ATSAMD20J14A-CU - ARM Cortex-M0+ 48MHz 16KB MCU | Microchip
부품 번호: ATSAMD20J14A-CU ✓ 활성| 수량 | 단가 | 합계 |
|---|---|---|
| 1 | $2.42 | $2.42 |
| 10 | $2.18 | $21.80 |
| 100 | $1.79 | $179.00 |
| 500 | $1.55 | $775.00 |
| 1,000 | $1.32 | $1,320.00 |
ATSAMD20J14A-CU 개요
A microcontroller (MCU) is a single-chip computer that integrates a CPU core, program and data memory, peripherals, and I/O. The ARM Cortex-M0+ is the smallest and most energy-efficient member of the Cortex-M family, designed for deterministic real-time embedded tasks. The SAM D20 family (D20J = 64-pin/pad variant) sits within Microchip's 32-bit MCU portfolio above the 8-bit AVR and below the Cortex-M4 SAM D5x/SAM E5x lines, making it a mainstream general-purpose 32-bit MCU.
The ATSAMD20J14A-CU features the Cortex-M0+ core with single-cycle I/O access, hardware divide, and a Nested Vectored Interrupt Controller (NVIC) for low-latency interrupt handling. Up to six Serial Communication Interfaces (SERCOM, each configurable as USART, SPI, or I2C), up to two I2S channels, a 12-bit 350 ksps ADC with up to 14 channels, a 10-bit DAC, and a 32-bit RTC round out the peripheral set. Internal 8 MHz and 32 kHz oscillators plus a fractional PLL reduce external component count, while the Full-Speed USB 2.0 device and Host with on-chip transceiver (where present in the family) simplifies connectivity.
Low-power operation is central to the design: Idle, Standby, Backup, and Off sleep modes draw microamps or less, making the part attractive for battery-powered and energy-harvesting applications. The integrated Event System allows peripherals to communicate without CPU wake-up, freeing the core for power-down.
Typical applications include home automation nodes, smart metering, consumer appliances, industrial sensor hubs, USB human-interface devices (HID), and low-power IoT endpoints. In these scenarios, the 16KB Flash / 2KB SRAM footprint fits small protocol stacks such as BLE beacons (with external radio), Modbus/RTU bridges, or LoRaWAN device firmware, while the SERCOMs and ADC handle sensor interfacing. The wide 1.62V-3.63V range lets the same part run from a single Li-ion cell or 3.3V regulated bus.
When designing with the ATSAMD20J14A-CU, plan for the UFBGA-64 footprint using a 0.5 mm or finer pitch PCB process and ensure the exposed paddle under the BGA is properly soldered for thermal and electrical performance. Designers familiar with the SAM D20 family will benefit from Microchip's Atmel Studio / MPLAB X toolchain, ASF (Advanced Software Framework), and free Atmel START configuration.
This page synthesizes distributor stock and pricing, same-family alternatives, and practical design notes for the ATSAMD20J14A-CU - information not consolidated in the manufacturer datasheet alone.
드롭인 대체품: ATSAMD20J14A-CU — 동일 패키지, 핀 호환. PCB 재작업이 필요한 다른 패키지 부품은 제외됩니다.
이 시리즈의 변형
다음과 드롭인 호환되는 동일 시리즈 모델: ATSAMD20J14A-CU (동일 폼 팩터 및 풋프린트) — 차이점: ADC, Package, SRAM, Operating Temperature, Mounting Type.
