ADS830E/2K5 - 8-Bit 60 MSPS ADC | Texas Instruments
부품 번호: ADS830E/2K5 ✓ 활성ADS830E/2K5 개요
An ADC is a data-converter IC that samples an analog voltage and converts it into a digital code for processing, storage, or transmission. The ADS830 belongs to the pipelined ADC hierarchy, where internal stages operate concurrently to achieve a high sampling rate. Its 8-bit quantizer represents each sampled analog level with eight bits, providing a compact data path for video digitization, medical imaging, communications, and instrumentation.
Principal specifications include a maximum sampling frequency of 60 MSPS, 49.5 dB signal-to-noise ratio, 0.2 LSB differential nonlinearity, and 170 mW power consumption. The analog input can be single-ended or differential, while the input range is programmable to support different signal amplitudes. An internal reference option reduces external circuitry, although an external reference can be selected when system-level accuracy requires it.
The converter uses a high-bandwidth track-and-hold circuit preceding its pipelined 8-bit quantizer. This architecture supports rapid conversion rates and provides separate single-ended or differential operating modes. Texas Instruments describes the device as pin-for-pin compatible with the 8-bit, 80 MSPS ADS831, allowing a board to support a faster sampling option without changing its SSOP-20 footprint.
Typical applications include medical-imaging signal chains, video digitization, communications equipment, and test instrumentation. The 60 MSPS rate is appropriate for digitizing intermediate-frequency or sampled-video waveforms, while differential operation can improve rejection of common-mode noise in balanced analog circuits. The single +5 V supply also simplifies integration with conventional +5 V digital processing logic.
Design the input network for the selected single-ended or differential range and account for the ADC input bandwidth when placing the sampling circuit. Reference and supply decoupling should be placed close to their associated pins, while high-speed routing requires short, controlled-impedance connections and a quiet return path. Confirm timing for the parallel output interface against the acquisition clock and downstream logic.
This page combines the manufacturer specifications, drop-in compatibility information, application guidance, and engineering design notes in one searchable reference. The comparison table and selection guide clarify when the 60 MSPS ADS830E/2K5 or the faster pin-compatible ADS831 is the appropriate choice for a new design.
드롭인 대체품: ADS830E/2K5 — 동일 패키지, 핀 호환. PCB 재작업이 필요한 다른 패키지 부품은 제외됩니다.
이 시리즈의 변형
다음과 드롭인 호환되는 동일 시리즈 모델: ADS830E/2K5 (동일 폼 팩터 및 풋프린트) — 차이점: Package, Architecture, Resolution, Operating Temperature Range, RoHS Status.
ADS8318IDRCR
✅ 드롭인가격 문의
데이터시트 보기 →ADS830E/2K5 최대 정격 & 전기적 특성
| ADC Resolution | 8 bit |
| Maximum Sampling Rate | 60 MSPS |
| Architecture | Pipelined CMOS ADC |
| Number of Input Channels | 1 channel |
| Input Configuration | Single-ended or differential |
| Programmable Input Range | 1 Vpp or 2 Vpp |
| Single-Ended Input Range | 1.5 V to 3.5 V |
| Signal-to-Noise Ratio | 49.5 dB |
| Differential Nonlinearity | 0.2 LSB |
| Power Consumption | 170 mW |
| 공급 전압 | +5 V |
| Reference | Internal or external |
| Quantizer Resolution | 8 bit |
| 동작 온도 범위 | -40 C to +85 C |
| 패키지 | 20-pin SSOP |
| Output Interface | Parallel |
ADS830E/2K5 20-pin ssop 핀 구성 가이드
ADS830E/2K5(20-pin ssop 패키지)의 핀 구성입니다. 이 아날로그 부품에는 입력, 출력, 전원 공급 핀이 있습니다. 오프셋 널, 보상, 인에이블 핀 구성은 제조사 데이터시트를 참조하십시오. 신호 컨디셔닝 및 증폭기 회로에 이상적입니다.
다음에 대한 상세 핀아웃 데이터 없음: ADS830E/2K5.
다음을 참조하십시오: 데이터시트 전체 핀 구성은 다음을 참조하십시오.
일반적인 애플리케이션
ADS830E/2K5 적합 용도: 6 애플리케이션s: Medical Imaging Signal Acquisition, Video Digitization, Communications IF Signal Processing, Test and Measurement Instrumentation, Industrial Data Acquisition, Portable Diagnostic Equipment.
Medical Imaging Signal Acquisition
The ADS830E/2K5 suits medical-imaging signal acquisition stages that require compact 8-bit digitization at up to 60 MSPS. Its 49.5 dB SNR and 0.2 LSB differential nonlinearity support accurate conversion of sampled analog waveforms, while the 20-pin SSOP package reduces board area. In a typical signal chain, an amplifier drives the single-ended or differential ADC input and the parallel output connects to a digital acquisition controller. Differential operation is useful when the source has balanced geometry or when rejecting common-mode noise is important. The 170 mW power specification also helps limit thermal loading in dense instrumentation. System designers must still validate signal bandwidth, isolation requirements, clock timing, and the medical-device standards applicable to the completed equipment.
추천
Video Digitization
The ADS830E/2K5 can digitize video-related analog signals at up to 60 MSPS when 8-bit resolution and a parallel output are sufficient. Its pipeline architecture supports repetitive sampling, and the programmable 1 Vpp or 2 Vpp input range allows the analog front end to be scaled to the source amplitude. A practical implementation places the video amplifier or attenuator close to the ADC, followed by short traces to the clock and parallel data outputs. The 170 mW operating power is particularly helpful in compact camera and monitor electronics. Before implementation, verify the required pixel clock, analog bandwidth, settling behavior, output timing, and whether the faster 80 MSPS ADS831 would provide a useful acquisition-time margin.
