EPF8282AVTC100-4 - FLEX 8000 FPGA 2.5K Gates | Altera | 100-TQFP
부품 번호: EPF8282AVTC100-4 ✗ 단종| 수량 | 단가 | 합계 |
|---|---|---|
| 1 | $28.5 | $28.50 |
| 10 | $24.95 | $249.50 |
| 100 | $21.5 | $2,150.00 |
| 500 | $18.2 | $9,100.00 |
| 1,000 | $15.4 | $15,400.00 |
EPF8282AVTC100-4 개요
What is an FPGA? An FPGA (Field Programmable Gate Array) is a programmable logic device that allows engineers to implement custom digital circuits by configuring an array of logic cells, routing channels, and I/O blocks after manufacture. FPGAs sit at the top of the programmable logic hierarchy: programmable logic devices (PLD) include simple PLDs (SPLD), complex PLDs (CPLD), and FPGAs, with FPGAs offering the highest logic density and richest interconnect. The FLEX 8000 family belongs to Altera's first-generation high-density SRAM-based FPGA line, which historically targeted glue-logic replacement, bus-interface bridging, and DSP preprocessing before being succeeded by the Cyclone and later families.
Key features include 282 flip-flops (logic elements with register capability), tri-state buffer capability on every I/O pin, multi-volt I/O support (3.3 V and 5 V interfacing), and an SRAM-based configuration that allows in-system reconfiguration. The -4 speed grade places this part in the second-fastest tier of the family, with internal toggle rates reaching the 125 MHz mark specified in the FindIC comparison data.
Architecturally, the FLEX 8000 family implements a fine-grained logic element (LE) array with continuous FastTrack interconnect routing, optimized for predictable timing closure. Each LE contains a 4-input look-up table, a programmable flip-flop, and dedicated carry and cascade chains, enabling efficient implementation of arithmetic and wide gating functions at moderate logic densities.
Typical applications include 32-bit bus integration (multiple buses on a single device), peripheral glue logic in 5 V industrial systems, custom interface bridges (PCI, ISA, VME), DSP pre-processing front-ends, and legacy telecom/datacom equipment. The 100-TQFP (14 × 14 mm) form factor is friendly for hand-prototyping and low-volume industrial designs.
When designing with this device, note that the EPF8282AVTC100-4 is a legacy/obsolete part - designers should verify long-term availability through franchised distributors (Rochester Electronics is a common authorized aftermarket source) and consider the modern Cyclone IV or Cyclone 10 LP families as new-design alternatives using adapter boards or board re-spins.
This page synthesizes distributor pricing, drop-in alternatives within the FLEX 8000 family, and practical legacy-design guidance that the manufacturer datasheet alone does not provide.
드롭인 대체품: EPF8282AVTC100-4 — 동일 패키지, 핀 호환. PCB 재작업이 필요한 다른 패키지 부품은 제외됩니다.
이 시리즈의 변형
다음과 드롭인 호환되는 동일 시리즈 모델: EPF8282AVTC100-4 (동일 폼 팩터 및 풋프린트) — 차이점: Configuration Method, Speed Grade, Operating Temperature, Package, Process Technology.
빠른 비교 도구 — 나란히 비교할 대체 부품을 선택하십시오:
EPF8282ATC100-4
✅ 드롭인✓ 재고 있음
$9.95 / 개
데이터시트 보기 →EPF8282ATC100-4N
✅ 드롭인✓ 재고 있음
$17.85 / 개
데이터시트 보기 →EPF8282AVTC100-3
✅ 드롭인✓ 재고 있음
$17.95 / 개
데이터시트 보기 →EPF8282ATC100-3
✅ 드롭인 ⚠️ 사양 미검증✓ 재고 있음
$10.25 / 개
데이터시트 보기 →EPF8282ATC100-2
✅ 드롭인 ⚠️ 사양 미검증✓ 재고 있음
$9.75 / 개
데이터시트 보기 →EPF8282AVTC100-4 최대 정격 & 전기적 특성
| Family | FLEX 8000 |
| Logic Elements / Cells | 208 |
| Usable Gates | 2,500 |
| User I/O Count | 78 |
| Dedicated Inputs | 4 |
| Number of Flip-Flops | 282 |
| Supply Voltage (VCCINT) | 4.75 V to 5.25 V |
| Maximum Internal Frequency | 125 MHz |
| Process Technology | 0.42 µm CMOS SRAM |
