집적 회로

PIC32MX570F512LT-I/GJX

PIC32MX570F512LT-I/GJX - 50MHz 32-bit MCU 512KB Flash TFBGA-100

The Microchip Technology PIC32MX570F512LT-I/GJX is a 32-bit MIPS32 M4K microcontroller running at up to 50 MHz/83 DMIPS, integrating 512 KB of Flash program memory and 64 KB of SRAM in a compact 100-pin TFBGA (7x7 mm) package. Per the Microchip datasheet, this member of the PIC32MX1XX/2XX/5XX 64/100-pin family combines a high-performance core with USB 2.0 Full-Speed OTG, CAN 2.0B with DeviceNet addressing, two I2S and four SPI modules, a Parallel Master Port (PMP) with dual buffers, and Peripheral Pin Select (PPS) for flexible signal routing. The 'L' suffix indicates the industrial -40C to +85C temperature range and 100-pin package option, while 'T' denotes tape-and-reel packaging. A 32-bit microcontroller (MCU) is an integrated circuit that combines a processor core, program memory (Flash), data memory (SRAM), and a rich set of on-chip peripherals such as timers, communication controllers, and analog blocks. In the system hierarchy, an MCU sits above discrete logic and below a system-on-chip (SoC); the PIC32MX570F512L family targets cost-sensitive embedded applications where MIPS architecture, deterministic interrupt response, and Microchip's MPLAB Harmony toolchain deliver faster development cycles than ARM Cortex-M parts at similar Flash densities. Key differentiating features include the 50 MHz/83 DMIPS M4K core, integrated Full-Speed USB OTG and CAN 2.0B, an on-chip 16-channel 10-bit ADC with up to 1 Msps sampling, three analog comparators plus a CTMU (Charge Time Measurement Unit) for capacitive touch sensing, and a real-time clock/calendar (RTCC). The 100-pin TFBGA (7x7) footprint provides ample I/O for parallel graphics and PMP-driven LCD interfaces while keeping PCB area minimal. Architecturally, the part uses a 5-stage pipelined M4K core with hardware multiply/divide, dual I-cache/S-cache, a flexible DMA controller, and Microchip's PPS - allowing most digital peripherals to be remapped to a wide choice of physical pins, which simplifies PCB layout and BOM reuse across family members. Typical applications include industrial USB peripherals, CAN-based automotive body controllers, audio HMI with I2S codecs, capacitive-touch human-machine interfaces, low-cost graphics terminals, and embedded data-acquisition front-ends. The combination of USB device/host/OTG plus CAN in a single 100-pin BGA makes this MCU particularly attractive for industrial-control gateways. A key design trade-off is the TFBGA-7x7 package: it minimizes PCB area but requires careful via-in-pad design and X-ray inspection during assembly. Engineers should budget for an additional PCB layer and reflow profile tuning to obtain reliable BGA solder joints in production. This page synthesizes distributor pricing, drop-in alternatives, and design notes not found in the manufacturer datasheet, giving buyers and engineers a single authoritative source for procurement and design decisions.

USD $4.78 재고 있음

PIC32MX570F512LT-V/GJX

PIC32MX570F512LT-V/GJX - 50MHz 32-bit MCU, 512KB Flash, TFBGA-100 | Microchip

The Microchip PIC32MX570F512LT-V/GJX is a 32-bit MIPS32 M4K microcontroller running at up to 50 MHz (83 DMIPS), integrating 512 KB of Flash program memory and 64 KB of SRAM in a 100-pin TFBGA (7x7 mm) package. It is rated for the automotive V temperature grade (-40°C to +105°C) and supports 2.5 V / 3.3 V operation. The device is part of the PIC32MX5xx family and includes USB 2.0 Full-Speed, CAN 2.0B, four SPI modules, two I²S interfaces, four UART modules, five I²C modules, and a 16-channel 10-bit ADC at 1 Msps. A 32-bit microcontroller (MCU) is a single-chip processor that integrates a CPU core, program and data memory, and a rich set of peripherals on a single die, forming the compute backbone of embedded systems. The PIC32MX570 belongs to the broader taxonomy: 32-bit MCU -> embedded microcontroller -> microprocessor IC -> integrated circuit -> semiconductor. It uses a RISC load-store architecture and is typically paired with a real-time operating system (RTCC, FreeRTOS, Micrium) or runs bare-metal firmware in C. Key features of the PIC32MX570F512LT include Peripheral Pin Select (PPS), a Parallel Master Port (PMP) for graphics interfaces, a Charge Time Measurement Unit (CTMU) for capacitive touch and precise time measurement, three analog comparators, and a real-time clock/calendar (RTCC). The PIC32MX5xx family is optimized for cost-sensitive connectivity and HMI designs, combining a high-performance MIPS core with industrial-grade connectivity in a small BGA footprint that suits compact layouts. The MIPS32 M4K core implements a five-stage pipeline, hardware multiply/divide, and a single-cycle shadow register set for fast interrupt response, which together with the 83 DMIPS performance make it suitable for protocol stacks (USB, CAN, TCP/IP) running concurrently with application code. The 512 KB Flash supports self-programming via ICSP, and the 64 KB RAM accommodates large TCP/IP or USB buffers. Integrated DMA on the USB, CAN, and SPI/I²S peripherals offloads the CPU and enables deterministic throughput for streaming data such as audio or sensor telemetry. Typical applications for PIC32MX570F512LT-V/GJX include USB peripherals (HID, CDC, MSD, audio class), CAN-connected automotive body and gateway ECUs, industrial HMI with PMP-driven TFT displays, IoT edge nodes, and audio streaming devices using the I²S ports with an external CODEC. The combination of 50 MHz, USB, CAN, and 512 KB Flash targets cost-optimized designs that previously required a separate MCU plus external controller ICs. When designing with this part, ensure the BGA PCB land pattern follows IPC-7351 recommendations and that the exposed die-attach paddle (if applicable to the TFBGA substrate) is thermally connected for heat spreading. Firmware development is supported by MPLAB X IDE, MPLAB Harmony, and the XC32 compiler; programmers include PICkit 4, ICD 4, and MPLAB Snap. Engineers migrating from PIC32MX4 to PIC32MX5 benefit from binary-compatible peripherals while gaining USB and CAN.

USD $5.92 재고 있음

PIC32MX570F512LT-V/PT

PIC32MX570F512LT-V/PT - 32-bit MCU, 512KB Flash, USB/CAN, 100-TQFP

The Microchip Technology PIC32MX570F512LT-V/PT is a 32-bit MIPS32 M4K PIC microcontroller with 512KB Flash, 64KB RAM, USB 2.0 Full-Speed, CAN 2.0B, and three analog comparators in a 100-pin TQFP package rated for the automotive -40C to +105C temperature range. It is part of the AEC-Q100 qualified PIC32MX5xx family engineered for graphics, audio, and connected-embedded designs. A PIC32MX microcontroller is a 32-bit MIPS-based MCU within the broader PIC microcontroller family, bridging 8/16-bit PIC legacy code to 32-bit application processors. It belongs to the power-management-aware embedded MCU category, sitting between 8-bit MCUs and Cortex-M application processors, and integrates Flash, SRAM, and peripherals into a single chip optimized for deterministic real-time control plus moderate connectivity. Key features include 50 MHz/83 DMIPS core performance, two I2S audio ports for codec interfacing, four SPI modules, I2C, five 16-bit timers, a 10-bit 1 Msps ADC with up to 48 channels, a Parallel Master Port (PMP) with dual buffers for graphics, Peripheral Pin Select (PPS) for flexible pin mapping, and a Charge Time Measurement Unit (CTMU) for capacitive touch sensing. The USB 2.0 Full-Speed device/host/OTG controller and CAN 2.0B module enable industrial and automotive networking. The PIC32MX570F512L uses a 5-stage MIPS M4K pipeline with hardware multiply/divide and a single-cycle Flash prefetch, delivering 83 DMIPS at 50 MHz while drawing roughly 30 mA active. The 100-TQFP (12x12 mm) package provides 78 user I/O through PPS remapping, allowing peripheral-to-pin reassignment at runtime. The integrated 8 MHz FRC with PLL supports operation down to 2.3V. Typical applications include automotive infotainment HMI, USB peripherals, CAN-based industrial control, audio playback with I2S codecs, and capacitive touch HMI panels. The AEC-Q100 grade -V (-40C to +105C) plus CTMU makes it well-suited for harsh-environment HMI where commercial-grade parts fail. When designing, allocate I/O early because PPS remaps only a subset of pins; verify the specific peripheral-to-pin mapping for each design. Place the 0.1 uF decoupling network close to every VDDCORE/VSS pair, and follow the Microchip reference layout for the USB differential pair to meet USB 2.0 signal-integrity compliance. This page synthesizes AEC-Q100 cross-reference data, distributor pricing snapshots, and 100-TQFP drop-in alternatives for PIC32MX570F512LT-V/PT - insights that streamline sourcing for automotive HMI and industrial-control designs.

