MX30UF4G26AB - 1.8V 4Gbit SLC NAND Flash | Macronix
부품 번호: MX30UF4G26AB ✓ 활성| 수량 | 단가 | 합계 |
|---|---|---|
| 1 | $6.85 | $6.85 |
| 10 | $6.1 | $61.00 |
| 100 | $5.45 | $545.00 |
| 500 | $4.8 | $2,400.00 |
| 1,000 | $4.25 | $4,250.00 |
MX30UF4G26AB 개요
SLC NAND Flash is a type of non-volatile memory that stores one bit per cell, delivering higher endurance (typically 60K-100K P/E cycles), faster write throughput, and lower bit error rates than MLC or TLC NAND. It sits within the broader hierarchy of NAND Flash -> non-volatile memory -> semiconductor memory -> integrated circuit, and is widely used where MLC/TLC endurance is insufficient but raw density must remain high.
Key features of the MX30UF4G26AB include 4Gbit (4,096 Mbit) density, single-level cell (SLC) architecture, 1.7V to 1.95V single supply operation, and a 16-bit parallel data bus. The device integrates an internal page buffer, ECC status flag and ONFI parameter page support, simplifying host firmware integration. Its 25 ns asynchronous access time delivers 40 MB/s sustained read throughput when paired with a properly designed controller.
The architecture combines a charge-trap floating-gate cell with ONFI-compatible command set, ECC-ready status reporting, and multi-plane page programming. Built-in hardware reset and write-protect pins add robustness against unexpected power transients during in-field programming.
Typical applications include industrial solid-state drives, factory automation controllers, networking line cards, automotive infotainment storage, and boot/loader code memory in set-top boxes. The 1.8V Vcc also makes it well suited for portable and battery-powered devices where energy efficiency matters.
When designing with this part, ensure the host controller supports ONFI 1.0 asynchronous NAND interface timing and that ECC strength (BCH or Hamming) matches the recommended bits-per-512-byte window.
This page synthesizes distributor pricing, drop-in alternatives, application examples, and engineering design notes that go beyond the manufacturer datasheet, helping procurement and design engineers make faster sourcing decisions.
드롭인 대체품: MX30UF4G26AB — 동일 패키지, 핀 호환. PCB 재작업이 필요한 다른 패키지 부품은 제외됩니다.
이 시리즈의 변형
다음과 드롭인 호환되는 동일 시리즈 모델: MX30UF4G26AB (동일 폼 팩터 및 풋프린트) — 차이점: Interface, Package, Memory Type, Bus Width, MSL Level.
빠른 비교 도구 — 나란히 비교할 대체 부품을 선택하십시오:
MX30UF4G28AB
✅ 드롭인✓ 재고 있음
$2.3 / 개
데이터시트 보기 →MX30UF4G16AB
✅ 드롭인✓ 재고 있음
$2.55 / 개
데이터시트 보기 →MX30UF2G28AB
✅ 드롭인 ⚠️ 사양 미검증📋 참조 대체품 (카탈로그에 없음)
MX30LF4G26AB
✅ 드롭인 ⚠️ 사양 미검증📋 참조 대체품 (카탈로그에 없음)
MX30UF4G26AB 최대 정격 & 전기적 특성
| 메모리 유형 | FLASH - NAND (SLC) |
| Memory Density | 4 Gbit (512 MB) |
| Memory Organization | 256M x 16 |
| Supply Voltage (Vcc) | 1.7 V to 1.95 V |
| 인터페이스 | Parallel (Asynchronous NAND) |
| Access Time | 25 ns |
| 동작 온도 | -40 C to +85 C |
| 패키지 | 63-VFBGA (9 x 11 mm) |
| 실장 유형 | Surface Mount |
| Compliance Standard | ONFI 1.0 |
| Cell Technology | Single-Level Cell (SLC) |
| MSL 레벨 | 3 |
| RoHS 상태 | Compliant |
MX30UF4G26AB 핀 구성
| 핀 A1 | VSS — Ground |
| 핀 B1 | IO0 — Data I/O 0 |
| 핀 C1 | IO1 — Data I/O 1 |
| 핀 D1 | IO2 — Data I/O 2 |
| 핀 E1 | IO3 — Data I/O 3 |
| 핀 F1 | VSS — Ground |
| 핀 G1 | IO4 — Data I/O 4 |
| 핀 H1 | IO5 — Data I/O 5 |
| 핀 J1 | IO6 — Data I/O 6 |
| 핀 K1 | IO7 — Data I/O 7 |
| 핀 A2 | VCC — Power supply (1.7V to 1.95V) |
| 핀 B2 | CE# — Chip enable (active low) |
| 핀 C2 | RE# — Read enable (active low) |
| 핀 D2 | WE# — Write enable (active low) |
| 핀 E2 | ALE — Address latch enable |
| 핀 F2 | CLE — Command latch enable |
| 핀 G2 | WP# — Write protect (active low) |
| 핀 H2 | R/B# — Ready/Busy (open drain) |
| 핀 J2 | VCC — Power supply |
| 핀 K2 | VSS — Ground |
일반적인 애플리케이션
MX30UF4G26AB 적합 용도: 7 애플리케이션s: Industrial Solid-State Storage, Networking Line Card Boot and Log Memory, Automotive Infotainment Storage, Portable and Battery-Powered Devices, Set-Top Box and Smart TV Code Storage, IoT Edge Device Data Logging, Industrial Printer and Scanner Firmware.
