Analog Devices

MAX3381EEUP+T - 2/2 RS-232 Transceiver | Analog Devices

부품 번호: MAX3381EEUP+T ✓ 활성
+2.35 V to +5.5 V Vdss 1 µA Id 20-pin TSSOP Package
MOQ: 1 |

MAX3381EEUP+T 개요

Analog Devices MAX3381EEUP+T is a 2-transmitter, 2-receiver RS-232 transceiver operating from +2.35 V to +5.5 V, with 15 kV ESD protection on I/O and logic pins, in a 20-pin TSSOP package. The interface supports EIA/TIA-232 and V.28/V.24 communication while operating from a low 1 µA supply current.

An RS-232 transceiver is an interface IC that converts low-voltage digital logic signals into RS-232 voltage levels and converts received RS-232 signals back into logic-compatible levels. It belongs to the transceiver and driver/receiver hierarchy, bridging UART, UART-compatible controller, and computer I/O logic with external serial cables. This bidirectional level-shifting function allows a compact system to communicate through a longer-distance, noise-tolerant serial interface.

The MAX3381EEUP+T provides two transmit channels and two receive channels, supporting full-duplex point-to-point serial links. Its +2.35 V to +5.5 V operating range supports low-voltage logic systems as well as conventional +5 V equipment. The manufacturer's product page identifies 15 kV ESD protection on both I/O and logic pins, helping protect sensitive interface circuits when cables are connected or disconnected.

The MAX3380E and MAX3381E families combine low power consumption with high data-rate capability. The MAX3381E variant is specified for production availability, and its enhanced ESD protection applies to both the RS-232 side and the logic pins. Independent transmit and receive channels allow full-duplex operation when the connected system assigns one driver and one receiver to each communication path.

Typical uses include industrial control links, point-of-sale equipment, data-cable interfaces, instrumentation, and embedded serial ports. The dual transmitter arrangement can support two outbound RS-232 signals, while the dual receivers can monitor two incoming signals. In designs using a UART, the device can translate between the controller's logic-level pins and the voltage levels required by an RS-232 cable.

When laying out the circuit, place the device close to the RS-232 connector and route driver and receiver traces away from sensitive analog or high-speed digital paths. Verify the connector's signal and ground assignments, provide the required supply bypassing, and maintain adequate board spacing to reduce surge-current exposure at the protected pins.

This product page brings together the manufacturer's core electrical characteristics, package information, verified drop-in relationships, and practical interface-layout guidance. It is intended to help engineers evaluate the MAX3381EEUP+T for low-voltage RS-232 links, compare documented replacements, and plan protection and layout before releasing a PCB design.

드롭인 대체품: MAX3381EEUP+T — 동일 패키지, 핀 호환. PCB 재작업이 필요한 다른 패키지 부품은 제외됩니다.

이 시리즈의 변형

다음과 드롭인 호환되는 동일 시리즈 모델: MAX3381EEUP+T (동일 폼 팩터 및 풋프린트) — 차이점: Interface Standard, Package, Supply Voltage Range.

Analog Devices
Interface Standard: EIA/TIA-232
Package: 20-TSSOP
Supply Voltage Range: 2.35V to 5.5V
비교 대상: MAX3381EEUP+T →

MAX3381EEUP+

✅ 드롭인
Analog Devices
📦 20-pin TSSOP
RS-232 transceiver interface IC · 2 transmitters · 2 receivers · +2.35 V to +5.5 V · 1 uA · 460 kbps · ±15 kV · ±15 kV

가격 문의

데이터시트 보기 →

MAX3381ECUP+

✅ 드롭인
Analog Devices
📦 20-pin TSSOP
RS-232 transceiver · 2 · 2 · +2.35 V to +5.5 V · 1 A · EIA/TIA-232 · V.28/V.24 · 15 kV

가격 문의

데이터시트 보기 →

MAX3381EEUP+T 사양

Transceiver Configuration 2 Transmitter / 2 Receiver
Supply Voltage Range +2.35 V to +5.5 V
공급 전류 1 µA
ESD Protection on I/O Pins ±15 kV
ESD Protection on Logic Pins ±15 kV
Interface Standard EIA/TIA-232, V.28 and V.24
핀 수 20 pins
패키지 20-pin TSSOP
실장 유형 Surface Mount

MAX3381EEUP+T 20-pin tssop 핀 구성 가이드

MAX3381EEUP+T(20-pin tssop 패키지)의 핀 구성입니다. 핀 번호, 기능, 연결 다이어그램은 제조사 데이터시트에 정의되어 있습니다. 정확한 풋프린트와 솔더링 지침은 해당 문서를 참조하십시오.

