TPS61240DRVT - 5V 450mA Boost Converter | Texas Instruments
部品番号: TPS61240DRVT ✓ 生産中| 数量 | 単価 | 小計 |
|---|---|---|
| 1 | $1.55 | $1.55 |
| 10 | $1.4 | $14.00 |
| 100 | $1.2 | $120.00 |
| 500 | $1.05 | $525.00 |
| 1,000 | $0.92 | $920.00 |
TPS61240DRVT 概要
A boost converter (step-up converter) is a switching power supply topology that produces an output voltage higher than its input. It is part of the DC-DC converter family under switched-mode power supplies (SMPS) within power management ICs. Boost converters use an inductor, switch, diode (or synchronous rectifier), and output capacitor to store and release energy, achieving efficiencies far above what linear regulators can deliver when VIN is well below VOUT.
Key features of the TPS61240DRVT include 90% typical efficiency at nominal operating conditions, 5.0V ±2% total DC output voltage accuracy, 30 µA quiescent current, and best-in-class line and load transient response. The wide input range of 2.3V to 5.5V is ideal for batteries with extended voltage ranges, and the high 3.5 MHz switching frequency enables the use of small inductors and ceramic capacitors in space-constrained portable designs.
The TPS61240DRVT uses a synchronous rectification topology with an internal input valley current limit of 500 mA. Its control architecture minimizes quiescent current while delivering strong transient response, allowing the device to extend battery life across light-load and full-load operating conditions. The exposed thermal pad on the WSON-6 package provides a low thermal resistance path.
Typical applications include USB OTG/peripheral power supplies, single-cell Li-Ion to 5V boost converters, three-cell alkaline-powered portable electronics, MCU/digital logic supply rails, and handheld consumer devices. Its fixed 5V output simplifies USB-powered designs by eliminating the need for external feedback resistors.
When designing with this device, ensure the input valley current limit is not exceeded under maximum load conditions and follow TI's recommended inductor and capacitor values for stable operation. A bypass capacitor close to the IC input is required for noise-sensitive analog rails sharing the boost converter.
This page synthesizes distributor pricing, drop-in alternatives, and practical design notes not found in the manufacturer datasheet.
ドロップイン代替品: TPS61240DRVT — 同一パッケージでピン互換。PCBの作り直しが必要な異なるパッケージの部品は除外されています。
このシリーズのバリエーション
同一シリーズでドロップイン互換のモデル: TPS61240DRVT （同一形状・フットプリント） — 相違点: Output Voltage, Package, Input Voltage Range, Topology, Switching Frequency.
クイック比較ツール — 並列比較する代替部品を選択:
TPS61240DRVR
✅ ドロップイン✓ 在庫あり
$0.86 / 個
データシートを見る →TPS61241DRVT
✅ ドロップイン📋 参考代替品（カタログ未掲載）
TPS61240DRVRG4
✅ ドロップイン ⚠️ 仕様未検証📋 参考代替品（カタログ未掲載）
TPS61240YFFT
✅ ドロップイン ⚠️ 仕様未検証📋 参考代替品（カタログ未掲載）
TPS61241DRVR
✅ ドロップイン ⚠️ 仕様未検証📋 参考代替品（カタログ未掲載）
TPS61240DRVT 最大定格＆電気的特性
| トポロジー | Boost (Step-Up) |
| 入力電圧範囲 | 2.3 V to 5.5 V |
| 出力電圧 | 5.0 V (Fixed) |
| 最大出力電流 | 450 mA |
| Input Valley Current Limit | 500 mA |
| スイッチング周波数 | 3.5 MHz (Typical) |
| 静止電流 | 30 µA (Typical) |
| 効率 | 90% (Nominal Operating Conditions) |
| Output Voltage Accuracy | ±2% |
| 同期整流器 | Yes (Integrated) |
| 動作温度 | -40 °C to +85 °C |
| パッケージ | WSON-6 (DRV) 2 mm × 2 mm with Exposed Pad |
| 実装タイプ | Surface Mount |
| MSLレベル | 2 |
| RoHS ステータス | Compliant |
TPS61240DRVT ピン構成
| ピン 1 | VIN — Input voltage supply (2.3 V to 5.5 V) |
| ピン 2 | GND — Analog ground |
| ピン 3 | EN — Enable input (active high, internal pull-down) |
| ピン 4 | NC — Not connected (per datasheet) |
| ピン 5 | VOUT — Boost converter output (5.0 V fixed) |
| ピン 6 | SW — Switch node to external inductor |
| ピン EP | PGND — Power ground and thermal pad (must be soldered to PCB ground) |
主な用途
TPS61240DRVT の用途: 6 件s: USB OTG / Peripheral Power Supply, Single-Cell Li-Ion to 5V Boost Converter, Three-Cell Alkaline / NiMH Powered Devices, MCU and Digital Logic 5V Supply Rail, Handheld Consumer / Wearable Devices, Industrial Sensor / IoT Node Power.
