SI1553DL-T1-GE3 - Complementary 20V MOSFET Array | Vishay
部品番号: SI1553DL-T1-GE3 ✓ 生産中| 数量 | 単価 | 小計 |
|---|---|---|
| 1 | $0.42 | $0.42 |
| 10 | $0.37 | $3.70 |
| 100 | $0.28 | $28.00 |
| 500 | $0.22 | $110.00 |
| 1,000 | $0.18 | $180.00 |
| 3,000 | $0.14 | $420.00 |
SI1553DL-T1-GE3 概要
A complementary MOSFET pair (N-channel + P-channel on one substrate) is a building block for low-power switching applications where symmetrical high-side / low-side or push-pull drive is needed without using two discrete transistors. The two MOSFETs share the same 20 V VDS rating and 2.5 V gate-source threshold range, allowing them to be driven from the same logic-level control signal without level translation. By integrating both polarities in one SC-70 package, designers can halve the board footprint of equivalent discrete solutions and improve channel-to-channel thermal and parametric matching.
Key features include a low on-resistance of approximately 0.32 ohm at VGS = 4.5 V (N-channel) and 0.5 ohm (P-channel), making the part efficient for portable and battery-powered designs. The TrenchFET process technology minimizes RDS(on) per unit area, while 2.5 V gate threshold supports direct drive from 1.8 V and 3.3 V microcontroller GPIO outputs with logic-level enhancement. The SC-70-6 package provides a compact 2.0 x 1.25 mm footprint suited for handheld and wearable products, and the device is qualified over the -55C to +150C junction temperature range.
Typical applications include load switching in portable electronics, signal-level shifting between domains of different voltage rails, analog multiplexer / demultiplexer building blocks, and complementary push-pull drivers for small DC fans, relays, or LED strings. The small footprint also suits wearable health monitors and IoT sensor nodes where PCB area is at a premium.
When designing with this device, note that the N-channel and P-channel devices share the same SC-70 pinout but are not interchangeable with single-channel equivalents. Plan gate-drive RC snubbers and ensure VGS never exceeds the absolute maximum of +/- 8 V. For high-frequency circuits, keep the gate-loop PCB inductance low to prevent unintended ringing during switching transitions.
This page synthesizes distributor pricing, drop-in alternatives, and practical design notes not found in the manufacturer datasheet.
ドロップイン代替品: SI1553DL-T1-GE3 — 同一パッケージでピン互換。PCBの作り直しが必要な異なるパッケージの部品は除外されています。
このシリーズのバリエーション
同一シリーズでドロップイン互換のモデル: SI1553DL-T1-GE3 （同一形状・フットプリント） — 相違点: Operating Temperature Range, Manufacturer, Configuration, Package, RoHS Status.
クイック比較ツール — 並列比較する代替部品を選択:
SI1553CDL-T1-GE3
✅ ドロップイン📋 参考代替品（カタログ未掲載）
SI1553DL-T1-E3
✅ ドロップイン✓ 在庫あり
$0.22 / 個
データシートを見る →SI1553DL-T1
✅ ドロップイン📋 参考代替品（カタログ未掲載）
SI1553DL-T1-GE3 最大定格＆電気的特性
| Manufacturer | Vishay Siliconix |
| Part Number | SI1553DL-T1-GE3 |
| Transistor Polarity | Complementary N and P Channel |
| Number of Channels | 2 (1 N-channel + 1 P-channel) |
| Drain-Source Voltage VDS (max) | 20 V |
| Continuous Drain Current ID - N-Channel | 700 mA |
| Continuous Drain Current ID - P-Channel | 500 mA |
| On-Resistance RDS(on) - N-Channel | 0.32 ohm (typ at VGS = 4.5 V) |
| Gate-Source Threshold VGS(th) | 2.5 V (max) |
| Power Dissipation PD | 340 mW |
| 動作温度範囲 | -55C to +150C (TJ) |
| パッケージ | SC-70-6 / SOT-363-6 |
| 実装タイプ | Surface Mount |
| Process Technology | TrenchFET |
| Termination Finish | Lead-free (Pb-free), Halogen-free |
| RoHS Compliance | Compliant per Directive 2002/95/EC |
| ハロゲンフリー | Yes (per IEC 61249-2-21) |
SI1553DL-T1-GE3 ピン構成
| ピン 1 | S1 — Source 1 (N-channel) |
| ピン 2 | G1 — Gate 1 (N-channel) |
| ピン 3 | D2 — Drain 2 (P-channel) |
| ピン 4 | S2 — Source 2 (P-channel) |
| ピン 5 | D1 — Drain 1 (N-channel) |
| ピン 6 | G2 — Gate 2 (P-channel) |
主な用途
SI1553DL-T1-GE3 の用途: 6 件s: Portable Load Switching, Signal-Level Shifting, Complementary Push-Pull Driver, Analog Multiplexer Building Block, Wearable Health Monitor Sensor Switches, IoT Sensor Node Power Gating.
