ATSAMA5D27-SOM1-EK1 - SAMA5D27 ARM Cortex-A5 500MHz Eval Kit
부품 번호: ATSAMA5D27-SOM1-EK1 ✓ 활성| 수량 | 단가 | 합계 |
|---|---|---|
| 1 | $198.5 | $198.50 |
| 10 | $178.65 | $1,786.50 |
| 25 | $168.73 | $4,218.25 |
| 50 | $158.8 | $7,940.00 |
| 100 | $148.88 | $14,888.00 |
ATSAMA5D27-SOM1-EK1 개요
An evaluation kit (EK) is a printed-circuit-board hardware development platform that integrates the target SoC/SiP with power, memory, debug, and standard I/O headers so engineers can validate firmware and applications before designing a custom carrier. The ATSAMA5D27-SOM1-EK1 sits at the top of the SAMA5D2 evaluation hierarchy above discrete SAMA5D2 Xplained boards, providing the lowest-effort path to running embedded Linux on a Cortex-A5 with hardware-floating-point and rich connectivity.
Key features of the baseboard include an on-board debugger, multiple mikroBUS sockets, an LCD/touch connector, USB device and host ports, Ethernet (GMII/RGMII expansion), CAN, two SD card slots, JTAG/SWD, audio codec interface, and expansion headers that map nearly every SAMA5D2 signal to a 0.1-inch header. The integrated Power Management IC and secure-element footprints on the ATSAMA5D27-SOM1 module simplify power-tree design and security key storage for IoT edge nodes.
The SAMA5D27 SiP architecture pairs the Cortex-A5 core with a peripheral set including 12-bit ADC, hardware crypto accelerators (AES, SHA, TRNG), and a 24-bit peripheral-touch controller, allowing the same evaluation kit to be reused across HMI, connectivity gateway, and secure-credential prototypes. The DDR2 interface is fully validated at 500 MHz, removing the timing and signal-integrity work normally needed for production designs.
Typical applications include industrial HMI panels, smart-home gateways, edge IoT sensors with secure boot, Linux-based point-of-sale terminals, and connected-utility metering. Designers also reuse the kit as a low-volume ODM reference for products based on the ATSAMA5D27 SiP. A single design consideration dominates: when migrating to production, swap the kit's baseboard for a custom carrier that hosts the ATSAMA5D27-SOM1 module directly - the pinout is documented in the SOM1 datasheet.
This page synthesizes distributor pricing, drop-in alternatives, and practical design notes not found in the manufacturer datasheet.
드롭인 대체품: ATSAMA5D27-SOM1-EK1 — 동일 패키지, 핀 호환. PCB 재작업이 필요한 다른 패키지 부품은 제외됩니다.
이 시리즈의 변형
다음과 드롭인 호환되는 동일 시리즈 모델: ATSAMA5D27-SOM1-EK1 (동일 폼 팩터 및 풋프린트) — 차이점: Package, Mounting Type, Core Architecture, Operating Temperature, Backup Mode Current.
빠른 비교 도구 — 나란히 비교할 대체 부품을 선택하십시오:
ATSAMA5D27-SOM1
✅ 드롭인📋 참조 대체품 (카탈로그에 없음)
ATSAMA5D27C-D1G-CU
✅ 드롭인✓ 재고 있음
$19.1 / 개
데이터시트 보기 →ATSAMA5D27C-CUR
✅ 드롭인✓ 재고 있음
$12.9 / 개
데이터시트 보기 →ATSAMA5D27-WLSOM1-EK1
✅ 드롭인📋 참조 대체품 (카탈로그에 없음)
ATSAMA5D26C-CU
✅ 드롭인✓ 재고 있음
$11.8 / 개
데이터시트 보기 →ATSAMA5D24C-CUR
✅ 드롭인✓ 재고 있음
$10.2 / 개
데이터시트 보기 →ATSAMA5D27A-CU
✅ 드롭인✓ 재고 있음
$7.83 / 개
데이터시트 보기 →ATSAMA5D27-SOM1-EK1 사양 (제조사 공개)
| Product Type | Embedded Evaluation Board / Development Kit |
| Target Module | ATSAMA5D27-SOM1 |
| Embedded SiP | ATSAMA5D27C-D1G-CU (Cortex-A5 + 1-Gbit DDR2) |
| Processor Core | ARM Cortex-A5 |
| Maximum Core Frequency | 500 MHz |
| DDR2 SDRAM | 1 Gbit (128 MB) on SiP |
| NOR Flash | 64 Mbit |
| EEPROM | 1 Kbit |
| Operating System Support | Linux, RTOS (Buildroot, Yocto, mainline Linux) |
| Debug Interface | On-board debugger, JTAG/SWD headers |
| Connectivity | USB Host/Device, GMII/RGMII Ethernet expansion, CAN, SD/MMC x2, mikroBUS x2, Audio codec, LCD/touch connector |
| Expansion Headers | 0.1-inch headers mapping SAMA5D2 peripheral pins |
| Documentation | 60-page SAMA5D27 SOM1 Kit1 User's Guide |
| 실장 유형 | Through-hole / desktop development board |
| RoHS 상태 | Compliant |
ATSAMA5D27-SOM1-EK1 인터페이스 및 커넥터
ATSAMA5D27-SOM1-EK1은(는) 제조사에서 공개한 대로 다음 인터페이스와 커넥터를 제공합니다: GPIO. 확장 헤더 핀아웃, 커넥터 핀 번호, 전기적 한계는 제조사 문서에 정의되어 있습니다.
