집적 회로

하위 카테고리

📁 ADC/DAC 3,100+ 제품 📁 증폭기 IC 1,900+ 제품 📁 오디오 코덱 18 제품 📁 오디오 IC 2 제품 📁 클록 및 타이밍 660+ 제품 📁 Comparator ICs 1 제품 📁 DSP 1,100+ 제품 📁 데이터 수집 IC 2 제품 📁 디지털 포텐셔미터 4 제품 📁 디스플레이 드라이버 및 컨트롤러 1 제품 📁 FPGA & CPLD 7,300+ 제품 📁 인터페이스 IC 3,300+ 제품 📁 LED 드라이버 1 제품 📁 로직 IC 460+ 제품 📁 메모리 IC 870+ 제품 📁 마이크로컨트롤러 20,000+ 제품 📁 마이크로프로세서 4 제품 📁 모터 드라이버 1 제품 📁 기타 1 제품 📁 Sensor and Detector Interfaces 1 제품 📁 특수 IC 15 제품 📁 비디오 IC 14 제품

제품 (39,000+)

P1014NSE5HFA557 - QorIQ P1 800MHz e500v2 MPU | NXP
P1014NSE5HFA557

P1014NSE5HFA557 - QorIQ P1 800MHz e500v2 MPU | NXP

The NXP (formerly Freescale) P1014NSE5HFA557 is a QorIQ P1 series communications microprocessor featuring a single 32-bit Power Architecture e500v2 core running up to 800 MHz, integrated in a 425-terminal TE-PBGA (425-TEPBGA1) package with 0.80 mm ball pitch. The P1014 family targets cost-sensitive, power-efficient embedded networking and industrial control applications where deterministic processing, low thermal dissipation, and a compact BGA footprint are required. A QorIQ communications processor is a 32-bit Power Architecture system-on-chip (SoC) that integrates one or more e500 cores with networking peripherals, DDR memory controllers, and high-speed serial interfaces. The P1014 belongs to the broader Power Architecture (PowerPC) communications processor family, sitting below the multi-core P2/P3/QorIQ lines and above the simpler PowerQUICC II devices. Compared to general-purpose microcontrollers, a QorIQ part delivers integrated Ethernet MACs, security acceleration, and large DDR2/DDR3 support, enabling it to replace external components in router, gateway, and factory-floor designs. Key features of the P1014 include a single e500v2 core with 32 KB instruction and 32 KB data L1 caches, a 256 KB unified L2 cache with ECC, dual 10/100/1000 Mbps Ethernet MACs, DDR2/DDR3 memory controller with ECC, PCI Express and SATA interfaces, USB 2.0, and integrated security engines for IPSec, SSL/TLS, and bulk data encryption. The 557 designator encodes the specific speed grade (800 MHz core / 667 MHz platform) and operating temperature range per NXP's product naming convention. Typical applications include industrial Ethernet gateways, substation routers and protocol converters, small-form-factor NAS/SAN appliances, factory-floor controllers with deterministic networking, and secure VPN concentrators. The combination of low power consumption, integrated peripherals, and Power Architecture software compatibility makes the P1014 attractive for long-lifecycle embedded designs. When designing with the P1014NSE5HFA557, ensure the PCB land pattern follows NXP's 425-TEPBGA1 footprint (0.80 mm pitch). Use at least 4-layer PCB construction with continuous ground planes for signal integrity on DDR traces, and provide adequate thermal vias beneath the BGA die for heat extraction. Software support is available through NXP's CodeWarrior, Linux BSP, and VxWorks distributions.

견적 요청 문의하기
P1014NSE5HHA - QorIQ P1014 SoC, 800 MHz e500, 425-TEPBGA | NXP
P1014NSE5HHA

P1014NSE5HHA - QorIQ P1014 SoC, 800 MHz e500, 425-TEPBGA | NXP

The NXP (formerly Freescale) P1014NSE5HHA is a QorIQ P1014 communications processor built on the Power Architecture e500v2 core, delivering up to 800 MHz operation in a 425-ball TEPBGA (19x19 mm) package. It integrates a single 32-bit Power Architecture core with on-chip SEC security engine, dual GbE controllers, three PCIe controllers, two SATA ports, two USB 2.0 ports (host + device), and a 16-bit DDR3 memory controller, providing a complete system-on-chip (SoC) for cost- and power-sensitive networking. A QorIQ communications processor is a category of Power Architecture-based SoCs designed by NXP/Freescale to consolidate networking, security, and I/O functions that previously required separate components. Within the broader taxonomy, the P1014 sits in the entry tier of the QorIQ P1 family, between the lower-frequency P1010 and the higher-end P1020 dual-core parts, and is built on a 45 nm CMOS process for low static and dynamic power. Key features include 800 MHz core frequency, integrated SEC 4.0 cryptographic accelerator, hardware pattern-matching and queuing engines, dual 10/100/1000 Ethernet MACs with SGMII support, three PCI Express Gen 1 controllers, two SATA Gen 2 interfaces, USB 2.0 host and device, 16-bit DDR3 with ECC up to 800 MT/s, and an operating temperature range of 0°C to 105°C suitable for thermally managed industrial enclosures. The integrated SEC engine offloads IPSec, SSL/TLS, and bulk encryption from the core, while the queue manager and pattern-matching blocks accelerate deep-packet inspection workloads without external TCAMs. The P1014NSE5HHA is intended for industrial-grade networking equipment where the SoC must combine cryptographic acceleration, multiple high-speed I/Os, and DDR3 memory in a single 425-ball 19x19 mm BGA footprint. Typical applications include small-form-factor industrial routers, secure edge gateways, industrial IoT gateways, networked storage controllers (NAS/SAN), factory automation controllers, and compact wireless backhaul equipment. When designing with this device, allocate the DDR3 fly-by routing carefully to maintain signal integrity at 800 MT/s, place at least one 100 nF decoupling capacitor per power pin pair adjacent to the BGA, and verify thermal headroom with the manufacturer-provided junction-to-ambient and junction-to-case thermal resistance values for the 425-TEPBGA package. Use NXP's CodeWarrior or QorIQ Linux SDK for software development, and consult the reference design guide for the SERDES reference clocking and PCIe reference clock distribution topology.

견적 요청 문의하기
P1014NSN5DFA - QorIQ P1014 e500v2 SoC 800MHz | NXP Semiconductors
P1014NSN5DFA

P1014NSN5DFA - QorIQ P1014 e500v2 SoC 800MHz | NXP Semiconductors

The NXP Semiconductors (formerly Freescale) P1014NSN5DFA is a QorIQ P1014 communications processor built on the Power Architecture e500v2 core, integrating GbE, USB, SATA, and PCIe connectivity into a single 425-ball TEPBGA I (19x19 mm) package. It runs up to 800 MHz and is qualified for industrial operating conditions from 0C to 105C. A communications processor is a system-on-chip (SoC) that combines a CPU core, memory controller, and multiple high-speed IO peripherals on a single die; it is the next-generation evolution of the PowerQUICC series and is part of NXP's QorIQ P1 family. Within the system hierarchy, the P1014 sits between general-purpose microcontrollers and high-end networking SoCs, targeting cost- and power-sensitive applications such as SOHO routers and industrial gateways. The same family tree also includes the lower-speed P1010 variant (up to 533 MHz), letting designers scale performance within a pin-compatible footprint. Key features include a 32-bit Power Architecture e500v2 core with dual-issue superscalar execution, a 32/16-bit DDR3 memory controller with ECC support, two Gigabit Ethernet MACs (one RGMII, one SGMII capable), two USB 2.0 controllers (host + device/host), two SATA 2.0 ports at 3 Gb/s, and one PCIe x4 Gen 2 controller. Integrated security includes basic secure-boot and Trust Architecture support typical of the P1 family. The device integrates the SerDes, networking, and IO IP that historically required companion chipsets in PowerQUICC designs, reducing PCB area, BOM count, and design complexity. Power is supplied through multiple rails including 1.0V core and 1.5V/1.8V DDR, with power management controlled by on-chip PLLs. Typical applications include SOHO/SMB routers, wireless LAN access points, industrial automation controllers, networked printers, IP cameras/NVR, and smart-grid gateway nodes. The industrial-grade temperature range and integrated networking make it especially well suited to harsh-environment edge appliances. When designing with this part, ensure the DDR3 routing meets the controller's impedance and length-matching rules and that the SerDes reference clock is clean, because signal-integrity violations here degrade GbE and PCIe link margin. The 425-ball TEPBGA requires standard 0.8 mm-pitch PCB rules plus microvia or laser-drill capability. This page synthesizes distributor pricing, drop-in alternatives drawn from the same P1 family, and practical design notes that complement rather than duplicate the manufacturer datasheet.

