ATSAMD51P19A-CTUT-EFP - 120MHz Cortex-M4F MCU 512KB Flash | Microchip
부품 번호: ATSAMD51P19A-CTUT-EFP ✓ 활성| 수량 | 단가 | 합계 |
|---|---|---|
| 1 | $8.95 | $8.95 |
| 10 | $8.06 | $80.60 |
| 100 | $7.16 | $716.00 |
| 500 | $6.45 | $3,225.00 |
| 1,000 | $5.74 | $5,740.00 |
ATSAMD51P19A-CTUT-EFP 개요
A microcontroller (MCU) is a single-chip computer that integrates a processor core, memory (Flash for code, SRAM for data), and a rich set of peripherals onto one die. The Cortex-M4F architecture belongs to ARM's microcontroller class, adding hardware single-precision floating-point acceleration and DSP instructions on top of the Thumb-2 instruction set. Within Microchip's hierarchy, the SAM D51 sits above the SAM D21 (Cortex-M0+) and SAM D11 (Cortex-M0+) as a high-performance general-purpose family, beneath the Cortex-M7-based SAME70/SAMS70 line, and shares its D5x/E5x platform with the lower-pin-count SAM E51 variants.
Key features include up to 120 MHz CPU clock, 512 KB dual-panel Flash with ECC, 192 KB SRAM with ECC, an integrated full-speed USB 2.0 device/host interface, 99 programmable I/O lines, multiple SERCOM (serial communication) interfaces, a 12-bit ADC and 12-bit DAC, and a Cryptographic True Random Number Generator. The Cortex-M4F core delivers 1.25 DMIPS/MHz with DSP extensions, while the on-chip FPU removes the throughput penalty of software floating-point math used in motor control or sensor-fusion algorithms.
Architecturally the SAM D51 uses a multi-layer AHB bus matrix giving the CPU, DMA, and peripherals parallel access to SRAM and Flash, which removes the usual contention bottleneck seen on simpler MCUs. ECC on both Flash and SRAM targets safety-critical IEC 60730 class B firmware regimes. The Extended Flash Performance suffix indicates the variant is rated for higher endurance / industrial-grade Flash operation than the non-EFP base part.
Typical applications include industrial HMI panels, USB peripherals and human-interface devices, IoT sensor hubs, motor control with FOC, and audio processing. When designing with this part, allocate decoupling capacitance per the datasheet's recommended power-supply network and follow the 120-pin TFBGA escape routing guidelines to maintain signal integrity on the high-speed SERCOM and USB lines.
드롭인 대체품: ATSAMD51P19A-CTUT-EFP — 동일 패키지, 핀 호환. PCB 재작업이 필요한 다른 패키지 부품은 제외됩니다.
이 시리즈의 변형
다음과 드롭인 호환되는 동일 시리즈 모델: ATSAMD51P19A-CTUT-EFP (동일 폼 팩터 및 풋프린트) — 차이점: Package, Core Architecture, USB, ADC, DAC.
빠른 비교 도구 — 나란히 비교할 대체 부품을 선택하십시오:
ATSAMD51P19A-CTUT
✅ 드롭인✓ 재고 있음
$5.55 / 개
데이터시트 보기 →ATSAMD51P19A-AFT
✅ 드롭인✓ 재고 있음
$6.18 / 개
데이터시트 보기 →ATSAMD51P19A-MUT-EFP
✅ 드롭인📋 참조 대체품 (카탈로그에 없음)
ATSAMD51P19A-CTUT-EFP 최대 정격 & 전기적 특성
| Core Architecture | ARM Cortex-M4F (32-bit) |
| Maximum CPU Clock | 120 MHz |
| FPU | Yes, single-precision hardware |
| DSP Instructions | Yes (Thumb-2 + SIMD) |
| Flash Memory | 512 KB (512K x 8) with ECC |
| SRAM | 192 KB with ECC |
| 공급 전압 | 1.71 V to 3.63 V |
| 동작 온도 | -40 C to +85 C |
| 패키지 | 120-TFBGA (8x8 mm) |
| Programmable I/O Lines | 99 |
| ADC | 12-bit |
| DAC | 12-bit |
| USB | USB 2.0 Full-Speed Device/Host |
| 실장 유형 | Surface Mount |
| RoHS 상태 | Compliant |
ATSAMD51P19A-CTUT-EFP 120-tfbga (8x8 mm) 핀 구성 가이드
ATSAMD51P19A-CTUT-EFP(120-tfbga (8x8 mm) 패키지)의 핀 구성입니다. 이 디지털 IC에는 GPIO, 통신 인터페이스(UART, SPI, I2C), 전원 핀이 포함되어 있습니다. 대체 핀 기능과 구성 옵션은 제조사 데이터시트를 참조하십시오. 임베디드 시스템 설계와 PCB 레이아웃에 필수적입니다.
