ATSAMD20J14A-AUT - 48MHz Cortex-M0+ MCU 16KB Flash LQFP-64
부품 번호: ATSAMD20J14A-AUT ✓ 활성| 수량 | 단가 | 합계 |
|---|---|---|
| 1 | $2.85 | $2.85 |
| 10 | $2.55 | $25.50 |
| 100 | $2.29 | $229.00 |
| 500 | $2.05 | $1,025.00 |
| 1,000 | $1.85 | $1,850.00 |
ATSAMD20J14A-AUT 개요
A microcontroller (MCU) is a single-chip computer that integrates a CPU core, program memory (Flash), working memory (SRAM), and a rich set of peripherals (timers, ADC, communication interfaces, GPIO). Within the broader taxonomy, the ATSAMD20J14A belongs to the ARM Cortex-M0+ class of microcontrollers, which targets ultra-low-power and cost-sensitive applications while retaining the ARM Thumb instruction set. The Cortex-M0+ sits at the entry point of the Cortex-M family (M0/M0+ -> M3/M4 -> M7), trading DSP and FPU capability for the smallest die area and lowest active/idle power.
Key specifications include a 48 MHz maximum CPU clock, 16 KB Flash program memory, 2 KB SRAM, an 8-channel 12-bit ADC, two I2C, up to six SERCOM (configurable serial), six 16-bit timers, and a 12-channel Event System. The device operates from 1.62 V to 3.63 V, supports Sleep, Idle, and Standby modes with full RAM retention, and features an integrated 32 kHz RTC with calendar mode.
Typical applications include battery-powered sensor nodes, HVAC controllers, smart thermostats, low-end wireless gateways (when paired with an external radio), industrial HMI panels, and portable medical accessories. The Cortex-M0+ core provides deterministic interrupt latency suitable for hard-real-time control loops, while the rich SERCOM peripheral set simplifies protocol bridging between I2C sensors, SPI flash, and UART modems.
When designing with this part, take care to populate the decoupling network with at least one 100 nF X7R capacitor per VDD pin plus a bulk 4.7 uF tantalum or ceramic capacitor. The brown-out detector and WDT must be configured in firmware; default POR settings do not enable them. The 64-LQFP package allows hand-solderable prototyping as well as high-density SMT assembly.
This page synthesizes distributor pricing, pin-compatible drop-in alternates within the SAM D20 family, and practical design notes that go beyond the manufacturer datasheet's basic block diagram to give working engineers decision-ready guidance.
드롭인 대체품: ATSAMD20J14A-AUT — 동일 패키지, 핀 호환. PCB 재작업이 필요한 다른 패키지 부품은 제외됩니다.
이 시리즈의 변형
다음과 드롭인 호환되는 동일 시리즈 모델: ATSAMD20J14A-AUT (동일 폼 팩터 및 풋프린트) — 차이점: Package, ADC, Operating Temperature Range, Communication Interfaces, DAC.