Portable Load Switching
The SI1553DL-T1-GE3's complementary N+P-channel integration in a 2.0 x 1.25 mm SC-70-6 package makes it ideal for portable load-switch circuits in smartphones, wearables, and handheld instruments. Its N-channel 700 mA rating handles high-side switching of downstream regulators, while the P-channel 500 mA provides low-side return-path control. With 0.32 ohm RDS(on) (N-ch) at VGS = 4.5 V, conduction loss stays under 50 mW at 200 mA load, preserving battery runtime. The 2.5 V VGS(th) enables direct GPIO drive from 1.8 V / 3.3 V MCUs without level translation. Place the part near the load with input/output capacitors to minimize parasitic inductance.
おすすめ
Signal-Level Shifting
The SI1553DL-T1-GE3 simplifies bidirectional level shifting between mismatched logic domains, e.g. 1.8 V to 3.3 V or 3.3 V to 5 V. The N-channel acts as the high-side pass device and the P-channel as the low-side return, forming a transmission gate that passes analog or digital signals in either direction. Its 20 V VDS provides ample headroom even for 5 V domains, and the 2.5 V VGS(th) ensures clean turn-off when gate is grounded. Designers should add series resistors on each side of the gate-source path to limit inrush current during domain transitions and to prevent shoot-through in the complementary pair.
おすすめ
Complementary Push-Pull Driver
In small DC fan, relay, or audio output stages, the SI1553DL-T1-GE3 provides matched complementary drive with N-channel pull-down and P-channel pull-up in a single 6-pin package. The matched VGS(th) of both devices minimizes shoot-through current and crossover distortion, critical for audio or motor applications. With 700 mA peak N-channel drive, the part handles small brushless fans up to 200 mA continuous without thermal issues when mounted on 1 square inch of copper. Decoupling the gate drive with 100 ohm series resistors slows edges to about 50 ns, reducing EMI while keeping switching loss minimal.
おすすめ
Analog Multiplexer Building Block
Two SI1553DL-T1-GE3 parts can form a 4-channel single-pole double-throw (SPDT) analog switch for low-frequency signal routing in test equipment, data acquisition front-ends, or audio mixers. The complementary pair provides bidirectional conduction paths, and the 20 V signal range covers most analog signal swings. The 0.32 ohm RDS(on) of the N-channel keeps on-state signal attenuation minimal, while the P-channel provides the symmetric return path. Designers should account for charge injection at the gate and add a small hold capacitor at the output for sample-and-hold applications.
おすすめ
Wearable Health Monitor Sensor Switches
The SI1553DL-T1-GE3's 2.0 x 1.25 mm SC-70-6 footprint and 0.32 ohm RDS(on) suit wearable health monitors where board area is at a premium. The N-channel can power-gate a heart-rate sensor or temperature sensor between measurements, while the P-channel provides the complementary return. The 20 V VDS rating is far above the typical 3.7 V Li-ion cell voltage, providing robust transient margin. Halogen-free / lead-free finish (per IEC 61249-2-21) is required for medical and consumer-wearable compliance with RoHS and REACH regulations.
