
MPN: PEX8608-BA50BC ✓ Hoạt độngPEX8608-BA50BC Tóm tắt
A PCI Express switch is a semiconductor that routes high-speed serial transactions between a host or upstream endpoint and multiple downstream devices. Within the PCI Express hierarchy, this device is a PCIe switch, a fabric-based interface IC, and a system-level connectivity component. Eight SerDes lanes can be partitioned among several ports, allowing one compact system to aggregate endpoints for communications, control-plane, embedded, storage, and peer-to-peer equipment.
The PEX 8608 provides non-blocking internal switching, two virtual channels for traffic prioritization, and full line-rate operation on configured ports. Broadcom describes packet cut-through latency as 140 ns for an x4-to-x1 configuration in its product-page summary and as up to 130 ns in the linked feature documentation. SerDes outputs can be software-controlled for power reduction and signal-strength optimization.
Power management follows the PCI Express power-management specification. Unused SerDes physical links can be switched off to reduce power consumption, while controllable SerDes outputs allow system software to tune operating conditions. The switch architecture supports flexible port configurations, virtual-channel traffic separation, and scalable aggregation without relying on an external switch fabric for each endpoint connection.
Typical deployments include communications platforms, embedded systems, backplane aggregation, industrial controllers, test equipment, and servers that need additional PCIe endpoints. The eight-port capability makes it useful where several endpoint types, link widths, or downstream devices must share a compact host interface while retaining deterministic low-latency routing.
Design the PCB with the manufacturer’s 196-PBGA land pattern, high-speed differential routing rules, reference-plane continuity, and decoupling recommendations. Validate lane configuration, firmware or register programming, auxiliary power sequencing, and thermal performance across the intended traffic profile before production release. The exact pin assignments and electrical limits must be taken from the pin-description table in the manufacturer datasheet.
This page consolidates the official product architecture, package information, Gen 2 link capability, application fit, and practical implementation considerations. It also distinguishes confirmed drop-in coverage from broad functional equivalents, helping engineers determine whether a candidate can be soldered onto the same PCB land pattern rather than merely serving a similar PCIe-switch function.
Bộ thay thế dễ dàng lắp đặt cho PEX8608-BA50BC — cùng gói, chân-to-chân tương thích. Các bộ phận yêu cầu hàn PCB bị loại trừ.
PEX8608-BA50BC-G
✅ Drop-In📋 Tham chiếu thay thế (không có trong danh mục)
PEX8608-BA50BC Tỷ lệ tối đa & tính chất điện
| Product Type | PCI Express switch IC |
| PCI Express Generation | Gen 2 |
| Maximum Data Rate | 5.0 GT/s |
| PCIe Lane Count | 8 lanes |
| Maximum Configurable Port Count | 8 ports |
| PCI Express Base Specification | Revision 2.0 |
| Packet Cut-Through Latency | 140 ns for x4-to-x1 configuration |
| Documented Maximum Cut-Through Latency | 130 ns for x4-to-x1 configuration |
| Virtual Channels | 2 |
| Internal Switching | Non-blocking |
| Power Management | PCI Express power-management specification compliant |
| SerDes Link Control | Software-controlled outputs and unused-link shutdown |
| Hộp | 196-PBGA, 15 x 15 mm |
| Kiểu lắp đặt | Surface mount |
Hướng dẫn cấu hình chân PEX8608-BA50BC 196-pbga, 15 x 15 mm
Cấu hình chân cho PEX8608-BA50BC (196-pbga, 15 x 15 mm gói). Thành phần số hiệu này có chân đầu vào, đầu ra và nguồn cung cấp. Tham khảo tài liệu thông số kỹ thuật của nhà sản xuất để biết cấu hình chân bù, bù trừ và chân kích hoạt. Hoàn hảo cho điều kiện tín hiệu và mạch khuếch đại.
Không có dữ liệu chân cụ thể sẵn có cho PEX8608-BA50BC.
