DSPIC33EV256GM003-I/M5 - 16-bit 70 MIPS DSC 256KB Flash | Microchip
부품 번호: DSPIC33EV256GM003-I/M5 ✓ 활성| 수량 | 단가 | 합계 |
|---|---|---|
| 1 | $5.2 | $5.20 |
| 10 | $4.68 | $46.80 |
| 100 | $4.16 | $416.00 |
| 500 | $3.74 | $1,870.00 |
| 1,000 | $3.35 | $3,350.00 |
DSPIC33EV256GM003-I/M5 개요
A digital signal controller combines the computational throughput of a digital signal processor (DSP) with the peripheral integration and control architecture of a microcontroller (MCU). Within the power management hierarchy, the dsPIC33EV family sits in Microchip's 16-bit dsPIC33E line, positioned above general-purpose PIC16/PIC18 MCUs and optimized for closed-loop control loops and harsh-environment sensing.
Key features include a 5V-tolerant design rated for harsh environments, six motor control PWM channels (6 MC PWM), three integrated operational amplifiers, a Charge Time Measurement Unit (CTMU) for capacitive touch and time-domain measurements, and SENT protocol support for automotive sensor interfaces. ECC Flash provides single-bit error correction for functional-safety-oriented designs, which is why DigiKey classifies the part under Functional Safety (FuSa) microcontrollers.
Architecturally, the device executes the dsPIC33E 16-bit pipeline at up to 70 MIPS, with DSP multiply-accumulate (MAC) instructions and 4 DMA channels enabling efficient filtering, FOC motor control, and sensor-fusion workloads without CPU saturation. On-chip op amps can close current-sense loops internally, reducing external BOM count in motor drives.
Typical applications include brushless DC and PMSM motor control in appliances, automotive sensors and touch/control units, industrial power conversion, and noise/vibration-tolerant embedded control in harsh environments.
Design consideration: the 5V core supply simplifies noise immunity in electrically harsh automotive and appliance environments compared to 3.3V-only MCUs, but verify 5V peripheral signal levels against connected logic.
This page synthesizes distributor pricing, same-footprint alternatives, and practical design notes not found in the manufacturer datasheet.
드롭인 대체품: DSPIC33EV256GM003-I/M5 — 동일 패키지, 핀 호환. PCB 재작업이 필요한 다른 패키지 부품은 제외됩니다.
이 시리즈의 변형
다음과 드롭인 호환되는 동일 시리즈 모델: DSPIC33EV256GM003-I/M5 (동일 폼 팩터 및 풋프린트) — 차이점: Core, Package, RAM, Supply Voltage, Operating Temperature.
빠른 비교 도구 — 나란히 비교할 대체 부품을 선택하십시오:
DSPIC33EV256GM003-E/M5
✅ 드롭인✓ 재고 있음
$3.58 / 개
데이터시트 보기 →DSPIC33EV256GM003-H/M5
✅ 드롭인📋 참조 대체품 (카탈로그에 없음)
DSPIC33EV128GM103T-I/M5
✅ 드롭인 ⚠️ 사양 미검증✓ 재고 있음
$3.52 / 개
데이터시트 보기 →DSPIC33EP64GP503-I/M5
✅ 드롭인 ⚠️ 사양 미검증✓ 재고 있음
$3.32 / 개
데이터시트 보기 →DSPIC33EP64GP503-E/TL
✅ 드롭인 ⚠️ 사양 미검증✓ 재고 있음
$3.48 / 개
데이터시트 보기 →DSPIC33EV256GM003-I/M5 최대 정격 & 전기적 특성
| Core | dsPIC33E 16-bit |
| Max CPU Speed | 70 MIPS (60 MHz per Mouser listing) |
| Program Memory | 256KB (85.5K x 24) ECC Flash |
| RAM | 16 KB |
| 공급 전압 | 4.5 V to 5.5 V (5V DSC) |
| Motor Control PWM | 6 MC PWM |
| Integrated Op Amps | 3 |
| CTMU | Yes (Charge Time Measurement Unit) |
| SENT Support | Yes |
| DMA Channels | 4 |
| Timers | 7 |
| Functional Safety Class | FuSa (per DigiKey classification) |
| 동작 온도 | -40C to +85C (I-grade) |
| 패키지 | 36-UQFN (5x5 mm) with exposed pad |
| 실장 유형 | Surface Mount |
| Target Applications | Appliances, industrial, automotive |
DSPIC33EV256GM003-I/M5 36-uqfn (5x5 mm) with exposed pad 핀 구성 가이드
DSPIC33EV256GM003-I/M5(36-uqfn (5x5 mm) with exposed pad 패키지)의 핀 구성입니다. 이 디지털 IC에는 GPIO, 통신 인터페이스(UART, SPI, I2C), 전원 핀이 포함되어 있습니다. 대체 핀 기능과 구성 옵션은 제조사 데이터시트를 참조하십시오. 임베디드 시스템 설계와 PCB 레이아웃에 필수적입니다.