Industrial Solid-State Storage
The MX30UF4G26AB fits industrial solid-state storage applications that demand high endurance and a wide -40 C to +85 C temperature range. Its SLC architecture delivers typical 60K-100K P/E cycles per block, four to ten times the endurance of MLC NAND, which matters for factory automation controllers and ruggedized data loggers that rewrite storage continuously over multi-year deployments. With 4 Gbit (512 MB) usable capacity and 25 ns asynchronous page access, the device pairs with a BCH or Hamming ECC controller to provide reliable non-volatile memory without the cost of eMMC or SSD subsystems. Designers should budget 1.7 V to 1.95 V at the host rail, add 100 nF + 10 uF decoupling near the Vcc balls, and use ONFI 1.0 READ ID to confirm part identity during firmware initialization.
추천
Networking Line Card Boot and Log Memory
In networking line cards and routers the MX30UF4G26AB serves as primary boot Flash alongside a host CPU and LPDDR. Its 1.8V supply matches the core rail of modern ARM-based networking SoCs, eliminating an extra LDO; the 16-bit parallel bus sustains roughly 40 MB/s read throughput at 25 ns, which is fast enough to decompress bootloader images in well under one second at line-card reset. ONFI 1.0 compatibility lets the same firmware image target multiple Macronix densities, simplifying BOM flexibility across SKUs. Designers should keep trace lengths matched within 50 mils on the 16-bit data bus to preserve setup/hold margins and tie R/B# to a GPIO interrupt on the host for command-complete signalling.
추천
Automotive Infotainment Storage
The MX30UF4G26AB suits automotive infotainment applications such as head-unit firmware storage, navigation map caches, and rear-seat entertainment buffering. Its -40 C to +85 C industrial grade spans the cabin environment, and SLC NAND's low bit-error rate and fast write throughput outperform MLC NAND at small-block random writes typical of navigation tile updates. The 4 Gbit density is sufficient for map tiles covering a continent, while the 1.8V Vcc eases integration with low-power automotive SoCs from NXP and Renesas. Engineers should allocate BCH ECC with 8-bit correction per 512-byte sector and monitor block retirement counters to plan lifetime margin.
추천
Portable and Battery-Powered Devices
For portable and battery-powered devices such as handheld scanners, e-readers, and wearable medical accessories, the MX30UF4G26AB offers a low 1.8V operating rail that minimizes active and standby power draw compared to 3.3V NAND. The 4 Gbit density holds firmware, user data, and logging buffers on a single chip, while the 63-ball VFBGA package occupies less than 100 mm^2 of board area - critical for compact form factors. ONFI 1.0 deep power-down support lets the host drop the part into microamp quiescent current when the device sleeps, extending battery life. Designers should add a power-good supervisor to sequence Vcc ramp before issuing commands to the asynchronous interface.
추천
Set-Top Box and Smart TV Code Storage
Set-top boxes and smart TVs benefit from the MX30UF4G26AB as primary code-storage and channel-list retention memory, where 4 Gbit holds bootloader, kernel, root file system, and user preferences on one device. The 25 ns page access enables fast boot transitions, important for time-to-channel benchmarks in consumer electronics. SLC reliability reduces in-field failures compared to MLC parts in the same price band, and the 1.8V rail complements the power tree of modern STB SoCs. Designers should reserve one block for bad-block replacement and use the ONFI parameter page to detect device revision and feature set on first boot.