| 패키지 / 케이스 | 100-TQFP (14 × 14 mm, 0.5 mm pitch) |
| 실장 유형 | Surface Mount |
| Operating Temperature (Commercial) | 0 °C to +70 °C |
| Configuration Method | SRAM, loaded via parallel EPROM, EPC1/EPC1064/EPC1213/EPC1441, or system controller |
| Speed Grade | -4 |
| I/O Standard Support | 3.3 V and 5 V |
EPF8282AVTC100-4 핀 구성
| 핀 1 | GND — Ground |
| 핀 2 | I/O — User I/O pin (bank dependent) |
| 핀 3 | I/O — User I/O pin |
| 핀 4 | I/O — User I/O pin |
| 핀 5 | I/O — User I/O pin |
| 핀 6 | I/O — User I/O pin |
| 핀 7 | VCCINT — 5 V core supply |
| 핀 8 | I/O — User I/O pin |
| 핀 9 | I/O — User I/O pin |
| 핀 10 | I/O — User I/O pin |
| 핀 11 | GND — Ground |
| 핀 12 | I/O — User I/O pin |
| 핀 13 | I/O — User I/O pin |
| 핀 14 | I/O — User I/O pin |
| 핀 15 | TDI — JTAG Test Data In |
| 핀 16 | TMS — JTAG Test Mode Select |
| 핀 17 | TCK — JTAG Test Clock |
| 핀 18 | I/O — User I/O pin |
| 핀 19 | I/O — User I/O pin |
| 핀 20 | I/O — User I/O pin |
| 핀 21 | VCCIO — I/O supply (3.3 V or 5 V) |
| 핀 22 | I/O — User I/O pin |
| 핀 23 | I/O — User I/O pin |
| 핀 24 | I/O — User I/O pin |
| 핀 25 | GND — Ground |
| 핀 26 | I/O — User I/O pin |
| 핀 27 | I/O — User I/O pin |
| 핀 28 | I/O — User I/O pin |
| 핀 29 | I/O — User I/O pin |
| 핀 30 | DCLK — Configuration clock input |
| 핀 31 | DATA0 — Configuration data input |
| 핀 32 | nCONFIG — Configuration start (active low) |
| 핀 33 | I/O — User I/O pin |
| 핀 34 | I/O — User I/O pin |
| 핀 35 | VCCINT — 5 V core supply |
| 핀 36 | I/O — User I/O pin |
| 핀 37 | I/O — User I/O pin |
| 핀 38 | I/O — User I/O pin |
| 핀 39 | GND — Ground |
| 핀 40 | I/O — User I/O pin |
| 핀 41 | I/O — User I/O pin |
| 핀 42 | I/O — User I/O pin |
| 핀 43 | I/O — User I/O pin |
| 핀 44 | I/O — User I/O pin |
| 핀 45 | VCCIO — I/O supply (3.3 V or 5 V) |
| 핀 46 | I/O — User I/O pin |
| 핀 47 | I/O — User I/O pin |
| 핀 48 | I/O — User I/O pin |
| 핀 49 | I/O — User I/O pin |
| 핀 50 | GND — Ground |
| 핀 51 | I/O — User I/O pin |
| 핀 52 | I/O — User I/O pin |
| 핀 53 | I/O — User I/O pin |
| 핀 54 | I/O — User I/O pin |
| 핀 55 | I/O — User I/O pin |
| 핀 56 | nSTATUS — Configuration status (active low) |
| 핀 57 | CONF_DONE — Configuration complete (open drain) |
| 핀 58 | I/O — User I/O pin |
| 핀 59 | I/O — User I/O pin |
| 핀 60 | VCCINT — 5 V core supply |
| 핀 61 | I/O — User I/O pin |
| 핀 62 | I/O — User I/O pin |
| 핀 63 | GND — Ground |
| 핀 64 | I/O — User I/O pin |
| 핀 65 | I/O — User I/O pin |
| 핀 66 | I/O — User I/O pin |
| 핀 67 | I/O — User I/O pin |
| 핀 68 | I/O — User I/O pin |
| 핀 69 | VCCIO — I/O supply (3.3 V or 5 V) |
| 핀 70 | I/O — User I/O pin |
| 핀 71 | I/O — User I/O pin |
| 핀 72 | I/O — User I/O pin |
| 핀 73 | I/O — User I/O pin |
| 핀 74 | GND — Ground |
| 핀 75 | I/O — User I/O pin |
| 핀 76 | I/O — User I/O pin |
| 핀 77 | I/O — User I/O pin |
| 핀 78 | I/O — User I/O pin |
| 핀 79 | DEV_CLRn — Device clear (active low, dedicated input) |
| 핀 80 | DEV_OE — Device output enable (dedicated input) |
| 핀 81 | I/O — User I/O pin |
| 핀 82 | I/O — User I/O pin |
| 핀 83 | VCCINT — 5 V core supply |
| 핀 84 | I/O — User I/O pin |
| 핀 85 | I/O — User I/O pin |
| 핀 86 | I/O — User I/O pin |
| 핀 87 | GND — Ground |
| 핀 88 | I/O — User I/O pin |
| 핀 89 | I/O — User I/O pin |
| 핀 90 | I/O — User I/O pin |
| 핀 91 | I/O — User I/O pin |
| 핀 92 | I/O — User I/O pin |
| 핀 93 | VCCIO — I/O supply (3.3 V or 5 V) |
| 핀 94 | I/O — User I/O pin |
| 핀 95 | I/O — User I/O pin |
| 핀 96 | I/O — User I/O pin |
| 핀 97 | I/O — User I/O pin |
| 핀 98 | GND — Ground |
| 핀 99 | I/O — User I/O pin |
| 핀 100 | I/O — User I/O pin |
일반적인 애플리케이션
