Broadcom

PEX8608-BA50BC - 8-Lane Gen 2 PCIe Switch | Broadcom

MPN: PEX8608-BA50BC ✓ Nakahanda
196-PBGA, 15 x 15 mm Package
MOQ: 1 |

PEX8608-BA50BC Ulas

Broadcom PEX8608-BA50BC is a PCI Express switch IC with eight Gen 2 lanes at 5.0 GT/s, configurable into up to eight flexible ports, and a 196-PBGA package measuring 15 x 15 mm. It conforms to PCI Express Base Specification revision 2.0 and uses packet cut-through to minimize transfer delay.

A PCI Express switch is a semiconductor that routes high-speed serial transactions between a host or upstream endpoint and multiple downstream devices. Within the PCI Express hierarchy, this device is a PCIe switch, a fabric-based interface IC, and a system-level connectivity component. Eight SerDes lanes can be partitioned among several ports, allowing one compact system to aggregate endpoints for communications, control-plane, embedded, storage, and peer-to-peer equipment.

The PEX 8608 provides non-blocking internal switching, two virtual channels for traffic prioritization, and full line-rate operation on configured ports. Broadcom describes packet cut-through latency as 140 ns for an x4-to-x1 configuration in its product-page summary and as up to 130 ns in the linked feature documentation. SerDes outputs can be software-controlled for power reduction and signal-strength optimization.

Power management follows the PCI Express power-management specification. Unused SerDes physical links can be switched off to reduce power consumption, while controllable SerDes outputs allow system software to tune operating conditions. The switch architecture supports flexible port configurations, virtual-channel traffic separation, and scalable aggregation without relying on an external switch fabric for each endpoint connection.

Typical deployments include communications platforms, embedded systems, backplane aggregation, industrial controllers, test equipment, and servers that need additional PCIe endpoints. The eight-port capability makes it useful where several endpoint types, link widths, or downstream devices must share a compact host interface while retaining deterministic low-latency routing.

Design the PCB with the manufacturer’s 196-PBGA land pattern, high-speed differential routing rules, reference-plane continuity, and decoupling recommendations. Validate lane configuration, firmware or register programming, auxiliary power sequencing, and thermal performance across the intended traffic profile before production release. The exact pin assignments and electrical limits must be taken from the pin-description table in the manufacturer datasheet.

This page consolidates the official product architecture, package information, Gen 2 link capability, application fit, and practical implementation considerations. It also distinguishes confirmed drop-in coverage from broad functional equivalents, helping engineers determine whether a candidate can be soldered onto the same PCB land pattern rather than merely serving a similar PCIe-switch function.

Mga alternatibo na pwedeng ilagay na PEX8608-BA50BC — parehas na package, pin-to-pin na katugmang. Hindi kasama ang mga bahagi ng iba't-ibang package na nangangailangan ng pagpapaayos ng PCB.

PEX8608-BA50BC-G

✅ Drop-In
📦 196-PBGA (15 x 15 mm)
Identical PEX 8608 architecture, lane count, port count, and 196-PBGA package; ordering suffix differs, with exact ball-map equivalence requiring package-drawing confirmation.

📋 Alternatibo na Reference (hindi sa katalogo)

PEX8608-BA50BC Mga Pinakamataas na Rating at Electrical Characteristics

Product Type PCI Express switch IC
PCI Express Generation Gen 2
Maximum Data Rate 5.0 GT/s
PCIe Lane Count 8 lanes
Maximum Configurable Port Count 8 ports
PCI Express Base Specification Revision 2.0
Packet Cut-Through Latency 140 ns for x4-to-x1 configuration
Documented Maximum Cut-Through Latency 130 ns for x4-to-x1 configuration
Virtual Channels 2
Internal Switching Non-blocking
Power Management PCI Express power-management specification compliant
SerDes Link Control Software-controlled outputs and unused-link shutdown
Packhaging 196-PBGA, 15 x 15 mm
Uri ng Pagpapasok Surface mount

Gabay sa Pin Configuration ng PEX8608-BA50BC 196-pbga, 15 x 15 mm

Pin configuration para sa PEX8608-BA50BC (196-pbga, 15 x 15 mm package). Ang analog component na ito ay may input, output, at power supply pins. Sumangguni sa datasheet ng manufacturer para sa offset null, compensation, at enable pin configurations. Perpekto para sa signal conditioning at amplifier circuits.

Pinout diagram ng 196-pbga, 15 x 15 mm package para sa PEX8608-BA50BC

Wala ng detalyadong pinout data na magagamit para sa PEX8608-BA50BC.