다음에 대한 상세 핀아웃 데이터 없음: DSPIC33EV256GM003-I/M5.
다음을 참조하십시오: 데이터시트 전체 핀 구성은 다음을 참조하십시오.
일반적인 애플리케이션
DSPIC33EV256GM003-I/M5 적합 용도: 6 애플리케이션s: BLDC/PMSM Motor Control, Automotive Sensors and Control Units, Home Appliances, Industrial Power Conversion, Capacitive Touch and HMI, Harsh-Environment Embedded Control.
BLDC/PMSM Motor Control
The DSPIC33EV256GM003-I/M5 is purpose-built for three-phase motor control: its 70 MIPS DSP core executes field-oriented control (FOC) inner loops at 10-20 kHz PWM frequencies with headroom for sensorless observers, while the 6 motor-control PWM channels provide complementary outputs with hardware dead-time for the three-phase inverter bridge. The 3 on-chip operational amplifiers amplify low-side shunt currents internally, eliminating external op amps and shrinking the BOM. Microchip markets this exact family as a '5V Robust DSC with Safety Motor Control'; ECC Flash protects the control firmware against single-bit upsets. Place the UQFN near the gate drivers with short PWM traces to limit ringing.
추천
Automotive Sensors and Control Units
Microchip explicitly targets dsPIC33EV GM devices at automotive sensors and touch/control units operating amid noise and vibration. The 4.5V-5.5V supply tolerates automotive load-dump-adjacent conditions better than 3.3V MCUs, and the SENT interface speaks the single-edge-nibble transport protocol common to automotive sensor links. The CTMU supports capacitive-touch HMI panels and precise ratiometric measurements, while the 36-UQFN 5x5 mm footprint fits compact sensor pods. For under-hood placement, pair this -I grade part with the -H/M5 variant rated to 150C. Use SENT and CRC-checked communication to meet diagnostics expectations in body and powertrain nodes.
추천
Home Appliances
Appliance motor drives - washing machines, refrigerators, dishwashers, and fans - benefit directly from the dsPIC33EV's 5V robustness, which withstands the conducted noise and voltage sag typical of appliance power electronics. The 70 MIPS core runs single-shunt or three-shunt FOC at 16 kHz PWM, the 3 integrated op amps condition shunt feedback, and ECC Flash preserves firmware integrity over years of compressor cycling. Microchip lists appliances as a flagship dsPIC33EV market. The 5x5 mm UQFN with exposed pad dumps roughly 0.5-1 W into the PCB; provide a solid ground-plane copper area under the exposed pad to keep junction temperatures well below the 125C industrial limit.
추천
Industrial Power Conversion
In industrial converters - PFC stages, small inverters, and digital power supplies - the DSPIC33EV256GM003-I/M5 provides deterministic ADC-triggered control loops: the 70 MIPS core and 4 DMA channels move samples without CPU stalls, and 6 MC PWM channels drive interleaved or phase-shifted topologies. The 5V I/O level interfaces cleanly with gate-driver logic and industrial sensors that still use 5V signaling, avoiding level shifters. The 256KB ECC Flash accommodates firmware with logging, diagnostics, and multiple operating profiles. Microchip's harsh-environment qualification covers factory floor vibration and temperature; derate junction temperature targets to 105C for long service life in enclosed industrial cabinets.
