MC9S08GT16CFD - 8-Bit 40MHz 16KB Flash MCU | NXP
부품 번호: MC9S08GT16CFD ✗ 단종| 수량 | 단가 | 합계 |
|---|---|---|
| 1 | $0 | $0.00 |
| 10 | $0 | $0.00 |
| 100 | $0 | $0.00 |
| 500 | $0 | $0.00 |
| 1,000 | $0 | $0.00 |
MC9S08GT16CFD 개요
An S08 microcontroller is an 8-bit embedded microcontroller in the broader hierarchy of embedded processors, microcontrollers, and semiconductors. It executes firmware from flash memory and provides general-purpose I/O, interrupt handling, timers, communications interfaces, and analog or timing resources depending on the device variant. The MC9S08GT16CFD family is intended for designs that need deterministic embedded control rather than a high-level application processor.
The principal verified characteristics are an 8-bit CPU, 40 MHz maximum operating frequency, and 16 KB flash memory. The package is a 48-terminal no-lead square QFN with an exposed pad, identified by package code HVQCCN in distributor data. The S08 instruction set includes the BGND instruction according to the retrieved technical description, and the device supports up to 32 interrupt or reset sources. Software-selectable port pullups and internal pullups on RESET and IRQ are also identified as design features.
The 40 MHz clock rate provides useful processing headroom for control loops, protocol servicing, and supervisory logic, while the 16 KB flash capacity supports compact firmware. The exposed-pad package improves board-level heat spreading when used with a properly designed thermal pad and copper area, but final thermal performance depends on PCB construction, copper area, airflow, and the actual operating condition.
Typical application domains include industrial control modules, motor or actuator supervisory circuits, building and access-control equipment, consumer appliances, instrumentation, and low-cost embedded nodes. Selection should begin with the verified 40 MHz performance, 16 KB flash requirement, S08 software compatibility, and the exact 48-QFN-EP footprint.
Place the decoupling network close to the supply pins and preserve the exposed-pad land pattern and thermal-via layout specified by the manufacturer package documentation. Confirm pin functions, voltage limits, peripheral availability, programming requirements, and lifecycle status against the current NXP datasheet before releasing a production design.
This page consolidates verified distributor specifications, package information, sourcing references, and engineering guidance for engineers comparing the MC9S08GT16CFD with other embedded-control solutions. It does not infer undocumented electrical limits or claim a drop-in replacement unless the manufacturer footprint and pinout have been independently confirmed.
드롭인 대체품: MC9S08GT16CFD — 동일 패키지, 핀 호환. PCB 재작업이 필요한 다른 패키지 부품은 제외됩니다.
이 시리즈의 변형
다음과 드롭인 호환되는 동일 시리즈 모델: MC9S08GT16CFD (동일 폼 팩터 및 풋프린트) — 차이점: Instruction Set.
빠른 비교 도구 — 나란히 비교할 대체 부품을 선택하십시오:
MC9S08GT16CFD-MO
✅ 드롭인📋 참조 대체품 (카탈로그에 없음)
MC9S08GT16ACFCE
✅ 드롭인✓ 재고 있음
$2.31 / 개
데이터시트 보기 →MC9S08GT16CFD 최대 정격 & 전기적 특성
| CPU Architecture | 8-bit HCS08 CPU |
| Maximum CPU Frequency | 40 MHz |
| Flash Memory | 16 KB |
| Flash Organization | 16K x 8 |
| Instruction Set | HC08 instruction set with added BGND instruction |
| Interrupt or Reset Sources | Up to 32 sources |
| General-Purpose I/O | 38 general-purpose I/O pins identified in retrieved technical data |
| Port Pullups | Software selectable on ports when used as inputs |
| RESET Pullup | Internal pullup identified in retrieved technical data |
| IRQ Pullup | Internal pullup identified in retrieved technical data |
| Package Type | 48-QFN-EP |
| Package Dimensions | 7 mm x 7 mm |
| Package Code | HVQCCN |
| Terminal Count | 48 terminals |
| Terminal Form | No lead |
| Temperature Grade | Industrial |
| Device Class | Embedded microcontroller |
MC9S08GT16CFD hvqccn 핀 구성 가이드
MC9S08GT16CFD(hvqccn 패키지)의 핀 구성입니다. 이 디지털 IC에는 GPIO, 통신 인터페이스(UART, SPI, I2C), 전원 핀이 포함되어 있습니다. 대체 핀 기능과 구성 옵션은 제조사 데이터시트를 참조하십시오. 임베디드 시스템 설계와 PCB 레이아웃에 필수적입니다.
다음에 대한 상세 핀아웃 데이터 없음: MC9S08GT16CFD.
다음을 참조하십시오: 데이터시트 전체 핀 구성은 다음을 참조하십시오.
일반적인 애플리케이션
MC9S08GT16CFD 적합 용도: 6 애플리케이션s: Industrial Control Module, Motor and Actuator Supervision, Building and Access-Control Equipment, Consumer Appliance Controller, Instrumentation and Data Acquisition, HMI and Display Peripheral Control.
Industrial Control Module
The MC9S08GT16CFD fits compact industrial-control modules that supervise sensors, actuators, interlocks, and system status. Its verified 40 MHz 8-bit S08 CPU provides deterministic processing capability, while 16 KB of flash supports firmware for state machines, diagnostics, debouncing, and communication service routines. The 48-QFN-EP package helps reduce board area in control assemblies where the exposed pad can be tied to a carefully designed thermal copper area. The designer should confirm voltage limits, RAM, timer resources, and communication peripherals in the current datasheet before assigning exact control functions.
