AD7472YRU - 12-Bit 1.5 MSPS ADC | Analog Devices
부품 번호: AD7472YRU ✓ 활성AD7472YRU 개요
An ADC is a data-acquisition IC that converts an analog voltage into a digital code. The AD7472 belongs to the parallel-output SAR ADC family, combining a 12-bit resolution, 1.5 MSPS sampling capability, and low 4 mW power operation in a single package. The AD7470 is the related 10-bit member of the family, while AD7472 provides the higher resolution needed when the input-to-output quantization step must be smaller.
Key characteristics include 12-bit resolution, 1.5 MSPS maximum throughput, a 2.7 V to 5.25 V analog supply range, and a low-noise internal reference. The parallel interface presents the conversion result across dedicated digital output pins, allowing direct connection to a microcontroller, FPGA, DSP, or logic device without requiring a serial data link.
The successive-approximation architecture performs one conversion through a sequence of internal comparator decisions. Its throughput is suitable for industrial process monitoring, sensor acquisition, portable measurement equipment, and embedded control loops. Because the interface is parallel, the host processor must be able to accept and latch 12 bits of conversion data within the available acquisition interval.
A typical implementation places the AD7472 close to the analog input source and routes its digital outputs to a logic device. Short analog traces reduce pickup of noise and switching artifacts, while a solid ground plane and careful separation of analog and digital return currents help preserve conversion accuracy. The manufacturer datasheet should be consulted for the complete pin-description table, recommended input and reference circuits, and acquisition timing diagrams.
The AD7472YRU is suited to designers who require a parallel-output SAR converter with a compact 24-pin TSSOP footprint. AD7472ARU and AD7472BRU provide related temperature-grade choices, while the AD7470 members trade resolution for higher throughput. This page also organizes pricing evidence, replacement guidance, comparison parameters, and practical design notes for faster component selection.
드롭인 대체품: AD7472YRU — 동일 패키지, 핀 호환. PCB 재작업이 필요한 다른 패키지 부품은 제외됩니다.
이 시리즈의 변형
다음과 드롭인 호환되는 동일 시리즈 모델: AD7472YRU (동일 폼 팩터 및 풋프린트) — 차이점: Package, Input Type, Number of Channels, Resolution, Architecture.
AD7472ARUZ-REEL
✅ 드롭인 ⚠️ 사양 미검증가격 문의
데이터시트 보기 →AD7472BRU-REEL
✅ 드롭인가격 문의
데이터시트 보기 →AD7470ARU
✅ 드롭인 ⚠️ 사양 미검증📋 참조 대체품 (카탈로그에 없음)
AD7470BRU
✅ 드롭인 ⚠️ 사양 미검증📋 참조 대체품 (카탈로그에 없음)
AD7472YRU 최대 정격 & 전기적 특성
| ADC Type | Successive-approximation ADC |
| 분해능 | 12 bit |
| Number of Channels | 1 channel |
| Input Type | Single-ended analog input |
| 샘플링 속도 | 1.5 MSPS |
| Supply Voltage Range | 2.7 V to 5.25 V |
| Power Consumption | 4 mW |
| Output Interface | Parallel |
| 패키지 | 24-pin TSSOP |
| Package Type | TSSOP-24 |
| 실장 유형 | Surface Mount |
| Reference | Internal low-noise reference |
AD7472YRU tssop-24 핀 구성 가이드
AD7472YRU(tssop-24 패키지)의 핀 구성입니다. 이 아날로그 부품에는 입력, 출력, 전원 공급 핀이 있습니다. 오프셋 널, 보상, 인에이블 핀 구성은 제조사 데이터시트를 참조하십시오. 신호 컨디셔닝 및 증폭기 회로에 이상적입니다.
다음에 대한 상세 핀아웃 데이터 없음: AD7472YRU.
다음을 참조하십시오: 데이터시트 전체 핀 구성은 다음을 참조하십시오.
일반적인 애플리케이션
AD7472YRU 적합 용도: 6 애플리케이션s: Industrial Sensor Acquisition, Precision Data-Acquisition Systems, Embedded Control and Monitoring, Portable Measurement Instruments, Audio and Vibration Monitoring, FPGA-Based Signal Processing.
Industrial Sensor Acquisition
The AD7472YRU is suitable for acquiring conditioned pressure, temperature, or position signals in industrial measurement systems. Its 12-bit resolution provides a finer digital representation than the 10-bit AD7470 family, while the 1.5 MSPS rate supports moderately fast process-control updates. Place the converter near the sensor interface to keep the analog input trace short, then latch the parallel outputs in an FPGA or microcontroller. The single 2.7 V to 5.25 V supply range supports both 3.3 V and 5 V designs, reducing the number of rails required around the acquisition chain.
추천
Precision Data-Acquisition Systems
The 12-bit resolution and 1.5 MSPS throughput of the AD7472YRU fit compact precision DAQ modules that digitize several slow or medium-speed analog channels through multiplexing. Its parallel output allows the host processor to capture each code with a straightforward digital interface, avoiding the serial overhead of a serial-output converter. The 24-pin TSSOP package also supports dense board layouts, although a dedicated ground plane and short analog routing remain important for preserving measurement quality.