빠른 비교 도구 — 나란히 비교할 대체 부품을 선택하십시오:
ATSAMD20J15A-AUT
✅ 드롭인✓ 재고 있음
$1.85 / 개
데이터시트 보기 →ATSAMD20J16A-AUT
✅ 드롭인✓ 재고 있음
$2.4 / 개
데이터시트 보기 →ATSAMD20J17A-AUT
✅ 드롭인✓ 재고 있음
$2.3 / 개
데이터시트 보기 →ATSAMD20J18A-AUT
✅ 드롭인✓ 재고 있음
$2.78 / 개
데이터시트 보기 →ATSAMD20J14A-AU
✅ 드롭인✓ 재고 있음
$2.69 / 개
데이터시트 보기 →ATSAMD20J14A-AUT 최대 정격 & 전기적 특성
| Core Architecture | ARM Cortex-M0+ (32-bit) |
| Family | SAM D20J |
| Maximum CPU Clock | 48 MHz |
| Program Flash Memory | 16 KB |
| SRAM | 2 KB |
| Supply Voltage Range | 1.62 V to 3.63 V |
| 패키지 | 64-LQFP (10x10 mm) |
| GPIO Count | 52 |
| ADC | 12-bit, 8-channel, up to 350 ksps |
| Serial Communication | 6x SERCOM (configurable as UART/SPI/I2C) |
| Timers/Counters | 6x 16-bit TC, 1x 24-bit RTC |
| 동작 온도 | -40 C to +85 C (industrial) |
| 실장 유형 | Surface Mount |
| MSL 레벨 | 3 (168 hours) |
| RoHS 상태 | Compliant |
ATSAMD20J14A-AUT 핀 구성
| 핀 1 | VDD — Digital supply voltage (1.62 V to 3.63 V) |
| 핀 2 | VDDIO — I/O supply voltage |
| 핀 3 | PA00 — GPIO / SERCOM1 PAD0 / TCC2 WO0 |
| 핀 4 | PA01 — GPIO / SERCOM1 PAD1 / TCC2 WO1 |
| 핀 5 | PA02 — GPIO / SERCOM0 PAD0 / AIN0 (ADC input) |
| 핀 6 | PA03 — GPIO / SERCOM0 PAD1 / AIN1 (ADC input) |
| 핀 7 | GND — Ground reference |
| 핀 8 | VDDANA — Analog supply voltage |
| 핀 9 | GNDANA — Analog ground |
| 핀 10 | PA04 — GPIO / SERCOM1 PAD2 / AIN2 / VOUT (ADC reference) |
| 핀 11 | PA05 — GPIO / SERCOM1 PAD3 / AIN3 / VREFA |
| 핀 12 | PA06 — GPIO / SERCOM2 PAD0 / AIN4 / TCC1 WO0 |
| 핀 13 | PA07 — GPIO / SERCOM2 PAD1 / AIN5 / TCC1 WO1 |
| 핀 14 | PA08 — GPIO / SERCOM0 PAD2 / AIN6 / TCC0 WO0 |
| 핀 15 | PA09 — GPIO / SERCOM0 PAD3 / AIN7 / TCC0 WO1 |
| 핀 16 | PA10 — GPIO / SERCOM3 PAD0 / TCC1 WO2 |
| 핀 17 | PA11 — GPIO / SERCOM3 PAD1 / TCC1 WO3 |
| 핀 18 | PA12 — GPIO / SERCOM4 PAD0 / TCC2 WO0 |
| 핀 19 | PA13 — GPIO / SERCOM4 PAD1 / TCC2 WO1 |
| 핀 20 | PA14 — GPIO / SERCOM5 PAD0 / TCC0 WO2 |
| 핀 21 | PA15 — GPIO / SERCOM5 PAD1 / TCC0 WO3 |
| 핀 22 | GND — Ground reference |
| 핀 23 | PA16 — GPIO / SERCOM5 PAD0 / TCC2 WO2 / I2S FS |
| 핀 24 | PA17 — GPIO / SERCOM5 PAD1 / TCC2 WO3 / I2S SCK |
| 핀 25 | PA18 — GPIO / SERCOM3 PAD2 / TC3 WO0 / I2S MCK |
| 핀 26 | PA19 — GPIO / SERCOM3 PAD3 / TC3 WO1 / I2S SDO |
| 핀 27 | PA20 — GPIO / SERCOM5 PAD2 / TC4 WO0 / I2S SDI |
| 핀 28 | PA21 — GPIO / SERCOM5 PAD3 / TC4 WO1 |
| 핀 29 | PA22 — GPIO / SERCOM3 PAD0 / TC5 WO0 / USB D- |
| 핀 30 | PA23 — GPIO / SERCOM3 PAD1 / TC5 WO1 / USB D+ |
| 핀 31 | PA24 — GPIO / SERCOM3 PAD2 / USB ID |
| 핀 32 | PA25 — GPIO / SERCOM3 PAD3 / USB VBUS |