Sumangguni sa datasheet para sa buong pin configuration.

Tipikal na mga Gamit

PEX8608-BA50BC ay nararapat para sa 3 aplikasyons: Pagkondisyon ng Signal, Pagkuha ng Data, Pagproseso ng Audio.

📊

Pagkondisyon ng Signal

Pagpapalakas at pag-filter ng mga signal ng sensor gamit ang PEX8608-BA50BC.

📈

Pagkuha ng Data

Pag-convert ng mga analog signal para sa digital processing gamit ang PEX8608-BA50BC.

🎧

Pagproseso ng Audio

Pagpapalakas at pagproseso ng audio signal gamit ang PEX8608-BA50BC.

What is the Broadcom PEX8608-BA50BC?
The Broadcom PEX8608-BA50BC is an eight-lane, eight-port PCI Express Gen 2 switch operating at up to 5.0 GT/s. According to the Broadcom PEX 8608 product page, it conforms to PCI Express Base Specification revision 2.0, supports packet cut-through, and provides two virtual channels. The device is packaged in a 196-PBGA measuring 15 x 15 mm for surface-mounted system integration.
How many PCIe lanes and ports does the PEX8608-BA50BC support?
The PEX8608-BA50BC provides eight PCI Express Gen 2 lanes and can be configured for up to eight flexible ports. According to Broadcom’s PEX 8608 product page, lane resources can be divided among downstream ports to support different endpoint arrangements. This makes the switch suitable for aggregation, fan-out, peer-to-peer, communications, control-plane, and embedded systems.
What is the data rate of the PEX8608-BA50BC?
The PEX8608-BA50BC supports a maximum PCIe Gen 2 data rate of 5.0 GT/s per lane. Broadcom identifies the device as an eight-lane switch with a non-blocking internal architecture. Its packet cut-through design moves frames without requiring them to be buffered through a conventional store-and-forward path, supporting low-latency traffic handling.
Where can I download the PEX8608-BA50BC datasheet PDF?
The official Broadcom feature document for the PEX 8608 is available at https://docs.broadcom.com/doc/12351823, while the manufacturer product page is https://www.broadcom.com/products/pcie-switches-retimers/pcie-switches/pex8608. Use the manufacturer’s pin-description table for all 196 package assignments and the detailed technical specifications for electrical limits, programming, reference circuits, and layout guidance.
Where can I find the PEX8608-BA50BC pinout?
Use the 196-PBGA pin-description table in the Broadcom PEX 8608 manufacturer documentation to identify every ball location and signal name. The product package is a 15 x 15 mm PBGA, so its physical pinout is a 196-position ball map rather than a conventional leaded-device drawing. Do not infer ball assignments from another switch model because auxiliary signals, clocking, power, and lane assignments can differ.
Is the PEX8608-BA50BC suitable for low-latency embedded systems?
The PEX8608-BA50BC is suitable for embedded and communications systems requiring a compact multiport PCIe fabric. Broadcom states that packet cut-through latency is 140 ns for an x4-to-x1 configuration, while its feature document lists up to 130 ns for that configuration. The eight-lane resource can be partitioned across several endpoints, but final latency depends on port width, traffic, and system configuration.
What is the difference between PCIe switching and a PCIe endpoint?
A PCIe switch routes transactions among multiple downstream devices, whereas a PCIe endpoint directly implements a function such as storage, networking, or acquisition. The PEX8608-BA50BC is a switch with eight Gen 2 lanes and up to eight configurable ports. It therefore belongs at a fan-out or aggregation point rather than serving as the endpoint controller for a single PCIe function.
Can the PEX8608-BA50BC reduce power in unused ports?
The PEX8608-BA50BC can reduce power by switching off unused SerDes physical links and by providing software control over SerDes outputs. Broadcom’s PEX 8608 documentation states that these controls support lower-power operation and optimization of signal strength. The achievable savings depend on the selected port widths, active lanes, operating mode, and system power-management policy.