MAX3381EEUP+T의 20-pin tssop 패키지 핀아웃 다이어그램

다음에 대한 상세 핀아웃 데이터 없음: MAX3381EEUP+T.

다음을 참조하십시오: 데이터시트 전체 핀 구성은 다음을 참조하십시오.

일반적인 애플리케이션

MAX3381EEUP+T 적합 용도: 6 애플리케이션s: Low-Voltage Embedded Serial Port, Industrial Control Console, Point-of-Sale Equipment, Data Cable Interface, Instrumentation and Measurement, Peripheral and Sensor Gateway.

🔧

Low-Voltage Embedded Serial Port

The MAX3381EEUP+T fits a compact embedded controller that needs to communicate through a conventional RS-232 connection without a +5 V-only interface. Its +2.35 V to +5.5 V operating range allows direct operation from suitable low-voltage system rails, while the two transmitters and two receivers support separate outbound and inbound paths. The 1 µA supply-current specification is valuable in power-sensitive equipment. Place the transceiver near the serial connector, provide the required local bypass capacitance, and route the logic-side traces away from the higher-voltage RS-232 outputs.

🏭

Industrial Control Console

The MAX3381EEUP+T can bridge a controller-based industrial console to an RS-232 service interface because it provides two transmitters and two receivers for full-duplex communication. Its +2.35 V to +5.5 V supply range accommodates low-voltage logic domains, and ±15 kV protection on both I/O and logic pins strengthens the interface against electrostatic discharge. The designer should still verify the exact temperature grade, connect a protective ground near the cable entry, and keep switching-node and high-current traces away from the transceiver footprint.

🖥️

Point-of-Sale Equipment

The MAX3381EEUP+T is suitable for point-of-sale equipment that needs more than one RS-232 direction in a limited board area. Two transmitter channels can address separate peripherals while two receiver channels can accept return or status information, reducing the need for multiple interface packages. Its low 1 µA supply current supports compact systems with limited standby power, while the 20-pin TSSOP package simplifies routing to a conventional surface-mount design. Validate connector pin assignments and logic levels in the system schematic before fabrication.

🌐

Data Cable Interface

The MAX3381EEUP+T is designed for data-cable applications that require logic-to-RS-232 conversion in both directions. Two transmitter outputs and two receiver inputs allow two cable-facing channels, and the +2.35 V to +5.5 V range supports systems using either low-voltage or +5 V supplies. The interface's ±15 kV ESD rating on cable-side and logic-side pins supports robust connector integration, but engineers should still apply chassis grounding and verify that the selected connector exposes the intended signals.

📺

Instrumentation and Measurement

The MAX3381EEUP+T can provide the RS-232 interface between a measurement instrument and a host computer. The two receivers permit two incoming measurements or status signals, while the two transmitters support command or control outputs. Low 1 µA supply current is beneficial in portable or intermittently powered instruments, and the 20-pin TSSOP package preserves board area. Confirm the operating temperature range, supply sequencing, and connector grounding for the specific instrument enclosure and cable length.

🧩

Peripheral and Sensor Gateway

The MAX3381EEUP+T can connect a gateway board to legacy RS-232 sensors or peripheral controllers while keeping the host logic rail within the +2.35 V to +5.5 V operating range. Its dual-channel architecture supports separate command and telemetry paths, and the low supply current assists battery- or sensor-oriented designs. For installations with long cables, use the protected transceiver at the connector edge, maintain a solid ground path, and confirm that surge and ESD requirements are handled at the system level.