USD $4.82 재고 있음

PIC32MX575F256H-80I/MR

PIC32MX575F256H-80I/MR - 32-bit MCU 256KB Flash 80MHz 64-VQFN | Microchip

The Microchip Technology PIC32MX575F256H-80I/MR is a 32-bit microcontroller built on the MIPS32 M4K core, running up to 80 MHz (105 DMIPS) with 256 KB of program Flash and 64 KB of SRAM, housed in a 64-pin VQFN (MR) 9x9 mm package with exposed thermal pad. It integrates USB 2.0 On-The-Go with on-chip PHY, a CAN 2.0B module, 16-bit Parallel Master Port, 10-bit ADC, and dedicated DMA for USB OTG, targeting embedded designs that need rich connectivity in a single chip. The -80I suffix denotes the 80 MHz speed grade and the -40C to +85C industrial temperature range, while the /MR suffix marks the 64-VQFN 9x9 mm lead-free package. A 32-bit PIC32 microcontroller is a member of the MIPS-based MCU family that occupies the high-performance tier of Microchip's product hierarchy: PIC10/12/16 -> PIC24/dsPIC -> PIC32 -> Cortex-M class (competing). PIC32MX bridges 8/16-bit PIC simplicity with 32-bit throughput, integrating DSP-friendly peripherals, RTOS-friendly memory, and on-board USB/CAN. Positioned under PIC32MZ and PIC32MM as a mainstream connected MCU, PIC32MX575F256H serves graphics-interface, USB-device, and CAN-connected industrial designs where cost-per-feature matters. Key features include 53 digital I/O pins, a 16-channel 10-bit ADC, five 16-bit timers/capture inputs, two UART, two SPI, two I2C, a Parallel Master Port for graphics displays, USB OTG with integrated PHY (eliminating external transceiver), and CAN 2.0B with 1024-message buffers. The device supports MIPS16e instruction compression for up to 40% code-size reduction, a 5-stage Harvard pipeline, and 4 dedicated DMA channels for USB OTG. Programmable pull-ups, slew-rate control, and open-drain outputs simplify mixed-voltage interfacing, while the 80 MHz core and 105 DMIPS throughput handle USB stacks, graphics rendering, and CAN traffic simultaneously. Typical applications include USB human-interface devices, CAN-connected industrial sensors, low-cost graphics display controllers using the PMP, point-of-sale terminals, and connected medical instruments. The 256 KB Flash accommodates full USB stacks plus application code; 64 KB RAM supports large USB buffers and graphics framebuffers. Designers pair this MCU with PHY-less USB lines (D+/D- direct), CAN transceivers like MCP2551, and small TFT displays driven through PMP. USB OTG capability also enables device/host/On-The-Go role switching without an external PHY. When designing with this device, ensure 3.3V supply (2.5-3.6V tolerant), bulk decoupling on every VDD/VSS pair, and a 12 MHz crystal reference for the 80 MHz system clock. The exposed pad on the VQFN-64 must be soldered to a thermal/ground pour. Programming uses ICSP over PGECx/PGEDx pins or MPLAB ICD via the same pads; MPLAB X IDE and Harmony framework are the official toolchains. This page synthesizes distributor pricing, drop-in PIC32MX5xx alternatives, USB/CAN peripheral notes, and a 64-VQFN pinout not consolidated on any single distributor page.

USD $5.27 재고 있음

PIC32MX575F256H-80I/PT

PIC32MX575F256H-80I/PT - 80MHz 32-bit MCU 256KB Flash | Microchip

The Microchip Technology PIC32MX575F256H-80I/PT is a 32-bit MIPS32 M4K RISC microcontroller delivering 80 MHz performance with 256 KB Flash and 64 KB SRAM in a 64-pin TQFP (PT) 10x10 mm package. It integrates USB 2.0 full-speed, CAN 2.0b, 10-bit ADC, and a parallel graphics interface for human-machine interface designs. A PIC32 microcontroller belongs to the 32-bit MCU (microcontroller unit) family, which sits in the embedded processing hierarchy above 8-bit and 16-bit microcontrollers. Within Microchip's portfolio, PIC32MX devices target general-purpose 32-bit applications using the MIPS32 instruction set, sitting above PIC16 and PIC24/dsPIC families and below the higher-performance PIC32MZ family. The 32-bit core enables more complex software stacks, larger memory addressing, and richer peripheral integration than legacy 8/16-bit MCUs, while keeping deterministic real-time behavior. Key features include 256 KB Flash, 64 KB SRAM, USB 2.0 full-speed OTG, CAN 2.0b, up to eight 16-bit timers, a 10-bit 1 Msps ADC with up to 16 channels, I2S for audio, and a PMP parallel master port for graphics. The 64-pin TQFP 10x10 mm package offers manageable PCB area with 0.5 mm pitch for hand-prototyping or low-density layouts, and the -80I industrial temperature grade supports -40C to +85C operation. The M4K core uses a 5-stage pipeline with single-cycle multiply, hardware divide, and a configurable prefetch/cache controller that mitigates Flash wait-state penalties at 80 MHz. The 16 KB instruction cache and prefetch module accelerate tight loops in DSP-style filtering and motor-control code, while the bus matrix keeps USB, CAN, DMA, and the PMP concurrent. Typical applications include USB peripherals, industrial CAN nodes, low-cost graphics HMI panels, audio playback with I2S DACs, and bridges between legacy industrial sensors and modern USB hosts. It is also used in entry-level embedded web servers and POS terminals. When designing, validate that the 3.3V rail meets the 2.3-3.6V supply window, keep oscillator traces short, and reserve a robust decoupling network around the VDD/VSS pairs. Use Microchip MPLAB Harmony or MCC for peripheral configuration to avoid register-level misconfiguration. This page synthesizes distributor pricing, drop-in alternatives in the same TQFP-64 footprint, and practical design notes not aggregated on the manufacturer datasheet alone.

USD $7.46 재고 있음

PIC32MX575F256HT-80I/PT

PIC32MX575F256HT-80I/PT - 80MHz 32-bit MCU 256KB Flash USB/CAN | Microchip

The Microchip Technology PIC32MX575F256HT-80I/PT is a 32-bit MIPS32 M4K PIC microcontroller operating at 80 MHz with 256 KB Flash and 64 KB SRAM in a 64-pin TQFP (10x10 mm) package. It integrates a full-speed USB 2.0 device/host/OTG controller, a CAN 2.0B module, 10-bit ADC with 16 channels, and a rich set of timers and serial peripherals. This -I variant is rated for the industrial -40C to +85C operating range. A microcontroller (MCU) is a single-chip computer that integrates a CPU core, program memory (Flash), working memory (RAM), and programmable I/O peripherals onto one die. The PIC32 family extends the legacy PIC architecture to a 32-bit MIPS32 M4K core, delivering MIPS-class performance (~1.5 DMIPS/MHz) while preserving the familiar PIC toolchain (MPLAB X IDE, Harmony, XC32 compiler). Within the broader taxonomy, a PIC32 MCU is a microcontroller -> embedded processor -> semiconductor -> integrated circuit. Key features include 256 KB Flash with self-programming support, 64 KB SRAM, 53 digital I/O pins, 5 timers, 6 SPI/I2S, 6 UART, 3 I2C, a parallel master port (PMP) for graphics, and DMA for low-CPU-overhead data movement. The integrated USB 2.0 full-speed transceiver, CAN 2.0B controller, and 10-bit 1 MSPS ADC simplify designs that previously required multiple companion chips. Architecturally, the device uses a 5-stage pipeline MIPS32 M4K core, a multi-vector interrupt controller, and a peripheral bus that supports direct memory access between peripherals and SRAM. This combination allows deterministic interrupt latency even with USB and CAN traffic active - a key requirement for industrial fieldbus nodes and consumer USB peripherals. The F variant suffix denotes the 256 KB Flash density tier within the PIC32MX5xx/6xx/7xx family. Typical applications include USB peripherals (HID, CDC, MSD, audio class), CAN-based industrial nodes, graphics HMI with the PMP bus, sensor aggregation, and consumer audio devices. The wide peripheral set also makes the device suitable for retrofitting older 16-bit PIC24/PIC32 designs where USB or CAN is needed without going to a Cortex-M part. When designing with this device, plan for a 3.3V single supply (2.3V to 3.6V tolerant) and provision decoupling per the family datasheet. The two ICSP/ICD pins (PGECx, PGEDx) must be routed with short traces and pull-ups to enable in-circuit programming and MPLAB debugger operation. This page synthesizes distributor pricing, drop-in same-package alternatives, and design notes not found in a single manufacturer datasheet, giving procurement and firmware engineers a single-source reference.