When should I choose the PEX8608-BA50BC over another PCIe switch?
Choose the PEX8608-BA50BC when the design needs eight Gen 2 lanes, as many as eight flexible ports, two virtual channels, and a non-blocking cut-through fabric in a 196-PBGA package. It is particularly useful for embedded, communications, control-plane, and aggregation systems. Select another switch only if its lane count, port flexibility, data rate, package, firmware interface, or thermal rating better matches the target system.
Is the PEX8608-BA50BC suitable for backplane aggregation?
The PEX8608-BA50BC is suitable for backplane aggregation because it combines eight Gen 2 lanes with flexible mult port configuration and non-blocking internal routing. Broadcom identifies communications platforms, control-plane applications, embedded systems, fan-out, aggregation, and peer-to-peer interconnection as use cases for the PEX 8608. Board-level signal integrity and power sequencing still require validation against the manufacturer layout guidance.
What is the best drop-in replacement for the PEX8608-BA50BC?
No independently verified drop-in replacement was identified for the PEX8608-BA50BC. A valid drop-in candidate must use the same 196-PBGA land pattern, preserve pin-to-pin signal assignments, and remain within the required PCIe Gen 2 electrical and port-management limits. Use the Request a Quote form on this page to discuss sourcing or replacement support, and do not treat a functionally similar PCIe switch as automatically interchangeable.
Can another PCIe switch replace the PEX8608-BA50BC?
Another PCIe switch can replace the PEX8608-BA50BC only after confirming the same 196-PBGA footprint, identical pin functions, compatible power rails, equivalent register or firmware behavior, and acceptable lane and port performance. The available cross-reference information specifically identifies the PEX8608-BA50BC-G as non-pin-for-pin compatible with the PEX8718 because architecture, register map, and configuration interfaces differ.
What is the Broadcom equivalent of the PEX8608-BA50BC?
The Broadcom ordering code PEX8608-BA50BC-G refers to the PEX 8608 family and is associated with the same eight-lane, eight-port Gen 2 switch architecture and 196-PBGA package. However, an ordering-code or packing-code match must be checked against the manufacturer’s package drawing and pin table before treating it as an unqualified drop-in replacement. Request the current configuration through the quote form on this page.
Where to buy the PEX8608-BA50BC online?
Use the Request a Quote form on this page to request the Broadcom PEX8608-BA50BC, current availability, and a production quotation. The form connects the request directly with XAIPART without embedding a changing price in the technical description. Include your required quantity, target date, and packaging preference when requesting the quote.
What is the lead time for the Broadcom PEX8608-BA50BC?
Current lead time and minimum order quantity for the PEX8608-BA50BC should be confirmed through the Request a Quote form on this page. Lead time can vary with order quantity, supply status, package configuration, and production schedule. Provide your forecast quantities and required delivery date so the sourcing response can reflect the actual manufacturing plan.
What are the key specifications engineers should know about the PEX8608-BA50BC?
The PEX8608-BA50BC combines eight PCIe Gen 2 lanes, up to eight configurable ports, 5.0 GT/s operation, two virtual channels, and packet cut-through in a 196-PBGA package. Broadcom describes the internal switch as non-blocking and reports 140 ns latency for x4-to-x1 configuration, with another feature document stating up to 130 ns. The switch also supports SerDes output control and unused-link shutdown.

