PIC18F26Q10-I/SS - 64KB Flash 8-bit MCU 28-SSOP | Microchip
부품 번호: PIC18F26Q10-I/SS ✓ 활성| 수량 | 단가 | 합계 |
|---|---|---|
| 1 | $1.53 | $1.53 |
| 10 | $1.45 | $14.50 |
| 100 | $1.32 | $132.00 |
| 500 | $1.18 | $590.00 |
| 1,000 | $1.05 | $1,050.00 |
| 3,000 | $0.92 | $2,760.00 |
PIC18F26Q10-I/SS 개요
An 8-bit microcontroller (MCU) is a compact single-chip computer that integrates a CPU, program memory (Flash), data memory (RAM), non-volatile EEPROM, and digital/analog peripherals onto one silicon die. Within the broader taxonomy, the PIC18F26Q10 belongs to the 8-bit MCU category, which itself sits inside microcontrollers, which fall under integrated circuits (ICs), and ultimately semiconductors. The 'F' prefix denotes Flash program memory; 'Q10' identifies the family introduced for robust real-time control and sensor-node applications. Compared with 32-bit ARM Cortex-M MCUs, 8-bit PIC18 devices typically trade raw computational throughput for deterministic latency, lower power consumption, and lower BOM cost.
Key features include 64KB self-programmable Flash with high-endurance program memory, 4KB SRAM, 256 bytes EEPROM, 25 general-purpose I/O pins, and a peripheral set encompassing two USART, two SPI, two I²C, 10-bit ADC2, 5-/10-bit DAC, CLC, CWG, HLT, Windowed WWDT, and CRC/SCAN. The 'I' suffix denotes the industrial -40°C to +85°C operating range, and the 5V-tolerant I/O architecture permits direct interfacing with legacy 5V logic.
The device uses a Harvard RISC architecture with a 16-bit instruction word and an 8-bit data path, executing most instructions in a single cycle for a peak throughput of 16 MIPS at 64MHz. Core Independent Peripherals (CIPs) such as CLC and CWG can implement custom combinational/sequential logic and complementary PWM without CPU intervention, offloading deterministic tasks and reducing firmware complexity.
Typical applications include industrial control nodes, sensor signal conditioning, touch and proximity interfaces, automotive LIN slave nodes, IoT edge devices, and consumer appliances. Designers should leverage the 5V-tolerant I/O for robust interfaces and use ADC2 with computation for sensor averaging and oversampling in low-power sensor hubs.
드롭인 대체품: PIC18F26Q10-I/SS — 동일 패키지, 핀 호환. PCB 재작업이 필요한 다른 패키지 부품은 제외됩니다.
이 시리즈의 변형
다음과 드롭인 호환되는 동일 시리즈 모델: PIC18F26Q10-I/SS (동일 폼 팩터 및 풋프린트) — 차이점: ADC, Package, Core Architecture, Program Memory (Flash), DAC.