추천
Communications IF Signal Processing
The ADS830E/2K5 is appropriate for digitizing intermediate-frequency or other communications waveforms when an 8-bit converter operating at 60 MSPS meets the system requirement. The selectable single-ended or differential input supports both simple source interfaces and balanced RF downconverter outputs, while differential operation can reduce common-mode pickup. Its internal-reference option simplifies the basic analog subsystem, and the external-reference option permits clock- or system-level reference architecture. The parallel interface allows direct connection to FPGA or digital logic when timing is correctly aligned. Designers should calculate the required Nyquist margin, inspect harmonic and distortion behavior at the operating signal level, and provide controlled-impedance routing for clocks and data to avoid degrading the available 49.5 dB SNR.
추천
Test and Measurement Instrumentation
The ADS830E/2K5 can serve as the sampling front end in waveform, communication, or automated test equipment when 8-bit resolution at 60 MSPS is sufficient. The fast track-and-hold stage captures repetitive inputs, while selectable differential operation helps reject offset and common-mode interference in instrumented systems. A practical design routes the measured signal through an attenuator or amplifier into the ADC, then synchronizes the parallel data output with a clocked controller or FPGA. Using the internal reference minimizes support components, while selecting an external reference can support a more controlled measurement calibration scheme. Validate gain accuracy, bandwidth, aperture behavior, clock jitter, and output timing in the final instrument. For workloads needing shorter acquisition intervals, the pin-compatible 80 MSPS ADS831 may reduce conversion time.
추천
Industrial Data Acquisition
The ADS830E/2K5 supports compact industrial acquisition modules that must convert analog sensor or process signals at up to 60 MSPS. Its single +5 V supply simplifies integration with conventional control electronics, and the 20-pin SSOP package limits footprint requirements compared with larger converter packages. Differential input can be selected for sensor interfaces and balanced lines where common-mode rejection is beneficial, while single-ended operation simplifies less demanding channels. The parallel output connects naturally to acquisition logic or an FPGA when timing margins are managed correctly. At the board level, isolate analog and digital return currents, place bypass capacitance near the supply and reference pins, and use short clock routing. Confirm the sensor bandwidth, environmental temperature range, grounding strategy, and production test requirements before deployment.
추천
Portable Diagnostic Equipment
The ADS830E/2K5 is suitable for portable diagnostic and monitoring equipment where rapid, compact 8-bit conversion is needed within a limited power budget. Its 170 mW operating-power specification helps reduce heat in a battery-powered enclosure, and the SSOP-20 package supports compact assembly. The converter can capture pulsed or repetitive analog events when the front end preserves the required bandwidth and the acquisition clock is synchronized to the source. Differential operation is advantageous for probe, sensor, or balanced test interfaces, whereas single-ended operation reduces analog complexity. The parallel data bus requires enough board area for routing and may drive an FPGA, microcontroller, or dedicated capture logic. Validate battery-energy demand, clock jitter, input settling, data timing, and the thermal rise of the assembled device during worst-case sampling.
추천
추천 제품 요약
엔지니어링 참조 데이터: ADS830E/2K5 — 비교, 설계 지침 및 규정 준수 정보.
선택 가이드
대체품과의 비교
| 파라미터 | 이 제품 | ADS831 |
|---|---|---|
| Package | 20-pin SSOP | 20-pin SSOP, pin-for-pin compatible |
| Brand | Texas Instruments | Texas Instruments |
| Resolution | 8 bit | 8 bit |
| Maximum Sampling Rate | 60 MSPS | 80 MSPS |
| Supply Voltage | +5 V | +5 V |
주요 차별점
- Lower 60 MSPS operating point than the pin-compatible ADS831 (vs ADS831)
- Documented 49.5 dB signal-to-noise performance (vs ADS831)
- 170 mW operating-power specification (vs ADS831)
- Pin-compatible upgrade path without footprint changes (vs ADS831)
설계 노트
Keep the acquisition clock, analog input, and parallel output paths short, and provide a continuous return plane beneath high-speed signals. The 60 MSPS conversion rate requires attention to clock jitter and edge quality because timing variation can degrade conversion SNR. Route the clock away from sensitive analog inputs and use a compact, symmetrical output arrangement that minimizes data-bus skew between the ADC and the receiving logic.
Place input, reference, and supply bypass components close to their associated pins, and keep the analog return path separate from digital clock and output currents. Use the datasheet reference and decoupling network unchanged where possible because component placement and loop area can influence noise and distortion. Confirm that the SSOP footprint, pad geometry, solder profile, and assembly orientation match the manufacturer land pattern before releasing a PCB.
Estimated: the converter's stated 170 mW operating power corresponds to approximately 34 mA from a 5 V rail. This estimate uses the published 5 V supply and 170 mW power values. Actual supply current can vary with operating conditions, so validate the regulator headroom and power budget across sampling mode, reference selection, temperature, and load. Provide local bypass capacitance to prevent data-converter switching activity from disturbing adjacent analog circuitry.
Do not assume that a shared package alone guarantees identical operation. The ADS831 is pin-for-pin compatible with the ADS830 but increases the maximum sampling rate from 60 MSPS to 80 MSPS, so review clock timing, acquisition timing, output latency, power, and analog bandwidth before substitution. Also verify the selected single-ended or differential input range; the programmable ranges and reference configuration must match the external signal source.
규정 준수 정보
The ADS830 is an analog-to-digital converter rather than an automotive-qualified device. RoHS, REACH, lead-free, halogen-free, and conflict-minerals status require confirmation from current manufacturer product documentation.