EPM9560RC208-20N - MAX 9000 CPLD 560 Macrocell 20ns | Intel
부품 번호: EPM9560RC208-20N ✗ 단종| 수량 | 단가 | 합계 |
|---|---|---|
| 1 | $0 | $0.00 |
| 10 | $0 | $0.00 |
| 100 | $0 | $0.00 |
| 500 | $0 | $0.00 |
| 1,000 | $0 | $0.00 |
EPM9560RC208-20N 개요
A CPLD (Complex Programmable Logic Device) is a programmable logic IC that combines the architectural flexibility of a small FPGA with the non-volatile, instant-on behavior of a PAL/GAL. In the product hierarchy, the MAX 9000 sits above simple PLDs and below FPGAs: CPLD -> programmable logic device -> digital logic IC -> semiconductor. Because configuration is stored in EEPROM cells rather than SRAM, the EPM9560RC208-20N is live at power-up with no external configuration memory, a decisive advantage in glue-logic, bus-bridging, and power-up sequencing roles.
Key differentiators of the MAX 9000 architecture include its Multiple Array MatriX (MAX) structure with 560 macrocells organized into logic array blocks, 12,000 usable gates, and 208-pin RQFP packaging that exposes up to 149 user I/O pins. The -20 speed grade guarantees a 20 ns pin-to-pin tPD, while the -20N suffix denotes the lead-free (RoHS-compatible) package variant. The device supports 5.0 V in-system programming via JTAG, allowing field reconfiguration without removing the part from the board.
Architecturally, the MAX 9000 family uses third-generation CMOS EEPROM technology with a programmable interconnect array that routes signals between logic array blocks. Each macrocell contains a flip-flop and product-term logic, enabling registered or combinatorial operation. The 20 ns propagation delay supports system clock rates in the tens of MHz for combinatorial paths, and the 5.0 V I/O is directly compatible with legacy TTL and 5 V CMOS logic families.
Typical applications include bus interface and protocol bridging, address decoding and chip-select generation, power-up sequencing and reset control, legacy system glue logic, and industrial control backplanes. The instant-on EEPROM configuration makes it especially suited to systems that cannot tolerate FPGA configuration latency.
A key design consideration is that the MAX 9000 family is a mature, legacy 5.0 V technology; new designs should evaluate modern low-voltage CPLDs, but for maintenance and drop-in replacement of existing boards the EPM9560RC208-20N remains the reference part. This page synthesizes distributor pricing, drop-in alternatives, and practical design notes not found in the manufacturer datasheet.
드롭인 대체품: EPM9560RC208-20N — 동일 패키지, 핀 호환. PCB 재작업이 필요한 다른 패키지 부품은 제외됩니다.
이 시리즈의 변형
다음과 드롭인 호환되는 동일 시리즈 모델: EPM9560RC208-20N (동일 폼 팩터 및 풋프린트) — 차이점: Package, Device Type, Process Technology, RoHS Status, Speed Grade.
빠른 비교 도구 — 나란히 비교할 대체 부품을 선택하십시오:
EPM9560RC208-20C
✅ 드롭인✓ 재고 있음
가격 문의
데이터시트 보기 →EPM9560RC208-15N
✅ 드롭인✓ 재고 있음
$19.85 / 개
데이터시트 보기 →EPM9560RC208-15
✅ 드롭인✓ 재고 있음
가격 문의
데이터시트 보기 →EPM9560RC208-20
✅ 드롭인✓ 재고 있음
가격 문의
데이터시트 보기 →EPM9560RC208-15C
✅ 드롭인✓ 재고 있음
가격 문의
데이터시트 보기 →EPM9560RC208-10N
✅ 드롭인✓ 재고 있음
$175 / 개
데이터시트 보기 →EPM9560RC208-20N 최대 정격 & 전기적 특성
| Device Family | MAX 9000 (EPM9560) |
| Macrocells | 560 |
| Usable Gates | 12,000 |
| Propagation Delay (tPD) | 20 ns |
| 패키지 | 208-pin RQFP (PowerQuad Flat Pack) |
| User I/O Pins | 149 |
| 공급 전압 | 5.0 V |
| Configuration Technology | EEPROM (non-volatile) |
| In-System Programmability | Yes, via IEEE Std. 1149.1 JTAG |
| JTAG Interface | IEEE Std. 1149.1 |
| 실장 유형 | Surface Mount |
| RoHS 상태 | Lead-free (N suffix) |
| Logic Architecture | Multiple Array MatriX (MAX), third-generation CMOS EEPROM |
| Flip-Flops | 772 (per EPM9560 series data) |
| Speed Grade | -20 (20 ns) |
EPM9560RC208-20N 208-pin rqfp (powerquad flat pack) 핀 구성 가이드
EPM9560RC208-20N(208-pin rqfp (powerquad flat pack) 패키지)의 핀 구성입니다. 이 디지털 IC에는 GPIO, 통신 인터페이스(UART, SPI, I2C), 전원 핀이 포함되어 있습니다. 대체 핀 기능과 구성 옵션은 제조사 데이터시트를 참조하십시오. 임베디드 시스템 설계와 PCB 레이아웃에 필수적입니다.
