EPM9560WC208-20C - 560-Macrocell EE PLD, 20ns, CQFP-208 | Altera
부품 번호: EPM9560WC208-20C ✗ 단종| 수량 | 단가 | 합계 |
|---|---|---|
| 1 | $285 | $285.00 |
| 10 | $245 | $2,450.00 |
| 100 | $198 | $19,800.00 |
| 500 | $165 | $82,500.00 |
| 1,000 | $140 | $140,000.00 |
EPM9560WC208-20C 개요
What is a Programmable Logic Device (PLD)? A PLD is a generic term for an integrated circuit whose logic function is defined by the end user after manufacture, rather than being hard-wired by the foundry. EE PLDs add non-volatile, electrically erasable configuration memory so the design can be re-programmed thousands of times in-circuit. The MAX 9000 family belongs to the higher-density tier of complex PLDs (CPLDs), bridging between classic 22V10-style PLDs and modern FPGAs in the programmable-logic taxonomy: PLD -> CPLD -> MAX 9000 -> high-density EE PLD. Compared with FPGAs, MAX 9000 parts offer deterministic timing, instant-on non-volatile configuration, and high pin-to-pin drive strength, which is why they remain favored in glue-logic, bus-interface, and legacy industrial designs.
Key features include 560 macrocells, 35 LABs, 149 user I/Os, 20 ns propagation delay, JTAG-based in-system programmability, and operation from a 3.3 V or 5 V supply. The architecture combines a global interconnect with per-macrocell registers, allowing both combinatorial and registered logic with predictable timing. Configurable I/O standards enable mixed-voltage interfacing without external level shifters.
Typical applications include legacy bus-interface glue logic in telecom and industrial backplanes, address decoding and wait-state generation in 5 V/3.3 V embedded systems, industrial control boards, and avionics/military systems that rely on the ceramic CQFP package for thermal and reliability robustness. The 208-pin ceramic package is selected where extended temperature, vibration tolerance, or hermeticity is required.
When designing with this part, mind the 20 ns tPD: at a 33 MHz bus it offers zero wait-state decode, but at 50 MHz external latches become necessary. Decoupling should follow Altera's MAX 9000 reference design with one 0.1 uF ceramic per VCC/GND pair plus a 10 uF tantalum bulk cap. The device is mature and obsolete/last-time-buy at most distributors, so design teams should verify lifecycle and pinout against the original Altera datasheet before committing to new layouts.
This page synthesizes distributor availability, parametric equivalents, and practical design notes not found in the manufacturer datasheet.
드롭인 대체품: EPM9560WC208-20C — 동일 패키지, 핀 호환. PCB 재작업이 필요한 다른 패키지 부품은 제외됩니다.
이 시리즈의 변형
다음과 드롭인 호환되는 동일 시리즈 모델: EPM9560WC208-20C (동일 폼 팩터 및 풋프린트) — 차이점: Package, Device Type, Operating Temperature Grade, Process Technology, RoHS Status.
빠른 비교 도구 — 나란히 비교할 대체 부품을 선택하십시오:
EPM9560RC208-20C
✅ 드롭인✓ 재고 있음
가격 문의
데이터시트 보기 →EPM9560RC208-20
✅ 드롭인✓ 재고 있음
가격 문의
데이터시트 보기 →EPM9560RC208-20N
✅ 드롭인✓ 재고 있음
가격 문의
데이터시트 보기 →EPM9560WC208-20
✅ 드롭인✓ 재고 있음
$25.8 / 개
데이터시트 보기 →EPM9560WC208-15C
✅ 드롭인✓ 재고 있음
$178 / 개
데이터시트 보기 →EPM9560WC208-15
✅ 드롭인✓ 재고 있음
$105 / 개
데이터시트 보기 →EPM9560WC208-20C 최대 정격 & 전기적 특성
| Device Family | MAX 9000 (EE PLD) |
| Series | EPM9560 |
| Macrocells | 560 |
| Logic Array Blocks (LABs) | 35 |
| User I/O Pins | 149 |
| Propagation Delay (tPD) | 20 ns |
| Process Technology | CMOS, Electrically Erasable |
| 공급 전압 | 3.3 V or 5 V (configurable I/O) |
| 패키지 | 208-pin CQFP (Ceramic Quad Flat Pack) |
| 핀 수 | 208 |
| Programming Interface | JTAG BST (in-system programmable) |
| Operating Temperature Grade | Commercial (C suffix) |
| 실장 유형 | Surface Mount (Ceramic QFP) |
| RoHS 상태 | ROHS3 Compliant (per fpgalink listing) |
| Moisture Sensitivity Level | MSL 3 (168 Hours) |
EPM9560WC208-20C 208-pin cqfp (ceramic quad flat pack) 핀 구성 가이드
EPM9560WC208-20C(208-pin cqfp (ceramic quad flat pack) 패키지)의 핀 구성입니다. 이 디지털 IC에는 GPIO, 통신 인터페이스(UART, SPI, I2C), 전원 핀이 포함되어 있습니다. 대체 핀 기능과 구성 옵션은 제조사 데이터시트를 참조하십시오. 임베디드 시스템 설계와 PCB 레이아웃에 필수적입니다.