다음에 대한 상세 핀아웃 데이터 없음: ATSAMD51P19A-CTUT-EFP.
다음을 참조하십시오: 데이터시트 전체 핀 구성은 다음을 참조하십시오.
일반적인 애플리케이션
ATSAMD51P19A-CTUT-EFP 적합 용도: 6 애플리케이션s: Industrial Human-Machine Interface (HMI), USB Audio Class Device (USB Headphone / DAC), Field-Oriented Control (FOC) Motor Drive, IoT Sensor Hub with USB-C Connectivity, Portable Medical Data Logger, Audio Effects Pedal / DSP Module.
Industrial Human-Machine Interface (HMI)
The ATSAMD51P19A-CTUT-EFP's 120 MHz Cortex-M4F with FPU drives color TFT displays up to 480x272 with smooth 60 fps touch response and on-chip USB for firmware-update HIDs. Its 192 KB SRAM holds double-buffered framebuffers and font tables without external memory. ECC-protected Flash allows reliable storage of UI assets and multilingual strings. The 1.71-3.63 V supply and -40 to +85 C range fit industrial cabinet environments, while the 99 I/O lines route capacitive-touch I2C, RGB display bus, and RS-485 fieldbus concurrently.
추천
USB Audio Class Device (USB Headphone / DAC)
The ATSAMD51P19A-CTUT-EFP integrates a full-speed USB 2.0 device/host PHY and 12-bit DAC, enabling USB Audio Class 1.0 headphone designs at 48 kHz / 24-bit. The Cortex-M4F hardware FPU performs biquad filtering and dynamic-range compression in real time without CPU stalls. Its 192 KB SRAM holds USB endpoint buffers plus an audio frame ring, removing the need for an external memory chip. The 120-TFBGA package keeps the PCB small for in-line dongle form factors while exposing 99 I/O for tactile-button and LED-bar interfaces.
추천
Field-Oriented Control (FOC) Motor Drive
FOC algorithms on PMSM and BLDC motors demand single-precision floating-point math and tight PWM-synchronization. The ATSAMD51P19A-CTUT-EFP's Cortex-M4F FPU runs Park/Clarke transforms and SVPWM at <10 us loop time, leaving headroom for speed PI and current-control loops at 20 kHz. The 12-bit ADC with hardware oversampling captures phase currents at the PWM center, while the integrated 12-bit DAC provides debug-output of internal variables. ECC Flash protects motor-parameter storage from bit-flips in 24 V industrial-bus environments.
추천
IoT Sensor Hub with USB-C Connectivity
USB-C-powered IoT hubs need a single-chip solution combining USB host, sensor I/O, and on-board processing. The ATSAMD51P19A-CTUT-EFP integrates full-speed USB host for HID and CDC class devices, multiple SERCOM ports for I2C/SPI sensors, and 99 I/O for relay and LED-driver expansion. Its 512 KB Flash runs MicroPython or FreeRTOS, while the FPU accelerates sensor-fusion math for IMUs. The Extended Flash Performance suffix extends Flash endurance for always-on data-logging applications typical in industrial IoT gateways.
추천
Portable Medical Data Logger
Battery-powered medical monitors and connected-health wearables benefit from the ATSAMD51P19A-CTUT-EFP's 1.71-3.63 V wide supply range, hardware FPU for biosignal DSP, and ECC Flash/SRAM that supports IEC 60730 class B firmware regimes. The 12-bit ADC samples ECG or pulse-oximetry signals at high sample rates, while the integrated USB Full-Speed PHY enumerates as a vendor-class device to a host PC for real-time waveform streaming. ECC memory helps catch single-bit upsets critical in patient-monitoring reliability analysis.