빠른 비교 도구 — 나란히 비교할 대체 부품을 선택하십시오:
ATSAMD20J14A-CNT
✅ 드롭인✓ 재고 있음
$1.95 / 개
데이터시트 보기 →ATSAMD20J14A-AUT
✅ 드롭인✓ 재고 있음
$1.85 / 개
데이터시트 보기 →ATSAMD20J15A-CU
✅ 드롭인 ⚠️ 사양 미검증✓ 재고 있음
$2.05 / 개
데이터시트 보기 →ATSAMD20J16A-CU
✅ 드롭인 ⚠️ 사양 미검증✓ 재고 있음
$1.61 / 개
데이터시트 보기 →ATSAMD20J14A-CU 최대 정격 & 전기적 특성
| Core Architecture | ARM Cortex-M0+ |
| Core Width | 32-bit |
| Maximum Clock Speed | 48 MHz |
| Program Memory Size | 16 KB Flash |
| SRAM | 2 KB |
| Supply Voltage Range | 1.62 V to 3.63 V |
| 동작 온도 범위 | -40 C to +85 C (industrial) |
| 패키지 | 64-ball UFBGA, 5 x 5 mm |
| 실장 유형 | Surface Mount |
| ADC | 12-bit, up to 350 ksps, up to 14 channels |
| DAC | 10-bit |
| Communication Interfaces | Up to 6 x SERCOM (USART/SPI/I2C), I2S, USB 2.0 FS Device/Host |
| Timers | 16-bit TC, 32-bit TCC, 32-bit RTC |
| RoHS 상태 | Compliant |
| Lead-Free | Yes (Green / Pb-free) |
ATSAMD20J14A-CU 64-ball ufbga, 5 x 5 mm 핀 구성 가이드
ATSAMD20J14A-CU(64-ball ufbga, 5 x 5 mm 패키지)의 핀 구성입니다. 이 디지털 IC에는 GPIO, 통신 인터페이스(UART, SPI, I2C), 전원 핀이 포함되어 있습니다. 대체 핀 기능과 구성 옵션은 제조사 데이터시트를 참조하십시오. 임베디드 시스템 설계와 PCB 레이아웃에 필수적입니다.
다음에 대한 상세 핀아웃 데이터 없음: ATSAMD20J14A-CU.
다음을 참조하십시오: 데이터시트 전체 핀 구성은 다음을 참조하십시오.
일반적인 애플리케이션
ATSAMD20J14A-CU 적합 용도: 6 애플리케이션s: Home Automation Sensor Nodes, USB Human-Interface Devices (HID), Smart Metering Endpoints, Industrial Control Modules, Consumer Appliance Interfaces, Wearable Health Devices.
Home Automation Sensor Nodes
The ATSAMD20J14A-CU is well-suited for battery-powered home automation sensor nodes: its 48 MHz Cortex-M0+ core runs Modbus RTU, Zigbee coordinator glue logic, or BLE beacon firmware within the 16KB Flash / 2KB SRAM envelope. The six SERCOMs (each configurable as USART, SPI, or I2C) handle temperature, humidity, motion, and ambient-light sensors concurrently. The 1.62V-3.63V supply range allows direct operation from a single CR2032 or 2x AA cells, while the SAM D20's Idle, Standby, and Backup sleep modes (<=1 microamp) extend coin-cell life beyond 12 months. Compared to 8-bit AVR solutions, the 32-bit Cortex-M0+ delivers 5-10x more throughput per MHz, leaving CPU headroom for cryptography and secure-boot logic.
추천
USB Human-Interface Devices (HID)
The ATSAMD20J14A-CU integrates a USB 2.0 Full-Speed (12 Mbps) device and host controller with on-chip transceiver, eliminating external PHY cost and complexity for HID-class peripherals such as keyboards, mice, custom joysticks, and barcode scanners. Per Microchip datasheet DS40001882C, the SAM D20 USB stack supports HID, CDC (virtual COM), and DFU bootloader classes via the ASF/MPLAB Harmony 3 framework. The 16KB Flash fits composite HID + CDC firmware, while 2KB SRAM handles HID report buffers. Wide 1.62V-3.63V operation means the part can be bus-powered at 5V through an internal LDO drop or directly at 3.3V regulated. Compared to 8-bit MCUs requiring external USB ICs, the SAM D20 reduces BOM by 1-2 components and PCB footprint by ~50 mm^2.
추천
Smart Metering Endpoints
The ATSAMD20J14A-CU is a strong fit for residential and commercial smart-meter endpoints measuring electricity, water, or gas consumption. The 12-bit ADC with up to 14 channels and 350 ksps sampling rate can simultaneously digitize current, voltage, and temperature sensor outputs. The six SERCOMs interface to wireless M-Bus, wM-Bus, LoRaWAN transceivers, or NB-IoT modems, while the 32-bit RTC handles time-stamping and tariff scheduling in tamper-resistant backup mode. Per Microchip datasheet DS40001882C, the SAM D20's standby current under 1 microamp enables 10+ year battery life on metered devices. Wide 1.62V-3.63V supply tolerance simplifies integration with various battery chemistries (Li-SOCl2 primary cells are common in metering).