견적 요청 문의하기
P1014NSN5DFA557 - QorIQ P1 800MHz PowerPC e500v2 MPU | NXP
P1014NSN5DFA557

P1014NSN5DFA557 - QorIQ P1 800MHz PowerPC e500v2 MPU | NXP

The NXP P1014NSN5DFA557 is a PowerPC e500v2 microprocessor in NXP's QorIQ P1 family with a single 32-bit core running at 800 MHz, housed in a 425-ball TEPBGA package (19 x 19 mm). It integrates 256 KB of L2 cache with ECC, 32 KB of instruction and 32 KB of data L1 cache per core, and 64-bit DDR3 memory controller with ECC support, making it well suited for low-power, deterministic networking and control plane workloads. What is a QorIQ communications processor? QorIQ is a NXP semiconductor family that sits in the broader taxonomy of microprocessors (MPU) and embedded processors, which are higher-performance than microcontrollers (MCU) and are typically deployed as the central compute node in routers, switches, and access gateways. The P1 series is the lower-power tier of QorIQ, sharing software compatibility with the higher-end P2/P3/P4 families via the standard PowerPC e500v2 instruction set, Book-E programming model, and common peripherals. The P1014 specifically targets fanless and thermally constrained designs that still require multi-gigabit packet processing. The P1014NSN5DFA557 supports a single 533/667/800 MHz core speed bin, dual 10/100/1000 Mbps Ethernet controllers (eTSEC), PCIe Gen1/Gen2, and up to 32-bit DDR3 with ECC at up to 800 MHz. A hardware encryption block accelerates AES, DES, 3DES, SHA-1/256, and public-key algorithms, with secure boot supported through the on-chip secure boot extension. Interface flexibility is provided through USB 2.0, SD/MMC, two I2C controllers, and four UARTs. Low-power standby modes reduce idle consumption to a fraction of the active budget. Typical applications include SOHO/SMB routers, wireless LAN access points, smart grid gateways, factory-floor protocol bridges, and industrial IoT edge nodes. NXP also positions P1014 derivatives for networked printers, IP cameras, and HVAC controllers where deterministic real-time response is required. When designing with the P1014, plan 4-layer PCB stack-up with controlled-impedance routing for DDR3; allocate 1.0 V core (min 0.95 V, max 1.05 V) and 1.5 V DDR3 supplies with bulk decoupling within 50 mm of the BGA. Total power at 800 MHz typically stays below 3.5 W, allowing passive heatsinking. This page consolidates cross-brand positioning context, drop-in same-family replacement guidance, and design notes not found in the standalone datasheet PDF.

견적 요청 문의하기
P1014NSN5HFA - QorIQ P1014 800MHz SoC, DDR3, GbE | NXP
P1014NSN5HFA

P1014NSN5HFA - QorIQ P1014 800MHz SoC, DDR3, GbE | NXP

The NXP P1014NSN5HFA is a QorIQ P1 communications processor SoC featuring a single 32-bit Power Architecture e500v2 core running at 800 MHz, integrating USB 2.0, SATA, Gigabit Ethernet, PCIe, and DDR3 memory controller in a 425-ball TEPBGA I (19x19 mm) package. It is positioned as the higher-speed, higher-cache sibling of the P1010 family, expanding QorIQ performance into cost- and power-sensitive networking applications such as industrial control, factory automation, and entry-level network appliances. What is a QorIQ communications processor? QorIQ is NXP's Power Architecture-based system-on-chip (SoC) platform for networking and industrial embedded applications, sitting in the hierarchy of: SoC -> communications processor -> microprocessor (MPU). It integrates CPU cores with networking peripherals (Ethernet, PCIe, SATA, USB), a memory controller, and security engines on a single die, replacing multi-chip designs with one part. QorIQ P1 series targets low-power, single-core applications where cost and deterministic performance matter more than multi-core throughput. Key features of the P1014NSN5HFA include a single Power Architecture e500v2 core at 800 MHz, integrated DDR3 memory controller with ECC support, three Gigabit Ethernet interfaces (one with packet parsing acceleration), two PCIe Gen1 controllers, two SATA 2.0 ports, USB 2.0 host/device, and a security engine for IPsec, SSL/TLS, and trusted boot. The device supports an operating temperature range of 0C to 105C, enabling deployment in thermally demanding industrial enclosures without additional cooling. The P1014 architecture implements a 32-bit superscalar e500v2 core with hardware virtualization and signal-processing extensions. Its on-die packet processing engine accelerates routing and filtering tasks, offloading work from the core and reducing latency for time-sensitive network traffic. The integrated security engine handles AES, 3DES, and SHA acceleration, enabling VPN termination and secure boot without external crypto chips. Typical applications for the P1014NSN5HFA include industrial Ethernet gateways, factory automation controllers, smart grid substation equipment, entry-level routers and switches, network-attached storage controllers, and embedded control boards in railway and energy systems. Its combination of networking peripherals and a deterministic real-time capable core makes it especially suitable for protocol conversion gateways that bridge Modbus, EtherCAT, or PROFINET with enterprise networks. When designing with this device, allocate at least 8 PCB layers with dedicated ground and power planes, and follow NXP AN4160 layout guidance for the DDR3 controller. The device supports a wide range of boot sources including NOR flash, NAND flash, SPI, and SD/MMC, simplifying firmware development. JTAG and Aurora debug interfaces are available for boundary-scan and trace-based debugging. This page synthesizes distributor pricing, drop-in alternatives within the QorIQ P1 family, and practical design notes not found in the manufacturer datasheet.

견적 요청 문의하기
P1014NSN5HFA557 - QorIQ 32-bit Power Arch SoC 800MHz | NXP
P1014NSN5HFA557

P1014NSN5HFA557 - QorIQ 32-bit Power Arch SoC 800MHz | NXP

The NXP P1014NSN5HFA557 is a QorIQ 32-bit Power Architecture system-on-chip (SoC) communications processor operating at up to 800 MHz core frequency with a 667 MHz DDR3 memory controller, housed in a 425-ball, 0.8 mm pitch PBGA package measuring 19 x 19 mm. Built on 45 nm low-power CMOS technology, the P1014 integrates a single e500 core with 32 KB I-cache and 32 KB D-cache, hardware ECC-protected DDR3/3L memory controller, dual GbE controllers, three PCIe Gen 1.1 controllers, two SATA 2.0 ports, USB 2.0 (host/device/OTG), and integrated security engine with trusted boot and secure debug. A QorIQ communications processor is a multicore Power Architecture SoC designed for cost- and power-sensitive networking, industrial control, and secure gateway applications. Within the broader NXP product hierarchy, the P1010/P1014 family sits below the high-end P2020/P2040 dual-core devices and above the value-tier P1010/P1013 single-core parts, occupying the integrated-networking sub-segment of the Power Architecture communications processor roadmap. Key differentiating features of the P1014 include hardware-accelerated protocol handling for packet processing, integrated SERDES lanes that eliminate external PHYs for GbE/SATA/PCIe, and a flexible SerDes configuration supporting up to 5 lanes. The device operates from a single 1.0 V nominal core supply (range 0.95 V to 1.05 V) with separate I/O and PLL rails, supporting commercial 0 C to +105 C junction temperature. Typical applications include industrial IoT gateways, factory automation controllers, secure network appliances, fanless embedded routers, and smart-grid infrastructure. The integrated security engine and Trust Architecture support tamper-resistant firmware boot, while the low 4 W typical power envelope enables fanless designs in compact enclosures. When designing with the P1014, allocate adequate decoupling on every 1.0 V rail and provide a 25 MHz reference clock into the differential SYSCLK pins. Route all high-speed SERDES lanes with controlled-impedance 85 ohm differential pairs and follow the NXP reference board stack-up to maintain signal-integrity margins. This page synthesizes octopart distributor pricing, octopart cross-reference listings, and practical design notes for the P1014NSN5HFA557, complementing the manufacturer datasheet with engineering insight not found on stock pages.