What is the MAX3381EEUP+T?
The MAX3381EEUP+T is a 2-transmitter, 2-receiver RS-232 transceiver from Analog Devices. It operates from +2.35 V to +5.5 V, draws 1 µA supply current, and provides ±15 kV ESD protection on I/O and logic pins. According to the manufacturer product page, the device is intended for EIA/TIA-232 and V.28/V.24 communication interfaces in a 20-pin TSSOP package.
What are the key specifications of MAX3381EEUP+T that engineers should know?
The MAX3381EEUP+T combines two RS-232 transmitters, two receivers, a +2.35 V to +5.5 V supply range, and ±15 kV ESD protection in a 20-pin TSSOP package. According to the Analog Devices product page, its supply current is 1 µA and it supports EIA/TIA-232, V.28, and V.24 interfaces. These characteristics make it relevant to compact, low-power, full-duplex serial links.
What is the operating voltage of MAX3381EEUP+T?
The MAX3381EEUP+T operates from +2.35 V to +5.5 V. According to the Analog Devices MAX3381E product page, this range supports low-voltage logic systems as well as conventional +5 V equipment. The logic-side interface remains compatible with the EIA/TIA-232, V.28, and V.24 communication standards named by the manufacturer.
Where can I download the MAX3381EEUP+T datasheet PDF?
The MAX3381EEUP+T datasheet PDF is available through the manufacturer-linked document hosted by DiGi Electronics. Use the product documentation to confirm the complete electrical-characteristics table, pin description, timing information, and recommended application circuit before finalizing the PCB. The Analog Devices product page also links the device's current technical documentation and product-selection information.
Where can I find the MAX3381EEUP+T pinout?
The MAX3381EEUP+T pinout is defined in the manufacturer's 20-pin TSSOP pin-description table and package drawing. Use that table when assigning the two transmit inputs, two transmit outputs, two receive inputs, two receive outputs, supply, ground, and any shutdown or enable functions. The package outline and pin numbering should be checked against the selected TSSOP footprint before release.
What is the best drop-in replacement for MAX3381EEUP+T?
The MAX3381ECUP+ is the strongest documented drop-in candidate for MAX3381EEUP+T because a component comparison identifies it as a complete replacement with consistent terminals, package, and functional characteristics. A cross-brand replacement was not established from the available manufacturer and distributor information. Confirm temperature grade, ESD rating, supply range, and production status against the current datasheet before substitution.
Can MAX3381ECUP+ replace MAX3381EEUP+T?
Yes, MAX3381ECUP+ is documented as a complete replacement for MAX3381EEUP+T because its terminals, package, and principal performance characteristics are consistent. Review the manufacturer datasheet for the exact ordering-temperature and qualification requirements before approving the change. No PCB modification should be necessary when the specified 20-pin TSSOP footprint is used.
When should I choose MAX3381EEUP+T over MAX3381EEUP+?
Choose MAX3381EEUP+T when the specified temperature-grade suffix and extended operating range are required by the equipment environment. Choose MAX3381EEUP+ when the commercial-temperature grade is acceptable and procurement preference favors that ordering code. Both use a 20-pin TSSOP package and the same 2/2 RS-232 architecture, so the final choice should follow the temperature requirements in the datasheet.
Is MAX3381EEUP+T suitable for industrial serial communication?
The MAX3381EEUP+T is suitable for industrial serial interfaces when its documented temperature range, ESD protection, and supply limits satisfy the equipment specification. Its +2.35 V to +5.5 V operating range supports low-voltage system rails, while ±15 kV ESD protection is available on both I/O and logic pins. Confirm the exact temperature grade and system-level isolation requirements before installation.
Does MAX3381EEUP+T support full-duplex RS-232 communication?
Yes, the MAX3381EEUP+T includes two transmitters and two receivers, allowing two simultaneous outbound RS-232 signals and two inbound signal paths. The manufacturer's product page identifies it as a 2Tx/2Rx communication interface. This arrangement suits full-duplex point-to-point links, provided the connected UART and cable assignment use the corresponding transmitter and receiver channels.
How much ESD protection does MAX3381EEUP+T provide?
The MAX3381EEUP+T provides ±15 kV ESD protection on its I/O pins and ±15 kV ESD protection on its logic pins. According to the Analog Devices product page, this protection applies to both sides of the interface rather than only the external cable side. It reduces interface vulnerability but does not replace normal connector grounding or cable-management practices.
Where can I buy MAX3381EEUP+T online?
Use the Request a Quote form on this page to request current MAX3381EEUP+T pricing, stock confirmation, and lead time for the exact 20-pin TSSOP ordering code. The listing should identify the 2/2 RS-232 configuration and +2.35 V to +5.5 V operating range. Confirm the requested package, temperature suffix, and quantity before placing a production order.
What is the price of MAX3381EEUP+T?
The current price of MAX3381EEUP+T is obtained through the Request a Quote form on this page. Submit the required quantity, package, and delivery information so procurement can return a current quotation for the exact MAX3381EEUP+T ordering code. This avoids relying on a starting price that may represent a different package or quantity condition.
What is the lead time for MAX3381EEUP+T?
The current lead time and minimum order quantity for MAX3381EEUP+T should be confirmed through the Request a Quote form on this page. Include the production quantity, reel format, delivery location, and required schedule in the request. The manufacturer lists the MAX3381E family as production, but exact availability can change with demand and packaging requirements.
Is MAX3381EEUP+T in stock?
Stock for MAX3381EEUP+T should be confirmed through the Request a Quote form on this page, where the exact ordering code and required quantity can be reviewed. The manufacturer identifies the MAX3381E family as production, but that status alone does not guarantee a specific quantity is immediately available. Submit the reel quantity and delivery schedule for an inventory response.