USB OTG / Peripheral Power Supply
The TPS61240DRVT's fixed 5.0 V output eliminates external feedback resistors, making it an ideal single-cell Li-Ion to 5 V boost converter for USB OTG and peripheral power rails. The 450 mA output capability covers USB 2.0 downstream port power requirements (500 mA) with margin, while the 90% typical efficiency minimizes battery drain. The 3.5 MHz switching frequency enables use of a 1 µH chip inductor, fitting USB dongle and hub designs within tight footprint constraints. According to TI reference designs, the TPS61240 typically pairs with a TPS2051B power switch for current-limited USB output protection.
おすすめ
Single-Cell Li-Ion to 5V Boost Converter
The TPS61240DRVT is purpose-built for boosting a single-cell Li-Ion/Li-Polymer battery (2.7 V to 4.2 V nominal) to a stable 5 V rail. The 2.3 V to 5.5 V input range covers the full Li-Ion discharge curve including under-voltage cutoff, while the synchronous topology delivers 90% efficiency at nominal conditions. The 30 µA quiescent current extends standby time in intermittently loaded products like wireless sensors and BLE beacons. TI's TPS61240 datasheet typical application circuit uses a single 1.0 µH inductor and 4.7 µF ceramic input/output capacitors for a complete < 25 mm² solution footprint.
おすすめ
Three-Cell Alkaline / NiMH Powered Devices
The TPS61240DRVT supports three-cell alkaline, NiCd, or NiMH battery packs (3.0 V nominal, 4.5 V end-of-charge) with its 2.3 V to 5.5 V input range. This is critical for toys, portable instruments, and consumer electronics that need a regulated 5 V rail for digital logic or USB charging from a battery source that swings widely. The 90% efficiency and 30 µA quiescent current maximize battery life, while the WSON-6 (DRV) package with exposed thermal pad handles the boost inductor heat dissipation in continuous-conduction operation.
おすすめ
MCU and Digital Logic 5V Supply Rail
The TPS61240DRVT generates a clean 5 V rail for 5 V-tolerant MCUs, logic ICs, and display drivers from a 3.3 V system battery. The fixed 5 V output eliminates feedback design complexity, while the ±2% accuracy over line and load ensures tight supply tolerance for digital logic thresholds. Best-in-class line and load transient response per TI's TPS61240 datasheet protects downstream logic during dynamic load steps. The exposed thermal pad of the WSON-6 (DRV) package maintains cool operation under sustained boost duty.
おすすめ
Handheld Consumer / Wearable Devices
The TPS61240DRVT's tiny 2 mm × 2 mm WSON-6 package, 1.0 µH inductor compatibility, and 30 µA quiescent current make it ideal for space-constrained wearables like fitness bands, smart watches, and wireless earbuds charging cases. Boost efficiency of 90% extends runtime on small Li-Polymer cells, while the synchronous rectification eliminates the external Schottky diode for further board-area savings. TI's TPS61240 datasheet typical application fits in under 25 mm² total, including inductor and ceramic capacitors, suiting sub-100 mA wearable rail designs.
おすすめ
Industrial Sensor / IoT Node Power
The TPS61240DRVT's wide 2.3 V to 5.5 V input range, 5 V fixed output, and industrial -40 °C to +85 °C operating range make it suitable for industrial IoT sensors powered by 3.6 V lithium-thionyl-chloride primary cells or 3.7 V Li-Ion rechargeable packs. The 450 mA output handles short RF transmit bursts from sub-GHz or BLE radios that share a boost supply. The 90% efficiency and 30 µA quiescent current support multi-year battery life in low-duty-cycle wireless sensor nodes per TI's TPS61240 datasheet application information.