추천
Embedded Control and Monitoring
The AD7472YRU can serve as the analog front end of an embedded controller that monitors a condition, pressure, or analog process variable and updates a control loop. Its 1.5 MSPS maximum rate is sufficient for many feedback and monitoring tasks, while 12-bit quantization gives the controller more useful information about small input changes. Connect its parallel outputs to the host MCU or DSP and use the acquisition timing from the manufacturer datasheet to establish the conversion and data-latch interval.
추천
Portable Measurement Instruments
The low 4 mW power operation and 2.7 V to 5.25 V supply range of the AD7472YRU suit battery-powered handheld measurement equipment. A 3.3 V implementation can reduce both supply complexity and converter power demand compared with a higher-voltage analog rail, while the parallel outputs can be handled by a low-power embedded controller. Low power does not remove the need for careful reference grounding and analog layout, so the input network and bypass components should remain close to the device.
추천
Audio and Vibration Monitoring
The AD7472YRU can be used for low-frequency vibration, acoustic, or waveform monitoring where the 12-bit resolution improves visibility of small signal changes and the 1.5 MSPS rate captures the required bandwidth. Place the converter at the output of a low-noise amplifier and anti-alias filter, and route the parallel output to an FPGA timing engine. The application must account for the 10-bit AD7470's higher 1.75 MSPS rate when sampling requirements prioritize maximum speed over output resolution.
추천
FPGA-Based Signal Processing
The parallel data bus of the AD7472YRU maps naturally onto an FPGA acquisition pipeline, allowing the conversion code to be captured, filtered, or integrated without a serial interface. The 12-bit output and 1.5 MSPS throughput support continuous moderate-rate sampling, while the 24-pin TSSOP package allows placement near the analog front end. Designers should time the latch event from the acquisition sequence in the manufacturer datasheet and keep digital output routing away from the sensitive analog input and reference paths.
추천
추천 제품 요약
엔지니어링 참조 데이터: AD7472YRU — 비교, 설계 지침 및 규정 준수 정보.
선택 가이드
대체품과의 비교
| 파라미터 | 이 제품 | AD7472ARU | AD7472BRU | AD7470ARU | AD7470BRU |
|---|---|---|---|---|---|
| Brand | Analog Devices | Analog Devices | Analog Devices | Analog Devices | Analog Devices |
| Package | TSSOP-24 | TSSOP-24 | TSSOP-24 | TSSOP-24 | TSSOP-24 |
| Resolution | 12 bit | 12 bit | 12 bit | 10 bit | 10 bit |
| Sampling Rate | 1.5 MSPS | 1.5 MSPS | 1.5 MSPS | 1.75 MSPS | 1.75 MSPS |
| Supply Voltage Range | 2.7 V to 5.25 V | 2.7 V to 5.25 V | 2.7 V to 5.25 V | 2.7 V to 5.25 V | 2.7 V to 5.25 V |
| ADC Architecture | Successive approximation | Successive approximation | Successive approximation | Successive approximation | Successive approximation |
| Number of Channels | 1 channel | 1 channel | 1 channel | 1 channel | 1 channel |
| Output Interface | Parallel | Parallel | Parallel | Parallel | Parallel |
| Temperature Grade | Y suffix ordering grade | A suffix ordering grade | B suffix ordering grade | A suffix ordering grade | B suffix ordering grade |
주요 차별점
- Higher conversion resolution within the same family (vs AD7470ARU)
- Same-footprint temperature-grade flexibility (vs AD7472BRU)
- Resolution prioritized over maximum throughput (vs AD7470BRU)
설계 노트
Route the analog input directly from the sensing or conditioning circuit to the AD7472YRU input pin, and keep the digital output traces away from that path. A continuous ground plane under the analog section helps establish a low-impedance return. Place supply-bypass and reference components close to their associated pins, following the layout and component values shown in the Analog Devices data sheet.
Capture each conversion using the conversion-complete timing and acquisition interval defined in the manufacturer data sheet. Because the AD7472YRU uses a parallel interface, the receiving FPGA or MCU must meet the setup and hold requirements at the indicated sampling edge. Avoid deriving an equivalent timing sequence solely from the 1.5 MSPS headline rate.
Do not treat an AD7470 device as an exact AD7472YRU replacement. The AD7470 family operates at up to 1.75 MSPS but provides only 10-bit resolution, whereas the AD7472 provides 12 bits at up to 1.5 MSPS. A substitution may also require firmware rescaling and verification of the full-scale code range before it is approved for production.
Design the analog and digital supplies around the 2.7 V to 5.25 V operating range. Bypass each supply connection at the device with the capacitance and placement recommended in the manufacturer data sheet, and keep switching-regulator loops and their high-current paths away from the analog input and reference network.
규정 준수 정보
The available product information identifies the AD7472 family as a low-power ADC but does not provide explicit RoHS, REACH, halogen-free, or conflict-minerals declarations. AEC-Q100 status is marked not applicable because the part is not identified as an automotive-qualified device.