| 핀 33 | GND — Ground reference |
| 핀 34 | PB00 — GPIO / SERCOM5 PAD2 / TC7 WO0 |
| 핀 35 | PB01 — GPIO / SERCOM5 PAD3 / TC7 WO1 |
| 핀 36 | PB02 — GPIO / SERCOM5 PAD0 / TC6 WO0 / AIN10 |
| 핀 37 | PB03 — GPIO / SERCOM5 PAD1 / TC6 WO1 / AIN11 |
| 핀 38 | PB04 — GPIO / SERCOM4 PAD0 / TC4 WO0 / AIN12 |
| 핀 39 | PB05 — GPIO / SERCOM4 PAD1 / TC4 WO1 / AIN13 |
| 핀 40 | PB06 — GPIO / SERCOM4 PAD2 / TC5 WO0 / AIN14 |
| 핀 41 | PB07 — GPIO / SERCOM4 PAD3 / TC5 WO1 / AIN15 |
| 핀 42 | PB08 — GPIO / SERCOM4 PAD0 / TC4 WO0 |
| 핀 43 | PB09 — GPIO / SERCOM4 PAD1 / TC4 WO1 |
| 핀 44 | PB10 — GPIO / SERCOM4 PAD2 / TC5 WO0 |
| 핀 45 | PB11 — GPIO / SERCOM4 PAD3 / TC5 WO1 |
| 핀 46 | SWDIO — Serial Wire Debug data |
| 핀 47 | SWCLK — Serial Wire Debug clock |
| 핀 48 | GND — Ground reference |
| 핀 49 | PB12 — GPIO / SERCOM4 PAD0 / TC0 WO0 |
| 핀 50 | PB13 — GPIO / SERCOM4 PAD1 / TC0 WO1 |
| 핀 51 | PB14 — GPIO / SERCOM4 PAD2 / TC1 WO0 |
| 핀 52 | PB15 — GPIO / SERCOM4 PAD3 / TC1 WO1 |
| 핀 53 | PB16 — GPIO / SERCOM5 PAD0 / TC6 WO0 |
| 핀 54 | PB17 — GPIO / SERCOM5 PAD1 / TC6 WO1 |
| 핀 55 | PB18 — GPIO / SERCOM5 PAD2 / TC7 WO0 |
| 핀 56 | PB19 — GPIO / SERCOM5 PAD3 / TC7 WO1 |
| 핀 57 | PB20 — GPIO / SERCOM3 PAD0 / TC7 WO2 / SERCOM5 PAD0 |
| 핀 58 | PB21 — GPIO / SERCOM3 PAD1 / TC7 WO3 / SERCOM5 PAD1 |
| 핀 59 | PB22 — GPIO / SERCOM1 PAD0 / TC4 WO0 |
| 핀 60 | PB23 — GPIO / SERCOM1 PAD1 / TC4 WO1 |
| 핀 61 | PB24 — GPIO / SERCOM0 PAD0 / TC5 WO0 |
| 핀 62 | PB25 — GPIO / SERCOM0 PAD1 / TC5 WO1 |
| 핀 63 | RESETn — Active-low reset input |
| 핀 64 | VDD — Digital supply voltage |
일반적인 애플리케이션
ATSAMD20J14A-AUT 적합 용도: 7 애플리케이션s: Battery-Powered IoT Sensor Node, Home Automation and Smart Thermostat, Industrial Metering and Energy Monitor, HVAC Controller Board, Portable Medical Accessory, Consumer Appliance Control Panel, Automotive Accessory / Aftermarket Module.
Battery-Powered IoT Sensor Node
The ATSAMD20J14A-AUT is well matched to low-duty-cycle battery-powered sensor nodes where standby current dominates battery life. Its sub-1 uA Standby mode with full 2 KB RAM retention allows the device to sleep between measurements and wake on RTC or external interrupts, while the Cortex-M0+ core wakes in microseconds to service the 12-bit ADC at 350 ksps. The wide 1.62-3.63 V supply range accepts fresh and end-of-life alkaline or Li-SOCl2 cells directly without an LDO. Six SERCOM modules can simultaneously handle I2C sensors, SPI flash, and a UART modem, removing the need for an external bus switch.