おすすめ
IoT Sensor Node Power Gating
For battery-powered IoT sensor nodes (Zigbee, BLE, LoRa), the SI1553DL-T1-GE3 provides ultra-low quiescent current power gating of sub-systems like sensors, RF transceivers, or auxiliary MCUs. The 2.5 V VGS(th) ensures the MOSFETs are fully off when the gate is grounded, with sub-microamp leakage. The complementary pair can power-gate a sensor on the high side while providing a return-path disconnect on the low side, achieving true shutdown isolation. Pairing it with an MCU GPIO enables duty-cycled sensor activation, extending coin-cell battery life by an order of magnitude.
おすすめ
おすすめ製品の概要
エンジニアリング参考データ: SI1553DL-T1-GE3 — 比較、設計ガイダンス、コンプライアンス情報。
選定ガイド
代替品との比較
| パラメータ | この製品 | SI1553CDL-T1-GE3 | SI1553DL-T1-E3 | SI1553DL-T1 |
|---|---|---|---|---|
| Package | SC-70-6 (SOT-363) | SC-70-6 (SOT-363) - same | SC-70-6 (SOT-363) - same | SC-70-6 (SOT-363) - same |
| Brand | Vishay Siliconix | Vishay Siliconix - same | Vishay Siliconix - same | Vishay Siliconix - same |
| VDS (max) | 20 V | 20 V | 20 V | 20 V |
| N-Channel ID (continuous) | 700 mA | 700 mA | 700 mA | 700 mA |
| P-Channel ID (continuous) | 500 mA | 500 mA | 500 mA | 500 mA |
| N-Channel RDS(on) | 0.32 ohm (typ at VGS = 4.5 V) | 0.32 ohm (improved in C-revision) | 0.32 ohm | 0.32 ohm |
| VGS(th) (max) | 2.5 V | 2.5 V | 2.5 V | 2.5 V |
| Power Dissipation | 340 mW | 340 mW | 340 mW | 340 mW |
| Termination Finish | Pb-free + Halogen-free (GE3) | Pb-free + Halogen-free (GE3) | Pb-free only, NOT halogen-free | SnPb (tin-lead), NOT RoHS |
| RoHS Compliance | Compliant | Compliant | Compliant | Non-compliant |
主な差別化要因
- Single-package complementary pair （vs Two discrete MOSFETs (e.g., 2N7002 + BSS84))
- Lead-free and halogen-free termination （vs SI1553DL-T1-E3 (Pb-free only))
- Higher N-channel current than typical SOT-363 parts （vs SI1555DL-T1-E3 (8V/lower-current family))
設計ノート
Estimated: at 700 mA continuous drain current with RDS(on) of 0.32 ohm (N-channel), conduction loss is approximately 0.16 W. With a SC-70 theta_JA of approximately 500 C/W on a 1 square inch copper pour, junction temperature rise is about 80 C above ambient. For sustained high-current switching (e.g., PWM-driven at >50% duty), increase copper area or use thermal vias to maintain TJ below 150 C. Source: Vishay datasheet 71078 and general SC-70 thermal guidelines.
Route the gate traces with 50 ohm controlled impedance if switching edges below 20 ns are required. Place a 100 ohm series gate resistor close to each gate pin to dampen parasitic ringing. Keep the source-return path of each MOSFET short - source inductance creates a feedback loop that can cause spurious oscillation during fast switching. The SC-70-6 footprint requires a small land pattern (see IPC-7351 SC-70 standard).
Do not exceed VGS absolute maximum of 8 V (verify against latest datasheet revision) - over-voltage on the gate oxide permanently damages the MOSFET. The 2.5 V VGS(th) means the MOSFET is not fully enhanced at 1.8 V GPIO drive; ensure VGS >= 4.5 V for lowest RDS(on). Avoid using both channels simultaneously in a non-complementary configuration without checking SOA - the shared substrate can cause thermal cross-coupling between channels.
コンプライアンス情報
Lead-free and halogen-free per Vishay datasheet 71078 (IEC 61249-2-21). RoHS compliant per 2002/95/EC. AEC-Q100 automotive qualification status not stated in available data - assume not qualified unless verified against latest Vishay reliability report.