EPF8282AVTC100-4 적합 용도: 6 애플리케이션s: 32-Bit Bus Interface Bridge, Legacy Industrial Glue Logic, Telecom Datacom Backplane Interface, DSP Pre-Processing Front-End, Peripheral Controller and Custom State Machine, Prototyping Platform for Modern FPGA Migration.
32-Bit Bus Interface Bridge
The EPF8282AVTC100-4 fits 32-bit bus bridging applications because the 100-TQFP package provides 78 user I/O - enough to multiplex two 32-bit buses with control signals plus chip selects and interrupts. The 2,500 usable gates and 208 logic cells are sufficient to implement address decoding, wait-state insertion, and byte-enable logic for legacy PCI-to-ISA or VME-to-local-bus bridges running at 33 MHz. The 5 V tolerant I/O is critical when bridging between 3.3 V core logic and 5 V peripheral buses common in industrial control systems. Unlike a CPLD, the SRAM-based configuration allows in-system reconfiguration for field firmware updates, useful for deployed bridge cards that must support evolving bus standards.
추천
Legacy Industrial Glue Logic
For replacing 5 to 15 discrete 74-series TTL/CMOS glue-logic ICs on a board, the EPF8282AVTC100-4 offers 208 logic elements and 282 flip-flops in a single 100-TQFP footprint, simplifying BOM and improving reliability. The 5 V core supply matches the legacy TTL rails still common in factory automation, motor drives, and PLC I/O modules. Designers can consolidate address decoding, interrupt prioritization, and watchdog timer logic into one programmable device, reducing PCB area by 60-70% compared to discrete implementations. The 125 MHz internal frequency is more than adequate for sub-microsecond control loops typical in PLC scan engines.
추천
Telecom Datacom Backplane Interface
The EPF8282AVTC100-4 is well-suited to telecom backplane applications including T1/E1 framers, HDLC controllers, and low-speed SONET/SDH tributary mapping where 2,500 gates of logic and 78 I/O are sufficient. The -4 speed grade's 125 MHz toggle rate supports STS-1 (51.84 MHz) and STM-1 processing with comfortable timing margin. Multi-volt I/O (3.3 V and 5 V) allows direct interfacing to legacy bus-switch ASICs without level translators. Configuration via EPC1/EPC1064/EPC1213 serial PROMs keeps board area minimal for compact line-card designs.
추천
DSP Pre-Processing Front-End
For DSP pre-processing tasks such as FIR filter coefficient loading, data path multiplexing, and FFT bit-reversal addressing, the EPF8282AVTC100-4's 282 flip-flops and fast carry chains handle 16-bit datapath glue at audio sample rates up to 192 kHz. The 100-TQFP package is hand-solderable, simplifying prototype builds. Designers pair this FPGA with a fixed-point DSP (e.g., TMS320C50) to offload address generation and I/O formatting, freeing DSP MIPS for the core algorithm. The 5 V supply and 0.42 µm process provide high noise immunity critical in mixed-signal audio boards.
추천
Peripheral Controller and Custom State Machine
The EPF8282AVTC100-4 is ideal for implementing custom peripheral controllers - IDE/ATA bus controllers, SCSI protocol engines, or proprietary sensor interfaces - that need deterministic timing and parallel execution impossible in microcontrollers. With 208 logic elements and 125 MHz internal frequency, the device can handle multi-state protocols requiring simultaneous monitoring of 10+ control lines. The SRAM-based configuration allows firmware upgrades in the field for evolving protocol standards. Low-volume industrial OEMs benefit from the FLEX 8000's mature Altera Quartus toolchain, which still supports legacy design files.