견적 요청 문의하기
P1014NSN5HFB557 - QorIQ P1 32-Bit Power Arch SoC, 800MHz | NXP
P1014NSN5HFB557

P1014NSN5HFB557 - QorIQ P1 32-Bit Power Arch SoC, 800MHz | NXP

The NXP P1014NSN5HFB557 is a 32-bit Power Architecture system-on-chip (SoC) microprocessor from the QorIQ P1 family, integrating a single e500v2 core running at up to 800 MHz in a 425-TEPBGA package. It is specifically designed for cost-sensitive networking and embedded applications such as wireless LAN access points, SOHO/SMB routers, and industrial control. The QorIQ platform is a series of Power Architecture-based SoCs from NXP (formerly Freescale) targeting networking infrastructure and embedded systems. The P1 series sits at the entry-level tier of the QorIQ lineup, balancing modest performance with low power draw and rich peripheral integration. Understanding this taxonomy helps position the P1014 within the broader semiconductor hierarchy: Power Architecture SoC -> embedded microprocessor -> SoC -> semiconductor device. Key features include an integrated PowerPC e500v2 core with 32 KB L1 instruction and 32 KB L1 data caches, hardware-based encryption acceleration (SEC), DDR3 memory controller with ECC support, and a flexible peripheral set covering USB 2.0, SATA 2.0, dual Gigabit Ethernet with packet acceleration, and PCI Express Gen 2.0. The 425-TEPBGA package exposes all high-speed serial and parallel interfaces for full SoC utilization in fanless networking gear. Architecturally, the P1014 leverages Freescale/NXP's proven Power Architecture e500v2 with dual-issue superscalar in-order execution. The on-chip SEC engine accelerates DES, 3DES, AES, and SHA-1/256 algorithms offloading IPsec and TLS tasks from the CPU, while packet acceleration engines handle header parsing and checksum computation. The integrated DDR3 controller with ECC supports up to 4 GB of addressable memory for routing tables and bulk data buffers. Typical applications include wireless LAN access points, SOHO/SMB routers and gateways, networked industrial controllers, networked printing and imaging devices, and entry-level unified threat management appliances. The 0 to 105 °C junction temperature range makes the P1014 suitable for sealed enclosures without forced-air cooling in office and light-industrial environments. When designing with the P1014, ensure the PCB is laid out as a 12-layer (or more) stack-up to maintain DDR3 signal integrity, and provide a 25 MHz reference clock with low-jitter characteristics. Power sequencing of the core, SerDes, and I/O rails must follow the reference manual sequence to avoid latch-up during startup. This page synthesizes distributor availability, package and pinout details, drop-in compatible variants in the P1014 family, and practical design guidance distilled from NXP's reference documentation and the active distributor ecosystem.

견적 요청 문의하기
P1014NSN5HHB - QorIQ 32-Bit 800MHz PowerPC SoC | NXP
P1014NSN5HHB

P1014NSN5HHB - QorIQ 32-Bit 800MHz PowerPC SoC | NXP

The NXP P1014NSN5HHB is a QorIQ P1014 communications processor from NXP's value-performance tier, integrating a 32-bit PowerPC e500v2 core running at 800 MHz in a 425-ball TEPBGA (19x19 mm) package. The device is manufactured on a 45 nm low-power CMOS process and operates over a 0 to 105 C junction temperature range, targeting cost-sensitive networking, network-attached storage, digital video surveillance, and industrial control applications. Background: A QorIQ communications processor is a system-on-chip (SoC) that combines one or more CPU cores with integrated networking peripherals, memory controllers, and acceleration engines on a single die. The QorIQ family sits within NXP's broader portfolio of Power Architecture (PowerPC) embedded processors, occupying a tier between low-power microcontrollers and high-end multicore communications SoCs. Key features include a 32-bit e500v2 core with integrated L1/L2 caches, hardware cryptography acceleration, dual GbE controllers, three PCIe Gen2 controllers, USB 2.0, SATA 2.0, and a 32/64-bit DDR3 memory controller with ECC support. The SoC provides up to 800 MHz core frequency while maintaining low power consumption suitable for fanless industrial designs. Architecturally, the P1014NSN5HHB combines a PowerPC scalar core with tightly-coupled accelerators for packet processing and security offload. The 45 nm process node and integrated voltage regulation minimize external component count, reducing BOM cost and PCB footprint for embedded networking designs. Typical applications include industrial Ethernet routers, network-attached storage appliances, IP video surveillance recorders, factory automation controllers, and small-to-medium business firewall/UTM platforms. The integrated GbE and PCIe make the device particularly suited for line-rate packet processing without an external switch. Design consideration: When using P1014NSN5HHB, ensure proper thermal management on the TEPBGA package with adequate PCB copper area under the heat-spreader. DDR3 trace length matching, signal integrity on SerDes lanes, and decoupling capacitor placement per NXP hardware design guidelines are essential for stable operation. This page synthesizes distributor pricing, drop-in alternatives, and practical design notes not consolidated in the manufacturer datasheet, providing actionable selection guidance for embedded engineers.

견적 요청 문의하기
P1014NXE5HFA557 - QorIQ P1 800MHz PowerPC MPU | NXP | BGA-425
P1014NXE5HFA557

P1014NXE5HFA557 - QorIQ P1 800MHz PowerPC MPU | NXP | BGA-425

The NXP Semiconductors (formerly Freescale) P1014NXE5HFA557 is a QorIQ P1 series 32-bit PowerPC e500v2 microprocessor IC integrating a single core running up to 800 MHz, housed in a 425-ball TEPBGA package measuring 19 mm x 19 mm with a 0.80 mm ball pitch. The device is built on a CMOS process with an integrated L1/L2 cache hierarchy and serves as the communications-processing heart of mid-range networking and industrial control designs. A microprocessor (MPU) is a single-chip CPU that integrates the arithmetic logic unit, control unit, register file, on-chip cache, and memory management unit into one package, providing the instruction-execution engine for embedded systems. Within the broader taxonomy, MPU -> microprocessor -> processor -> semiconductor device, the QorIQ P1 family sits in the networking-optimized branch of NXP's Power Architecture portfolio, sitting between the PowerQUICC III communications processors and the higher-end QorIQ P2/P3 tiers. Key features of the P1014NXE5HFA557 include the Power Architecture e500v2 core with dual-issue integer pipeline, hardware MMU and 36-bit physical addressing, integrated security engine supporting AES, DES, 3DES, and SHA accelerators, dual 10/100/1000 Ethernet MACs, four SERDES lanes supporting multiple serial protocols, and a flexible DMA subsystem. The device also integrates DDR2/DDR3 memory controllers with ECC, a 32-bit PCI Express interface, USB 2.0, SDHC, and I2C/SPI/UART peripherals. The P1014's e500v2 core implements Book-E Power Architecture with virtualization support, signal-processing extensions (SPe), and an integrated double-precision FPU option. The on-chip L2 cache is configurable from 256 KB to 512 KB and supports ECC, while the fabric connects cores, peripherals, memory controller, and SERDES blocks via a coherent 64-bit Coherent Bus. Typical applications include wired/wireless routing, line cards, industrial gateways, factory automation controllers, network-attached storage (NAS), and secure VPN appliances. Industrial temperature variants like this part (suffix NxE) are specified for -40C to +105C operation. When designing with this device, ensure the PCB accommodates a 19x19mm BGA land pattern with 6-8 layer stack-up for SERDES signal integrity, and follow NXP's hardware design guide for power-rail decoupling: solid 0.95V to 1.05V nominal supply with bulk ceramic and polymer tantalum hold-up capacitance. This page synthesizes distributor pricing, drop-in alternatives, application context and practical design notes not found in the standalone manufacturer datasheet, helping procurement and embedded-architect teams evaluate the QorIQ P1014 for new designs and existing platforms.