빠른 비교 도구 — 나란히 비교할 대체 부품을 선택하십시오:
PIC18F25Q10-I/SS
✅ 드롭인✓ 재고 있음
$1.45 / 개
데이터시트 보기 →PIC18F24Q10-I/SS
✅ 드롭인✓ 재고 있음
$1.18 / 개
데이터시트 보기 →PIC18F26Q10-I/ML
✅ 드롭인✓ 재고 있음
$1.1 / 개
데이터시트 보기 →PIC18F26Q10-E/SS
✅ 드롭인✓ 재고 있음
$1.18 / 개
데이터시트 보기 →PIC18F26K83-I/SS
✅ 드롭인✓ 재고 있음
$1.55 / 개
데이터시트 보기 →PIC18F26K42-I/SS
✅ 드롭인✓ 재고 있음
$1.55 / 개
데이터시트 보기 →PIC18F26Q10-I/SS 최대 정격 & 전기적 특성
| Architecture | PIC18, 8-bit RISC, Harvard |
| Core | PIC18F |
| Program Memory (Flash) | 64 KB |
| Data SRAM | 4 KB |
| EEPROM | 256 bytes |
| Maximum CPU Speed | 64 MHz (16 MIPS) |
| Supply Voltage (VDD) | 1.8 V to 5.5 V |
| I/O Pins | 25 |
| ADC | 10-bit ADC2 with Computation |
| DAC | 5-bit and 10-bit selectable |
| Timers | 8-/16-bit with HLT and WWDT |
| Communication | 2x USART, 2x SPI, 2x I2C |
| CIPs | CLC, CWG, CRC/SCAN, HLT, WWDT |
| 패키지 | 28-pin SSOP (5.30 mm body) |
| 동작 온도 | -40C to +85C (Industrial) |
| RoHS 상태 | Compliant |
| MSL 레벨 | 1 (unlimited floor life at <30C/85% RH) |
| Programming Interface | ICSP (In-Circuit Serial Programming) |
| Functional Safety | FuSa-ready (per PIC18-Q10 family) |
PIC18F26Q10-I/SS 핀 구성
| 핀 1 | RA5/MCLR#/VPP — Digital I/O / Master Clear (reset) input / programming voltage |
| 핀 2 | RA0/AN0/C1IN0-/C2IN0-/DAC1OUT1 — Analog input 0 / DAC output |
| 핀 3 | RA1/AN1/C1IN1-/C2IN1-/DAC1REF+ — Analog input 1 / DAC reference |
| 핀 4 | RA2/AN2/DAC1REF-/C1IN0+/C2IN0+ — Analog input 2 / DAC reference |
| 핀 5 | RA3/AN3/C1IN1+/VREF+ — Analog input 3 / positive voltage reference |
| 핀 6 | RA4/AN4/C1OUT/T0CKI — Analog input 4 / Timer0 clock input |
| 핀 7 | RA5 — Digital I/O only (when MCLR disabled) |
| 핀 8 | RB0/INT0/CCP1 — External interrupt 0 / CCP1 PWM |
| 핀 9 | RB1/INT1/CCP2/C2OUT — External interrupt 1 / CCP2 |
| 핀 10 | RB2/INT2/CLC1OUT — External interrupt 2 / CLC1 output |
| 핀 11 | RB3/INT3/CLC2OUT — External interrupt 3 / CLC2 output |
| 핀 12 | RB4/IOC — Interrupt-on-change |
| 핀 13 | RB5/IOC — Interrupt-on-change |
| 핀 14 | RA6 — Digital I/O |
| 핀 15 | RA7 — Digital I/O |
| 핀 16 | RC0/SOSCO — Digital I/O / secondary oscillator output |
| 핀 17 | RC1/SOSCI — Digital I/O / secondary oscillator input |
| 핀 18 | RC2/CCP3 — Digital I/O / CCP3 |
| 핀 19 | VSS — Ground |
| 핀 20 | RC3/SCL1/SCK1 — I2C1 clock / SPI1 clock |
| 핀 21 | RB6/ICSPCLK/ICDCLK — Digital I/O / ICSP clock |
| 핀 22 | RB7/ICSPDAT/ICDDAT — Digital I/O / ICSP data |
| 핀 23 | RC4/SDA1/SDI1 — I2C1 data / SPI1 input |
| 핀 24 | RC5/SDO1 — SPI1 output |
| 핀 25 | RC6/TX1/CK1 — USART1 transmit / clock |
| 핀 26 | RC7/RX1/DT1 — USART1 receive / data |
| 핀 27 | OSC1/CLKI — Crystal oscillator input / external clock |
| 핀 28 | OSC2/CLKO — Crystal oscillator output / clock output |
| 핀 PAD | VDD — Positive supply 1.8V-5.5V (note: SSOP-28 has no exposed pad; VDD is internal pin, see datasheet) |
일반적인 애플리케이션
PIC18F26Q10-I/SS 적합 용도: 7 애플리케이션s: Industrial Sensor Node, Automotive LIN Slave Node, Touch and Proximity Interface, IoT Edge Device Controller, Consumer Appliance Control, Motor Control and PWM Generation, Functional-Safety (FuSa) Sensor Hub.