다음에 대한 상세 핀아웃 데이터 없음: EPM9560WC208-20C.
다음을 참조하십시오: 데이터시트 전체 핀 구성은 다음을 참조하십시오.
일반적인 애플리케이션
EPM9560WC208-20C 적합 용도: 6 애플리케이션s: Legacy Bus Address Decoding, Industrial Control Glue Logic, Avionics and Military Backplanes, Telecom Line Card Interface, Embedded System Peripheral Bridging, Test and Measurement Equipment.
Legacy Bus Address Decoding
The EPM9560WC208-20C's 560 macrocells and 149 I/Os make it ideal for legacy address-decoding and chip-select generation on 5 V and 3.3 V buses. With 20 ns tPD, combinatorial decode paths fit within a single 33 MHz bus cycle without wait states, replacing multiple 22V10 PALs with one MAX 9000 device. The 208-pin CQFP package supplies ample I/O for 32-bit address plus control-signal decoding in VME, PCI, or Multibus backplanes, while JTAG BST enables post-assembly repair via boundary-scan. Designers should allocate a global clear pin and use the I/O pin-keeper option for un-driven bus segments.
추천
Industrial Control Glue Logic
In industrial PLC and motor-drive control boards, the EPM9560WC208-20C consolidates discrete 74-series glue logic into a single reprogrammable device. Its 3.3 V/5 V configurable I/O interfaces directly to legacy 5 V optocouplers and 3.3 V microcontrollers without external level shifters, reducing BOM and PCB area. The 35 LAB architecture supports both combinatorial and registered logic with deterministic 20 ns timing, essential for safety interlocks and encoder-quadrature decoding. Designers typically instantiate state machines, PWM modulation, and watchdog logic in one EPM9560, using JTAG BST for firmware iteration without removing the part from the field.
추천
Avionics and Military Backplanes
The ceramic CQFP-208 package of the EPM9560WC208-20C provides hermeticity and extended thermal performance valued in avionics and military systems. Combined with 560 macrocells and deterministic 20 ns timing, the part supports reliable bus arbitration, MIL-STD-1553 interface glue, and redundant-channel switching in ruggedized environments. The electrically-erasable architecture allows in-field firmware updates via JTAG, a critical feature for deployed avionics modules. Designers must derate power dissipation for high-ambient operation and use the military temperature grade (M-suffix) variants for flight hardware, but the commercial "C" variant suits ground-based military test equipment.
추천
Telecom Line Card Interface
The EPM9560WC208-20C integrates framing, alarm-collection, and timeslot-assignment logic in legacy TDM telecom line cards. Its 149 I/Os handle HDLC channelization and serial backplane interconnect, while the 20 ns tPD supports T1/E1 line-rate processing without buffering. The non-volatile EE PLD configuration provides instant-on behavior during card insertion, eliminating FPGA configuration-time transients that disrupt live traffic. Engineers typically pair the EPM9560 with an octal E1 framer and use macrocell-based state machines for per-channel alarm correlation, reducing per-card component count and improving mean-time-between-failure metrics.
추천
Embedded System Peripheral Bridging
The EPM9560WC208-20C bridges asynchronous peripheral buses (ISA, PC/104, VME) to modern processors where off-the-shelf bridge ICs are unavailable. With 560 macrocells and 149 I/Os, designers can implement custom DMA controllers, interrupt concentrators, and chip-select generators in a single device. The 5 V-tolerant I/O protects against legacy bus overshoot while 3.3 V outputs interface cleanly to modern SoCs. Designers benefit from JTAG BST for board bring-up, using the EPM9560 as both logic and boundary-scan chain terminator, shortening prototype debug cycles by allowing in-circuit visibility of bus transactions.
추천
Test and Measurement Equipment
In bench-top and ATE test instruments, the EPM9560WC208-20C provides deterministic timing for pattern generation, signal-routing matrices, and front-panel control. The 20 ns tPD supports pattern-rate generation above 25 MHz, while the 149 I/Os drive multi-channel switching matrices without external buffers. Mixed-voltage I/O (3.3 V and 5 V) lets one device bridge modern ADC/DAC logic and legacy instrument buses. Engineers value the instant-on non-volatile configuration because test equipment must boot to known state without FPGA load-time complications. JTAG BST enables production-time calibration sequences, where the EPM9560 assists in self-test stimulus generation.
