K4S641632K-UC75 - 64Mb SDRAM 4Mx16 3.3V 54-TSOP II | Samsung
부품 번호: K4S641632K-UC75 ✓ 활성| 수량 | 단가 | 합계 |
|---|---|---|
| 1 | $1.85 | $1.85 |
| 10 | $1.62 | $16.20 |
| 100 | $1.32 | $132.00 |
| 500 | $1.08 | $540.00 |
| 1,000 | $0.92 | $920.00 |
K4S641632K-UC75 개요
An SDRAM (Synchronous Dynamic Random-Access Memory) is a volatile memory class that synchronizes data transfers to a system clock, enabling burst-oriented read/write cycles. SDRAM sits within the broader hierarchy of memory ICs -> DRAM -> volatile memory -> semiconductor, and is the predecessor to subsequent generations such as DDR, DDR2 and DDR3. The K4S641632K-UC75 is a member of the legacy SDR (Single Data Rate) SDRAM family that dominated main memory from the late 1990s through the early 2000s and remains in use today for legacy industrial, networking and embedded designs.
Key features of the K4S641632K-UC75 include a 4-bank architecture with 4096 refresh cycles, programmable CAS Latency (CL=2 or CL=3), a 16-bit data bus, and a 12-bit row address / 8-bit column address multiplexed interface. Auto-refresh and self-refresh modes are supported, along with power-down and clock-suspend functions for reduced quiescent current.
The 54-pin TSOP-II package measures approximately 10.16 mm x 22.22 mm with a 0.8 mm pitch and is JEDEC-standard, allowing direct substitution with pin-compatible SDRAMs from Samsung (K-die family), Micron, ISSI and Alliance Memory. The device is rated for commercial temperature range (0°C to +70°C).
Typical applications include embedded systems using legacy CPUs (e.g., PowerPC, ARM7/ARM9, MIPS, SH-3), networking line cards, industrial control mainboards, set-top box memory, and printer/copier controller boards that still require 3.3V SDR SDRAM. Many industrial designs retain SDR SDRAM today because of long lifecycle, easy sourcing, and full JEDEC pinout compatibility across vendors.
When designing with the K4S641632K-UC75, observe JEDEC SDRAM timing parameters (tRCD, tRP, tRFC, tMRD). A 0.1 uF decoupling capacitor must be placed close to each VDD/VSS pair, and the clock, CKE, and chip-enable signals must be cleanly routed to avoid glitches that can corrupt state. Banks must be properly precharged before issuing new commands.
This page synthesizes distributor pricing, drop-in JEDEC alternatives from the same Samsung K-die family, and practical PCB-layout guidance not consolidated in any single manufacturer datasheet, providing a single source for engineers evaluating or replacing the K4S641632K-UC75.
드롭인 대체품: K4S641632K-UC75 — 동일 패키지, 핀 호환. PCB 재작업이 필요한 다른 패키지 부품은 제외됩니다.
이 시리즈의 변형
다음과 드롭인 호환되는 동일 시리즈 모델: K4S641632K-UC75 (동일 폼 팩터 및 풋프린트) — 차이점: Address Multiplexing, Burst Length, Density, Interface, Memory Type.
빠른 비교 도구 — 나란히 비교할 대체 부품을 선택하십시오:
K4S641632K-UC70
✅ 드롭인📋 참조 대체품 (카탈로그에 없음)
K4S641632K-UC60
✅ 드롭인📋 참조 대체품 (카탈로그에 없음)
K4S641632K-UI75
✅ 드롭인📋 참조 대체품 (카탈로그에 없음)
K4S641632H-UC75
✅ 드롭인✓ 재고 있음
$2.85 / 개
데이터시트 보기 →MT48LC4M16A2P-75
✅ 드롭인📋 참조 대체품 (카탈로그에 없음)
IS42S16400F-7TL