Tham khảo: tài liệu kỹ thuật cho cấu hình chân đầy đủ.
Ứng dụng tiêu biểu
PEX8608-BA50BC phù hợp cho 3 Áp dụngs: Điều kiện tín hiệu, Thiết bị thu thập dữ liệu, Xử lý âm thanh.
Điều kiện tín hiệu
Phân tích và lọc tín hiệu cảm biến sử dụng PEX8608-BA50BC.
Thiết bị thu thập dữ liệu
Chuyển đổi tín hiệu tương tự thành quá trình số sử dụng PEX8608-BA50BC.
Xử lý âm thanh
Phân tích và khuếch đại tín hiệu âm thanh sử dụng PEX8608-BA50BC.
Dữ liệu tham khảo kỹ thuật cho PEX8608-BA50BC — so sánh, hướng dẫn thiết kế và thông tin tuân thủ.
Hướng dẫn chọn lựa
So sánh với các sản phẩm thay thế
| Tham số | Sản phẩm này | PEX8608-BA50BC-G |
|---|---|---|
| Package | 196-PBGA (15 x 15 mm) | 196-PBGA (15 x 15 mm) |
| Brand | Broadcom | Broadcom |
| PCIe Generation | Gen 2 | Gen 2 |
| Maximum Data Rate | 5.0 GT/s | 5.0 GT/s |
| Lane Count | 8 lanes | 8 lanes |
| Maximum Port Count | 8 flexible ports | 8 flexible ports |
| Packet Cut-Through Latency | 140 ns for x4-to-x1 configuration | 140 ns for x4-to-x1 configuration |
| Virtual Channels | 2 | 2 |
| Internal Switching | Non-blocking | Non-blocking |
| SerDes Control | Software-controlled outputs with unused-link shutdown | Software-controlled outputs with unused-link shutdown |
Bảo phân biệt quan trọng
- Eight flexible PCIe lanes in one switch (vsPEX8718)
- Packet cut-through for low-latency routing (vsPEX8608-BA50BC-G)
- Software-controlled SerDes power optimization (vsPEX8718)
Ghi chú thiết kế
Route all PCIe differential pairs as impedance-controlled, length-matched transmission lines with continuous reference planes. Place the transceiver and bypass components according to the manufacturer’s reference circuit and layout guidance, minimize stub branches, and avoid routing high-speed links across plane splits. Validate the final 196-BGA escape fanout with the PCB manufacturer’s fine-pitch assembly capability.
Separate each supply domain and follow the manufacturer’s recommended startup, decoupling, and auxiliary-power sequencing. Place the required high-frequency capacitors close to their associated power and ground balls, and maintain low-impedance planes from the package to the supply network. Power-domain sequencing must also satisfy every downstream endpoint because an incorrectly ordered auxiliary rail can prevent the switch from enumerating reliably.
Configure lane widths only after confirming the complete point-to-point link budget from the upstream host through the PEX 8608 to each downstream endpoint. Use the manufacturer’s SerDes configuration procedure, test masks, and compliance constraints during validation. Perform insertion-loss, return-loss, jitter, eye-diagram, and receiver-margin checks on every production board configuration rather than relying only on simulation.
Estimate total switch dissipation from the operating lane count, width, traffic activity, voltage, and enabled SerDes links, then compare the resulting junction-temperature margin with the package and board construction. The available materials do not state the complete electrical and thermal limits, so obtain the detailed specifications before defining copper area, airflow, or adjacent-component placement requirements.
Do not substitute a PCIe switch based only on lane count or advertised aggregate bandwidth. Confirm the package land pattern, every power and ground ball, lane polarity, reference-clock requirements, configuration interface, register behavior, and reset or startup sequence. The PEX8718, for example, is not pin-for-pin or firmware compatible because its architecture, register map, and configuration interfaces differ.
Thông tin tuân thủ
No explicit compliance declarations were found for this ordering code. Confirm material and environmental status with Broadcom before release.