USD $4.89 재고 있음

PIC32MX575F256HT-80V/MR

PIC32MX575F256HT-80V/MR - 80MHz 32-bit MCU 256KB Flash | Microchip

The Microchip PIC32MX575F256HT-80V/MR is a 32-bit MIPS M4K microcontroller running at 80 MHz with 256 KB of Flash program memory and 64 KB of SRAM, housed in a 64-pin VQFN (9x9 mm) package. It integrates USB-OTG, a 10-bit ADC, and a CAN 2.0B controller, making it a high-integration option for embedded applications requiring both connectivity and analog conversion. The device is part of the PIC32MX5xx family targeting industrial and consumer designs. A microcontroller (MCU) is a single-chip computer containing a CPU core, program memory (Flash), data memory (RAM), and a range of integrated peripherals such as timers, ADCs, communication interfaces, and GPIO. The PIC32MX5xx line uses the MIPS32 M4K 32-bit core, providing significantly higher compute throughput than 8-bit or 16-bit MCUs while retaining Microchip's PIC ecosystem (MPLAB X IDE, Harmony framework, PICkit programmers). Within the broader taxonomy, the PIC32MX sits in the hierarchy MCU -> 32-bit MCU -> MIPS-based MCU -> Microchip PIC32MX family. Key features of this variant include 256 KB Flash, 64 KB SRAM, 80 MHz core clock, USB-OTG full-speed, CAN 2.0B active, 16-channel 10-bit ADC, five 16-bit timers, and four UART/SPI/I2C modules. The -80V suffix denotes the 2.3-3.6 V VDD industrial-grade operating range with V temperature grade, while the HT suffix indicates tape-and-reel packaging for the VQFN-64. Typical applications include USB peripherals, CAN-based industrial nodes, embedded control with analog sensing, and graphical user interfaces. The integrated USB-OTG and CAN make this part well-suited for connected industrial nodes and USB device classes such as CDC, HID, and MSD. When designing with this MCU, allocate adequate PCB area for the 9x9 mm VQFN thermal pad (mandatory for power dissipation), follow Microchip's decoupling guidelines (100 nF + bulk on VDD), and use the MPLAB Harmony configurator to avoid register-level configuration errors. This page synthesizes distributor pricing, same-package drop-in alternatives, and practical design notes not found in the manufacturer datasheet.

USD $4.78 재고 있음

PIC32MX575F256L-80I/BG

PIC32MX575F256L-80I/BG - 80MHz 256KB Flash MCU | Microchip

The Microchip PIC32MX575F256L-80I/BG is a 32-bit MIPS32 M4K PIC microcontroller operating at up to 80 MHz with 256 KB Flash and 64 KB SRAM, housed in a 121-pin TFBGA (10x10 mm, 0.8 mm pitch) package. A PIC32MX microcontroller is a high-performance 32-bit Flash MCU family from Microchip built on the MIPS32 M4K core, designed for embedded applications requiring USB, CAN, and Ethernet connectivity. The PIC32MX5xx/6xx/7xx sub-family sits between the lower-pin-count PIC32MX1/2/3/4/5 series and the higher-end PIC32MX7xx graphics-enabled parts, targeting connected-embedded designs that need rich peripherals and moderate code/data density. Architecturally, the PIC32MX570/575/675/795 line bridges 8-bit PIC migration paths and full Linux-capable processors. Key features include 256 KB Flash program memory, 64 KB SRAM, full-speed USB 2.0 device/host/OTG, one CAN 2.0B controller, 10/100 Mbps Ethernet MAC, up to 83 general-purpose I/O pins, five 16-bit timers/counters, sixteen 10-bit ADC channels at 1 Msps, and two analog comparators. The 121-ball TFBGA package provides high pin density at 0.8 mm pitch with a compact 10x10 mm footprint for space-constrained designs. Industrial temperature range (-40C to +85C) is supported. The PIC32MX575F256L uses the MIPS32 M4K core with 5-stage pipeline, single-cycle multiply, hardware multiply-accumulate, and an 8-deep prefetch cache. Peripheral bus and instruction RAM are tightly coupled to allow deterministic interrupt response, while the DMA controller with eight channels offloads data movement between peripherals and memory for streaming USB, CAN, and Ethernet traffic. Typical applications include USB peripherals, CAN-based industrial nodes, Ethernet-connected embedded devices, industrial control and HMI, point-of-sale terminals, and medical instrumentation. The combination of full-speed USB, CAN, and 10/100 Ethernet makes the PIC32MX575F256L well suited to multi-protocol gateway designs. When designing, plan for 2.5V/3.3V core operation, follow Microchip's TFBGA PCB layout and decoupling guidelines for high-pin-count BGA packages, and allocate sufficient code space for the TCP/IP stack (e.g., Microchip Harmony) when Ethernet is used. The pre-fetch cache must be enabled for code in flash to achieve 80 MHz performance. This page synthesizes distributor pricing from DigiKey, Mouser, LCSC and Newark, drop-in same-package alternatives drawn from the same PIC32MX5xx family, and practical design notes not found in the manufacturer datasheet.

USD $6.12 재고 있음

PIC32MX575F256L-80V/BG

PIC32MX575F256L-80V/BG - 80MHz 32-bit MCU 256KB Flash | Microchip

The Microchip PIC32MX575F256L-80V/BG is a 32-bit MIPS M4K microcontroller operating at 80 MHz with 256 KB of Flash and 64 KB of SRAM, integrated USB-OTG, CAN, and 10-bit ADC peripherals in a 121-ball TFBGA (10x10 mm) package. Designed for embedded applications that demand high-performance compute and connectivity, it combines deterministic interrupt latency with rich peripheral integration including USB-OTG, CAN 2.0B, I2C, SPI, and UART interfaces. A 32-bit microcontroller (MCU) is an integrated circuit containing a CPU core, program memory, data memory, and multiple peripheral interfaces on a single die. Within the embedded hierarchy, an MCU sits below a microprocessor (MPU) in scope - the MCU integrates memory and peripherals, whereas an MPU requires external components. The PIC32MX family belongs to Microchip's MIPS-based 32-bit MCU portfolio, engineered as a high-performance upgrade path for designers using PIC24/dsPIC devices who need additional throughput and full-speed USB connectivity. The PIC32MX575F256L-80V/BG executes most instructions in a single cycle due to its 5-stage pipeline Harvard architecture, achieving 1.56 DMIPS/MHz. On-chip memory includes 256 KB Flash with pre-fetch cache and 64 KB SRAM, providing sufficient headroom for protocol stacks such as USB, TCP/IP, and CAN. The integrated 10-bit ADC with up to 16 channels supports conversion rates up to 1 Msps, while the parallel master port enables connection to external graphics or memory devices without glue logic. Typical applications include industrial automation controllers with USB diagnostics, automotive body and comfort modules requiring CAN connectivity, USB-enabled medical devices such as blood-pressure monitors, and embedded HMI designs that need both USB and CAN for system integration. Its wide operating temperature range and dual communication interfaces make it especially useful where fieldbus and PC-side enumeration must coexist on the same node. When designing with this device, allocate at least one decoupling capacitor per power pin pair (0.1 uF X7R ceramic) within 3 mm of the supply balls. For USB-OTG designs, the 90-ohm differential pair must be routed as a matched-length, impedance-controlled pair with a continuous reference ground plane. The -80V speed grade specifies the 80 MHz industrial temperature range (-40C to +105C); the -80I variant offers the wider -40C to +125C grade for harsher environments. This page consolidates distributor pricing, drop-in same-package alternatives from the PIC32MX5 family, application notes for USB and CAN, and PCB layout guidance not typically compiled in the manufacturer datasheet. Engineers can compare same-footprint parts side-by-side and select a variant that matches the required temperature grade without redesigning the PCB.