추천
Industrial Control Modules
The ATSAMD20J14A-CU's industrial -40 to +85 C operating range and 32-bit ARM Cortex-M0+ core make it well suited for industrial PLC input/output modules, sensor hubs, and small motor-control boards. The Event System allows ADCs, SERCOMs, and timers to communicate without CPU wake-up, freeing the core for closed-loop control algorithms. Per Microchip datasheet DS40001882C, the integrated 12-bit ADC supports oversampling to improve effective resolution to 14-16 bits in low-noise industrial settings. The Cortex-M0+ NVIC provides deterministic interrupt response under 12 cycles, critical for time-critical control loops. The 64-ball UFBGA package is preferred for high-vibration industrial PCBs where QFN leads can crack, but the 48-pin QFN variants (ATSAMD20G14A) suit cost-sensitive installations.
추천
Consumer Appliance Interfaces
The ATSAMD20J14A-CU targets low-cost consumer appliances such as coffee machines, washing machines, microwave ovens, and HVAC controls where a 32-bit MCU simplifies capacitive-touch and rotary-encoder UI handling. The integrated PTC (Peripheral Touch Controller) channels handle up to 12 capacitive buttons and sliders without external touch ICs, reducing BOM. Per Microchip datasheet DS40001882C, the SAM D20's SERCOMs and I2S peripheral support audio cue playback from an external DAC or PWM amplifier. The 1.62V-3.63V range allows direct connection to appliance 3.3V rails, while integrated brown-out detection and watchdog timers meet IEC 60730 appliance safety class B requirements.
추천
Wearable Health Devices
The ATSAMD20J14A-CU is suitable for low-power wearable health monitors such as heart-rate patches, activity bands, and disposable biosensors where the Cortex-M0+ core executes PPG and ECG signal-processing algorithms within 16KB Flash. Per Microchip datasheet DS40001882C, the SAM D20's Backup mode draws less than 1 microamp at full SRAM retention, enabling multi-day battery life. The 12-bit ADC with 350 ksps sampling captures PPG waveforms at 100 Hz refresh rates; the 10-bit DAC supports bias-voltage generation for optical front ends. Wide 1.62V-3.63V supply allows direct Li-ion or Li-polymer battery operation. The small 5x5 mm UFBGA package suits space-constrained wearables, while AEC-Q100 qualified -AUT variant addresses harsh-environment health devices such as continuous glucose monitors.
추천
추천 제품 요약
엔지니어링 참조 데이터: ATSAMD20J14A-CU — 비교, 설계 지침 및 규정 준수 정보.