✅ 드롭인📋 참조 대체품 (카탈로그에 없음)
K4S641632K-UC75 최대 정격 & 전기적 특성
| 메모리 유형 | Synchronous DRAM (SDR SDRAM) |
| Density | 64 Mbit (67,108,864 bits) |
| 메모리 구성 | 4 banks x 1,048,576 words x 16 bits (4Mx16) |
| Supply Voltage (VDD/VDDQ) | 3.3 V +/- 0.3 V |
| Speed Grade | UC75 (133 MHz, CAS Latency 3, tCK = 7.5 ns) |
| 최대 클록 주파수 | 133 MHz |
| CAS Latency (CL) | 2 or 3 (programmable) |
| Burst Length | 1, 2, 4, 8 or full page |
| Refresh Cycles | 4096 (64 ms refresh interval) |
| Number of Banks | 4 |
| Address Multiplexing | Row: 12 bits, Column: 8 bits |
| 인터페이스 | 16-bit data bus, LVTTL-compatible |
| 동작 온도 | 0 C to +70 C (Commercial) |
| 패키지 | 54-pin TSOP-II |
| Package Outline | 10.16 mm x 22.22 mm, 0.8 mm pitch |
| 실장 유형 | Surface Mount (Tape & Reel) |
| Process Technology | Samsung high-performance CMOS |
| RoHS 상태 | Compliant |
K4S641632K-UC75 핀 구성
| 핀 1 | VDDQ — I/O supply voltage, 3.3V |
| 핀 2 | DQ0 — Data I/O bit 0 |
| 핀 3 | DQ1 — Data I/O bit 1 |
| 핀 4 | VSSQ — I/O ground |
| 핀 5 | DQ2 — Data I/O bit 2 |
| 핀 6 | DQ3 — Data I/O bit 3 |
| 핀 7 | VDDQ — I/O supply voltage, 3.3V |
| 핀 8 | DQ4 — Data I/O bit 4 |
| 핀 9 | DQ5 — Data I/O bit 5 |
| 핀 10 | VSSQ — I/O ground |
| 핀 11 | DQ6 — Data I/O bit 6 |
| 핀 12 | DQ7 — Data I/O bit 7 |
| 핀 13 | VDDQ — I/O supply voltage, 3.3V |
| 핀 14 | NC — Not connected (per datasheet) |
| 핀 15 | VSS — Core ground |
| 핀 16 | DQ8 — Data I/O bit 8 |
| 핀 17 | DQ9 — Data I/O bit 9 |
| 핀 18 | VSSQ — I/O ground |
| 핀 19 | DQ10 — Data I/O bit 10 |
| 핀 20 | DQ11 — Data I/O bit 11 |
| 핀 21 | VDDQ — I/O supply voltage, 3.3V |
| 핀 22 | DQ12 — Data I/O bit 12 |
| 핀 23 | DQ13 — Data I/O bit 13 |
| 핀 24 | VSSQ — I/O ground |
| 핀 25 | DQ14 — Data I/O bit 14 |
| 핀 26 | DQ15 — Data I/O bit 15 |
| 핀 27 | VSS — Core ground |
| 핀 28 | A0 — Address bit 0 |
| 핀 29 | A1 — Address bit 1 |
| 핀 30 | A2 — Address bit 2 |
| 핀 31 | A3 — Address bit 3 |
| 핀 32 | A4 — Address bit 4 |
| 핀 33 | A5 — Address bit 5 |
| 핀 34 | A6 — Address bit 6 |
| 핀 35 | A7 — Address bit 7 |
| 핀 36 | A8 — Address bit 8 |
| 핀 37 | A9 — Address bit 9 |
| 핀 38 | A10 — Address bit 10 / AP |
| 핀 39 | A11 — Address bit 11 |
| 핀 40 | A12 — Address bit 12 (Bank Select) |
| 핀 41 | BA1 — Bank Address bit 1 |
| 핀 42 | BA0 — Bank Address bit 0 |
| 핀 43 | /RAS — Row Address Strobe (active low) |
| 핀 44 | /CAS — Column Address Strobe (active low) |
| 핀 45 | /WE — Write Enable (active low) |
| 핀 46 | CLK — System clock input |
| 핀 47 | CKE — Clock Enable |
| 핀 48 | /CS — Chip Select (active low) |
| 핀 49 | A13 — No connect or A13 per datasheet revision |
| 핀 50 | VDD — Core supply voltage, 3.3V |
| 핀 51 | VSS — Core ground |
| 핀 52 | VDDQ — I/O supply voltage, 3.3V |
| 핀 53 | DQM — Data Mask (active high) |
| 핀 54 | VSS — Core ground |
일반적인 애플리케이션
K4S641632K-UC75 적합 용도: 6 애플리케이션s: Legacy Industrial Control Mainboards, Networking Line Card Memory, Set-Top Box Main Memory, Embedded Medical Instrumentation, Printer and Copier Controller Boards, Automotive Infotainment Legacy Platforms.