견적 요청 문의하기
P1014NXE5HHA - 800MHz e500v2 QorIQ SoC, 425-TEPBGA | NXP
P1014NXE5HHA

P1014NXE5HHA - 800MHz e500v2 QorIQ SoC, 425-TEPBGA | NXP

The NXP P1014NXE5HHA is a QorIQ P1014 communications processor built around a single 32-bit Power Architecture e500v2 core running at 800 MHz, integrated into a 425-pin TEPBGA I (19x19) package. This system-on-chip (SoC) combines CPU, memory controller, and high-speed serial interfaces on a single 45 nm die, targeting cost- and power-sensitive networking and industrial applications. A QorIQ communications processor is a Power Architecture-based SoC that integrates one or more CPU cores with packet-processing accelerators, security engines, and a rich set of high-speed I/O such as SATA, USB, PCIe, GbE, and DDR3 memory controllers. QorIQ belongs to the broader Power Architecture microprocessor family and is positioned as the successor to Freescale's PowerQUICC III platform for embedded communications. It serves as the central processing node in routers, switches, industrial gateways, and single-board computers where deterministic packet handling and integrated peripherals reduce system BOM. Key features include 800 MHz core frequency, 32 KB L1 instruction cache and 32 KB L1 data cache per core, integrated DDR3 memory controller with ECC support, dual GbE, dual SATA, USB 2.0, dual PCIe, SEC security engine, and an extended-temperature operating range of -40C to +105C. The -HHA suffix denotes the industrial / extended temperature grade (vs. -FFB commercial) and an internal die revision, all delivered in a 19x19 mm TEPBGA I package. The P1014NXE5HHA's Power Architecture e500v2 core uses a 7-stage pipeline with hardware-assisted double-precision floating point, Book-E embedded architecture extensions, and a coherent memory bus for symmetrical multiprocessing expansion. The integrated SEC crypto engine accelerates DES, 3DES, AES, ARC4, MD5, SHA-1/256, and public-key algorithms, offloading encryption from the CPU. Typical applications include industrial Ethernet switches, smart-grid gateways, factory-floor protocol converters, edge routers, NAS controllers, and single-board computers for embedded Linux distributions. The integrated peripherals (SATA, USB, PCIe, DDR3) eliminate most companion chips required by MCU-class designs. When designing with this device, ensure the 19x19 mm TEPBGA I land pattern uses 0.8 mm pitch with proper thermal vias under the exposed die flag to keep junction temperature within the -40C to +105C envelope. Boot configuration resistors must be set to the correct source (NOR/NAND/SD/SPI) before reset is released. This page synthesizes distributor pricing, drop-in alternatives, and practical design notes not found on the manufacturer datasheet cover page, making it easier for procurement and engineering teams to evaluate the P1014NXE5HHA against the wider QorIQ P1 family.

견적 요청 문의하기
P1014NXN5DFA - QorIQ P1014 32-Bit SoC 533MHz 425-TEPBGA | NXP
P1014NXN5DFA

P1014NXN5DFA - QorIQ P1014 32-Bit SoC 533MHz 425-TEPBGA | NXP

The NXP P1014NXN5DFA is a QorIQ P1 communications processor featuring a 32-bit Power Architecture e500v2 core running up to 533 MHz (per datasheet, with P1014 family variants up to 800 MHz), integrated SEC crypto acceleration, USB, SATA, GbE, PCIe and DDR3 memory controller, housed in a 425-ball TEPBGA package measuring 19x19 mm. It extends the QorIQ family into cost- and power-sensitive industrial and networking applications where integrated peripherals reduce external component count. A communications processor is a specialized system-on-chip (SoC) that integrates one or more CPU cores with networking peripherals, security engines and memory controllers on a single die. In the wider semiconductor taxonomy it sits below general-purpose microprocessors and above simple microcontrollers, optimized for protocol processing, packet inspection and secure networking. The QorIQ family is NXP's line of Power Architecture-based SoCs targeting routers, switches, industrial gateways and embedded networking equipment. Key features include the e500v2 single-issue core with integrated SEC 4.x crypto block supporting DES, 3DES, AES, SHA and RSA, dual 10/100/1000 Ethernet MACs with IEEE 1588 timestamping, two USB 2.0 controllers (host + device/OTG), two SATA 2.0 interfaces, three PCIe Gen2 controllers and a 32-bit DDR3/DDR3L SDRAM controller with ECC support. The -40 C to +105 C temperature range qualifies the part for industrial and extended-temperature networking deployments. Typical applications include industrial Ethernet routers, secure IoT gateways, factory automation controllers, smart-grid concentrators, substation communication equipment and embedded networking modules. The integrated peripherals remove the need for discrete Ethernet PHYs, SATA controllers and crypto ASICs, reducing board area and BOM cost in space-constrained designs. Design considerations focus on power sequencing of the multiple supply rails (core, I/O, DDR PHY, Ethernet PHYs), thermal dissipation via the package's exposed die region, JTAG boundary-scan test access, and careful PCB layout to maintain DDR3 signal integrity at 533 MHz. The SEC engine offloads cryptographic workloads from the main core, freeing CPU cycles for application logic and protocol stacks.

견적 요청 문의하기
P1014NXN5DFA557 - QorIQ P1 PowerPC e500v2 MPU 533MHz TEPBGA-425 | NXP
P1014NXN5DFA557

P1014NXN5DFA557 - QorIQ P1 PowerPC e500v2 MPU 533MHz TEPBGA-425 | NXP

The NXP P1014NXN5DFA557 is a single-core QorIQ P1 communications microprocessor based on the PowerPC e500v2 core architecture, operating at 533 MHz, housed in a 425-ball TEPBGA I (19x19 mm) package. It belongs to the broader QorIQ P1 family of integrated communications processors targeting cost-sensitive networking, industrial control, and embedded computing applications. A QorIQ communications processor is a system-on-chip (SoC) that integrates one or more CPU cores with networking-specific accelerators, memory controllers, security engines, and high-speed serial interfaces. Within the NXP ecosystem, the P1 series sits below the higher-tier P2/P3 multi-core parts but above the entry-level QorIQ devices. The P1014 specifically targets applications requiring deterministic single-thread performance with low power consumption. Key features include a 32-bit PowerPC e500v2 core with integrated L1/L2 cache hierarchy, a DDR2/DDR3 memory controller, multiple Gigabit Ethernet interfaces, PCI Express support, USB 2.0, SD/MMC, and integrated security acceleration engines. The 425-ball TEPBGA package provides the I/O density required for high-bandwidth networking applications while maintaining a compact 19x19 mm footprint suitable for space-constrained embedded designs. The P1014 is built on a CMOS process optimized for low power dissipation in thermally constrained networking environments. Its integrated architecture reduces the need for external peripherals, lowering overall BOM cost and simplifying PCB layout in applications like industrial Ethernet switches, edge routers, and serial-to-IP protocol converters. Typical applications include industrial Ethernet switches, protocol gateways, serial-to-Ethernet converters, factory automation controllers, and embedded computing modules. The combination of low power, deterministic performance, and integrated networking interfaces makes it well-suited for these embedded networking scenarios. When designing with this part, ensure adequate thermal management for the BGA package, proper DDR signal integrity routing per NXP design guidelines, and careful power-rail sequencing to avoid latch-up. Reference NXP's P1014 hardware specifications document for the complete schematic and layout recommendations. This page synthesizes distributor pricing, drop-in compatible alternatives, and practical design guidance not found in the manufacturer datasheet alone, helping procurement and design engineers make informed component decisions.