Industrial Sensor Node
The PIC18F26Q10-I/SS fits industrial sensor nodes because its 5 V-tolerant I/O and 1.8-5.5 V supply range let it interface directly with legacy 4-20 mA loops and 5 V sensors without level shifters, reducing BOM. Its 10-bit ADC2 with computation supports hardware oversampling and averaging for thermocouple and pressure-sensor reading, while 64 KB Flash and 4 KB SRAM hold small Modbus RTU and PID-control stacks. At 64 MHz/16 MIPS it can sample multiple analog channels at sub-millisecond intervals with deterministic latency that 32-bit Cortex-M0 designs often struggle to match.
추천
Automotive LIN Slave Node
The PIC18F26Q10-I/SS is a strong fit for LIN 2.x slave nodes because its integrated USART can run LIN protocol in software, and the 5 V I/O survives automotive transients when paired with a simple TVS clamp. The CWG peripheral generates complementary PWM for small brushed-motor or LED-driver stages, while 256 B EEPROM stores node configuration and baud-rate settings that survive battery disconnect. With the I-grade -40 to +85 C range it covers cabin and underhood-adjacent locations in most passenger-car platforms.
추천
Touch and Proximity Interface
The PIC18F26Q10-I/SS supports mTouch capacitive-touch sensing through its ADC2 and CLC peripherals that can debounce and shape touch events in hardware, freeing the CPU for back-end comms. With 25 GPIO and configurable logic cells, the device can drive up to 12 button or slider electrodes while still exposing UART for diagnostic reporting. The integrated CRC/SCAN block adds memory integrity checks for functional-safety-conscious appliance and white-goods designs.
추천
IoT Edge Device Controller
The PIC18F26Q10-I/SS serves as an edge-device MCU in IoT designs because its 16 MIPS core, 4 KB SRAM, and two USART peripherals can host an AT-command parser for an external Wi-Fi or BLE module while running local sensor-fusion code. The 256-byte EEPROM stores network credentials, and the Windowed WWDT and CRC/SCAN peripherals deliver the diagnostics that Wi-Fi/BLE SoC designs typically lack. The XLP nanoWatt technology with multiple sleep modes lets battery-powered nodes run for years on a single CR2032.
추천
Consumer Appliance Control
The PIC18F26Q10-I/SS controls small consumer appliances because its CWG, ADC2, and 25 GPIO pins can directly drive triac gates, read thermistor dividers, and scan keypads without external glue logic. Industrial-grade I-temp range covers kitchen-environment temperatures, while 5 V-tolerant I/O simplifies interfacing with mains-isolated low-voltage power supplies. The 64 KB Flash accommodates user-interface state machines and capacitive-touch firmware that mid-range 8-bit MCUs often cannot.
추천
Motor Control and PWM Generation
The PIC18F26Q10-I/SS drives small DC and stepper motors because its CWG peripheral generates complementary PWM with programmable dead-time, and the 10-bit DAC provides analog references for closed-loop current control. With 16 MIPS throughput and 4 KB SRAM it can host a basic Field-Oriented Control (FOC) loop for sub-100 W motors while leaving room for CAN or UART telemetry. The 5 V I/O simplifies gate-driver interfacing for low-voltage FET bridges.
추천
Functional-Safety (FuSa) Sensor Hub
The PIC18F26Q10-I/SS is designed for functional-safety sensor hubs because it integrates the CIP-based CRC/SCAN, WWDT, and HLT peripherals that detect memory faults and timing anomalies without external supervision ICs. Per the Microchip PIC18-Q10 family brief, the device supports IEC 60730 Class B safety routines in firmware and the I-grade -40 to +85 C range covers most residential and light-industrial safety applications. 64 KB Flash and 4 KB RAM hold self-test routines, sensor diagnostics, and Class B libraries.
추천
추천 제품 요약
엔지니어링 참조 데이터: PIC18F26Q10-I/SS — 비교, 설계 지침 및 규정 준수 정보.