| GPIO | 0.1-inch headers mapping SAMA5D2 peripheral pins |
다음을 참조하십시오: 제조사 문서 전체 확장 헤더 핀아웃 및 커넥터 핀 번호는 다음을 참조하십시오.
일반적인 애플리케이션
ATSAMA5D27-SOM1-EK1 적합 용도: 6 애플리케이션s: Embedded Linux Prototyping, Industrial HMI Development, Smart Home Gateway Reference, Secure Edge IoT Node, Connected Utility Metering, Low-Volume ODM Reference Design.
Embedded Linux Prototyping
The ATSAMA5D27-SOM1-EK1 is the canonical Microchip platform for embedded Linux bring-up on the SAMA5D27 SiP. The on-board debugger, pre-validated 1-Gbit DDR2 interface, and 64-Mbit NOR Flash allow engineers to boot mainline Linux, Buildroot, or Yocto images in minutes without designing custom power, reset, or boot-memory circuits. The 500 MHz Cortex-A5 with hardware floating-point is fast enough to validate userspace applications, device drivers, and kernel subsystems before porting to a custom carrier. Compared with bare Xplained boards, the EK1 removes the DDR2 layout risk that dominates first-pass bring-up on Cortex-A designs.
추천
Industrial HMI Development
The ATSAMA5D27-SOM1-EK1 baseboard exposes an LCD/touch connector, audio codec interface, and multiple mikroBUS sockets that map directly to typical industrial-HMI architectures. The Cortex-A5 core runs LVGL, Qt, or WebKit-based GUI stacks comfortably, while the 1-Gbit DDR2 provides enough headroom for 800x480 and small 1080p framebuffers. The on-board peripherals let engineers prototype resistive and capacitive touch panels plus rotary encoders without spinning a custom PCB. Drop the production carrier around the ATSAMA5D27-SOM1 module and the same firmware ports unchanged.
추천
Smart Home Gateway Reference
With the ATSAMA5D27-SOM1-EK1's GMII/RGMII Ethernet expansion, dual CAN, USB host/device, and SD card slots, the kit doubles as a smart-home gateway reference. The SAMA5D27 SiP's hardware crypto accelerators (AES, SHA, TRNG) plus the module's secure-element footprint support secure boot and TLS at the edge. Linux-friendly networking stacks (iptables/nftables, OpenWRT) run on the Cortex-A5 at 500 MHz with margin for routing, MQTT brokering, and local automation. The EK1 is widely used to de-risk production gateways before the custom carrier is built.
추천
Secure Edge IoT Node
The ATSAMA5D27-SOM1-EK1 validates secure-boot flows and hardware-trusted execution on the SAMA5D27. The module's secure-element footprint and PMIC simplify power-tree and key-storage design for tamper-resistant IoT nodes. Engineers use the kit to prototype OTA update flows with signed images, hardware-bound keys, and TRNG-seeded session keys. Compared with discrete SAMA5D2 boards, the EK1 also exposes the on-board debugger for fast secure-state inspection.
추천
Connected Utility Metering
For utility metering prototypes, the ATSAMA5D27-SOM1-EK1 provides dual CAN (for in-vehicle or field-bus networks), Ethernet expansion, and a low-power profile that fits battery-assisted metering designs. The 24-bit peripheral-touch controller and 12-bit ADC on the SAMA5D27 SiP connect to metering front-ends without external DSP, and the secure boot path is suitable for metrology certification. The kit lets engineers validate the entire metering stack - acquisition, signed telemetry, and secure provisioning - on production-equivalent silicon.
추천
Low-Volume ODM Reference Design
Design houses use the ATSAMA5D27-SOM1-EK1 as the reference for low-volume ODM products built around the ATSAMA5D27-SOM1 module. The baseboard's expansion headers expose nearly every SAMA5D2 signal, which accelerates carrier-board schematic and layout reuse. After firmware is validated on the EK1, the production team spins a custom carrier that hosts the same SOM module, eliminating the DDR2 layout risk that normally dominates Cortex-A carrier design. This kit-to-SOM-to-product flow is the documented Microchip migration path for SAMA5D2 designs.
추천
추천 제품 요약
엔지니어링 참조 데이터: ATSAMA5D27-SOM1-EK1 — 비교, 설계 지침 및 규정 준수 정보.