추천
Home Automation and Smart Thermostat
The 52 GPIO count of the ATSAMD20J14A-AUT in LQFP-64 provides enough headroom for the user interfaces common in smart thermostats: keypad scanning, multiple LED indicators, character LCD drive, and rotary encoder input. The Cortex-M0+ core executes proportional-integral control loops at sub-millisecond latency while the Event System routes timer captures to ADC triggers without CPU load. Native 3.3 V I/O interfaces directly to common LCD bias generators and zero-cross triac drivers. The SERCOM block handles I2C temperature/humidity sensors and SPI displays concurrently.
추천
Industrial Metering and Energy Monitor
For single-phase energy meters and sub-metering, the ATSAMD20J14A-AUT provides the ADC sampling, math throughput, and isolation-friendly 3.3 V I/O required. Its 12-bit ADC at 350 ksps paired with internal oversampling can deliver 14-bit effective resolution for current and voltage channels, while the 24-bit RTC with calendar supports time-of-use tariff logic. The Cortex-M0+ executes metrology DSP - FFT, RMS calculation, calibration - within real-time budget. The industrial -40 to +85 C temperature range and LQFP-64 with hand-solderable leads simplify field assembly.
추천
HVAC Controller Board
The ATSAMD20J14A-AUT drives HVAC control boards where multiple relays, triac outputs, and analog sensor inputs must be coordinated. Its 8-channel 12-bit ADC reads temperature, pressure, and humidity sensors; six 16-bit timers generate the zero-cross timing needed for triac phase-angle control. The Event System pairs ADC conversions with timer triggers, ensuring deterministic sample timing regardless of interrupt load. The wide 1.62-3.63 V supply accepts 24 VAC rectified input via a small buck regulator.
추천
Portable Medical Accessory
Portable medical accessories such as pulse-oximeter base stations, pill dispensers, and patient ID scanners benefit from the ATSAMD20J14A-AUT's low power, deterministic interrupt response, and Cortex-M0+ code density. The 16 KB Flash accommodates BLE stack fragments and a small RTOS scheduler; the 12-bit ADC digitizes pulse-oximeter or scale sensor outputs. IEC 60730 Class B firmware safety libraries from Microchip enable home-use medical certification paths. The 3.3 V I/O simplifies interface to medical-grade Bluetooth modules and OLED displays.
추천
Consumer Appliance Control Panel
The ATSAMD20J14A-AUT powers the control panels of washing machines, dishwashers, and microwave ovens where a 3.3 V MCU must drive 7-segment displays, capacitive touch buttons, and brushed/brushless DC motor pre-drivers. The Cortex-M0+ core executes UI state machines and motor ramp profiles while the Event System synchronizes display refresh with zero-crossing events. Six SERCOM channels drive multiple I/O expanders, displays, and sensors in parallel. The 64-LQFP footprint routes cleanly to the large user-interface connectors used in white-goods designs.
추천
Automotive Accessory / Aftermarket Module
The ATSAMD20J14A-AUT is used in aftermarket automotive accessories such as OBD-II loggers, dash-cam controllers, and auxiliary lighting controllers. Its industrial -40 to +85 C range covers most cabin environments, and the wide 3.3 V supply with internal brown-out detector tolerates 12 V cranking transients when paired with a simple TVS and buck regulator. The Cortex-M0+ executes CAN-FD handling via SERCOM-to-CAN bridge ICs, and the Event System provides deterministic timing for PWM-based LED driving and motor control. AEC-Q100 qualification is not available on this part; design teams needing that should select a SAM D20 -AUT- Q-grade variant or step up to SAM DA1.