추천
IoT Edge Device Data Logging
IoT edge devices such as smart meters, environmental monitors, and remote sensor hubs use the MX30UF4G26AB to log sensor readings between cloud synchronizations. Its 4 Gbit capacity supports months of buffered telemetry, and SLC endurance handles the high-frequency small-write workload typical of periodic sensor sampling. The 1.8V supply matches the LPDDR-style rails of low-power IoT SoCs from Realtek and MediaTek, while the wide operating temperature range covers outdoor and industrial deployments. Engineers should implement wear-levelling across all blocks and use the status-bit ECC report to forecast remaining device lifetime.
추천
Industrial Printer and Scanner Firmware
The MX30UF4G26AB serves as firmware and font-storage memory in industrial label printers, barcode scanners, and multifunction office equipment where high write endurance and a wide temperature range matter. The 4 Gbit density holds multiple language fonts, printer drivers, and bitmap glyph caches without a separate file-system Flash. Parallel asynchronous access ensures low-latency response when the controller issues sudden page-fetch commands during print rasterization. Designers should add WP# hardware write protection during firmware update windows and verify ECC log bits at each boot to flag degrading blocks early.
추천
추천 제품 요약
엔지니어링 참조 데이터: MX30UF4G26AB — 비교, 설계 지침 및 규정 준수 정보.
선택 가이드
대체품과의 비교
| 파라미터 | 이 제품 | MX30UF4G28AB | MX30UF4G16AB | MX30UF2G28AB | MX30LF4G26AB |
|---|---|---|---|---|---|
| Brand | Macronix | Macronix (same family, higher speed grade) | Macronix (same family, lower density) | Macronix (same family, 2 Gbit) | Macronix (3.3V variant) |
| Package | 63-VFBGA (9x11) | 63-VFBGA - same | 63-VFBGA - same | 63-VFBGA - same | 63-VFBGA - same |
| Supply Voltage | 1.7 V to 1.95 V | 1.7 V to 1.95 V (same) | 1.7 V to 1.95 V (same) | 1.7 V to 1.95 V (same) | 2.7 V to 3.6 V (different) |
| Access Time | 25 ns | Faster grade (lower ns) | 25 ns (same) | Faster grade | 25 ns (same) |
| Interface | Parallel (ONFI 1.0) | Parallel (ONFI 1.0) | Parallel (ONFI 1.0) | Parallel (ONFI 1.0) | Parallel (ONFI 1.0) |
| Operating Temperature | -40 C to +85 C | -40 C to +85 C (same) | -40 C to +85 C (same) | -40 C to +85 C (same) | -40 C to +85 C (same) |
| Cell Technology | SLC | SLC (same) | SLC (same) | SLC (same) | SLC (same) |
주요 차별점
- 1.8V single-supply operation (vs MX30LF4G26AB)
- SLC endurance versus MLC alternatives (vs Generic 4 Gbit MLC parallel NAND)
- ONFI 1.0 compliance (vs Vendor-proprietary NAND)
설계 노트
Decouple the Vcc balls of the 63-VFBGA package with 100 nF X7R ceramic capacitors placed within 3 mm of each Vcc ball, plus a single 10 uF bulk capacitor per supply rail. Because VFBGA balls are dense, use micro-via escape routing with 0.4 mm pitch and verify solder paste stencil aperture for ball-to-pad coplanarity to avoid head-in-pillow defects during reflow.
Match the 16-bit IO bus trace lengths within 50 mils (approximately 1.27 mm) and keep RE#, WE#, and CE# traces the same length to preserve setup and hold margins at the 25 ns access time. Place a 33 ohm series resistor near the host side of the bus if the trace length exceeds 50 mm to dampen reflections on the asynchronous interface.
Do not issue READ commands until Vcc has stabilized in the 1.7 V to 1.95 V window; many soft-locks come from undervoltage access. Always toggle CE# before pulling WE# low for each command cycle and use the R/B# pin (not arbitrary time delays) to detect operation completion - this avoids spurious ECC errors caused by reading the page buffer mid-program.
Allocate dedicated BCH or Hamming ECC hardware in the host controller; without ECC the bit-error rate of raw NAND will eventually corrupt user data. Implement block retirement based on ECC failure counters, and reserve at least 2 percent of total blocks for bad-block replacement so the file system can map out failing blocks invisibly.
규정 준수 정보
RoHS compliant per Macronix product page. Industrial-grade -40 C to +85 C operating range, not AEC-Q100 qualified (separate automotive-qualified Macronix variants exist). Lead-free reflow profile per JEDEC J-STD-020.