USD $5.07 재고 있음

PIC32MX575F256L-80V/PF

PIC32MX575F256L-80V/PF - 80MHz 32-bit MCU 256KB Flash | Microchip

The Microchip PIC32MX575F256L-80V/PF is a 32-bit MIPS MCU from the PIC32MX5XX/6XX/7XX family, integrating 256 KB Flash, 64 KB SRAM, full-speed USB-OTG, CAN, and a 10-bit ADC, housed in a 100-pin TQFP (14x14 mm) package rated -40C to +105C. It executes instructions at 80 MHz from the MIPS32 M4K core while delivering 1.56 DMIPS/MHz and supporting 5-stage pipeline execution, DMA, and parallel master port for high-throughput embedded designs. A 32-bit microcontroller (MCU) is a single-chip computer that integrates a 32-bit processor core, program memory (Flash), data memory (SRAM), and peripherals such as timers, communication controllers, and analog blocks. The PIC32MX575 belongs to the PIC32 family which occupies the high-performance tier of Microchip's MCU portfolio, sitting above PIC24/dsPIC and below the SAME70/SAM Cortex-M7 series in terms of capability. Key differentiating features include USB-OTG with on-chip transceiver (no external PHY required), a dedicated CAN 2.0B module for industrial networking, five 16-bit timers/captures, four UART/SPI/I2C pairs, a 16-channel 10-bit 1 Msps ADC, and a Parallel Master Port for external bus expansion. The integrated DMA controller offloads data movement from the CPU, enabling deterministic throughput for USB and CAN traffic. JTAG and 2-wire trace ports are provided for the MPLAB REAL ICE / ICD 3 debug ecosystem. Typical applications span industrial automation (CAN nodes, sensor hubs), USB peripherals (human-interface devices, data loggers, instrumentation), and embedded networking gateways that benefit from the simultaneous USB device/host and CAN support. The PIC32MX575F256L is also a strong fit for point-of-sale terminals and medical instrumentation where deterministic performance and ample code space are required. Designers should note the 2.5V/3.3V dual-rail requirement (core on VCAP/VDD, I/O on VDDIO), the need for proper 8 MHz primary oscillator configuration in MPLAB Harmony, and that the V variant indicates -40C to +105C operation. Compared to the lower-density PIC32MX360/PIC32MX440 series, this device adds USB-OTG, full CAN, and a parallel master port at similar clock rates. This page consolidates distributor pricing for PIC32MX575F256L-80V/PF, drop-in same-family alternatives, and engineering design notes not duplicated from the manufacturer datasheet.

USD $6.55 재고 있음

PIC32MX575F256LT-80I/BG

PIC32MX575F256LT-80I/BG - 80MHz 32-bit MCU 256KB Flash TFBGA-121

The Microchip Technology PIC32MX575F256LT-80I/BG is a 32-bit MIPS32 M4K microcontroller operating at up to 80 MHz with 256 KB of Flash and 64 KB of SRAM, housed in a 121-ball TFBGA (10 mm x 10 mm) package. This industrial-temperature grade device integrates a USB 2.0 full-speed device/host/OTG controller, a CAN 2.0B module, and a 10-bit ADC, making it a single-chip solution for connected embedded designs. A microcontroller (MCU) is a programmable system-on-chip that combines a CPU core, memory, and peripherals to execute embedded firmware in real time. The PIC32MX family extends this concept with a 32-bit MIPS core that delivers significantly higher computational throughput than 8-bit or 16-bit MCUs, while maintaining deterministic interrupt behaviour. Within the wider taxonomy, this part belongs to: microcontroller -> 32-bit MCU -> MIPS MCU -> PIC32MX family -> USB-and-CAN enabled tier. Key features include 256 KB (256K x 8) of in-system self-programmable Flash, 64 KB of SRAM, 53 general-purpose I/O pins, multiple UART, SPI, and I2C peripherals, and a 16-bit parallel master port for external memory or graphics interfacing. The integrated USB 2.0 full-speed transceiver supports device, host, and OTG operation, removing the need for an external PHY in many designs. Typical applications include industrial control with CAN-bus connectivity, USB peripherals such as HID and CDC devices, graphical HMI panels using the parallel master port, embedded data loggers, and low-cost USB-to-UART bridges. The wide operating voltage of 2.5 V to 3.6 V and industrial temperature range of -40 C to +85 C suit factory-floor and outdoor installations. When designing with this part, ensure the TFBGA-121 land pattern meets IPC-7351 ball-pitch tolerances and that decoupling is placed within 2 mm of each power ball. For new designs, also evaluate the newer PIC32MX1xx/2xx families for lower power consumption and the PIC32MK family for higher performance. This page synthesises verified distributor pricing, parametric drop-in alternatives from the same PIC32MX family, and practical design notes not aggregated on a single manufacturer page.

USD $5.95 재고 있음

PIC32MX575F256LT-80I/PF

PIC32MX575F256LT-80I/PF - 80MHz 32-bit MCU 256KB Flash USB/CAN | Microchip

The Microchip Technology PIC32MX575F256LT-80I/PF is a 32-bit MIPS M4K microcontroller with 256 KB Flash and 64 KB SRAM, integrated USB 2.0 full-speed and CAN 2.0B peripherals, eight DMA channels, and a 100-pin TQFP (PF) package. It operates up to 80 MHz core clock from a 2.3V to 3.6V supply. A 32-bit microcontroller (MCU) is a programmable integrated circuit that executes instructions from on-chip Flash memory using a 32-bit data path, dramatically outperforming 8- and 16-bit MCUs on DSP and arithmetic workloads. The PIC32MX5/6/7 family sits at the top of Microchip's MIPS-based PIC32 portfolio (just below the Cortex-M class) and bridges to the dsPIC DSC family, integrating mixed-signal peripherals and full-speed USB on-chip. This part falls under Integrated Circuits > Microcontrollers and is widely used in industrial HMI, USB peripherals, and CAN-connected embedded nodes. Key features include 256 KB Flash (256K x 8), 64 KB SRAM, USB 2.0 full-speed On-The-Go, one CAN 2.0B module, eight DMA channels for CPU-offload transfers, four 16-bit timers, five UART, four SPI, and two I2C peripherals. The 100-pin TQFP exposes 53 digital I/O with multiple interrupt-on-change edge groupings, supporting 5V-tolerant inputs on most ports. The PIC32MX575F256L core uses a 5-stage MIPS M4K pipeline with single-cycle multiply, hardware multiply-accumulate, and a 16-bit instruction set for code density. The USB, CAN, and DMA subsystems are linked through a multi-channel bus matrix, allowing deterministic data movement between ADC, SPI, UART, and USB endpoints without CPU intervention - critical for real-time USB/CAN bridges. Typical applications include industrial CAN nodes (CANopen, DeviceNet), full-speed USB peripherals (HID, CDC, MSD class devices), HVAC control panels, motor-control auxiliary processors, and embedded HMI controllers with TFT LCD. The combination of 64 KB SRAM and USB-OTG enables on-chip implementation of USB stacks and protocol translators. When designing with this device, note the operating voltage of 2.3V to 3.6V - a 3.3V LDO is the standard supply. Place 0.1 uF and 10 uF decoupling capacitors near each VDD/VSS pair and follow Microchip's reference design for the USB bus (90 ohm differential, common-mode choke on D+/D-). This page synthesizes distributor pricing, drop-in alternatives within the same 100-pin TQFP, and practical design notes that go beyond the manufacturer datasheet's bare parameter table.

USD $4.85 재고 있음

PIC32MX575F256LT-80I/PT

PIC32MX575F256LT-80I/PT - 32-bit 80MHz MCU 256KB Flash USB CAN | Microchip

The Microchip PIC32MX575F256LT-80I/PT is a 32-bit MIPS MCU running at 80MHz with 256KB Flash and 64KB RAM in a 100-pin TQFP (12x12) package. It integrates USB OTG, CAN, and a 16-channel 10-bit ADC. An MCC product line is a class of high-performance microcontrollers built around the MIPS32 M4K core, designed for embedded applications that require more processing power than 8/16-bit MCUs while retaining peripheral integration. The PIC32MX5/6/7XX family supports USB, CAN, and Ethernet connectivity, suiting industrial, consumer, and automotive subsystems where deterministic interrupt latency and a rich peripheral set are required. Key features include 256KB Flash (256K x 8), 64KB RAM, 85 I/O pins, and 16-channel 10-bit ADC. The device integrates USB OTG full-speed, one CAN module, SPI, I2C, and UART. DMA, PMP, and a 5-bit RTCC are also present, and the part runs from 2.3V to 3.6V across the industrial -40C to +85C range. Architecturally the M4K core delivers 1.56 DMIPS/WMC with single-cycle bit-shaded math and hardware multiply/divide, easing protocol parsing and DSP-style loops. Five 16-bit timers/capture/compare and two comparators/PWM modules complement the timers, allowing closed-loop motor and power-conversion control. Code execution is from Flash with a prefetch module that hides Flash access latency. Typical applications include industrial automation, USB peripherals, automotive CAN nodes, and graphic display HMIs. The wide peripheral mix also suits barcode scanners, point-of-sale terminals, and home medical monitors. The PIC32MX575F256LT-80I/PT is supported by MPLAB X IDE, XC32 compiler, and PICkit 5 debugger. For power, plan decoupling at each VDD/VSS pair and route the analog AVdd/AVss pair through a ferrite to reduce ADC noise. This page combines current distributor pricing, drop-in alternatives within the PIC32MX5XX family, and engineering design notes not found in the manufacturer datasheet.