엔지니어링 참조 데이터: MAX3381EEUP+T — 비교, 설계 지침 및 규정 준수 정보.

선택 가이드

Choose MAX3381EEUP+T when a production design requires a 2Tx/2Rx RS-232 interface, a +2.35 V to +5.5 V supply range, and ±15 kV ESD protection in a 20-pin TSSOP package. MAX3381EEUP+ is appropriate when its ordering-temperature grade satisfies the equipment environment and procurement prefers that suffix. MAX3381ECUP+ is useful for a documented drop-in redesign because its terminals, package, and principal functional characteristics are consistent. In every case, confirm the exact temperature grade, maximum data rate, shutdown behavior, and supply-decoupling requirements against the current manufacturer datasheet. No cross-brand replacement should be approved solely from a generic similarity listing; it must first demonstrate the same 20-pin footprint, compatible logic levels, adequate data rate, and suitable ESD and temperature ratings.

대체품과의 비교

파라미터 이 제품 MAX3381EEUP+ MAX3381ECUP+
Package 20-pin TSSOP 20-pin TSSOP 20-pin TSSOP
Brand Analog Devices Analog Devices Analog Devices
Transceiver Configuration 2Tx/2Rx 2Tx/2Rx 2Tx/2Rx

주요 차별점

  • Supports lower-voltage logic systems (vs MAX3381EEUP+)
  • Documented complete replacement path (vs MAX3381ECUP+)
  • Full-duplex channel count in one package (vs MAX3381EEUP+)

설계 노트

Place the MAX3381EEUP+T close to the RS-232 connector and route the cable-side driver traces as short as practical. Keep logic-side traces away from the transmit outputs, and provide a low-impedance ground path between the connector ground, transceiver ground, and circuit ground. This arrangement limits transient-current loop area and helps the ±15 kV-protected pins remain effective during cable events.

Use the manufacturer's recommended supply-bypass configuration and place the bypass capacitor adjacent to the device supply pin. The device operates from +2.35 V to +5.5 V, so the system rail must remain inside that interval during startup, communication activity, and fault recovery. Confirm that ground bounce or connector transients do not pull the local supply outside the permitted operating range.

Do not treat the logic-side pins as additional RS-232 outputs merely because they receive ESD protection. Verify every transmitter input, transmitter output, receiver input, receiver output, supply, and ground assignment against the current pin-description table before routing the PCB. Also confirm the operating-temperature suffix of any replacement so a board intended for extended-temperature use is not populated with a commercial-temperature ordering code.

규정 준수 정보

RoHS
Unknown
REACH
Unknown
AEC-Q100
Not Applicable
무연
Unknown
무할로겐
Unknown
분쟁 광물
Unknown

The MAX3381E family is listed as production by Analog Devices, but no specific RoHS, REACH, lead-free, halogen-free, conflict-minerals, or automotive qualification declaration appears in the available product information.

데이터 검증일: 2026-11-09 — XAIPART 부품 엔지니어링 팀이 검증하고 관리한 데이터

관련 검색

MAX3381EEUP+T MAX3381EEUP+T datasheet MAX3381EEUP+T datasheet pdf MAX3381EEUP+T pinout MAX3381EEUP+T replacement MAX3381EEUP+T equivalent MAX3381EEUP+T cross reference MAX3381EEUP+T price MAX3381EEUP+T stock Analog Devices MAX3381EEUP+T MAX3381EEUP+T vs MAX3381ECUP+ MAX3381EEUP+T 20 pin TSSOP

관련 부품 & 용어

Analog Devices MAX3381EEUP+T MAX3381EEUP+ MAX3381ECUP+ MAX3381E MAX3380E RS-232 EIA/TIA-232 V.28 V.24 RS-232 transceiver driver/receiver interface IC semiconductor UART full-duplex communication ESD protection 20-pin TSSOP TSSOP package family surface-mount package +2.35 V to +5.5 V supply 1 µA supply current 15 kV ESD protection industrial control data cable
빠른 견적 RFQ
상세 정보를 모두 입력하십시오 — 영업팀이 24시간 이내에 답변드립니다
부품 번호 제조사 패키지 QTY 목표 가격 합계
✓
견적이 제출되었습니다!

24시간 이내에 이메일로 답변드리겠습니다

1
RFQ 제출됨
2
견적 접수됨
3
주문 완료
4
결제
5
배송됨
6
배송 완료
RFQ 상세 보기