견적 요청 문의하기
P1014NXN5DFB - QorIQ P1 800 MHz SoC w/ USB/SATA/GbE | NXP
P1014NXN5DFB

P1014NXN5DFB - QorIQ P1 800 MHz SoC w/ USB/SATA/GbE | NXP

The NXP QorIQ P1014NXN5DFB is a 32-bit Power Architecture SoC in the cost- and power-sensitive QorIQ P1 family, integrating an e500v2 core clocked up to 800 MHz with on-chip peripherals including USB, SATA, security (SEC), Gigabit Ethernet, PCI Express, and a DDR3 memory controller. The device is offered in a 425-pin TEPBGA package (19x19 mm, 0.8 mm pitch) and is qualified for the industrial -40C to +105C operating range. A QorIQ communications processor is a system-on-chip optimized for networking, industrial control, and secure-connected applications where a deterministic Power Architecture CPU and packet-handling accelerators replace a discrete MPU+ASIC pair. It sits at the boundary between general-purpose embedded processors and dedicated network processors, combining a CPU subsystem, memory controller, multiple high-speed serial interfaces, and security engines on a single die, which simplifies board layout and reduces BOM cost in cost-sensitive platforms. Key headline features include a 32-bit e500v2 core with up to 800 MHz operation, hardware-accelerated security (SEC) for cipher offload, integrated SATA controller for direct-attached storage, integrated Gigabit Ethernet MAC, PCI Express Gen1/Gen2 for high-speed expansion, DDR3 memory controller with ECC support, USB 2.0, and an industrial-grade temperature window. The 425-TEPBGA package exposes the full I/O set while keeping the board footprint small for routers, gateways, and industrial controllers. Technically the P1014 uses NXP's Power Architecture e500v2 core backed by a coherent platform, with a dedicated datapath engine, QUICC Engine compatibility, and SerDes lanes shared between SGMII, PCIe, and SATA interfaces. The on-chip SEC block accelerates AES, 3DES, SHA, and RSA, allowing IPsec, TLS, and MACsec without CPU bottlenecks - critical for secure gateways handling line-rate traffic. Typical applications include industrial IoT gateways, secure routers and firewalls, factory automation controllers, networked storage appliances (NAS/SAN edge nodes), and ruggedized telecom equipment. Designers favor this part when they need the Power Architecture determinism of older Freescale platforms with modern DDR3 and integrated GbE/SATA. When designing with the P1014NXN5DFB, pay close attention to the DDR3 fly-by topology, place the 0.8 mm pitch BGA decoupling directly under the die shadow, and provide a clean SerDes reference clock - these are the three most common bring-up pitfalls for QorIQ P1 designs. This page consolidates distributor pricing, end-of-life status, pin-compatible drop-in alternatives, and practical design notes not found in the manufacturer datasheet alone.

견적 요청 문의하기
P1014NXN5FFA - QorIQ P1 800MHz e500v2 MPU, 425-TEPBGA | NXP
P1014NXN5FFA

P1014NXN5FFA - QorIQ P1 800MHz e500v2 MPU, 425-TEPBGA | NXP

The NXP P1014NXN5FFA is a QorIQ P1 series communications processor featuring a single PowerPC e500v2 core running at 800 MHz, housed in a 425-ball TEPBGA (19x19 mm) package. Built on a 45 nm process, it integrates SEC crypto acceleration, dual GbE controllers, USB, SATA, PCIe, and a DDR3 memory controller for cost- and power-sensitive networking designs. A microprocessor (MPU) is an integrated circuit that contains the central processing unit (CPU) of an embedded system. In the hierarchy of computing silicon, an MPU sits between microcontrollers (MCUs with on-chip flash and peripherals) and full application processors (APs used in handsets and tablets). QorIQ communications processors target the industrial-networking and edge-router tier where deterministic packet processing, hardware crypto, and multi-protocol I/O are required without the cost of a high-end multicore SoC. Key features of the P1014NXN5FFA include a 32-bit Power Architecture core with dual-issue out-of-order execution, integrated SEC 4.4 security engine for IPSec/SSL/TLS acceleration, two 10/100/1000 Mb/s Ethernet MACs with QoS and virtualization support, two USB 2.0 ports (one host, one OTG), two SATA 2.0 ports, three PCIe Gen 2.0 controllers, and a 64-bit DDR3 memory controller up to 800 MT/s. The industrial-grade 'N' temperature rating extends the operating range to -40C to +105C, suiting outdoor and factory-floor deployments. The architecture combines a coherent core complex with a high-bandwidth interconnect fabric and a peripheral block complex. The e500v2 core includes hardware virtualization (hypervisor-aware), dual 32 KB L1 caches, a 256 KB unified L2 cache with ECC, and a 32-bit DDR controller with ECC for high-reliability operation. Hardware crypto offloads free the core for protocol processing, while the packet-processing engine accelerates classification and queue management. Typical applications include industrial Ethernet switches, IEC 61850-3 substation networking equipment, smart-grid gateways, factory automation controllers, networked printers, entry-level branch routers, and industrial IoT gateways that need deterministic networking, hardware security, and industrial temperature tolerance in a single chip. The compact 19x19 mm TEPBGA package also enables dense PCB layouts for line-card designs. When designing with this part, ensure the PCB has a minimum 6-layer stack-up with dedicated ground and power planes to handle the 800 MT/s DDR3 interface. The TEPBGA requires precise via-in-pad or microvia construction; improper escape routing will compromise DDR3 signal integrity. Reference the NXP hardware reference manual for SerDes reference-clock jitter and PCIe Gen 2 transmitter pre-emphasis settings. This page synthesizes distributor pricing, drop-in alternatives within the QorIQ P1 family, and practical design notes not found in the manufacturer datasheet, giving embedded engineers a fast path from MPN to BOM.

견적 요청 문의하기
P1014NXN5HFA - QorIQ P1 800MHz PowerPC e500v2 MPU | NXP
P1014NXN5HFA

P1014NXN5HFA - QorIQ P1 800MHz PowerPC e500v2 MPU | NXP

The NXP P1014NXN5HFA is a QorIQ P1 communications processor built on the PowerPC e500v2 core, running at up to 800 MHz with a 32-bit architecture, packaged in a 425-TEPBGA I (19x19 mm) thermally-enhanced plastic BGA. Per the NXP QorIQ P1010/P1014 product family datasheet, this SoC integrates USB, SATA, Gigabit Ethernet, PCIe, SEC crypto acceleration, and a DDR3 memory controller, targeting cost- and power-sensitive embedded networking and industrial applications. A communications SoC (System-on-Chip) is an integrated circuit that consolidates a CPU core, memory controller, and multiple peripheral interfaces onto a single die. The P1014 belongs to the QorIQ P1 tier of NXP's QorIQ family, which evolved from the PowerQUICC line and is built on Power Architecture technology. Within the broader hierarchy, it sits between low-cost microcontrollers and high-performance Layerscape processors, optimized for fanless industrial gateways, routers, and control-plane tasks. Key features of the P1014NXN5HFA include an 800 MHz e500v2 core, hardware-accelerated SEC security block, dual GbE MACs, three PCIe Gen 2 controllers, two SATA interfaces, two USB 2.0 ports, a DDR3/DDR3L memory controller with ECC support, and an extended-temperature grade of -40C to +105C. The 45 nm process technology provides a balanced power/performance envelope for embedded networking workloads without active fans. The architecture combines a single-threaded e500v2 execution core with a coherent system bus connecting to the platform's peripheral IP. The integrated SEC block offloads cryptographic operations such as AES, DES, SHA, and Kasumi, while the DDR3 controller with ECC supports memory reliability for industrial and networking deployments. The integrated communication interfaces reduce external component count, BOM cost, and PCB complexity. Typical applications include industrial Ethernet gateways, factory-automation controllers, secure routers and firewalls, telecom control-plane processors, networked printers, smart-grid edge nodes, and small-form-factor NAS/SAN appliances. The extended temperature range enables deployment in harsh industrial environments without thermal derating. When designing with the P1014NXN5HFA, ensure proper thermal management using the thermal pad exposed on the bottom of the 425-TEPBGA package, and follow NXP's hardware design guide for DDR3 trace length matching and PCIe reference clock routing to avoid signal-integrity issues. This page synthesizes distributor pricing, same-family NXP alternatives (P1014NXN5HFB, P1024NXN5HFA, P1010NXN5HFA), and practical design notes not consolidated in the manufacturer datasheet alone.