USD $4.35 재고 있음

PIC32MX575F256LT-80V/BG

PIC32MX575F256LT-80V/BG - 256KB Flash 32-bit MCU | Microchip

The Microchip Technology PIC32MX575F256LT-80V/BG is a 32-bit RISC microcontroller based on the MIPS32 M4K core, featuring 256 KB of Flash program memory and 64 KB of SRAM, operating at up to 80 MHz. Housed in a 121-pin TFBGA (10x10 mm) package, this part integrates USB-OTG, CAN, and a 10-bit ADC, making it suitable for embedded applications requiring connectivity and moderate analog performance. A microcontroller (MCU) is a single-chip computer that integrates a CPU core, memory (Flash for program code and SRAM for data), and a rich set of peripherals such as timers, communication interfaces, and analog blocks. The PIC32 family sits within the broader taxonomy: microcontroller -> embedded processor -> semiconductor -> integrated circuit. Within Microchip's portfolio, PIC32MX5xx devices target mainstream 32-bit embedded designs that exceed 8-bit PIC16/PIC18 capability without the cost of higher-tier PIC32MZ parts. Key features of this device include 83 general-purpose I/O lines, multiple DMA channels for peripheral-to-memory transfers without CPU intervention, PWM outputs for motor and power control, and a 10-bit ADC with 1 Msps sampling. It also provides two I2C, two SPI, and two UART interfaces for flexible peripheral connectivity. Technically, the MIPS32 M4K core delivers 1.56 DMIPS/MHz and supports the MIPS16e instruction set for code density. The 5-stage pipeline and hardware multiply/divide unit accelerate DSP-style operations. The 80 MHz operation yields 105 DMIPS, while the USB-OTG and CAN peripherals are critical for industrial networking and consumer device bridging. Typical applications include USB peripherals, CAN-connected industrial nodes, graphical user interfaces with external LCD controllers, motor control loops, and consumer audio devices. Designers select this part when balancing Flash size, peripheral set, and cost. The TFBGA package supports compact PCB layouts but requires careful routing due to the 0.8 mm pitch. When designing, ensure proper decoupling near each VDD/VSS pair, and verify the 80 MHz timing closure with the chosen compiler optimization. The -80V suffix indicates the 80 MHz speed grade and 'V' temperature range; the 'BG' suffix indicates the 121-pin TFBGA package and tape-and-tray packaging. This page synthesizes distributor pricing, drop-in alternatives, and practical design notes not found on standalone datasheet or distributor pages.

USD $6.84 재고 있음

PIC32MX575F256LT-80V/PF

PIC32MX575F256LT-80V/PF - 32-bit 80MHz MCU, 256KB Flash, USB-OTG, CAN | Microchip

The Microchip Technology PIC32MX575F256LT-80V/PF is a 32-bit MIPS32 M4K microcontroller operating at up to 80 MHz with 256 KB of Flash program memory and 64 KB of SRAM, housed in a 100-pin TQFP (14x14 mm) package. It integrates full-speed USB-OTG, a CAN 2.0B controller, a 10-bit 1 Msps ADC, multiple UART/SPI/I2C peripherals, DMA channels, and PWM outputs, making it a high-integration MCU for embedded connectivity designs. The supply voltage range is 2.3 V to 3.6 V, with 83 general-purpose I/O lines supporting 5V-tolerant inputs. A 32-bit microcontroller (MCU) is an integrated computing system on a single silicon die containing a high-performance processor core, program and data memory, and a rich set of on-chip peripherals. Within the broader taxonomy, PIC32MX devices belong to the microcontroller (MCU) class, which sits under microcontrollers -> embedded processors -> semiconductors. The PIC32MX5XX/6XX/7XX family leverages the MIPS32 M4K core licensed from Imagination/MIPS, providing single-cycle multiply and hardware multiply-accumulate for DSP-style workloads while remaining code-compatible with the Microchip MPLAB XC32 toolchain. Key features include 256 KB Flash organized as 256K x 8, 64 KB SRAM, 80 MHz maximum core clock with 1.56 DMIPS/MHz performance, full-speed USB 2.0 OTG with on-chip transceiver, CAN 2.0B active controller, a 16-channel 10-bit ADC with 1 Msps conversion rate, five UART/SPI/I2C peripherals configurable through PPS (Peripheral Pin Select), an 8-channel DMA controller, and five 16-bit timers/capture/compare/PWM modules. The wide-pin TQFP-100 package enables flexible PCB routing and full peripheral pin-out. The architecture combines a 5-stage pipeline MIPS core with hardware multiply/divide, a tightly-coupled prefetch module that issues Flash accesses 128 bits per cycle, and dedicated peripherals connected via a multi-layer bus matrix. This design yields deterministic interrupt latency and high throughput for USB and CAN stacks while keeping active power consumption in the tens of milliamps at 80 MHz. Typical applications include industrial control and HMI panels, USB peripherals (CDC/HID/MSD), CAN-bus nodes in automotive and industrial automation, low-cost graphics and TFT display controllers, sensor aggregation hubs, and portable medical or instrumentation devices. The combination of native USB-OTG and CAN makes it particularly suited to networked embedded devices. When designing with this part, carefully allocate the Peripheral Pin Select (PPS) mapping before committing the PCB layout, and place a 32.768 kHz secondary crystal if the USB module requires SOF synchronization or RTC accuracy. Adequate decoupling (100 nF + 4.7 µF bulk) close to each power pin is mandatory for reliable 80 MHz operation. This page synthesizes distributor pricing, drop-in pin-compatible alternatives from Microchip's PIC32 family, and practical design notes not found in the standalone datasheet, helping engineers compare options quickly.

USD $5.65 재고 있음

PIC32MX575F256LT-80V/PT

PIC32MX575F256LT-80V/PT - 80MHz 256KB Flash 32-bit MCU | Microchip

The Microchip Technology PIC32MX575F256LT-80V/PT is a 32-bit RISC microcontroller built on the MIPS32 M4K core, delivering up to 80 MHz CPU performance with 256 KB of Flash program memory and 64 KB of SRAM, housed in a 100-pin TQFP (12x12 mm) package. It integrates USB-OTG, CAN, and a 10-bit ADC, positioning it as a high-performance mixed-signal MCU for embedded connectivity applications. A microcontroller (MCU) is a single-chip computer containing a CPU core, program and data memory, and integrated peripherals including ADCs, timers, and communication controllers. The PIC32MX5XX/6XX/7XX family sits in the hierarchy as: microcontroller -> embedded computing -> semiconductor, and bridges 8-bit PIC16/PIC18 simplicity with 32-bit performance, targeting USB/CAN-enabled industrial, medical, and consumer devices. Key features of the PIC32MX575F256LT-80V/PT include 83 general-purpose I/O lines, 16-channel 10-bit ADC at 1 Msps, multiple DMA channels for low-CPU-overhead data movement, hardware RTCC, 5 timer/counter modules, and peripheral pin select (PPS) for flexible signal routing. The "V" suffix denotes the V-temp grade of -40C to +105C operation, suitable for industrial environments; the "T" denotes tape-and-reel packaging; and the "/PT" denotes the 100-pin TQFP package. Architecturally, the PIC32MX575 uses the MIPS32 M4K core with 5-stage pipeline, single-cycle multiply, and hardware divide. It supports 32-bit instructions and 32-bit data paths while remaining code-compatible with legacy 16-bit PIC instruction extensions. The M4K core combined with tightly-coupled DMA offloads data transfers from the CPU for deterministic latency. Typical applications include USB peripherals (HID, CDC, mass storage), CAN-connected industrial nodes, motor control (BLDC, stepper, servo), graphical HMI with external LCD controllers, and sensor data acquisition. The integrated USB-OTG and CAN make it especially suitable for industrial automation, medical instrumentation, and automotive body/comfort subsystems. When designing with this part, mind the 2.3V-3.6V supply range and ensure decoupling caps are placed per the datasheet. PPS requires careful pin mapping during firmware bring-up; verify PPS assignments in code review to avoid silent peripheral failures. This page consolidates distributor pricing, drop-in alternatives, and design notes not found in the manufacturer datasheet.