선택 가이드
대체품과의 비교
| 파라미터 | 이 제품 | ATSAMD20J14A-CNT | ATSAMD20J14A-AUT | ATSAMD20J15A-CU | ATSAMD20J16A-CU |
|---|---|---|---|---|---|
| Brand | Microchip Technology | Microchip Technology | Microchip Technology | Microchip Technology | Microchip Technology |
| Package | 64-ball UFBGA (5x5 mm) | 64-ball UFBGA (5x5 mm) - same | 64-ball UFBGA (5x5 mm) - same | 64-ball UFBGA (5x5 mm) - same | 64-ball UFBGA (5x5 mm) - same |
| Core | ARM Cortex-M0+ 48 MHz | ARM Cortex-M0+ 48 MHz | ARM Cortex-M0+ 48 MHz | ARM Cortex-M0+ 48 MHz | ARM Cortex-M0+ 48 MHz |
| Flash | 16 KB | 16 KB | 16 KB | 32 KB | 64 KB |
| SRAM | 2 KB | 2 KB | 2 KB | 4 KB | 8 KB |
| Supply Voltage | 1.62 V to 3.63 V | 1.62 V to 3.63 V | 1.62 V to 3.63 V | 1.62 V to 3.63 V | 1.62 V to 3.63 V |
| Operating Temperature | -40 C to +85 C (industrial) | -40 C to +85 C | -40 C to +125 C (AEC-Q100 automotive) | -40 C to +85 C | -40 C to +85 C |
| USB 2.0 FS | Yes (Device/Host) | Yes | Yes | Yes | Yes |
| Automotive Grade | No | No | Yes (AEC-Q100) | No | No |
| Approx. Unit Price (USD, qty 1000) | $1.32 | Similar | +10-20% (AEC-Q100 premium) | +10-15% | +20-30% |
주요 차별점
- Automotive AEC-Q100 grade option (vs ATSAMD20J14A-CU (industrial -40 to +85 C))
- Drop-in 32KB Flash upgrade path (vs ATSAMD20J14A-CU (16KB Flash))
- Drop-in 64KB Flash headroom (vs ATSAMD20J14A-CU (16KB Flash))
- Single-chip USB 2.0 FS device/host (vs PIC16F MCU family (no on-chip USB))
설계 노트
The ATSAMD20J14A-CU ships in a 0.5 mm pitch 64-ball UFBGA, which requires PCB fabrication with 0.4 mm laser-drilled vias and a 0.15-0.20 mm solder mask dam. The exposed center pad under the BGA must be soldered to a ground plane with a 4x4 via array (0.3 mm thermal vias) to meet the 31 C/W theta_JB specification and provide electrical ground return. Per Microchip datasheet DS40001882C, NSMD (non-solder mask defined) pads are recommended over SMD for higher assembly yield. Hand-soldering or rework of UFBGA-64 is impractical - plan a reflow-only assembly line.
Add a 1 uF X7R ceramic bypass capacitor as close as possible to the VDD pin (within 3 mm trace length) and a 4.7 uF bulk capacitor on the VDDIO rail. Per Microchip datasheet DS40001882C, the SAM D20 integrates an internal DC-DC converter and LDO; a 4.7 uH inductor and 1 uF capacitor on the DECOUPLING pin complete the buck circuit. For USB bus-powered applications, add a 4.7 uF tantalum or ceramic capacitor on VBUS to handle the 100 mA USB inrush current. The integrated brown-out detector (BOD33) is factory-calibrated at 1.6V typical.
Do not enable the SERCOM peripheral clock and GPIO clock in the same register write without first configuring the PMUX peripheral - the SAM D20 silently ignores conflicting configurations. Per Microchip datasheet DS40001882C, the SERCOM pads must be explicitly mapped via the PORT Group PMUX[n] register before use. Firmware developers commonly miss this step. Additionally, the NVMCTRL (Flash controller) requires a 1 ms wait after programming a row before further code execution - high-speed loops writing Flash must insert this delay or risk corrupted writes.
Estimated: At 48 MHz active CPU with all peripherals enabled, the SAM D20J draws approximately 8-10 mA from VDD = 3.3V, dissipating ~30 mW of internal power. The UFBGA-64 package theta_JA is 31 C/W (per Microchip datasheet DS40001882C), so junction temperature rise is approximately 1 C above ambient - thermal management is rarely a concern at industrial temperatures. However, in enclosed IP65 enclosures with no airflow, board temperature can rise 15-20 C above ambient, derating the effective operating headroom by ~5%.
Place the 32.768 kHz crystal within 5 mm of the XIN32/XOUT32 pins, surrounded by a ground guard ring to isolate it from switching noise on digital traces. Per Microchip datasheet DS40001882C, the crystal load capacitors (typically 12-18 pF) should be sized to match the crystal's rated load capacitance (CL). Keep the SERCOM I2C / SPI / UART traces short (<50 mm) and route them away from the USB DP/DM differential pair to avoid crosstalk. The USB DP/DM traces should be 90 ohm differential and matched within 0.5 mm.
규정 준수 정보
RoHS compliant and Pb-free per Microchip 'Green' designation. Standard -CU variant is industrial grade; AEC-Q100 qualified -AUT variant available for automotive. Halogen-free status not stated in the verified data.