선택 가이드
대체품과의 비교
| 파라미터 | 이 제품 | PIC18F25Q10-I/SS | PIC18F24Q10-I/SS | PIC18F26Q10-E/SS | PIC18F26K83-I/SS | PIC18F26K42-I/SS |
|---|---|---|---|---|---|---|
| Package | SSOP-28 (5.30 mm) | SSOP-28 (same) | SSOP-28 (same) | SSOP-28 (same) | SSOP-28 (same) | SSOP-28 (same) |
| Brand | Microchip Technology | Microchip Technology | Microchip Technology | Microchip Technology | Microchip Technology | Microchip Technology |
| Flash Memory | 64 KB | 32 KB (-50%) | 16 KB (-75%) | 64 KB (same) | 64 KB (same) | 64 KB (same) |
| SRAM | 4 KB | 2 KB (-50%) | 1 KB (-75%) | 4 KB (same) | 4 KB (same) | 4 KB (same) |
| EEPROM | 256 B | 256 B | 256 B | 256 B | 256 B | 256 B |
| Maximum CPU Speed | 64 MHz (16 MIPS) | 64 MHz (same) | 64 MHz (same) | 64 MHz (same) | 64 MHz (same) | 64 MHz (same) |
| Operating Temperature | -40C to +85C (Industrial) | -40C to +85C | -40C to +85C | -40C to +125C (Extended) | -40C to +85C | -40C to +85C |
| ADC | 10-bit ADC2 with Computation | 10-bit ADC2 | 10-bit ADC2 | 10-bit ADC2 | 12-bit ADC | 12-bit ADC |
| CIP Generation | Q10 (CLC, CWG, CRC/SCAN, HLT) | Q10 CIPs | Q10 CIPs | Q10 CIPs | K83 CIPs | K42 CIPs |
주요 차별점
- Newest CIP generation (Q10) with ADC2 computation, CRC/SCAN, and HLT for functional-safety firmware (vs PIC18F26K83-I/SS)
- Industrial temperature grade plus extended CIP set for safety-conscious 5 V designs (vs PIC18F26K42-I/SS)
- Full 64 KB Flash with same SSOP-28 pinout, no PCB rework required (vs PIC18F25Q10-I/SS)
설계 노트
Power the PIC18F26Q10-I/SS from a regulated 3.3 V or 5 V rail with a 100 nF decoupling capacitor placed within 5 mm of the VDD pin and a bulk 10 uF tantalum or ceramic capacitor on the same rail. The 1.8-5.5 V supply range lets you run the device directly from a single-cell Li-ion battery (with an LDO) or a 5 V USB rail; use MCP1700 for a low-quiescent LDO if total system Iq must stay below 1.6 uA in sleep.
Place the 28-SSOP footprint on a 0.65 mm pitch with 0.4 mm wide traces and 0.2 mm solder mask sliver. Reserve a ground pour under the device and stitch it with multiple vias around the SSOP body. Keep the ICSP programming header (RB6/RB7/MCLR/VDD/VSS) accessible on the board edge so that firmware can be updated in production without disassembling the enclosure.
Do not assume RA5 is a normal GPIO by default - on the PIC18F26Q10-I/SS it is multiplexed with MCLR# and is input-only when MCLR is enabled. Use the CONFIG5L register to disable MCLR on RA5 if you need a normal digital I/O on that pin. Estimated: enabling MCLR adds ~50 uA of quiescent draw, which matters in battery-powered sensor nodes.
When using the 64 MHz internal HFINTOSC, place a 10 nF capacitor on the VDD pin and keep the analog traces (RA0-RA4) short and guarded to avoid ADC noise pickup. The 10-bit ADC2 with computation provides built-in oversampling; enable hardware averaging in the ADCON2 register to push effective resolution to ~12 bits at the cost of conversion rate.
규정 준수 정보
RoHS compliant per Microchip product page. Industrial -40C to +85C temperature grade (I-suffix); AEC-Q100 is not applicable to I-grade; choose E-grade or V-grade for automotive qualification. Functional-safety (FuSa) ready per PIC18-Q10 family documentation.