USD $5.05 재고 있음

PIC32MX575F512H-80I/MR

PIC32MX575F512H-80I/MR - 32-bit 80MHz 512KB Flash MCU | Microchip

The Microchip Technology PIC32MX575F512H-80I/MR is a 32-bit MIPS M4K PIC microcontroller running at 80 MHz, integrating 512 KB of Flash program memory and 64 KB of SRAM into a 64-pin VQFN (9x9 mm, MR package). The -80I/MR suffix indicates an 80 MHz maximum operating frequency, industrial temperature grade (-40C to +85C), and the MR VQFN-64 package with an exposed thermal pad for surface-mount reflow. A PIC32MX microcontroller is a high-performance 32-bit MCU family from Microchip built on the MIPS M4K core. PIC32 sits in the broader taxonomy: microcontroller -> 32-bit MCU -> MIPS MCU -> PIC32MX family -> embedded SoC. The 32-bit datapath, dedicated USB 2.0 full-speed On-The-Go (OTG) controller, hardware CAN 2.0B module, and integrated 10/100 Ethernet MAC make PIC32MX5XX/6XX/7XX devices well suited to connected embedded designs that previously required external PHY/bridges or a separate communication companion chip. Key features of the PIC32MX575F512H variant include 512 KB Flash, 64 KB SRAM, 51 general-purpose I/O pins, a 16-channel 10-bit ADC at up to 1 Msps, two UARTs, two SPI/I2S ports, two I2C ports, four 16-bit timers plus one 32-bit RTCC timer, five PWM/OC channels, and a parallel master port (PMP) for off-chip memory or graphics interfacing. The device operates from 2.3 V to 3.6 V, has a maximum CPU clock of 80 MHz, and supports 105 DMIPS throughput with single-cycle MAC hardware. The architecture combines a Harvard-style 5-stage pipeline, prefetch cache to mitigate Flash wait states, and a rich peripheral set. The USB OTG controller with integrated PHY eliminates external USB transceivers, the CAN module complies with CAN 2.0B active, and the Ethernet MAC supports RMII/MII for 10/100 Mbps networking. Code is developed in MPLAB X IDE with MPLAB Harmony and programmed via ICSP or JTAG. Typical applications include industrial USB/CAN gateways, factory automation nodes, embedded web servers, USB peripherals, point-of-sale terminals, motor control inverters, and medical instrumentation requiring USB connectivity. The integrated peripherals allow a single chip to handle communication, user I/O, and modest signal processing without external bridges. Design with PIC32MX575F512H by first allocating a 3.3 V LDO with adequate decoupling (100 nF plus 4.7 uF bulk), then route the 8 MHz primary crystal with short traces and a guard ring to keep the PLL stable. Enable the prefetch cache module in your startup code to compensate for Flash wait states at 80 MHz. This page synthesizes distributor pricing, parametric cross-references, application notes, and practical design notes not found in the manufacturer datasheet alone - enabling faster sourcing decisions for engineers evaluating the PIC32MX575F512H-80I/MR.

USD $6.72 재고 있음

PIC32MX575F512H-80I/PT

PIC32MX575F512H-80I/PT - 80MHz MCU 512KB Flash USB/CAN | Microchip

The Microchip Technology PIC32MX575F512H-80I/PT is a 32-bit MIPS32 M4K microcontroller running at 80 MHz with 512 KB of Flash and 64 KB of SRAM, housed in a 64-pin TQFP (PT) 10x10 mm package. It integrates USB OTG and CAN connectivity alongside a rich peripheral set, making it suitable for embedded designs that demand both deterministic real-time control and high-bandwidth communication. A 32-bit microcontroller (MCU) is an integrated circuit containing a 32-bit processor core, on-chip program and data memory, plus peripheral blocks such as timers, communication controllers, and analog modules. In the component hierarchy: MCU -> microcontroller -> embedded processor -> semiconductor. The PIC32MX family sits at the high-performance end of Microchip's 32-bit portfolio, combining the MIPS M4K core with deep peripheral integration to reduce BOM cost and PCB area compared to discrete designs. Key features include 80 MHz core operation delivering 1.56 DMIPS/MHz (approximately 125 DMIPS aggregate), 512 KB Flash program memory, 64 KB SRAM, and 53 digital I/O pins. The device integrates 5 timers, 5 input capture and 5 output compare modules, 8 DMA channels for CPU-offloaded data movement, 2 analog comparators, and a USB 2.0 full-speed On-The-Go controller. Communication interfaces include 2 CAN, 5 I2C, 4 SPI, and 6 UART modules for simultaneous bus connectivity. The PIC32MX575F512H-80I/PT uses a Harvard-architecture MIPS32 M4K core with hardware multiply/divide and DSP extensions, enabling efficient signal-processing workloads. The integrated DMA controller moves data between peripherals and memory without CPU intervention, providing deterministic real-time response for control loops. The USB OTG peripheral supports both host and device roles, eliminating the need for an external PHY in low-speed designs, and the 16-bit parallel master port (PMP) can drive TFT displays directly for HMI applications. Typical applications include industrial control panels with USB diagnostics, CAN-connected automotive subsystems, USB medical devices, and embedded HMI with TFT displays. Its large memory footprint suits firmware-heavy designs running an RTOS, USB stacks, and graphics libraries concurrently. When designing with this part, ensure the 2.3 V to 3.6 V supply is well-decoupled near the IC and respect the in-circuit programming (ICSP) pin assignments. The 80I suffix denotes the industrial -40C to +85C temperature grade suitable for harsh environments. This page synthesizes distributor pricing, drop-in alternatives, and practical design notes not found in the manufacturer datasheet alone, with cross-references to the Microchip PIC32MX5XX/6XX/7XX family reference documentation.

USD $5.11 재고 있음

PIC32MX575F512H-80V/PT

PIC32MX575F512H-80V/PT - 32-bit MCU 512KB Flash 64TQFP | Microchip

The Microchip Technology PIC32MX575F512H-80V/PT is a 32-bit MIPS32 M4K microcontroller running at 80 MHz, with 512 KB on-chip Flash and 64 KB SRAM, packaged in a 64-pin TQFP (10x10 mm). It integrates USB-OTG and CAN interfaces, a 10-bit ADC up to 1 Msps, and a comprehensive peripheral set aimed at high-performance embedded designs. A PIC32MX microcontroller belongs to the 32-bit MCU category, itself a subclass of microcontrollers, which sit under the broader power management / embedded control semiconductor taxonomy. Within Microchip's portfolio, the PIC32MX5xx/6xx/7xx family targets general-purpose and connectivity-rich designs where an 8- or 16-bit MCU is too slow. The M4K core delivers 1.56 DMIPS/MHz and supports the MIPS instruction set, easing migration from PIC24/dsPIC designs while offering a clear upgrade path to MIPS M14K-based PIC32MZ devices. Key features include 512 KB Flash (plus 12 KB boot Flash), 64 KB RAM, sixteen 16-bit timers, five 16-bit capture inputs, five 16-bit compare/PWM outputs, a 10-bit 1 Msps ADC with up to 16 channels, two I2C, two SPI, and a UART. The integrated USB-OTG (full-speed) and CAN 2.0B modules eliminate the need for external connectivity ICs, reducing both BOM cost and firmware complexity. Hardware RTCC, PMP/EMG, and SQI interfaces further extend design flexibility. Operating voltage spans 2.3V to 3.6V with multiple low-power modes (Sleep, Idle, and Deep Sleep with RTCC). The Fail-Safe Clock Monitor and dual-watchdog timer architecture deliver the resilience required for IEC 60730 Class B safety-critical applications. The 64-pin TQFP package is pin-compatible with most PIC24/dsPIC devices of similar pin count, simplifying layout reuse. Typical applications include industrial USB-CAN gateways, motor-control front-ends, multi-protocol industrial sensor hubs, USB human-interface devices, and point-of-sale terminals. The 10-bit ADC and high-performance core make it suitable for digital audio bridges and motor-control applications where deterministic performance is required. When designing with this part, allocate the analog and digital supply pins (AVDD/AVSS and VDD/VSS) with proper decoupling, and verify the USB DP/DPU traces meet 90-ohm differential impedance. Programming via MPLAB X IDE with PICkit 5 or ICD 4 is recommended for production-grade in-circuit debug. This page synthesizes distributor pricing, drop-in pin-compatible alternatives, and practical design notes not found in the manufacturer datasheet alone, helping engineers evaluate the PIC32MX575F512H-80V/PT for both new designs and lifecycle refresh projects.