おすすめ
おすすめ製品の概要
エンジニアリング参考データ: TPS61240DRVT — 比較、設計ガイダンス、コンプライアンス情報。
選定ガイド
代替品との比較
| パラメータ | この製品 | TPS61240DRVR | TPS61241DRVT | TPS61240DRVRG4 | TPS61241DRVR |
|---|---|---|---|---|---|
| Brand | Texas Instruments | Texas Instruments | Texas Instruments | Texas Instruments | Texas Instruments |
| Package | WSON-6 (DRV) 2x2 mm | WSON-6 (DRV) - same | WSON-6 (DRV) - same | WSON-6 (DRV) - same | WSON-6 (DRV) - same |
| Topology | Synchronous Boost (Step-Up) | Synchronous Boost | Synchronous Boost | Synchronous Boost | Synchronous Boost |
| Input Voltage Range | 2.3 V to 5.5 V | 2.3 V to 5.5 V | 2.3 V to 5.5 V | 2.3 V to 5.5 V | 2.3 V to 5.5 V |
| Output Voltage | 5.0 V (Fixed) | 5.0 V (Fixed) | 5.0 V (Fixed) | 5.0 V (Fixed) | 5.0 V (Fixed) |
| Maximum Output Current | 450 mA | 450 mA | 450 mA (typ) | 450 mA | 450 mA (typ) |
| Input Valley Current Limit | 500 mA | 500 mA | 600 mA (+20%) | 500 mA | 600 mA (+20%) |
| Switching Frequency | 3.5 MHz | 3.5 MHz | 3.5 MHz | 3.5 MHz | 3.5 MHz |
| Quiescent Current | 30 µA | 30 µA | 30 µA | 30 µA | 30 µA |
| Operating Temperature | -40 °C to +85 °C | -40 °C to +85 °C | -40 °C to +85 °C | -40 °C to +85 °C | -40 °C to +85 °C |
主な差別化要因
- Fixed 5 V output eliminates feedback resistors （vs TPS61240DRVR)
- Higher valley current limit (+20%) for sustained heavy loads （vs TPS61241DRVT)
- Compact WSON-6 (DRV) 2x2 mm package enables < 25 mm² designs （vs TPS61240YFFT)
設計ノート
Per TI's TPS61240 datasheet layout guidelines, place the input capacitor, output capacitor, and inductor as close to the IC as possible to minimize switching node parasitic inductance. Use a wide ground plane under the exposed thermal pad (EP) of the WSON-6 package to reduce thermal resistance and provide a low-impedance return path for the high-frequency switching currents. Keep the SW trace short and away from sensitive analog traces to avoid noise coupling.
Do not exceed the 500 mA input valley current limit (use TPS61241 for higher loads). The EN pin has an internal pull-down - leave it floating to disable, or drive high to enable. Avoid using electrolytic output capacitors; the TPS61240 datasheet requires low-ESR ceramic capacitors (X5R/X7R) for stable loop compensation. Per TI's recommended component list, use a 1.0 µH inductor with saturation current above 1 A for full-load operation.
Estimated: At VIN=3.0 V, VOUT=5.0 V, IOUT=450 mA, the boost converter dissipates approximately P = (VOUT-VIN)/VOUT × POUT = 0.4 × 2.25 W = 0.9 W assuming 90% efficiency. With the WSON-6 (DRV) package exposed thermal pad soldered to adequate copper (recommended ≥ 50 mm²), theta_JA is approximately 60 °C/W, giving a junction temperature rise of ~54 °C above 25 °C ambient - well within the 125 °C maximum junction rating.
The TPS61240 supports a true load-disconnect behavior by disabling the synchronous rectifier when EN is low, eliminating DC leakage from input to output. This is critical for battery-powered designs where shutdown current must remain in the single-digit µA range. Per TI's TPS61240 datasheet, total shutdown current is typically < 5 µA. Place a 4.7 µF X5R ceramic capacitor at VOUT to minimize output ripple at heavy load steps.
コンプライアンス情報
RoHS and REACH compliant per TI product page. Not AEC-Q100 qualified - this is a commercial/industrial-grade part. Lead-free (Pb-free) and halogen-free per TI Material Composition Declaration.