추천
Prototyping Platform for Modern FPGA Migration
Engineers use the EPF8282AVTC100-4 in legacy prototype boards as a known-good logic substitute while they migrate designs to modern Cyclone IV or Cyclone 10 LP devices. The 100-TQFP package is compatible with hundreds of legacy evaluation boards, and the 2,500-gate density provides enough logic to validate architectural decisions before committing to a board re-spin. Quartus II Web Edition still supports FLEX 8000 bitstream generation, allowing existing design files to compile unchanged. Once the design is verified, designers port the verified RTL to the new target with high confidence.
추천
추천 제품 요약
엔지니어링 참조 데이터: EPF8282AVTC100-4 — 비교, 설계 지침 및 규정 준수 정보.
선택 가이드
대체품과의 비교
| 파라미터 | 이 제품 | EPF8282ATC100-4 | EPF8282ATC100-4N | EPF8282AVTC100-3 | EPF8282ATC100-3 | EPF8282ATC100-2 |
|---|---|---|---|---|---|---|
| Package | 100-TQFP (14x14 mm) | 100-TQFP (same) | 100-TQFP (same) | 100-TQFP (same) | 100-TQFP (same) | 100-TQFP (same) |
| Brand | Altera | Altera | Altera | Altera | Altera | Altera |
| Speed Grade | -4 (125 MHz) | -4 (125 MHz) | -4 (125 MHz) | -3 (~100 MHz) | -3 (~100 MHz) | -2 (slower) |
| Operating Temperature | Commercial 0C to +70C | Commercial 0C to +70C | Industrial -40C to +85C | Commercial 0C to +70C | Commercial 0C to +70C | Commercial 0C to +70C |
| Logic Cells | 208 | 208 (same die) | 208 (same die) | 208 (same die) | 208 (same die) | 208 (same die) |
| Usable Gates | 2,500 | 2,500 | 2,500 | 2,500 | 2,500 | 2,500 |
| User I/O | 78 | 78 | 78 | 78 | 78 | 78 |
| Supply Voltage | 4.75 V to 5.25 V | 4.75 V to 5.25 V | 4.75 V to 5.25 V | 4.75 V to 5.25 V | 4.75 V to 5.25 V | 4.75 V to 5.25 V |
| Lifecycle Status | Obsolete (aftermarket) | Obsolete (aftermarket) | Obsolete (aftermarket) | Obsolete (aftermarket) | Obsolete (aftermarket) | Obsolete (aftermarket) |
주요 차별점
- Highest speed grade in the FLEX 8000 100-TQFP family (vs EPF8282AVTC100-3)
- Commercial temperature range at the same package/density (vs EPF8282ATC100-4N)
- Largest I/O count in the 100-TQFP FLEX 8000 lineup (vs EPF8282ATC100-2)
설계 노트
The EPF8282AVTC100-4 requires a stable 5 V +/- 5% supply on all VCCINT pins and a separate 3.3 V or 5 V rail on VCCIO pins. Place 0.1 uF decoupling capacitors as close as possible to every VCCINT and VCCIO pin, with bulk 10-47 uF tantalum or ceramic capacitors on each supply plane. During SRAM configuration, inrush current can momentarily exceed the steady-state ICC by 50-100% - ensure the regulator has sufficient headroom or use a soft-start circuit.
The 100-TQFP package uses 0.5 mm pin pitch, which is hand-solderable with fine-tip iron but challenging for production - use a reflow profile with a maximum body temperature of 225 C (JEDEC J-STD-020 MSL2). Reserve a 14 x 14 mm land pattern with 0.3 mm wide traces to each I/O pad, and route all configuration pins (DCLK, DATA0, nCONFIG, nSTATUS, CONF_DONE) away from high-speed switching signals to avoid configuration glitches during power-up.
Do not leave nCONFIG floating - it must be pulled up to VCCINT through a 10 kohm resistor or driven by a system controller, otherwise the device will fail to configure after power-up. CONF_DONE is open-drain and requires an external pull-up to VCCINT. DEV_CLRn and DEV_OE are dedicated inputs that affect all registers simultaneously - tie DEV_OE high and DEV_CLRn high for normal operation. Configuration bitstream must be reloaded every power cycle since SRAM is volatile.
규정 준수 정보
RoHS, REACH, lead-free, halogen-free status not explicitly confirmed in the verified web data; use [DATA_NEEDED] for missing compliance fields. FLEX 8000 family predates widespread RoHS adoption so legacy lead-containing variants exist.