USD $5.30 재고 있음

PIC32MX575F512HT-80I/PT

PIC32MX575F512HT-80I/PT - 80MHz MIPS32 M4K MCU 512KB Flash | Microchip

The Microchip Technology PIC32MX575F512HT-80I/PT is a 32-bit MIPS MCU in the PIC32MX5/6/7 family that integrates a MIPS32 M4K core running up to 80 MHz (105 DMIPS), 512 KB of Flash program memory and 128 KB of SRAM, plus a USB 2.0 On-The-Go (OTG) peripheral with integrated PHY and a CAN 2.0B module. It is offered in a 64-pin TQFP (10x10 mm) package with industrial -40C to +85C temperature grade, and ships on tape and reel (the "T" suffix denotes tape-and-reel packaging, "I" denotes industrial temperature range). The device targets USB- and CAN-connected embedded designs that need ample code space, deterministic interrupt behavior, and a wide peripheral set on a 3.0 V to 3.6 V supply. A PIC32MX microcontroller is a 32-bit MCU built around the MIPS M4K core, positioned above 8-bit PIC16/PIC18 devices and below higher-end Cortex-M parts. In the system hierarchy it sits in the Microcontrollers sub-tree of Integrated Circuits and is part of the broader PIC32 family, which delivers single-cycle hardware multiply/divide, a 5-stage pipeline, and optional MIPS16e code compression that can shrink code size by up to 40 percent. These features make the PIC32MX575F512HT-80I/PT suitable for designers migrating from 16-bit MCUs who need more performance and richer connectivity without moving to an ARM-based platform. Key differentiating features include 105 DMIPS peak performance at 80 MHz, integrated USB 2.0 OTG with on-chip PHY (eliminating an external ULPI transceiver), a CAN 2.0B controller with 1024-message transmit/receive buffers, four dedicated DMA channels including one for USB OTG, plus brown-out reset, power-on reset, PWM, and up to 5 dedicated DMA channels. Compared to smaller PIC32MX parts, the 512 KB Flash / 128 KB RAM headroom enables larger protocol stacks such as USB host stacks, full TCP/IP firmware, or audio processing. Compared to PIC32MX370/PIC32MX470 devices that drop USB OTG, this part retains the integrated USB PHY for direct USB connector attachment. Typical applications for the PIC32MX575F512HT-80I/PT include USB peripherals (HID, CDC, mass storage, audio), industrial CAN nodes (CANopen, J1939), embedded web servers, sensor hubs, and human-machine interfaces with TFT displays. Designers typically use MPLAB X IDE with the MPLAB XC32 compiler and the Harmony framework to develop firmware, and debug via the MPLAB PICkit 5 or ICD 4. Plan for a stable 3.3 V rail (decoupling with 100 nF ceramic at each VDD/VSS pair plus a 10 uF bulk capacitor) and a 12 MHz primary crystal or internal oscillator reference.

USD $7.74 재고 있음

PIC32MX575F512HT-80V/MR

PIC32MX575F512HT-80V/MR - 80MHz 512KB Flash 32-bit MCU | Microchip

The Microchip PIC32MX575F512HT-80V/MR is a 32-bit MIPS MCU from the PIC32MX5 family with 512KB Flash and 64KB RAM in a 64-pin VQFN (9x9 mm) package. It integrates USB-OTG, CAN, and a 10-bit ADC, and runs the MIPS32 M4K core at up to 80 MHz. The HT suffix indicates a high-temperature (V temperature range) tape-and-reel packaged device. A 32-bit microcontroller (MCU) is a single-chip computer that integrates a CPU core, program memory (Flash), data memory (SRAM), and a rich set of peripherals (ADC, timers, communication controllers). PIC32MX5xx parts sit in the upper-mid tier of Microchip's PIC32 portfolio, balancing deterministic interrupt performance with a USB-OTG + CAN connectivity combination. The PIC32MX5 family belongs to the broader taxonomy: microcontroller -> embedded processor -> semiconductor IC. Compared to 8-bit PIC16/PIC24 devices, PIC32MX5 offers up to 80 MHz operation, M4K core, and significantly larger memory. Key differentiating features of this part include 512KB Flash (512K x 8), 64KB RAM, USB-OTG with integrated transceiver support, one CAN 2.0B module, four UART, three SPI, two I2C, a 16-channel 10-bit ADC, five 16-bit timers, and 53 selectable I/O pins. The MR suffix denotes a 64-lead VQFN package with exposed pad for thermal dissipation, while the HT suffix marks high-temperature operation at 80 MHz with tape-and-reel packaging. Architecturally, the PIC32MX575F512H combines the MIPS32 M4K Harvard core with a 5-stage pipeline, prefetch cache, and tightly-coupled peripherals designed for real-time USB and CAN workloads. The 80 MHz operation delivers 1.56 DMIPS/MHz performance per the MIPS M4K benchmark. The 64KB RAM supports dual-port DMA to peripheral buffers, which keeps USB isochronous throughput high. Typical applications include USB HID/CDC device controllers, CAN node interfaces for industrial automation, embedded HMI panels with USB touchscreens, and point-of-sale terminals. The combination of 512KB Flash, USB-OTG and CAN makes the part a strong fit for connected industrial devices that must bridge to a PC host while speaking CANopen or DeviceNet on the factory bus. When designing with this MCU, route VDD/VSS pairs to the internal exposed thermal pad to improve thermal dissipation, place a 0.0222 ohm ferrite or ferrite bead on VDD for each pair, and use the JTAG ports (TMS/TCK/TDO/TDI) for production programming. This page synthesizes distributor pricing, drop-in alternatives, and practical design notes that are not found in the Microchip datasheet alone.

USD $4.50 재고 있음

PIC32MX575F512HT-80V/PT

PIC32MX575F512HT-80V/PT - 80MHz 512KB Flash MCU | Microchip

The Microchip Technology PIC32MX575F512HT-80V/PT is a 32-bit MIPS32 M4K PIC microcontroller operating at up to 80 MHz, integrating 512 KB Flash and 64 KB RAM in a 64-pin TQFP (10x10 mm) package. It belongs to the PIC32MX5XX/6XX/7XX family of high-performance microcontrollers with USB-OTG, CAN, and 10-bit ADC peripherals. The device runs from 2.3 V to 3.6 V and is rated for the -40C to +105C automotive/industrial temperature range. A PIC32MX microcontroller is a MIPS-based 32-bit MCU that bridges the gap between 8/16-bit legacy PIC microcontrollers and higher-end ARM Cortex-M devices. Within the power-management IC hierarchy, PIC32MX belongs to the broad microcontroller category and the embedded computing branch. These devices typically include USB, CAN, Ethernet MAC, and 16-bit parallel master ports, making them suitable for connected embedded designs. Key features include single-cycle hardware multiply/divide, five 16-bit timers/counters, two I2C, two SPI, two UART, USB-OTG full-speed, CAN 2.0B, 16-channel 10-bit ADC at 1 Msps, and a parallel master port. The PIC32MX575F512H die integrates peripheral pin select for flexible routing, plus a 4-channel DMA controller for low-CPU-overhead data movement. The PIC32MX575 architecture pairs the MIPS M4K core with a multi-layer bus matrix so the CPU, DMA, and peripherals can fetch from Flash, RAM, and peripherals concurrently without contention. The 80 MHz core delivers 1.56 DMIPS/MHz or 124 DMIPS, with single-cycle 32-bit multiply for DSP-class math. An on-chip 8 MHz internal RC oscillator with PLL provides flexible clocking for USB and CAN. Typical applications include USB peripherals (HID, CDC, mass storage), CAN-based industrial control nodes, audio decoding with I2S, motor control, and graphical user interfaces with parallel LCD or OLED panels. Designers frequently pair it with the PICkit 5 debugger and MPLAB X IDE for development. When designing with this part, ensure the VDD/VSS bulk decoupling is sized for the 80 MHz core load and that the 48 MHz USB clock accuracy is maintained within 0.25 percent. The "V" temperature suffix designates the -40C to +105C automotive grade and the "T" suffix denotes tape-and-reel packaging, while the -80 suffix indicates 80 MHz maximum CPU clock. This page synthesizes distributor pricing, pin-compatible drop-in alternatives, and practical design notes not found in the manufacturer datasheet.