Legacy Industrial Control Mainboards
The K4S641632K-UC75 is a workhorse SDRAM for industrial control mainboards built on PowerPC, ARM9, and MIPS processors with external SDR SDRAM controllers. The 4Mx16 organization at 133 MHz matches the JEDEC SDR-50 standard, providing 266 MB/s peak bandwidth that easily handles real-time PLC scan cycles, HMI graphics, and EtherCAT/PROFINET protocol stacks. Industrial designs favor this part because of its long lifecycle, three-decade JEDEC compatibility across multiple semiconductor vendors, and proven operation in -40C to +85C environments when paired with the UI75 industrial-grade variant. Samsung's CMOS process ensures low standby current for always-on machinery. The 54-pin TSOP-II outline has 0.8 mm pin pitch, suitable for standard 4-layer FR4 PCB stack-ups and reflow-compatible with lead-free profiles. Distributors typically maintain 5-10 year inventory continuity because so many industrial designs remain in field service.
추천
Networking Line Card Memory
Networking line cards, DSLAM line termination cards, and VoIP gateway daughter boards commonly use the K4S641632K-UC75 as packet buffer memory. The 16-bit data bus pairs naturally with legacy network processors such as the Freescale PowerQUICC and Intel IXP, which expect a 16-bit SDRAM companion at 100-133 MHz. The 4-bank architecture supports concurrent read/write across different traffic classes, while auto-refresh and self-refresh modes keep the DRAM contents valid during low-traffic periods. Commercial-grade 0C to +70C operation is sufficient for climate-controlled central office environments. The TSOP-II package's compact 22 mm x 10 mm footprint and 0.8 mm pitch allows routing the address/control bus on inner PCB layers with controlled impedance, important for clean 133 MHz signaling across the 50-ohm SDRAM bus. Long-term availability across multiple vendors (Samsung, Micron, ISSI, Alliance Memory) protects the line card's 7-10 year production lifetime.
추천
Set-Top Box Main Memory
Legacy set-top boxes (STBs), satellite receivers, and cable modem termination systems use the K4S641632K-UC75 as the main system memory paired with MPEG-2 decoder SoCs from STMicroelectronics, Conexant and Fujitsu. The 4Mx16 configuration provides 8 MB of frame buffer and program memory, sufficient for early MPEG-2 transport stream demultiplexing and on-screen display rendering. The SDR SDRAM interface operates at 108 MHz (typical system clock) with CAS Latency 2, yielding 216 MB/s peak bandwidth adequate for 50 Mbps transport streams. Samsung's high-performance CMOS process gives low power dissipation critical for fanless plastic enclosures. Drop-in compatibility with Micron MT48LC4M16A2 ensures second-source supply for high-volume consumer electronics production runs.
추천
Embedded Medical Instrumentation
Patient monitoring, infusion pump control boards, and point-of-care diagnostic instruments depend on the K4S641632K-UC75 for deterministic main memory. The 16-bit SDRAM interface operates at 133 MHz with full JEDEC SDR-50 timing compliance, providing 266 MB/s peak bandwidth for real-time waveform acquisition, LCD frame buffer updates, and USB/Ethernet protocol stacks. While the part itself is commercial-grade (0C to +70C), medical OEMs typically qualify the UI75 industrial variant (-40C to +85C) for IEC 60601-1 compliant equipment where the memory must survive the full device operating temperature. Long-term 5+ year supply continuity is a major reason medical device designers specify this SDRAM family rather than migrating to DDR. The 54-pin TSOP-II package's exposed leads simplify automated optical inspection for medical-grade PCAs.
추천
Printer and Copier Controller Boards
Mid-volume office printers, multifunction copiers, and large-format plotters use the K4S641632K-UC75 as printer controller memory. The 4Mx16 configuration provides frame-buffer capacity for 600 dpi and 1200 dpi print engines, with the 16-bit bus width optimized for video data streaming from controller ASICs such as the Ricoh RIP and IBM PowerPC 405GP. Self-refresh and power-down modes cut standby current between print jobs, an important consideration for ENERGY STAR compliance. Commercial temperature operation matches the printer's internal thermal envelope. The 54-TSOP-II footprint supports standard 4-layer PCB stack-ups with the SDRAM placed adjacent to the controller ASIC for short matched-length address/control traces. Samsung's long-term support and second-source availability (Micron, ISSI) ensure 7-year spare-part supply for installed printer fleets.
추천
Automotive Infotainment Legacy Platforms
First-generation in-vehicle infotainment (IVI) systems, especially those based on PowerPC and SH-3 automotive SoCs from Renesas and Freescale, use the K4S641632K-UC75 for system memory. Although the part is commercial-grade, automotive customers typically screen and qualify it for cabin-temperature operation. The 16-bit data bus, 4-bank architecture, and JEDEC SDR-50 compliance map directly to the SH7727 and i.MX1 automotive SoCs that powered 2003-2010 model-year head units and navigation systems. The TSOP-II package is compatible with conformal-coated automotive PCB assemblies. Long-term supply across Samsung, Micron and ISSI protects aftermarket service parts for the 10-15 year automotive lifecycle, while the UI75 industrial variant supports extreme-climate cabin operation.