다음에 대한 상세 핀아웃 데이터 없음: EPM9560RC208-20N.
다음을 참조하십시오: 데이터시트 전체 핀 구성은 다음을 참조하십시오.
일반적인 애플리케이션
EPM9560RC208-20N 적합 용도: 6 애플리케이션s: Bus Interface and Protocol Bridging, Address Decoding and Chip-Select Generation, Power-Up Sequencing and Reset Control, Legacy System Glue Logic, Industrial Control Backplanes, Telecom and Networking Line Cards.
Bus Interface and Protocol Bridging
The EPM9560RC208-20N fits bus interface and protocol bridging because its 560 macrocells and 149 user I/O pins can implement wide address/data multiplexing and handshake logic in a single device. With a 20 ns pin-to-pin propagation delay and 5.0 V TTL/CMOS-compatible I/O, it bridges legacy 8/16-bit buses to peripherals without level shifters. The EEPROM configuration is live at power-up, so the bridge is active before the host processor releases reset, unlike SRAM-based FPGAs that need configuration time. A typical implementation places the CPLD between a host bus and a peripheral bus, using registered macrocells for synchronous handshaking; the trade-off is higher static power than modern low-voltage CPLDs, but no external configuration memory is required.
추천
Address Decoding and Chip-Select Generation
The EPM9560RC208-20N is used for address decoding and chip-select generation because its 560 macrocells provide ample product-term logic to decode wide address ranges and generate multiple active-low chip selects. The 20 ns tPD keeps decode latency low relative to legacy processor bus cycles, and the 5.0 V I/O directly drives TTL-level CS lines. Because the device is EEPROM-based, decode logic is valid immediately at power-up, which is critical for boot ROM and memory-mapped peripheral selection. Designers typically allocate one logic array block per peripheral group and use the programmable interconnect array to route decoded terms; the trade-off is that the fixed MAX 9000 interconnect is less flexible than an FPGA fabric, so decode equations should be planned to minimize cross-block routing.
추천
Power-Up Sequencing and Reset Control
The EPM9560RC208-20N suits power-up sequencing and reset control because its EEPROM configuration is instant-on, so sequencing logic is active the moment the 5.0 V rail is valid. The 560 macrocells can implement multi-rail enable sequencing, power-good gating, and reset stretching with counters and state machines, while the 149 user I/O pins drive enable pins across the board. The 20 ns tPD ensures reset de-assertion timing is deterministic. A common topology uses registered macrocells to hold peripherals in reset until all rails report good, then releases them in a defined order; the trade-off is that the CPLD itself must be powered from the earliest rail, so its supply sequencing must be considered in the power architecture.
추천
Legacy System Glue Logic
The EPM9560RC208-20N is widely used as legacy system glue logic because it consolidates dozens of discrete 74-series TTL packages into one 208-pin RQFP device. Its 560 macrocells and 12,000 usable gates absorb counters, shift registers, multiplexers, and state machines, reducing board area and part count. The 5.0 V I/O is directly compatible with legacy TTL and 5 V CMOS logic, so no level translation is needed. Because the device is non-volatile, there is no configuration PROM or boot delay. A typical migration replaces a board full of SSI/MSI logic with a single EPM9560RC208-20N; the trade-off is that the design becomes software-defined, so the JEDEC programming file must be managed and archived for production.
추천
Industrial Control Backplanes
The EPM9560RC208-20N fits industrial control backplanes because its 149 user I/O and 560 macrocells can implement backplane arbitration, slot addressing, and interrupt aggregation in one device. The 5.0 V I/O matches legacy industrial backplane signaling, and the 20 ns tPD supports deterministic response to backplane strobes. EEPROM non-volatility means the controller is ready immediately after power-up, which matters in factory automation where boot latency is unacceptable. A typical design uses the CPLD as a backplane controller that decodes slot selects and drives interrupt lines to a host CPU; the trade-off is that the MAX 9000 is a mature technology, so thermal and power budgets should account for 5.0 V static current in always-on backplanes.