선택 가이드
대체품과의 비교
| 파라미터 | 이 제품 | ATSAMA5D27-SOM1 | ATSAMA5D27C-D1G-CU | ATSAMA5D27C-CUR | ATSAMA5D27-WLSOM1-EK1 | ATSAMA5D26C-CU | ATSAMA5D24C-CUR | ATSAMA5D27A-CU |
|---|---|---|---|---|---|---|---|---|
| Brand | Microchip Technology | Microchip Technology | Microchip Technology | Microchip Technology | Microchip Technology | Microchip Technology | Microchip Technology | Microchip Technology |
| Package / Form Factor | SOM1 EK1 baseboard (with ATSAMA5D27-SOM1 module) | SOM1 module only (no baseboard) | TFBGA-289 SiP | TFBGA-289 SiP (tape & reel) | SOM1 EK1 baseboard with WLSOM1 module | TFBGA-289 SiP | TFBGA-289 SiP (tape & reel) | TFBGA-289 SiP |
| Processor Core | ARM Cortex-A5 500 MHz | ARM Cortex-A5 500 MHz | ARM Cortex-A5 500 MHz | ARM Cortex-A5 500 MHz | ARM Cortex-A5 500 MHz | ARM Cortex-A5 500 MHz | ARM Cortex-A5 500 MHz | ARM Cortex-A5 500 MHz |
| On-chip DDR2 SDRAM | 1 Gbit (128 MB) | 1 Gbit (128 MB) DDR2 | 1 Gbit (128 MB) DDR2 | 1 Gbit (128 MB) DDR2 | 2 Gbit (256 MB) LPDDR2 | 1 Gbit (128 MB) DDR2 | 1 Gbit (128 MB) DDR2 | 1 Gbit (128 MB) DDR2 |
| Wireless Connectivity | None (wired only) | None | None | None | Wi-Fi + Bluetooth integrated | None | None | None |
| On-board PMIC | Yes (on SOM1 module) | Yes | External required | External required | Yes (on WLSOM1 module) | External required | External required | External required |
| Linux Support | Mainline Linux, Buildroot, Yocto | Mainline Linux, Buildroot, Yocto | Mainline Linux, Buildroot, Yocto | Mainline Linux, Buildroot, Yocto | Mainline Linux, Buildroot, Yocto | Mainline Linux, Buildroot, Yocto | Mainline Linux, Buildroot, Yocto | Mainline Linux, Buildroot, Yocto |
| Use Case Focus | Wired HMI + Linux prototyping | Custom carrier prototyping | Bare-SiP integration | Bare-SiP integration (T&R) | Wireless IoT prototyping | Lower-cost HMI/gateway | Cost-optimized SAMA5D2 | Alternate silicon revision |
주요 차별점
- Integrated SOM module with validated DDR2 (vs ATSAMA5D27-WLSOM1-EK1)
- Same form factor, interchangeable with WLSOM1-EK1 (vs ATSAMA5D27-WLSOM1-EK1)
- Mainline Linux, Buildroot, Yocto support (vs ATSAMA5D24C-CUR)
설계 노트
Power the EK1 baseboard from a regulated 5 V DC barrel jack (center-positive, 2.1 mm). The on-board PMIC inside the ATSAMA5D27-SOM1 module then generates all SAMA5D27 SiP and DDR2 rails. Estimated: at 500 MHz core with Ethernet and LCD active, total board power is approximately 4-5 W, so a 5 V/2 A supply provides comfortable margin. Do not back-feed 3.3 V from external sources; the PMIC's sequencing is required for clean DDR2 bring-up and safe boot.
When porting the EK1 design to a custom carrier, place the ATSAMA5D27-SOM1 module socket (or solder footprint) over a continuous ground plane and route the 1-Gbit DDR2 signals with 50 ohm controlled impedance and length matching per the SAMA5D27 datasheet. Estimated: keep DDR2 traces under 50 mm to maintain signal integrity. Add a 4-layer stack-up with dedicated ground and power planes; the EK1 reference layout is the recommended starting point.
Do not boot the SAMA5D27 SiP from 1.8 V microSD cards without re-validating the boot mode straps; the EK1 default uses an SD card boot image with specific pull-ups. Also, when migrating firmware from the EK1 to a bare ATSAMA5D27C-D1G-CU design, ensure the external PMIC is sequenced exactly like the SOM1 module's on-board PMIC - DDR2 training fails if the supply ramp timing is off by more than a few milliseconds.
The GMII/RGMII Ethernet expansion header on the EK1 is not impedance-controlled by default; use short flying leads (under 25 mm) to the PHY or, for production, replicate the EK1's reference stack-up. Estimated: RGMII edges have ~2 ns setup/hold budget, so any extra stub from the expansion header can cause CRC errors. Keep the optional 125 MHz clock trace short and matched within 25 mil.
규정 준수 정보
RoHS and REACH compliance confirmed on Microchip product page and DigiKey listing. AEC-Q100 not applicable - this is a development kit, not a production SiP. Conflict-minerals compliance per Microchip statement.