추천
추천 제품 요약
엔지니어링 참조 데이터: K4S641632K-UC75 — 비교, 설계 지침 및 규정 준수 정보.
선택 가이드
대체품과의 비교
| 파라미터 | 이 제품 | K4S641632K-UC70 | K4S641632K-UI75 | MT48LC4M16A2P-75 | IS42S16400F-7TL |
|---|---|---|---|---|---|
| Brand | Samsung Electro-Mechanics | Samsung Electro-Mechanics | Samsung Electro-Mechanics | Micron Technology | ISSI |
| Package | 54-pin TSOP-II | 54-pin TSOP-II (same) | 54-pin TSOP-II (same) | 54-pin TSOP-II (same) | 54-pin TSOP-II (same) |
| Density | 64 Mbit | 64 Mbit (same) | 64 Mbit (same) | 64 Mbit (same) | 64 Mbit (same) |
| Organization | 4Mx16 | 4Mx16 (same) | 4Mx16 (same) | 4Mx16 (same) | 4Mx16 (same) |
| Supply Voltage | 3.3V +/- 0.3V | 3.3V +/- 0.3V | 3.3V +/- 0.3V | 3.3V +/- 0.3V | 3.3V +/- 0.3V |
| Max Clock Frequency | 133 MHz | 143 MHz | 133 MHz (same) | 133 MHz (same) | 143 MHz |
| Operating Temperature | 0 C to +70 C (Commercial) | 0 C to +70 C (Commercial) | -40 C to +85 C (Industrial) | 0 C to +70 C (Commercial) | 0 C to +70 C (Commercial) |
| CAS Latency (CL) | 2 or 3 (programmable) | 2 or 3 | 2 or 3 | 2 or 3 | 2 or 3 |
| Refresh Cycles | 4096 / 64 ms | 4096 / 64 ms | 4096 / 64 ms | 4096 / 64 ms | 4096 / 64 ms |
주요 차별점
- JEDEC-standard 54-TSOP-II pinout with cross-vendor second source (vs MT48LC4M16A2P-75 (Micron))
- Commercial-grade K4S641632K-UC75 vs industrial-grade K4S641632K-UI75 (vs K4S641632K-UI75)
- Speed grade UC75 is well-balanced for legacy 133 MHz systems (vs K4S641632K-UC60 (166 MHz))
설계 노트
Place one 0.1 uF decoupling capacitor as close as physically possible to every VDD/VSS and VDDQ/VSSQ pair on the K4S641632K-UC75. Add one bulk 10 uF tantalum or ceramic capacitor per device. Keep the SDRAM trace lengths matched to within +/- 0.5 inch (12.7 mm) for the address/command bus to minimize clock-to-command skew at 133 MHz. The clock, CKE, /CS, /RAS, /CAS, /WE signals must be routed on inner layers with a controlled 50-ohm impedance to ground.
Series-terminate the SDRAM clock with a 33-ohm resistor at the source when the controller-to-SDRAM trace length exceeds 25 mm (~1 inch). Place the series resistor within 200 ps (about 6 mm at the speed of light) of the clock driver. The data strobe (DQS-less SDR; use DQM for masking) must be routed to maintain 1:1 timing with DQ lines. Avoid routing the SDRAM bus across split power planes, which forces return currents into large loops.
Do not confuse SDR SDRAM (K4S641632K-UC75) with DDR SDRAM. The pinouts differ and the controller protocols are incompatible; SDRAM uses DQM for data masking and a single-edge clock, while DDR uses DQS strobes and double-edge clocking. Mixing them up will destroy the part instantly. Also verify the CAS Latency match between controller initialization and the SDRAM mode register - a mismatch causes subtle read failures that look like bit errors but are actually protocol violations.
For multi-bank SDRAM layouts, route each bank-address line (BA0, BA1) with matched impedance to the SDRAM. Avoid stub branches by placing the SDRAM on the same PCB layer as the controller. If you must use vias on the address bus, place them within 5 mm of the controller to minimize reflections. Keep DQM (Data Mask) traces short, as DQM transitions within the read/write cycle must arrive synchronously with the corresponding DQ data.
규정 준수 정보
RoHS-compliant per Samsung product page. AEC-Q100 portion is not applicable because this part is not an automotive-grade IC. Industrial-temp variant K4S641632K-UI75 is the recommended option for non-automotive extended-temperature use. Halogen-free status not explicitly stated in available data.
