PEX8608-BA50BC - 8-Lane Gen 2 PCIe Switch | Broadcom
MPN: PEX8608-BA50BC ✓ 啟用中PEX8608-BA50BC 概覽
A PCI Express switch is a semiconductor that routes high-speed serial transactions between a host or upstream endpoint and multiple downstream devices. Within the PCI Express hierarchy, this device is a PCIe switch, a fabric-based interface IC, and a system-level connectivity component. Eight SerDes lanes can be partitioned among several ports, allowing one compact system to aggregate endpoints for communications, control-plane, embedded, storage, and peer-to-peer equipment.
The PEX 8608 provides non-blocking internal switching, two virtual channels for traffic prioritization, and full line-rate operation on configured ports. Broadcom describes packet cut-through latency as 140 ns for an x4-to-x1 configuration in its product-page summary and as up to 130 ns in the linked feature documentation. SerDes outputs can be software-controlled for power reduction and signal-strength optimization.
Power management follows the PCI Express power-management specification. Unused SerDes physical links can be switched off to reduce power consumption, while controllable SerDes outputs allow system software to tune operating conditions. The switch architecture supports flexible port configurations, virtual-channel traffic separation, and scalable aggregation without relying on an external switch fabric for each endpoint connection.
Typical deployments include communications platforms, embedded systems, backplane aggregation, industrial controllers, test equipment, and servers that need additional PCIe endpoints. The eight-port capability makes it useful where several endpoint types, link widths, or downstream devices must share a compact host interface while retaining deterministic low-latency routing.
Design the PCB with the manufacturer’s 196-PBGA land pattern, high-speed differential routing rules, reference-plane continuity, and decoupling recommendations. Validate lane configuration, firmware or register programming, auxiliary power sequencing, and thermal performance across the intended traffic profile before production release. The exact pin assignments and electrical limits must be taken from the pin-description table in the manufacturer datasheet.
This page consolidates the official product architecture, package information, Gen 2 link capability, application fit, and practical implementation considerations. It also distinguishes confirmed drop-in coverage from broad functional equivalents, helping engineers determine whether a candidate can be soldered onto the same PCB land pattern rather than merely serving a similar PCIe-switch function.
直接替換替代品,適用於 PEX8608-BA50BC — 相同封裝,腳位對腳位相容。需重新設計 PCB 的不同封裝零件不列入。
PEX8608-BA50BC-G
✅ 直接替換📋 參考替代品(不在目錄中)
PEX8608-BA50BC 最大額定值與電氣特性
| Product Type | PCI Express switch IC |
| PCI Express Generation | Gen 2 |
| Maximum Data Rate | 5.0 GT/s |
| PCIe Lane Count | 8 lanes |
| Maximum Configurable Port Count | 8 ports |
| PCI Express Base Specification | Revision 2.0 |
| Packet Cut-Through Latency | 140 ns for x4-to-x1 configuration |
| Documented Maximum Cut-Through Latency | 130 ns for x4-to-x1 configuration |
| Virtual Channels | 2 |
| Internal Switching | Non-blocking |
| Power Management | PCI Express power-management specification compliant |
| SerDes Link Control | Software-controlled outputs and unused-link shutdown |
| 封裝 | 196-PBGA, 15 x 15 mm |
| 安裝類型 | Surface mount |
PEX8608-BA50BC 196-pbga, 15 x 15 mm 腳位配置指南
PEX8608-BA50BC(196-pbga, 15 x 15 mm 封裝)的腳位配置。 此類比元件具有輸入、輸出與電源腳位。偏移歸零、補償與致能腳位配置請參閱製造商資料表。適用於訊號調理與放大器電路。
無詳細腳位定義資料: PEX8608-BA50BC.
請參閱 資料表 以查看完整腳位配置。
典型應用
PEX8608-BA50BC 適用於 3 應用s: 訊號調理, 資料擷取, 音訊處理.
訊號調理
使用 PEX8608-BA50BC 放大與濾波感測器訊號。
資料擷取
使用 PEX8608-BA50BC 將類比訊號轉換以供數位處理。
音訊處理
使用 PEX8608-BA50BC 進行音訊訊號放大與處理。
工程參考資料,適用於 PEX8608-BA50BC — 比較、設計指引及合規資訊。
選型指南
與替代品比較
| 參數 | 本產品 | PEX8608-BA50BC-G |
|---|---|---|
| Package | 196-PBGA (15 x 15 mm) | 196-PBGA (15 x 15 mm) |
| Brand | Broadcom | Broadcom |
| PCIe Generation | Gen 2 | Gen 2 |
| Maximum Data Rate | 5.0 GT/s | 5.0 GT/s |
| Lane Count | 8 lanes | 8 lanes |
| Maximum Port Count | 8 flexible ports | 8 flexible ports |
| Packet Cut-Through Latency | 140 ns for x4-to-x1 configuration | 140 ns for x4-to-x1 configuration |
| Virtual Channels | 2 | 2 |
| Internal Switching | Non-blocking | Non-blocking |
| SerDes Control | Software-controlled outputs with unused-link shutdown | Software-controlled outputs with unused-link shutdown |
主要差異化特點
- Eight flexible PCIe lanes in one switch (對比PEX8718)
- Packet cut-through for low-latency routing (對比PEX8608-BA50BC-G)
- Software-controlled SerDes power optimization (對比PEX8718)
設計說明
Route all PCIe differential pairs as impedance-controlled, length-matched transmission lines with continuous reference planes. Place the transceiver and bypass components according to the manufacturer’s reference circuit and layout guidance, minimize stub branches, and avoid routing high-speed links across plane splits. Validate the final 196-BGA escape fanout with the PCB manufacturer’s fine-pitch assembly capability.
Separate each supply domain and follow the manufacturer’s recommended startup, decoupling, and auxiliary-power sequencing. Place the required high-frequency capacitors close to their associated power and ground balls, and maintain low-impedance planes from the package to the supply network. Power-domain sequencing must also satisfy every downstream endpoint because an incorrectly ordered auxiliary rail can prevent the switch from enumerating reliably.
Configure lane widths only after confirming the complete point-to-point link budget from the upstream host through the PEX 8608 to each downstream endpoint. Use the manufacturer’s SerDes configuration procedure, test masks, and compliance constraints during validation. Perform insertion-loss, return-loss, jitter, eye-diagram, and receiver-margin checks on every production board configuration rather than relying only on simulation.
Estimate total switch dissipation from the operating lane count, width, traffic activity, voltage, and enabled SerDes links, then compare the resulting junction-temperature margin with the package and board construction. The available materials do not state the complete electrical and thermal limits, so obtain the detailed specifications before defining copper area, airflow, or adjacent-component placement requirements.
Do not substitute a PCIe switch based only on lane count or advertised aggregate bandwidth. Confirm the package land pattern, every power and ground ball, lane polarity, reference-clock requirements, configuration interface, register behavior, and reset or startup sequence. The PEX8718, for example, is not pin-for-pin or firmware compatible because its architecture, register map, and configuration interfaces differ.
合規資訊
No explicit compliance declarations were found for this ordering code. Confirm material and environmental status with Broadcom before release.