USD $5.88 재고 있음

PIC32MX575F512L-80I/BG

PIC32MX575F512L-80I/BG - 80MHz 32-bit MCU, 512KB Flash, USB/CAN | Microchip

The Microchip Technology PIC32MX575F512L-80I/BG is a high-performance 32-bit MIPS M4K microcontroller operating at 80 MHz (105 DMIPS) with 512 KB of Flash and 64 KB of SRAM, packaged in a 121-pin TFBGA (10x10 mm). It integrates a USB 2.0 On-The-Go peripheral (with integrated PHY), a CAN 2.0b module, 4 dedicated DMA channels for USB, a 5-stage Harvard pipeline, and MIPS16e code compression for up to 40% smaller code footprint. The device runs from a 2.5 V to 3.6 V supply with 53 general-purpose I/O pins, supporting up to 5 V tolerance on most digital inputs. What is a PIC32MX microcontroller? PIC32MX is Microchip's MIPS32 M4K-core 32-bit MCU family that bridges 8-bit PIC and 32-bit ARM-class performance for USB, CAN, and Ethernet connectivity. Within the power management IC hierarchy it sits as a general-purpose microcontroller -> 32-bit MCU -> MCU. The M4K core delivers 1.53 DMIPS/MHz with hardware multiply/divide and a single-cycle shadow register set for fast interrupt response. Key features include 512 KB Flash, 64 KB RAM, 80 MHz / 105 DMIPS performance, integrated USB-OTG PHY, CAN 2.0b, 10-bit 1 Msps ADC up to 16 channels, and rich serial peripherals (UART, SPI, I2S, I2C). The chip also supports PMP/PSP parallel interfaces for external graphics or memory. AES and Cryptographic accelerators are absent on this specific MPN (those appear on PIC32MX5XX/6XX/7XX higher-tier variants). The 121-pin TFBGA package suits high-density designs needing >53 I/O lines. Technical depth: 5-stage pipeline + Harvard architecture + 16-bit MIPS16e instructions = high code density at 32-bit throughput. Dedicated DMA offloads USB and CAN traffic from the CPU, leaving the M4K core free for application code and signal processing. Typical applications include industrial USB peripherals (HID, CDC, mass storage), CAN-based automotive body controllers, Ethernet-enabled embedded web servers (using external MAC+PHY), medical instrument data loggers, and multi-motor industrial automation. The wide peripheral mix reduces BOM cost versus discrete MCU + USB transceiver designs. Design consideration: place four decoupling capacitors (100 nF + 1 uF) within 5 mm of each power pin pair, keep the 12 MHz crystal traces short, and route the USB DP/DM differential pair with 90 ohm differential impedance. Ensure the TFBGA's center pad is soldered to a 5 x 5 mm ground plane for thermal relief. This page synthesizes distributor pricing, drop-in alternatives, and practical design notes not found on standalone Microchip product pages or datasheet PDFs.

USD $5.88 재고 있음

PIC32MX575F512L-80I/PT

PIC32MX575F512L-80I/PT - 80MHz MIPS MCU 512KB USB/CAN MCU | Microchip

The Microchip Technology PIC32MX575F512L-80I/PT is a 32-bit MIPS M4K microcontroller running at 80 MHz (105 DMIPS), integrating 512 KB of Flash program memory and 64 KB of SRAM, and packaged in a 100-pin TQFP (PT) industrial-temperature-grade (-40C to +85C) footprint. It includes a USB 2.0 On-The-Go peripheral with integrated PHY, a CAN 2.0b controller with 1024 message buffers, a 10/100 Ethernet MAC (MII/RMII), and a 16-channel 10-bit ADC at 1 Msps. A 32-bit microcontroller (MCU) is a single-chip computer based on a 32-bit datapath that can address more than 4 GB of memory, executes instructions out of Flash, and integrates peripherals such as timers, ADC/DAC, communication controllers, and GPIO. The PIC32MX family belongs to the broader category of microcontrollers -> embedded microprocessors -> semiconductors, and combines a Harvard architecture, 5-stage pipeline, and MIPS16e code compression to deliver high DMIPS/mm2 density for connected embedded designs. Key features of this variant include dedicated DMA channels for USB, a parallel master port (PMP) for graphics or parallel memory, five 16-bit timers/counters, two I2C, two SPI, and a JTAG debugger (non-IP-C) interface. The 80 MHz core delivers 105 DMIPS throughput, while the 64 KB SRAM with 3 KB of auxiliary flash supports data logging and bootloader scenarios. The USB OTG peripheral supports Host, Device, and On-The-Go roles with an integrated PHY that eliminates external transceiver components, simplifying BOMs for connected products. The architecture pairs a MIPS M4K RISC core with single-cycle multiply, divide, and bit-field instructions, a 5-stage pipeline, and a Harvard bus that allows simultaneous instruction fetch and data access. Up to 41 DMIPS can be sustained per MHz under MIPS16e compression, with 1.56 DMIPS/MHz typical. The 4-channel DMA controller offloads data movement between peripherals and RAM, freeing the CPU for application logic. The 2.3 V to 3.6 V operating range and on-chip brown-out reset plus watchdog timer improve robustness in industrial environments. Typical applications include industrial automation, USB peripherals (HID/CDC/MSC and CDC+Ethernet bridging), CAN-bus nodes (automotive and industrial control), Ethernet-connected embedded web servers, point-of-sale terminals, and graphical HMI panels with resistive-touch sensing. The combination of USB OTG, CAN, and Ethernet in a single die is rare at this price point, simplifying BOMs in multi-bus gateways. When designing with the PIC32MX575F512L-80I/PT, ensure that each VDD/AVDD pair has a 0.1 uF + 10 uF local decoupling network within 3 mm of the pin, and that the 8 MHz primary oscillator is paired with the required 1 ms startup delay. The USB pins D+/D- require a 90 ohm differential trace and 47 K pull-down on the ID pin for OTG operation; the CAN bus should include a TJA1050 or MCP2551 external transceiver since this die only exposes the protocol controller. This page synthesizes DigiKey and Mouser pricing, Microchip PIC32MX5XX/6XX/7XX family datasheet specifications, drop-in alternative cross-references, and practical design notes not bundled in the manufacturer datasheet.

USD $6.12 재고 있음

하위 카테고리

제품 (32725)

PIC32MX570F512LT-I/GJX - 50MHz 32-bit MCU 512KB Flash TFBGA-100

PIC32MX570F512LT-V/GJX - 50MHz 32-bit MCU, 512KB Flash, TFBGA-100 | Microchip

PIC32MX570F512LT-V/PT - 32-bit MCU, 512KB Flash, USB/CAN, 100-TQFP

PIC32MX575F256H-80I/MR - 32-bit MCU 256KB Flash 80MHz 64-VQFN | Microchip

PIC32MX575F256H-80I/PT - 80MHz 32-bit MCU 256KB Flash | Microchip

PIC32MX575F256HT-80I/PT - 80MHz 32-bit MCU 256KB Flash USB/CAN | Microchip

PIC32MX575F256HT-80V/MR - 80MHz 32-bit MCU 256KB Flash | Microchip

PIC32MX575F256L-80I/BG - 80MHz 256KB Flash MCU | Microchip

PIC32MX575F256L-80V/BG - 80MHz 32-bit MCU 256KB Flash | Microchip

PIC32MX575F256L-80V/PF - 80MHz 32-bit MCU 256KB Flash | Microchip

PIC32MX575F256LT-80I/BG - 80MHz 32-bit MCU 256KB Flash TFBGA-121

PIC32MX575F256LT-80I/PF - 80MHz 32-bit MCU 256KB Flash USB/CAN | Microchip

PIC32MX575F256LT-80I/PT - 32-bit 80MHz MCU 256KB Flash USB CAN | Microchip

PIC32MX575F256LT-80V/BG - 256KB Flash 32-bit MCU | Microchip

PIC32MX575F256LT-80V/PF - 32-bit 80MHz MCU, 256KB Flash, USB-OTG, CAN | Microchip

PIC32MX575F256LT-80V/PT - 80MHz 256KB Flash 32-bit MCU | Microchip

PIC32MX575F512H-80I/MR - 32-bit 80MHz 512KB Flash MCU | Microchip

PIC32MX575F512H-80I/PT - 80MHz MCU 512KB Flash USB/CAN | Microchip

PIC32MX575F512H-80V/PT - 32-bit MCU 512KB Flash 64TQFP | Microchip

PIC32MX575F512HT-80I/PT - 80MHz MIPS32 M4K MCU 512KB Flash | Microchip

PIC32MX575F512HT-80V/MR - 80MHz 512KB Flash 32-bit MCU | Microchip

PIC32MX575F512HT-80V/PT - 80MHz 512KB Flash MCU | Microchip

PIC32MX575F512L-80I/BG - 80MHz 32-bit MCU, 512KB Flash, USB/CAN | Microchip

PIC32MX575F512L-80I/PT - 80MHz MIPS MCU 512KB USB/CAN MCU | Microchip