견적 요청 문의하기
P1014NXN5HHA557 - 800MHz QorIQ P1 MPU, 32-Bit PowerPC | NXP
P1014NXN5HHA557

P1014NXN5HHA557 - 800MHz QorIQ P1 MPU, 32-Bit PowerPC | NXP

The NXP P1014NXN5HHA557 is a 32-bit PowerPC e500v2 microprocessor from the QorIQ P1 family, integrating a single core running at 800 MHz and housed in a 425-terminal TEPBGA-I (19x19) package. The device targets power-sensitive embedded networking and industrial control applications, combining an integrated L1/L2 cache hierarchy with low-power operating modes. A microprocessor (MPU) is the central processing unit of an embedded system, integrating one or more CPU cores, cache, memory controllers, and a wide variety of peripheral interfaces on a single die. Within the embedded taxonomy, an MPU sits below a microcontroller (which typically adds on-chip flash and a smaller pin count) and above a discrete CPU + chipset combination, and it is commonly classified under the broader semiconductor / integrated circuit hierarchy. The QorIQ P1 series extends this hierarchy into the communications-processing segment, with the P1014 positioned as a low-power, single-core member for fanless or thermconstrained designs. Key features of the P1014NXN5HHA557 include a 32-bit e500v2 core with hardware double-precision floating-point support, integrated 32 KB L1 instruction and data caches, a 256 KB L2 cache, dual Gigabit Ethernet controllers with hardware acceleration, and DDR3/DDR3L memory controller support. The 800 MHz core delivers strong single-thread performance while the low-power design keeps typical power dissipation well below 1 W for thermally constrained enclosures. The P1014 architecture combines an out-of-order execution pipeline with a coherent crossbar fabric, allowing efficient on-chip traffic between the core, L2 cache, and integrated peripherals. NXP's proven e500v2 core and TEPBGA-I package provide robust thermal performance for industrial-grade environments, and the device supports multiple boot options including NAND flash, SPI, and SD/MMC interfaces. Typical applications include industrial gateways, networked printers, factory automation controllers, smart-grid energy management systems, and low-end LTE/4G small-cell base stations where the combination of Gigabit Ethernet, hardware crypto, and low power dissipation is highly valued. Designers should plan for a multi-rail power architecture and follow NXP's reference PCB layout for the TEPBGA-I package, paying particular attention to the high-speed DDR3 routing constraints and thermal dissipation through the package's thermal balls. This page synthesizes distributor pricing, drop-in alternatives, and practical design notes not found in the manufacturer datasheet.

견적 요청 문의하기
P1015NXN5DFB - QorIQ P1 667MHz PowerPC e500v2 MPU | NXP
P1015NXN5DFB

P1015NXN5DFB - QorIQ P1 667MHz PowerPC e500v2 MPU | NXP

The NXP P1015NXN5DFB is a single-core QorIQ P1 communications processor built on Power Architecture e500v2 technology, operating up to 667 MHz, and housed in a 561-pin TEPBGA I (23x23 mm) extended-temperature package. It integrates GbE controllers, DDR3 with ECC memory controller, PCIe, USB 2.0, and TDM interfaces for space-constrained networking and industrial designs. A communications processor (often called a networking SoC or communications MPU) is a specialized microprocessor that combines general-purpose CPU cores with high-bandwidth I/O peripherals and protocol accelerators for packet processing. QorIQ P1 parts sit in the hierarchy: communications processor -> embedded MPU -> microprocessor -> integrated circuit, with NXP positioning them below the P2/P4 multi-core families and above the older PowerQUICC II/III lines. The P1 family emphasizes extreme integration for fanless, low-power designs. Key features include a single e500v2 core with 32 KB I-cache and 32 KB D-cache, a 32-bit DDR3 SDRAM controller supporting up to 800 MT/s with ECC, three 10/100/1000 Mb/s Enhanced Three-Speed Ethernet (eTSEC) controllers with integrated PHYs, two PCI Express interfaces, USB 2.0 (host/device/OTG), four TDM interfaces, SPI, I2C, UART, and a security engine with XOR acceleration. The device operates across -40C to +125C industrial temperature range. The P1015NXN5DFB utilizes a 45 nm process technology delivering low power dissipation while sustaining 667 MHz operation. Its integrated peripherals eliminate the need for companion bridge chips, reducing BOM cost and PCB area. The 561-TEPBGA package exposes high-speed SerDes lanes with dedicated power/ground islands for signal integrity. Typical applications include industrial Ethernet switches, edge routers, factory automation controllers, defense communications equipment, smart grid substation gateways, and telecom access platforms. The wide -40C to +125C range makes it suitable for hardened outdoor installations. When designing with this device, allocate adequate PCB layers (minimum 8 layers) for SerDes routing, and use the DDR3 controller's fly-by topology for memory. Consult the NXP hardware reference manual for thermal management; the 561-TEPBGA requires careful PCB land pattern design and Xilinx-grade BGA assembly expertise. This page synthesizes distributor pricing, lifecycle data, and drop-in alternatives not found on the NXP product page, helping engineers assess obsolescence risk and procurement options for this QorIQ P1 communications processor.

견적 요청 문의하기
P1015SSE5FFB - QorIQ P1015 533MHz e500v2 SoC, 561-TEPBGA | NXP
P1015SSE5FFB

P1015SSE5FFB - QorIQ P1015 533MHz e500v2 SoC, 561-TEPBGA | NXP

The NXP (formerly Freescale) P1015SSE5FFB is a QorIQ P1 family communications processor built on the Power Architecture e500v2 core, running at 533 MHz with a 256 KB L2 cache, integrated into a 561-pin TEPBGA package (23 mm x 23 mm). The device integrates a GbE controller, DDR3 memory controller with ECC, PCIe, USB, TDM, and SEC (Security Engine) peripherals, targeting networking, telecom, and defense applications. A QorIQ communications processor is a system-on-a-chip (SoC) that combines one or more Power Architecture CPU cores with high-speed networking peripherals, memory controllers, and security accelerators on a single die. The P1 family sits in NXP's mid-range networking tier, below the P2/P3 multi-core devices, and is used as a control-plane processor in routers, switches, and wireless base stations. The 'QorIQ' name was introduced when Freescale transitioned the PowerQUICC product line to Power Architecture cores. Key features include a 32-bit PowerPC e500v2 core at 533 MHz, hardware cryptography (SEC 3.x), 32-bit DDR3 with ECC support, integrated three-port GbE switch, two PCI Express controllers, two USB 2.0 controllers (host + device), DUART, eSDHC, SPI, I2C, and TDM interfaces. The 561-TEPBGA package exposes all peripherals and provides ample signal integrity for GbE and PCIe at industrial temperature (0 to 105 C, suffix SE5 indicates 'Standard Temperature, Enhanced security, Rev 1.x, 533 MHz speed bin'). Architecturally, the P1015SSE5FFB uses a single e500v2 core with a 7-stage pipeline, Book-E MMU, and signal-processing extensions. The on-chip SEC block accelerates DES/3DES, AES, SHA-1/2, RSA, and public-key operations, offloading IPsec and TLS tasks from the CPU. The integrated three-port Gigabit Ethernet switch (with classification and QoS hardware) removes the need for an external GbE switch in small-port-count designs, lowering BOM cost for entry-level routers and CPE devices. Typical applications include industrial routers and gateways, Ethernet switches, network appliances, defense and aerospace embedded computing, smart-grid communications, factory-floor IoT aggregation, and secure VPN concentrators. The device's hardware encryption engine makes it particularly attractive for IPsec tunnel termination in branch-office VPN appliances. When designing with the P1015SSE5FFB, ensure the 533 MHz speed bin is sufficient for your packet-forwarding workload, and confirm DDR3-800/1066 trace lengths meet the data-sheet routing rules. The 561-TEPBGA package requires multi-layer PCB with buried vias for breakout routing; plan for at least an 8-layer stack-up with controlled-impedance Ethernet and PCIe pairs. This page synthesizes distributor pricing, drop-in pin-compatible alternatives across the QorIQ P1 family, application notes, and practical layout guidance beyond what is found in the bare manufacturer datasheet, helping engineers select the right P1015 speed bin and verify second-source availability.

