PEX8608-BA50BC - 8-Lane Gen 2 PCIe Switch | Broadcom
料号: PEX8608-BA50BC ✓ 量产中PEX8608-BA50BC 概述
A PCI Express switch is a semiconductor that routes high-speed serial transactions between a host or upstream endpoint and multiple downstream devices. Within the PCI Express hierarchy, this device is a PCIe switch, a fabric-based interface IC, and a system-level connectivity component. Eight SerDes lanes can be partitioned among several ports, allowing one compact system to aggregate endpoints for communications, control-plane, embedded, storage, and peer-to-peer equipment.
The PEX 8608 provides non-blocking internal switching, two virtual channels for traffic prioritization, and full line-rate operation on configured ports. Broadcom describes packet cut-through latency as 140 ns for an x4-to-x1 configuration in its product-page summary and as up to 130 ns in the linked feature documentation. SerDes outputs can be software-controlled for power reduction and signal-strength optimization.
Power management follows the PCI Express power-management specification. Unused SerDes physical links can be switched off to reduce power consumption, while controllable SerDes outputs allow system software to tune operating conditions. The switch architecture supports flexible port configurations, virtual-channel traffic separation, and scalable aggregation without relying on an external switch fabric for each endpoint connection.
Typical deployments include communications platforms, embedded systems, backplane aggregation, industrial controllers, test equipment, and servers that need additional PCIe endpoints. The eight-port capability makes it useful where several endpoint types, link widths, or downstream devices must share a compact host interface while retaining deterministic low-latency routing.
Design the PCB with the manufacturer’s 196-PBGA land pattern, high-speed differential routing rules, reference-plane continuity, and decoupling recommendations. Validate lane configuration, firmware or register programming, auxiliary power sequencing, and thermal performance across the intended traffic profile before production release. The exact pin assignments and electrical limits must be taken from the pin-description table in the manufacturer datasheet.
This page consolidates the official product architecture, package information, Gen 2 link capability, application fit, and practical implementation considerations. It also distinguishes confirmed drop-in coverage from broad functional equivalents, helping engineers determine whether a candidate can be soldered onto the same PCB land pattern rather than merely serving a similar PCIe-switch function.
直接替换替代料: PEX8608-BA50BC ——相同封装,引脚兼容。需要 PCB 改动的不同封装料号已排除。
PEX8608-BA50BC-G
✅ 直接替换📋 参考替代料(不在目录中)
PEX8608-BA50BC 最大额定值与电气特性
| Product Type | PCI Express switch IC |
| PCI Express Generation | Gen 2 |
| Maximum Data Rate | 5.0 GT/s |
| PCIe Lane Count | 8 lanes |
| Maximum Configurable Port Count | 8 ports |
| PCI Express Base Specification | Revision 2.0 |
| Packet Cut-Through Latency | 140 ns for x4-to-x1 configuration |
| Documented Maximum Cut-Through Latency | 130 ns for x4-to-x1 configuration |
| Virtual Channels | 2 |
| Internal Switching | Non-blocking |
| Power Management | PCI Express power-management specification compliant |
| SerDes Link Control | Software-controlled outputs and unused-link shutdown |
| 封装 | 196-PBGA, 15 x 15 mm |
| 安装类型 | Surface mount |
PEX8608-BA50BC 196-pbga, 15 x 15 mm 引脚配置指南
PEX8608-BA50BC(196-pbga, 15 x 15 mm 封装)的引脚配置。 该模拟元件具有输入、输出和电源引脚。请参阅制造商数据手册以了解失调调零、补偿和使能引脚配置。适用于信号调理和放大器电路。
暂无详细引脚数据: PEX8608-BA50BC.
请参阅 数据手册 以查看完整引脚配置。
典型应用
PEX8608-BA50BC 适用于 3 应用s: 信号调理, 数据采集, 音频处理.
信号调理
使用 PEX8608-BA50BC 放大和滤波传感器信号。
数据采集
使用 PEX8608-BA50BC 将模拟信号转换为数字信号进行处理。
音频处理
使用 PEX8608-BA50BC 进行音频信号放大和处理。
工程参考数据: PEX8608-BA50BC ——对比、设计指导和合规信息。
选型指南
与替代料对比
| 参数 | 本产品 | PEX8608-BA50BC-G |
|---|---|---|
| Package | 196-PBGA (15 x 15 mm) | 196-PBGA (15 x 15 mm) |
| Brand | Broadcom | Broadcom |
| PCIe Generation | Gen 2 | Gen 2 |
| Maximum Data Rate | 5.0 GT/s | 5.0 GT/s |
| Lane Count | 8 lanes | 8 lanes |
| Maximum Port Count | 8 flexible ports | 8 flexible ports |
| Packet Cut-Through Latency | 140 ns for x4-to-x1 configuration | 140 ns for x4-to-x1 configuration |
| Virtual Channels | 2 | 2 |
| Internal Switching | Non-blocking | Non-blocking |
| SerDes Control | Software-controlled outputs with unused-link shutdown | Software-controlled outputs with unused-link shutdown |
关键差异点
- Eight flexible PCIe lanes in one switch (对比 PEX8718)
- Packet cut-through for low-latency routing (对比 PEX8608-BA50BC-G)
- Software-controlled SerDes power optimization (对比 PEX8718)
设计说明
Route all PCIe differential pairs as impedance-controlled, length-matched transmission lines with continuous reference planes. Place the transceiver and bypass components according to the manufacturer’s reference circuit and layout guidance, minimize stub branches, and avoid routing high-speed links across plane splits. Validate the final 196-BGA escape fanout with the PCB manufacturer’s fine-pitch assembly capability.
Separate each supply domain and follow the manufacturer’s recommended startup, decoupling, and auxiliary-power sequencing. Place the required high-frequency capacitors close to their associated power and ground balls, and maintain low-impedance planes from the package to the supply network. Power-domain sequencing must also satisfy every downstream endpoint because an incorrectly ordered auxiliary rail can prevent the switch from enumerating reliably.
Configure lane widths only after confirming the complete point-to-point link budget from the upstream host through the PEX 8608 to each downstream endpoint. Use the manufacturer’s SerDes configuration procedure, test masks, and compliance constraints during validation. Perform insertion-loss, return-loss, jitter, eye-diagram, and receiver-margin checks on every production board configuration rather than relying only on simulation.
Estimate total switch dissipation from the operating lane count, width, traffic activity, voltage, and enabled SerDes links, then compare the resulting junction-temperature margin with the package and board construction. The available materials do not state the complete electrical and thermal limits, so obtain the detailed specifications before defining copper area, airflow, or adjacent-component placement requirements.
Do not substitute a PCIe switch based only on lane count or advertised aggregate bandwidth. Confirm the package land pattern, every power and ground ball, lane polarity, reference-clock requirements, configuration interface, register behavior, and reset or startup sequence. The PEX8718, for example, is not pin-for-pin or firmware compatible because its architecture, register map, and configuration interfaces differ.
合规信息
No explicit compliance declarations were found for this ordering code. Confirm material and environmental status with Broadcom before release.