추천
Telecom and Networking Line Cards
The EPM9560RC208-20N is used on telecom and networking line cards for control-plane glue logic, register interfaces, and LED/status aggregation. Its 560 macrocells implement multiple state machines for card bring-up, while the 149 user I/O pins interface to backplane control signals and local status LEDs. The 20 ns tPD supports the control-plane timing of legacy telecom buses, and 5.0 V I/O matches the signaling of older line-card backplanes. Because the device is EEPROM-based, card control logic is active at power-up without configuration from a host. A typical implementation uses the CPLD to manage card reset, slot ID, and hot-swap handshaking; the trade-off is that modern line cards favor low-voltage CPLDs, so this part is best reserved for maintenance of existing platforms.
추천
추천 제품 요약
엔지니어링 참조 데이터: EPM9560RC208-20N — 비교, 설계 지침 및 규정 준수 정보.
선택 가이드
대체품과의 비교
| 파라미터 | 이 제품 | EPM9560RC208-20C | EPM9560RC208-15N | EPM9560RC208-15 | EPM9560RC208-20 |
|---|---|---|---|---|---|
| Package | 208-pin RQFP | 208-pin RQFP - same | 208-pin RQFP - same | 208-pin RQFP - same | 208-pin RQFP - same |
| Brand | Intel | Intel | Intel | Intel | Intel |
| Propagation Delay (tPD) | 20 ns | 20 ns | 15 ns | 15 ns | 20 ns |
| Macrocells | 560 | 560 | 560 | 560 | 560 |
| Usable Gates | 12,000 | 12,000 | 12,000 | 12,000 | 12,000 |
| Supply Voltage | 5.0 V | 5.0 V | 5.0 V | 5.0 V | 5.0 V |
| Lead-Free (RoHS) | Yes (N suffix) | No (C suffix) | Yes (N suffix) | No | No |
| Configuration Technology | EEPROM (non-volatile) | EEPROM (non-volatile) | EEPROM (non-volatile) | EEPROM (non-volatile) | EEPROM (non-volatile) |
| JTAG ISP | Yes (IEEE Std. 1149.1) | Yes (IEEE Std. 1149.1) | Yes (IEEE Std. 1149.1) | Yes (IEEE Std. 1149.1) | Yes (IEEE Std. 1149.1) |
| User I/O Pins | 149 | 149 | 149 | 149 | 149 |
주요 차별점
- Lead-free RoHS-compatible package variant (vs EPM9560RC208-20C)
- 20 ns speed grade with 560 macrocells (vs EPM9560RC208-15N)
- EEPROM instant-on configuration (vs EPM9560RC208-10N)
설계 노트
The EPM9560RC208-20N is a 5.0 V EEPROM-based CPLD and draws static supply current even when logic is idle. Estimated: budget the 5.0 V rail for the device's quiescent and dynamic current, and decouple each VCC pin with a 0.1 uF ceramic capacitor placed within a few millimeters of the pin, plus a bulk 10 uF capacitor per device. Because the part is non-volatile, there is no configuration inrush, but the 5.0 V rail must be monotonic during power-up to guarantee correct EEPROM initialization.
Route the IEEE Std. 1149.1 JTAG signals (TCK, TMS, TDI, TDO) as short, controlled-impedance traces and keep TCK away from noisy switching nodes. Terminate TDI and TMS appropriately and provide a stable JTAG header for in-system programming. Place the 208-pin RQFP on a board with adequate thermal relief and keep the ground plane continuous under the device to minimize return-path inductance on the 149 user I/O lines.
A common pitfall with the EPM9560RC208-20N is assuming SRAM-FPGA-like flexibility: the MAX 9000 programmable interconnect array is fixed, so logic placement across logic array blocks affects achievable timing. Estimated: if a critical path crosses multiple blocks, the effective delay can exceed the 20 ns tPD specification. Plan decode and state-machine equations to localize logic within blocks, and verify timing with the vendor fitter report before committing the JEDEC file to production.
규정 준수 정보
The N suffix denotes the lead-free (RoHS-compatible) package variant. REACH, halogen-free, and conflict-minerals status were not stated in the provided data.