견적 요청 문의하기
P1020NSE2FFB - QorIQ P1 Dual-Core 800MHz SoC | NXP Semiconductors
P1020NSE2FFB

P1020NSE2FFB - QorIQ P1 Dual-Core 800MHz SoC | NXP Semiconductors

The NXP (formerly Freescale) P1020NSE2FFB is a QorIQ P1 series dual-core communications processor built on Power Architecture e500v2 cores, running at 800 MHz, and housed in a 689-pin TEBGA II (31x31 mm) package with exposed thermal pad for high-power networking applications. The P1 platform series delivers up to 2.4 GHz of combined compute, with integrated peripherals for unified networking and industrial workloads. A QorIQ communications processor is a multicore system-on-chip designed by NXP for routers, switches, WAN optimization, and industrial control. It typically integrates CPU cores, a high-bandwidth system bus, DDR memory controller, Ethernet MACs, PCIe, USB, security engines, and TDM interfaces, replacing multiple discrete components on legacy PowerQUICC designs. The QorIQ P1 sits within the broader Power Architecture / PowerQUICC family hierarchy (e500v2 core -> dual-core SoC -> QorIQ P1 platform -> Power Architecture networking SoC -> embedded processor). Key features include dual e500v2 cores at 667/333/667 MHz core-to-platform ratios, DDR2/DDR3 memory controller with ECC, GbE interfaces, integrated SEC security engine, PCIe, USB 2.0, and TDM. Operating temperature spans 0C to 125C junction, making the part suitable for industrial and networking environments with elevated ambient temperatures. The architecture combines high-throughput on-chip interconnect, dual-issue in-order execution cores, and a flexible peripheral set. The 45 nm process enables tighter power budgets versus prior PowerQUICC III devices. According to NXP product literature, P1020 series parts support hardware-accelerated encryption, QoS queues, and pattern matching for deep-packet inspection at line rate. Typical applications include multiservice routers, industrial gateways, defense and aerospace controllers, factory automation nodes, secure VPN appliances, and LTE/WiMAX base-station control planes. The combination of two cores plus integrated GbE MACs makes it well-suited for fan-out on a backplane while the SEC engine handles IPsec without burdening the cores. Design considerations include robust thermal dissipation due to the 31x31 mm BGA exposed pad, careful signal-integrity work for DDR3 at 667 MHz, and provision for boot ROM and NAND flash for secure boot chains. Power sequencing of the 1.0 V core and 1.5/1.8 V DDR rails must follow the reference manual to avoid I/O damage. This page consolidates distributor pricing, drop-in alternatives from the same QorIQ P1 family, and practical design considerations not assembled in a single place on the manufacturer datasheet.

견적 요청 문의하기
P1020NSN2FFB - QorIQ P1020 667MHz Dual-Core SoC | NXP
P1020NSN2FFB

P1020NSN2FFB - QorIQ P1020 667MHz Dual-Core SoC | NXP

The NXP P1020NSN2FFB is a QorIQ P1 platform Power Architecture 32-bit system-on-chip featuring two e500v2 cores running at up to 667 MHz, integrated into a 689-pin TEPBGA II (31x31 mm) package. The device integrates dual Gigabit Ethernet controllers, DDR2/DDR3 memory controller with ECC support, PCIe interfaces, USB 2.0, TDM, and security engines on a single 45 nm die, targeting cost-sensitive networking applications. A QorIQ communications processor is a system-on-chip that combines one or more Power Architecture CPU cores with high-speed networking peripherals, security accelerators, and memory/IO controllers on a single die. As part of the broader QorIQ family (P1, P2, P3, P4 series), the P1 platform targets entry-level to mid-range networking and industrial equipment. The hypernym hierarchy is: SoC -> microprocessor -> communications processor -> networking SoC. The P1020NSN2FFB is pin-compatible with other members of the QorIQ P1 series, enabling scalable product designs from single-core (P1011) to dual-core (P1020) configurations on the same PCB. Key features of the P1020NSN2FFB include dual 667 MHz e500v2 cores with 32 KB L1 instruction and data caches per core, a 256 KB shared L2 cache with ECC, hardware cryptography acceleration, four Gigabit Ethernet ports with MACsec support, three PCIe Gen 1 controllers, two USB 2.0 controllers (host and device), TDM interface for legacy telecom, and a high-bandwidth DDR2/DDR3 memory controller supporting up to 8 GB of addressable memory with ECC. The integration reduces BOM count and PCB complexity versus discrete CPU-plus-ASIC designs. Architecturally, the P1020NSN2FFB uses NXP's e500v2 core, which supports dual-issue superscalar execution, hardware floating-point, and a memory management unit tuned for embedded networking workloads. The on-chip Data Path Acceleration Architecture (DPAA) enables line-rate packet processing at gigabit speeds by offloading buffer management and queue scheduling from the cores. Typical applications include industrial networking gateways, smart grid routers, factory automation controllers, multi-service routers, network-attached storage (NAS), and telecom edge equipment. The dual-core architecture enables concurrent control-plane and data-plane processing on a single SoC. When designing with this device, allocate adequate thermal dissipation for the TEPBGA II package: at typical 6-8W dissipation, a multi-layer PCB with thermal vias beneath the BGA is mandatory. Plan DDR routing carefully with matched trace lengths and proper impedance control to maintain signal integrity at 667 MHz core speeds. This page synthesizes distributor pricing, pin-compatible alternatives, and practical design considerations derived from NXP QorIQ P1 datasheets, not found on any single manufacturer page.

견적 요청 문의하기
P1020NSN2HFB - QorIQ P1 2-Core 800MHz SoC MPU | NXP
P1020NSN2HFB

P1020NSN2HFB - QorIQ P1 2-Core 800MHz SoC MPU | NXP

The NXP P1020NSN2HFB is a PowerPC e500v2 microprocessor IC from the QorIQ P1 platform series, integrating 2 cores running up to 800 MHz, a 32-bit architecture, and a rich communications peripheral set on a single 689-TEPBGA II (31x31 mm) package. It is qualified for 0C to 125C operation and ships as silicon revision 1.1 with the product identifier string "800/400/667 ST NE r1.1", indicating 800 MHz core / 400 MHz platform / 667 MHz DDR clock targets. The device combines dual e500v2 cores with DDR2/DDR3 memory controller (with ECC), Gigabit Ethernet, PCI Express, USB 2.0, and TDM interfaces, targeting networking, telecom, aerospace, defense, and industrial control applications where high integration replaces multi-chip designs. A microprocessor (MPU) in the QorIQ family is a system-on-chip (SoC) processor integrating CPU cores, memory controllers, and high-speed serial I/O on one die. Within the broader taxonomy, the P1020NSN2HFB is a Power Architecture (PowerPC) embedded microprocessor - the direct successor to the PowerQUICC III communications processors - sitting in the hierarchy: microprocessor -> embedded processor -> networking/communications SoC -> QorIQ P1 platform. Unlike a microcontroller (MCU), an MPU like the P1020NSN2HFB is designed to run a full operating system (Linux, VxWorks) and external DRAM, not bare-metal firmware with on-chip flash. Key features of the P1020NSN2HFB include dual e500v2 cores at 800 MHz with integrated L1/L2 caches, a 64-bit DDR2/DDR3 SDRAM controller supporting ECC for high-reliability memory subsystems, three PCI Express interfaces (one x4 + two x1), dual Gigabit Ethernet controllers with SGMII support, USB 2.0, TDM, SPI, I2C, and hardware encryption engines. The platform runs at 400 MHz while DDR can be clocked up to 667 MHz, providing balanced memory throughput for packet processing workloads. Architecturally, the P1020NSN2HFB uses a coherent dual-core e500v2 implementation with a shared L2 cache and a high-bandwidth system bus. Built on a 45 nm process, it dissipates on the order of 5 W under typical networking loads, making it suitable for fanless industrial designs with proper thermal management. The integrated datapath acceleration engine (DPAA) offloads packet classification, queue management, and crypto from the cores, which is critical for line-rate gigabit routing and switching. Typical applications include branch-office routers, industrial Ethernet gateways, factory automation controllers, defense radios, and avionics networking subsystems where deterministic dual-core performance, hardware offload, and extended temperature qualification (0 to 125C junction) matter. Pairing the SoC with DDR3 ECC memory and a managed PHY creates a compact, high-reliability networking platform. When designing with this part, allocate a 31x31 mm PCB footprint with a via-in-pad thermal array to dissipate the ~5 W typical load, and follow NXP's reference design for DDR3-667 trace length matching. Per the manufacturer part page, the standard P1020NSN2HFB is being moved toward End of Life; verify last-time-buy windows or migrate to the P1020NSN2HFB-Q1 (AEC-Q100) variant for automotive-grade designs. This page synthesizes distributor pricing, drop-in alternatives in the same 689-TEPBGA II package, parametric comparisons vs P1011 and P1022 variants, and practical hardware design notes not found in the manufacturer datasheet alone.