추천
Motor and Actuator Supervision
The MC9S08GT16CFD can supervise motors, solenoids, relays, and other actuators in compact equipment where a dedicated higher-level processor is unnecessary. At up to 40 MHz, the 8-bit S08 core can execute timing sequences, limit checks, fault flags, and safety-state transitions while 16 KB flash stores the application firmware. The QFN-EP footprint is useful in space-constrained boards, but exposed-pad layout and thermal-via construction must follow the package requirements. Exact PWM, capture, ADC, and protection capabilities remain data-needed until confirmed in the manufacturer documentation.
추천
Building and Access-Control Equipment
The MC9S08GT16CFD is suitable for access-control readers, lock controllers, door interfaces, and building-automation subnodes that require local real-time decisions. Its 8-bit architecture and 16 KB flash capacity fit compact firmware for credential handling, keypad or reader scanning, relay control, status indication, and fault reporting. The verified RESET and IRQ pullup features can reduce external support components, while software-selectable port pullups can simplify input conditioning. Designers must still verify absolute maximum ratings, supply voltage, ESD requirements, security boundaries, and package-specific pin assignments in the official documentation.
추천
Consumer Appliance Controller
The MC9S08GT16CFD can serve as the primary embedded controller in a small appliance, display module, or user-interface accessory. Its 40 MHz S08 processor supports responsive menu handling, button scanning, indicator control, sensor polling, and supervisory logic, while the 16 KB flash capacity constrains firmware size and encourages compact modular code. The 48-QFN-EP package supports dense layouts but requires careful land-pattern reproduction and thermal design. Before using it in a consumer product, verify EMC-related design guidance, ESD protection, supply tolerances, endurance requirements, and production programming requirements from the manufacturer sources.
추천
Instrumentation and Data Acquisition
The MC9S08GT16CFD can be evaluated for instrumentation nodes that perform local signal conditioning decisions, calibration handling, status reporting, and data pre-processing. The verified 8-bit architecture is appropriate for deterministic supervisory tasks, and the 40 MHz operating point provides more headroom than basic low-clock control loops. The 16 KB flash footprint may be sufficient for compact firmware, but the supplied data does not identify ADC resolution, RAM, timers, or communication interfaces. Those capabilities must be confirmed before selecting it for precision measurement, and analog front-end design must be validated separately from the digital MCU selection.
추천
HMI and Display Peripheral Control
The MC9S08GT16CFD may fit compact HMI peripherals, display-keypad modules, and status panels where a local microcontroller must scan inputs and update indicators. The 40 MHz S08 core can manage timing and event handling, while 16 KB flash provides storage for compact UI logic and configuration data. The package’s 48-QFN-EP form factor can reduce board area, but the exposed pad must be connected according to the package drawing and thermal strategy. Display voltage, serial interface, ESD protection, and connector pinout requirements should be treated as separate engineering checks because they are not specified in the supplied verification data.
추천
추천 제품 요약
엔지니어링 참조 데이터: MC9S08GT16CFD — 비교, 설계 지침 및 규정 준수 정보.
선택 가이드
대체품과의 비교
| 파라미터 | 이 제품 | MC9S08GT16CFD-MO | MC9S08GT16 |
|---|---|---|---|
| Brand | NXP Semiconductors | NXP Semiconductors | NXP Semiconductors |
| CPU Architecture | 8-bit HCS08 S08 | 8-bit S08, stated in listing | S08 family identification |
주요 차별점
- Verified 40 MHz operation (vs MC9S08GT16CFD-MO)
- Compact exposed-pad package (vs MC9S08GT16)
- Documented input-support features (vs MC9S08GT16CFD-MO)
- Flash-backed 8-bit architecture (vs MC9S08GT16)
설계 노트
Reproduce the manufacturer’s 48-QFN-EP land pattern rather than substituting a generic 48-QFN footprint. The retrieved distributor records identify a 7 mm x 7 mm no-lead package with an exposed pad and HVQCCN package code. Verify pad dimensions, pitch, thermal-via recommendations, solder-mask clearance, and pin-one orientation against the current package drawing before release. Because the supplied data does not include the numbered pinout or land pattern, do not infer these details from the package family name.
Treat the exposed pad as a thermal and electrical construction feature, not as an optional copper pour. Follow the manufacturer’s exposed-pad connection and via recommendations, and provide a continuous or properly segmented thermal copper area appropriate to the board stack-up. Actual junction temperature depends on package dissipation, ambient temperature, copper area, via count, airflow, and the verified operating mode; the supplied data does not provide thermal resistance or maximum power, so those values must be obtained from the datasheet before thermal approval.
Do not treat MC9S08GT16CFD-MO as an exact substitute solely because it appears in a distributor result. Confirm the base MPN, suffix meaning, manufacturer, temperature grade, package marking, flash and RAM configuration, pin multiplexing, clock requirements, and lifecycle status. Also verify that firmware and boot configuration are compatible. The provided data confirms family characteristics but does not establish every electrical or ordering parameter for the suffix.
규정 준수 정보
The supplied distributor snippets identify industrial temperature grade and package information but do not provide RoHS, REACH, AEC-Q100, lead-free, halogen-free, or conflict-minerals declarations. These fields remain unknown rather than inferred.