Impormasyon ng Talumpati sa Engineering for PEX8608-BA50BC — ikabit, gabay sa disenyo, at impormasyon ng pagsunod sa kautusan.

Paunawang Hanapin

Choose the PEX8608-BA50BC when a system needs an eight-lane PCIe Gen 2 fabric with up to eight flexible ports, two virtual channels, and low-latency packet cut-through in a 196-PBGA package. It is a strong fit for communications platforms, embedded equipment, backplane aggregation, and control-plane systems with several downstream endpoints. The Broadcom PEX8608-BA50BC-G ordering variant preserves the same architecture and package, but confirm the exact ball map and ordering code before treating it as a drop-in choice. Do not select a functionally similar switch merely because it also has eight lanes: PCIe generation, port flexibility, reference clock, initialization method, register map, auxiliary-power sequencing, and PCB footprint must all align. For designs requiring newer PCIe generations, lower latency, different port counts, or a different package, evaluate the newer switch family against system-level throughput, firmware effort, signal-integrity margins, and thermal constraints rather than forcing a board redesign around the PEX 8608.

Ikabit sa Mga Alternatibo

Parametro Ito ang Producto PEX8608-BA50BC-G
Package 196-PBGA (15 x 15 mm) 196-PBGA (15 x 15 mm)
Brand Broadcom Broadcom
PCIe Generation Gen 2 Gen 2
Maximum Data Rate 5.0 GT/s 5.0 GT/s
Lane Count 8 lanes 8 lanes
Maximum Port Count 8 flexible ports 8 flexible ports
Packet Cut-Through Latency 140 ns for x4-to-x1 configuration 140 ns for x4-to-x1 configuration
Virtual Channels 2 2
Internal Switching Non-blocking Non-blocking
SerDes Control Software-controlled outputs with unused-link shutdown Software-controlled outputs with unused-link shutdown

Pangunahing mga Pagkakaiba

  • Eight flexible PCIe lanes in one switch (kumpara saPEX8718)
  • Packet cut-through for low-latency routing (kumpara saPEX8608-BA50BC-G)
  • Software-controlled SerDes power optimization (kumpara saPEX8718)

Talaan ng Disenyo

Route all PCIe differential pairs as impedance-controlled, length-matched transmission lines with continuous reference planes. Place the transceiver and bypass components according to the manufacturer’s reference circuit and layout guidance, minimize stub branches, and avoid routing high-speed links across plane splits. Validate the final 196-BGA escape fanout with the PCB manufacturer’s fine-pitch assembly capability.

Separate each supply domain and follow the manufacturer’s recommended startup, decoupling, and auxiliary-power sequencing. Place the required high-frequency capacitors close to their associated power and ground balls, and maintain low-impedance planes from the package to the supply network. Power-domain sequencing must also satisfy every downstream endpoint because an incorrectly ordered auxiliary rail can prevent the switch from enumerating reliably.

Configure lane widths only after confirming the complete point-to-point link budget from the upstream host through the PEX 8608 to each downstream endpoint. Use the manufacturer’s SerDes configuration procedure, test masks, and compliance constraints during validation. Perform insertion-loss, return-loss, jitter, eye-diagram, and receiver-margin checks on every production board configuration rather than relying only on simulation.

Estimate total switch dissipation from the operating lane count, width, traffic activity, voltage, and enabled SerDes links, then compare the resulting junction-temperature margin with the package and board construction. The available materials do not state the complete electrical and thermal limits, so obtain the detailed specifications before defining copper area, airflow, or adjacent-component placement requirements.

Do not substitute a PCIe switch based only on lane count or advertised aggregate bandwidth. Confirm the package land pattern, every power and ground ball, lane polarity, reference-clock requirements, configuration interface, register behavior, and reset or startup sequence. The PEX8718, for example, is not pin-for-pin or firmware compatible because its architecture, register map, and configuration interfaces differ.

Impormasyon ng Pagsunod sa Kautusan

RoHS
Unknown
REACH
Unknown
AEC-Q100
Unknown
Walang Lead
Unknown
Walang Halogen
Unknown
Mga Conflict Mineral
Unknown

No explicit compliance declarations were found for this ordering code. Confirm material and environmental status with Broadcom before release.

Data napatotohanan sa: 2026-11-11 — impormasyon na pinatunayan at pinapatakbo ng pangkat ng engineering ng XAIPART's component engineering team

Kaugnay na Hanapin

PEX8608-BA50BC datasheet PEX8608-BA50BC datasheet pdf PEX8608-BA50BC pinout PEX8608-BA50BC 196 PBGA Broadcom PEX8608-BA50BC PEX8608-BA50BC 8 lane 8 port PEX8608-BA50BC PCIe Gen 2 switch PEX8608-BA50BC equivalent PEX8608-BA50BC replacement PEX8608-BA50BC cross reference PEX8608-BA50BC backplane aggregation PEX8608-BA50BC embedded system PEX8608-BA50BC price PEX8608-BA50BC stock PEX8608-BA50BC footprint

Mga kaugnay na Mga Komponente at mga Tuntunin

Broadcom PEX8608-BA50BC PEX8608-BA50BC-G PEX8718 PCI Express switch PCIe switch IC PCI Express Base Specification revision 2.0 PCI Express Gen 2 5.0 GT/s non-blocking switch architecture packet cut-through virtual channel SerDes PCI Express power management 196-PBGA PBGA package family surface-mount semiconductor embedded systems communications platforms control-plane applications backplane aggregation peer-to-peer networking ExpressLane signal integrity auxiliary power sequencing
Mabilis na Tanggap na RFQ
Ihanda ang buong detalye — ang aming pangkalakal na koponan ay tutugon sa loob ng 24 oras
Numero ng Parte Mga Tagagawa Pakete QTY Target na Halaga Pinalawak
✓
Quote na inilabas!

Ating tumugon sa iyong email sa loob ng 24 oras

1
RFQ Naisumite
2
Received na ang Kwaliksik
3
Nai-order
4
Pagbabayad
5
Inihanda
6
Naihanda
Tingnan ang Detalye ng RFQ