추천
Capacitive Touch and HMI
The on-chip CTMU (Charge Time Measurement Unit) turns the DSPIC33EV256GM003-I/M5 into a capacitive-touch controller without an external touch IC: charge-time measurements on sensor pads detect touches through glass or plastic overlays, and Microchip's touch libraries implement drift compensation and multi-key scanning. In appliance and automotive control units - where Microchip specifically positions the EV family for 'touch and control units' - the same DSC runs the HMI scan and the application logic, consolidating two chips into one. The 5V supply improves touch SNR in noisy motor-drive environments where 3.3V touch solutions struggle. Budget CPU load for touch scanning alongside control loops, or offload scanning to timer-triggered CTMU conversions.
추천
Harsh-Environment Embedded Control
General embedded control in harsh environments - pumps, compressors, agricultural equipment, and outdoor equipment controllers - leverages the dsPIC33EV's 5V noise immunity, -40C to +85C I-grade rating, and ECC Flash. The 70 MIPS core with DSP MAC instructions handles filtering, sensor fusion, and communication stacks concurrently, while 7 timers and 4 DMA channels manage PWM generation, quadrature decoding, and UART/SPI traffic without CPU overhead. The 36-UQFN 5x5 mm package with exposed pad provides low-inductance grounding for noisy power contexts. For extreme ambient locations such as engine bays, substitute the pin-identical -H/M5 variant rated to 150C without any PCB change.
추천
추천 제품 요약
엔지니어링 참조 데이터: DSPIC33EV256GM003-I/M5 — 비교, 설계 지침 및 규정 준수 정보.
선택 가이드
대체품과의 비교
| 파라미터 | 이 제품 | DSPIC33EV256GM003-E/M5 | DSPIC33EV256GM003-H/M5 | DSPIC33EV128GM103T-I/M5 | DSPIC33EP64GP503-I/M5 |
|---|---|---|---|---|---|
| Package | 36-UQFN (5x5 mm) | 36-UQFN (5x5 mm) - same | 36-UQFN/PQCC (5x5 mm) - same | 36-UQFN (5x5 mm) - same | 36-UQFN (5x5 mm) - same |
| Brand | Microchip Technology | Microchip Technology | Microchip Technology | Microchip Technology | Microchip Technology |
| Program Flash | 256 KB ECC | 256 KB ECC | 256 KB ECC | 128 KB | 64 KB |
| Operating Temperature | -40C to +85C (I) | -40C to +125C (E) | -40C to +150C (H) | -40C to +85C (I) | -40C to +85C (I) |
주요 차별점
- 256KB ECC Flash in a 36-UQFN 5x5 mm footprint (vs DSPIC33EV128GM103T-I/M5)
- Full EV-family motor-control peripheral set (vs DSPIC33EP64GP503-I/M5)
- Temperature-grade scalability without redesign (vs DSPIC33EV256GM003-H/M5)
설계 노트
The 36-UQFN 5x5 mm package uses an exposed thermal pad that must be soldered to a grounded copper pour for both thermal dissipation and low-inductance grounding. Use a 5x5 array of thermal vias (0.3 mm drill, filled or tented) connecting the pad to inner ground planes. Per standard Microchip QFN layout guidance, keep decoupling capacitors (100 nF plus 10 uF per supply pin) within 2 mm of their pins and route PWM outputs on a layer adjacent to a solid ground plane to limit loop area and motor-drive ringing.
This device runs on 4.5V-5.5V, so all I/O signals swing at 5V logic levels. Do not connect I/O directly to 3.3V-only peripherals or sensor ICs without level shifting or verifying 5V tolerance - this is the most common migration mistake from 3.3V MCUs. Also confirm the exact flash size needed: if firmware plus bootloader approaches 128KB, select the 256KB part (this MPN) rather than the DSPIC33EV128GM103T-I/M5, since re-spinning the board for a larger die later is unnecessary given identical footprints.
Estimated: at 5V and typical DSC operating current of tens of mA (core plus peripherals at 60-70 MIPS, exact figure per datasheet DC characteristics), power dissipation is on the order of 0.2-0.5 W. With the exposed pad properly soldered, the UQFN keeps junction rise modest; verify with the datasheet theta_JA and your airflow condition. For motor-control designs, keep the analog supply (AVDD) filtered with an RC or ferrite from the digital 5V rail so the integrated op amps deliver clean current-sense feedback to the ADC during PWM switching events.
규정 준수 정보
Compliance statuses were not stated in the verified web data; confirm RoHS/REACH status on the Microchip product page or the distributor environmental datasheet before procurement.