추천
Audio Effects Pedal / DSP Module
Guitar and pro-audio pedal designers benefit from the ATSAMD51P19A-CTUT-EFP's hardware single-precision FPU, which runs reverb/chorus/distortion algorithms at 48 kHz with negligible CPU overhead. The 192 KB SRAM buffers multiple audio channels simultaneously without external memory, and the 12-bit ADC/DAC are well-matched to line-level instrument signals after op-amp conditioning. USB Device-class support enables MIDI-over-USB and firmware-update workflows, while the 120-TFBGA package fits in compact stomp-box enclosures.
추천
추천 제품 요약
엔지니어링 참조 데이터: ATSAMD51P19A-CTUT-EFP — 비교, 설계 지침 및 규정 준수 정보.
선택 가이드
대체품과의 비교
| 파라미터 | 이 제품 | ATSAMD51P19A-CTUT | ATSAMD51P19A-AFT | ATSAMD51P19A-MUT-EFP | ATSAMD51N19A-AUT-EFP | ATSAMD51J19A-MU |
|---|---|---|---|---|---|---|
| Package | 120-TFBGA (8x8 mm) | 120-TFBGA (8x8 mm) - same | 120-TFBGA (8x8 mm) - same | 120-TFBGA (8x8 mm) - same | 128-TQFP (14x14 mm) - different | 64-QFN - different |
| Brand | Microchip Technology | Microchip Technology | Microchip Technology | Microchip Technology | Microchip Technology | Microchip Technology |
| Core | ARM Cortex-M4F | ARM Cortex-M4F | ARM Cortex-M4F | ARM Cortex-M4F | ARM Cortex-M4F | ARM Cortex-M4F |
| Maximum Clock | 120 MHz | 120 MHz | 120 MHz | 120 MHz | 120 MHz | 120 MHz |
| Flash Memory | 512 KB with ECC | 512 KB with ECC | 512 KB with ECC | 512 KB with ECC | 512 KB with ECC | 512 KB with ECC |
| SRAM | 192 KB with ECC | 192 KB with ECC | 192 KB with ECC | 192 KB with ECC | 192 KB with ECC | 192 KB with ECC |
| I/O Pins | 99 | 99 | 99 | 99 | 99 | 51 |
| Extended Flash Performance (EFP) | Yes | No | No | Yes | Yes | No |
| Supply Voltage | 1.71 V to 3.63 V | 1.71 V to 3.63 V | 1.71 V to 3.63 V | 1.71 V to 3.63 V | 1.71 V to 3.63 V | 1.71 V to 3.63 V |
주요 차별점
- Extended Flash Performance (EFP) for high-write-cycle industrial use (vs ATSAMD51P19A-CTUT)
- Largest I/O count in the SAM D51 family (vs ATSAMD51J19A-MU)
- BGA package optimizes PCB footprint for high-density designs (vs ATSAMD51N19A-AUT-EFP (TQFP-128))
설계 노트
Route the 120-TFBGA escape using micro-via-in-pad or dog-bone fanout with 0.4 mm pitch traces; per Microchip's SAM D51 hardware-design guidelines place 100 nF X7R decoupling on every VDD pin within 1 mm trace length, plus a single 4.7 uF bulk cap per rail. Keep the 32 kHz crystal traces short and symmetric to avoid oscillator startup failure, and isolate the integrated USB PHY D+/D- lines with 90-ohm differential impedance to meet USB 2.0 Full-Speed signal-integrity requirements.
Do not skip the NVM Security Bit fuse configuration when designing with ATSAMD51P19A-CTUT-EFP for production. According to the SAM D5X/E5X errata, certain DFP/DFLL configurations require the user's firmware to re-lock the BOCOR register after boot to prevent runaway clock failure. Also note that SERCOM pin-mux conflicts can silently break I2C transactions if multiple peripherals claim the same PAD - use ASF or MPLAB Harmony's pin-mux tool to validate before layout tape-out.
When operating ATSAMD51P19A-CTUT-EFP from a USB 5 V rail, use a 3.3 V LDO (such as the AP2112K-3.3) with at least 200 mA rating to cover the MCU's active current peaks and the USB peripheral load. The 1.71 V minimum allows direct Li-Ion operation (3.0-4.2 V) with a buck regulator. Enable the on-chip voltage regulator with a 1 uF + 100 nF decoupling network on VDDOUT to keep core rail noise below the datasheet's 30 mVpp tolerance.
규정 준수 정보
RoHS and lead-free compliance per Microchip product page. Not AEC-Q100 qualified - this part targets industrial and consumer applications, not automotive. JLCPCB listing confirms ROHS compliance.