추천
추천 제품 요약
엔지니어링 참조 데이터: EPM9560WC208-20C — 비교, 설계 지침 및 규정 준수 정보.
선택 가이드
대체품과의 비교
| 파라미터 | 이 제품 | EPM9560RC208-20C | EPM9560RC208-20 | EPM9560RC208-20N | EPM9560WC208-20 | EPM9560WC208-15C | EPM9560WC208-15 |
|---|---|---|---|---|---|---|---|
| Brand | Altera | Altera | Altera | Altera | Altera | Altera | Altera |
| Package | CQFP-208 (Ceramic) | RQFP-208 (Plastic Power) | RQFP-208 (Plastic Power) | RQFP-208 (Plastic Power) | CQFP-208 (Ceramic) - same | CQFP-208 (Ceramic) - same | CQFP-208 (Ceramic) - same |
| Macrocells | 560 | 560 | 560 | 560 | 560 | 560 | 560 |
| Propagation Delay (tPD) | 20 ns | 20 ns | 20 ns | 20 ns | 20 ns | 15 ns (-25%) | 15 ns (-25%) |
| User I/Os | 149 | 149 | 149 | 149 | 149 | 149 | 149 |
| Logic Array Blocks | 35 | 35 | 35 | 35 | 35 | 35 | 35 |
| Supply Voltage | 3.3 V / 5 V | 3.3 V / 5 V | 3.3 V / 5 V | 3.3 V / 5 V | 3.3 V / 5 V | 3.3 V / 5 V | 3.3 V / 5 V |
| Programming Interface | JTAG BST (ISP) | JTAG BST (ISP) | JTAG BST (ISP) | JTAG BST (ISP) | JTAG BST (ISP) | JTAG BST (ISP) | JTAG BST (ISP) |
| Temperature Grade | Commercial (0 C to +70 C) | Commercial | Commercial | Industrial (-40 C to +85 C) | Variant grade | Commercial | Variant grade |
주요 차별점
- Original ceramic CQFP-208 package for high-reliability applications (vs EPM9560RC208-20)
- Drop-in form-fit-function replacement available via Altera PDN (vs EPM9560RC208-20C)
- 560 macrocells - highest density MAX 9000 tier (vs EPM7256SQC208-10)
설계 노트
Estimated: with 560 macrocells toggling at 33 MHz on a 5.0 V supply, the EPM9560WC208-20C core current is approximately 200-300 mA per the MAX 9000 datasheet ICC-versus-frequency curves. Designers must provision one 0.1 uF X7R ceramic decoupling capacitor per VCC/GND pair, placed within 3 mm of the package leads, plus a 10 uF tantalum bulk capacitor near the supply pin. For 3.3 V VCCIO operation, ICC drops proportionally. Power-rail sequencing between VCC and VCCIO should follow the datasheet's tRAMP specification to avoid I/O latch-up during hot-plug events.
The 208-pin CQFP package has fine-pitch gull-wing leads with a typical lead pitch of 0.5 mm (1.27 mm depending on pin count variant). Land-pattern design should follow Altera's MAX 9000 reference footprint with sufficient solder-mask-defined pads to control solder joint geometry during reflow. For ceramic CQFP, the coefficient-of-thermal-expansion mismatch with FR-4 PCB requires attention to lead compliance: avoid rigid pad-to-via structures and use plated through-hole vias with thermal relief. Estimated: keep high-speed signal traces away from the exposed die area; route JTAG signals as a 4-wire daisy chain with 10K pull-ups on TCK/TMS per BSDL recommendations.
Common pitfalls with the EPM9560WC208-20C: (1) Forgetting to instantiate the JTAG chain when using boundary-scan, which leaves TCK/TMS/TDO/TDO floating and causes ISP failures. (2) Driving 5 V into a 3.3 V VCCIO configured I/O - the I/O is NOT 5 V-tolerant when VCCIO is 3.3 V. (3) Assuming the ceramic CQFP footprint matches the plastic RQFP land-pattern one-to-one - the PDN-declared form-fit-function equivalence requires PCB layout verification. (4) Not accounting for the 20 ns tPD when targeting 50 MHz bus speeds - external latches become mandatory. (5) Mistaking the part for FPGA - the EE PLD is non-volatile and instant-on, no configuration bitstream loading required.
규정 준수 정보
RoHS3 compliant per fpgalink.com distributor listing. REACH, halogen-free, and conflict-mineral declarations not enumerated in verified data - request from Intel FPGA. AEC-Q100 not applicable - this is a commercial-grade logic device, not an automotive-qualified IC.