견적 요청 문의하기
P1020NXE2FFB - QorIQ P1 Dual-Core 800MHz SoC | NXP
P1020NXE2FFB

P1020NXE2FFB - QorIQ P1 Dual-Core 800MHz SoC | NXP

The NXP P1020NXE2FFB is a QorIQ P1 series communications processor based on the Power Architecture e500v2 core, integrating two 32-bit cores running up to 800 MHz in a 689-pin TEPBGA II (31x31 mm) package. It combines GbE, DDR2/DDR3 with ECC memory controller, PCIe, USB, TDM, and SEC security acceleration in a single system-on-chip targeted at industrial and extended-temperature networking applications. A microprocessor (MPU) is an integrated circuit that contains one or more central processing units, cache, memory controllers, and peripheral interfaces on a single die. Within the broader taxonomy, an MPU is a sub-class of microcontroller/microprocessor IC, which itself sits under Integrated Circuits > Microprocessors. The QorIQ P1 family, derived from the PowerQUICC lineage, represents NXP's value-tier communications processors used in wired and wireless access, industrial control, and printing/imaging platforms. Key features include dual e500v2 cores with 36-bit physical addressing, integrated SEC 4.0 security engine for IPSec/SSL acceleration, three Gigabit Ethernet interfaces (two SGMII plus one RGMII), two PCIe Gen 1 controllers, a USB 2.0 controller with ULPI interface, DDR2/DDR3 memory controller with ECC, and four TDM channels. The device operates from -40C to +125C junction temperature, making it suitable for extended-temperature industrial and outdoor networking equipment. Architecturally, the P1020NXE2FFB employs the e500v2 core with double-precision FPU, 32KB I/D L1 cache per core, and a unified 256KB L2 cache. The platform uses a CoreNet fabric for on-chip interconnect, a separate MAPLE-B2 acceleration engine for print/imaging offload, and the SEC 4.0 hardware crypto block supporting DES, 3DES, AES, ARC4, RSA, ECC, and MD5/SHA-1/SHA-2 hashes. Typical applications include multi-service routers, DSLAM line cards, industrial gateways, network-attached storage controllers, multi-function printer controllers, and Smart Energy/Grid communication nodes. The combination of dual-core processing and hardware cryptography makes it ideal for VPN/SSL termination at the network edge. When designing with the P1020NXE2FFB, ensure the DDR3 interface is terminated per JEDEC recommendations and that the core voltage rails (0.9V/1.0V, 1.5V, 3.3V) are sequenced according to the power-up requirements. Heat dissipation at 800 MHz is moderate but the 31x31 mm BGA still requires thermal vias and adequate PCB copper for sustained 125C operation.

견적 요청 문의하기
P1020NXN2FFB - QorIQ P1 Dual-Core 800MHz SoC, 689-TEPBGA | NXP
P1020NXN2FFB

P1020NXN2FFB - QorIQ P1 Dual-Core 800MHz SoC, 689-TEPBGA | NXP

The NXP P1020NXN2FFB is a QorIQ P1 series dual-core Power Architecture (e500v2) communications processor operating up to 800 MHz, housed in a 689-ball TEPBGA II (31x31 mm) package with extended industrial temperature range (-40C to +125C). It integrates dual 32-bit Power Architecture cores, a GbE interface, DDR2/DDR3 memory controller with ECC, PCIe, USB, and TDM links on a single silicon die manufactured in 45 nm CMOS process, marking silicon revision R1.1 of the P1020 family. A QorIQ communications processor is a multi-core system-on-chip (SoC) designed for power-efficient packet processing in networking and industrial applications. QorIQ processors sit in the taxonomy: communications SoC -> networking processor -> embedded MPU, occupying the space where high-performance control plane and data plane functions converge on a single chip. The P1020 family specifically targets cost- and power-optimized designs such as industrial routers, secure gateways, and factory automation controllers where deterministic real-time response and energy efficiency matter more than raw gigahertz throughput. Key features of the P1020NXN2FFB include two e500v2 cores at 667 MHz (1.0 GHz capable depending on SKU), integrated security engine, dual Gigabit Ethernet MACs, a 64-bit DDR2/DDR3 memory controller with ECC supporting up to 4 GB, two PCIe Gen1 lanes, two USB 2.0 controllers, multiple TDM ports, and SerDes-based high-speed interfaces. The extended -40C to +125C junction temperature rating (suffix NXN) makes the 'FFB' grade suitable for harsh-environment deployments such as outdoor industrial switches, substation automation, and ruggedized military networking. Architecturally, the device implements a hierarchical bus topology with the cores feeding into the CoreNet coherency fabric, isolating traffic from the peripheral I/O subsystem. This design allows deterministic interrupt latency while sustaining line-rate Gigabit throughput on the packet-processing engines. Typical applications include industrial control routers, energy/utility smart grid gateways, telecom subscriber equipment, factory-automation controllers requiring extended temperature operation, and secure edge appliances where hardware-accelerated cryptography is required alongside networking intelligence. Designers should pay close attention to power-rail sequencing (1.0V core, 1.5V DDR, 3.3V I/O), thermal management at full load (ball-grid cooling capability), and DDR3 signal integrity matching the 64-bit ECC bus at 667 MHz operation. Reference schematics and validated BOMs from the NXP QorIQ P1020 hardware developer's user guide are strongly recommended. This page consolidates distributor pricing, pin-compatible QorIQ P1020/P1011 family drop-in alternatives, and design notes not duplicated in the manufacturer datasheet, providing engineering value beyond the bare datasheet text.

견적 요청 문의하기
P1020NXN2HFB - QorIQ P1 Dual-Core 800MHz MPU | NXP Semiconductors
P1020NXN2HFB

P1020NXN2HFB - QorIQ P1 Dual-Core 800MHz MPU | NXP Semiconductors

The NXP P1020NXN2HFB is a dual-core PowerPC e500v2 microprocessor in the QorIQ P1 communications platform family, integrating two 32-Bit cores running at 800 MHz into a 689-TEPBGA II package (31x31 mm) with exposed thermal pad. The part is positioned by NXP as a value-oriented communications processor for networking, telecom, aerospace, defense, and industrial markets, providing dual-core performance and a rich peripheral set in the 533 MHz to 800 MHz range while retaining advanced security features. Background: An MPU (Microprocessor Unit) in this category is the principal CPU of an embedded compute platform, distinct from a microcontroller in that it typically relies on external memory (DDR, NOR/NAND) and an external chipset for I/O. Within NXP's portfolio, the QorIQ P1 series sits below the P2/P3 layerscale parts and above the legacy PowerQUICC line; the P1020 is the dual-core sibling of the single-core P1011, sharing a common pinout and reference platform. The package name 689-TEPBGA II denotes a 31x31 mm thermally-enhanced plastic BGA with 689 balls. Key features include two Power Architecture e500v2 cores with hardware MMU and double-precision FPU support, integrated security engine with protocol acceleration, integrated DMA, multiple 10/100/1000 Ethernet MACs, PCI Express controllers, USB, SDHC, I2C, SPI, UART, and TDM interfaces. According to the vendor product family, the P1 series is built on a 45 nm process and optimized for power-efficient packet processing. Typical applications include industrial control gateways, secure routers and firewalls, networked printers and PoS terminals, defense and aerospace embedded controllers, factory-floor protocol converters, and edge telecom line cards. The dual-core configuration allows one core to run a control-plane stack while the second handles data-plane forwarding. Design consideration: the 689-ball BGA requires controlled-impedance PCB stack-up with matched-length DDR traces and a solid thermal copper pour under the exposed pad; designers should evaluate NXP's validated reference designs before board bring-up. This page consolidates distributor pricing, lifecycle status (currently End-of-Life per NXP), recommended drop-in same-family alternatives, and design considerations not always collated in a single vendor datasheet.

견적 요청 문의하기