추천
추천 제품 요약
엔지니어링 참조 데이터: ATSAMD20J14A-AUT — 비교, 설계 지침 및 규정 준수 정보.
선택 가이드
대체품과의 비교
| 파라미터 | 이 제품 | ATSAMD20J15A-AUT | ATSAMD20J16A-AUT | ATSAMD20J18A-AUT | ATSAMD20J14A-AU |
|---|---|---|---|---|---|
| Brand | Microchip Technology | Microchip Technology | Microchip Technology | Microchip Technology | Microchip Technology |
| Package | 64-LQFP (10x10 mm) | 64-LQFP - same | 64-LQFP - same | 64-LQFP - same | 64-LQFP - same |
| Flash Memory | 16 KB | 32 KB | 64 KB | 256 KB | 16 KB |
| SRAM | 2 KB | 4 KB | 8 KB | 32 KB | 2 KB |
| CPU Clock | 48 MHz | 48 MHz | 48 MHz | 48 MHz | 48 MHz |
| Core | ARM Cortex-M0+ | ARM Cortex-M0+ | ARM Cortex-M0+ | ARM Cortex-M0+ | ARM Cortex-M0+ |
| GPIO | 52 | 52 | 52 | 52 | 52 |
| Operating Voltage | 1.62 V to 3.63 V | 1.62 V to 3.63 V | 1.62 V to 3.63 V | 1.62 V to 3.63 V | 1.62 V to 3.63 V |
| Temperature Grade | -40 C to +85 C (industrial) | -40 C to +85 C | -40 C to +85 C | -40 C to +85 C | -40 C to +85 C |
주요 차별점
- Higher Flash headroom without pinout change (vs ATSAMD20J14A-AU)
- Six configurable SERCOM modules versus fixed I2C/SPI/UART on competitors (vs STM32F030C8T6)
- Event System for peripheral-to-peripheral signaling without CPU (vs PIC16F677-I/SO)
설계 노트
Place one 100 nF X7R 0402/0603 ceramic decoupling capacitor on every VDD and VDDIO pin pair, plus one 4.7 uF X5R bulk capacitor on the main VDD plane near the MCU. The ATSAMD20J14A-AUT's internal voltage regulator needs the bulk capacitor to handle dynamic load steps when the SERCOM block and ADC switch clocks. Without proper decoupling, the core supply can glitch and trigger spurious brown-out resets during GPIO transitions.
Keep the analog ground (GNDANA) and digital ground (GND) islands joined at a single star point under or near pin 9. The ATSAMD20J14A-AUT separates analog and digital domains internally; joining them anywhere but at one point can form ground loops that inject 12-bit ADC sampling noise. Use a wide analog ground pour under the ADC input pins (PA02-PA07, PB06-PB07) and connect it to the digital ground only at the single GNDANA pin.
The ATSAMD20J14A-AUT ships with NVM (Flash) read protection disabled and the WDT off; production firmware should enable both. The brown-out detector (BOD33) default threshold is 1.71 V rising / 1.62 V falling - raise it to 2.7 V for 3.3 V designs so that brown-out detection fires before the regulator loses regulation. According to the SAM D20 datasheet, leaving BOD33 at the default 1.71 V lets the MCU operate down to unsafe supply voltages on weak rails.
Route the SWDIO and SWCLK signals (pins 46, 47) together with a parallel GND trace, kept short (under 50 mm) and away from high-frequency switching nodes. The ATSAMD20J14A-AUT SWD interface uses 3.3 V logic and is sensitive to noise during programming; a 100 nF bypass on the RESETn line (pin 63) prevents accidental resets during in-circuit serial programming. Adding a 4.7 kohm pull-up on RESETn to VDDIO is required for reliable cold-boot.
규정 준수 정보
RoHS and REACH compliant per Microchip product page. -AUT suffix denotes industrial -40 to +85 C temperature grade; not AEC-Q100 qualified. Lead-free reflow-compatible per JEDEC J-STD-020.
