PIC18LF2610-I/SO - 8-bit 64KB Flash MCU, 40MHz, 28-SOIC | Microchip
부품 번호: PIC18LF2610-I/SO ✓ 활성| 수량 | 단가 | 합계 |
|---|---|---|
| 1 | $7.4 | $7.40 |
| 10 | $6.66 | $66.60 |
| 100 | $5.92 | $592.00 |
| 500 | $5.31 | $2,655.00 |
| 1,000 | $4.78 | $4,780.00 |
PIC18LF2610-I/SO 개요
An 8-bit microcontroller (microcontroller) is a single-chip computer containing a CPU core, Flash program memory, RAM, non-volatile EEPROM, and a rich set of peripherals (timers, ADC, communication interfaces) integrated on one die. PIC18 is Microchip's high-performance 8-bit family, positioned above the PIC16 family by offering a 16-bit instruction word, hardware multiplier, linear memory map, and C-friendly architecture, while still maintaining the 8-bit ALU. Microcontrollers belong to the broader category of embedded controllers and are the workhorse of low-cost, low-power digital systems in industrial, automotive, and consumer products.
The PIC18LF2610 is the low-voltage ('LF') variant of the PIC18F2610, allowing operation down to 2.0 V (versus 4.2 V for the 'F' version), which makes it suitable for battery-powered designs and 3.3 V systems. It carries the PIC18F2X1X/4X1X peripheral set, including nanoWatt power management with multiple idle/sleep modes and an on-chip low-voltage detect (LVD) module. The 'SO' suffix indicates a 28-pin SOIC (300-mil body) industrial temperature range (-40 to +85C) package.
Typical applications include industrial control, motor control (BLDC/stepper via CCP/PWM), sensor signal conditioning (via the 10-bit ADC), USB-to-UART bridges (paired with an external UART/USB bridge IC), lighting controllers, security and alarm panels, and general-purpose 8-bit embedded control boards. The combination of ample Flash (64 KB), generous RAM, and a rich peripheral mix makes it a strong fit for firmware-rich mid-volume designs.
When designing with this part, ensure the in-circuit serial programming (ICSP) pins (RB6/RB7) are brought to a programming header and that VDD decoupling uses 100 nF + bulk capacitance close to the package. Choose the 'LF' variant explicitly when the supply rail is below 4.2 V; otherwise the standard PIC18F2610-I/SO provides the same peripheral set.
This page synthesizes real-time distributor pricing, cross-vendor drop-in alternatives from the Microchip PIC18F2X1X/4X1X family, and practical PCB/firmware design notes not consolidated in the datasheet alone.
드롭인 대체품: PIC18LF2610-I/SO — 동일 패키지, 핀 호환. PCB 재작업이 필요한 다른 패키지 부품은 제외됩니다.
이 시리즈의 변형
다음과 드롭인 호환되는 동일 시리즈 모델: PIC18LF2610-I/SO (동일 폼 팩터 및 풋프린트) — 차이점: Package, ADC, Operating Temperature, Core Architecture, Program Memory (Flash).
빠른 비교 도구 — 나란히 비교할 대체 부품을 선택하십시오:
PIC18LF2610T-I/SO
✅ 드롭인✓ 재고 있음
$5.2 / 개
데이터시트 보기 →PIC18F2610-I/SO
✅ 드롭인✓ 재고 있음
$3.95 / 개
데이터시트 보기 →PIC18LF2620-I/SO
✅ 드롭인📋 참조 대체품 (카탈로그에 없음)
PIC18F25K22-I/SO
✅ 드롭인✓ 재고 있음
$1.78 / 개
데이터시트 보기 →PIC18LF25K22-I/SO
✅ 드롭인✓ 재고 있음
$2.18 / 개
데이터시트 보기 →PIC18LF25K50-I/SO
✅ 드롭인✓ 재고 있음
$2.15 / 개
데이터시트 보기 →PIC18LF2610-I/SO 최대 정격 & 전기적 특성
| Product Family | PIC18F2X1X/4X1X |
| Core | PIC18 8-bit RISC |
| Program Memory (Flash) | 64 KB |
| RAM | 3968 bytes |
| 최대 클록 주파수 | 40 MHz |
| Supply Voltage (LF) | 2.0 V to 5.5 V |
| I/O Pins | 25 |
| A/D Converter | 10-bit, up to 11 channels |
| Comparators | 2 |
| CCP / ECCP Modules | 2 (1 CCP + 1 ECCP) |
| USART | 1 (Enhanced) |
| MSSP (SPI / I2C) | 1 |
| 패키지 | 28-SOIC (SO, 0.295 in / 7.50 mm body) |
| 동작 온도 | -40C to +85C (Industrial) |
| 실장 유형 | Surface Mount |
| RoHS 상태 | Compliant |
| Lead-Free | Yes |
PIC18LF2610-I/SO 핀 구성
| 핀 1 | MCLR/RE3 — Master Clear (reset) input / digital I/O RE3 |
| 핀 2 | RA0/AN0 — PORTA bit 0 / analog input 0 |
| 핀 3 | RA1/AN1 — PORTA bit 1 / analog input 1 |
| 핀 4 | RA2/AN2/VREF- — PORTA bit 2 / analog input 2 / A/D VREF- |
| 핀 5 | RA3/AN3/VREF+ — PORTA bit 3 / analog input 3 / A/D VREF+ |
| 핀 6 | RA4/T0CKI — PORTA bit 4 / Timer0 clock input |
| 핀 7 | RA5/AN4/SS — PORTA bit 5 / analog input 4 / SPI slave select |
| 핀 8 | OSC1/CLKI/RA7 — Oscillator crystal input / external clock input / PORTA bit 7 |
| 핀 9 | OSC2/CLKO/RA6 — Oscillator crystal output / clock output / PORTA bit 6 |
| 핀 10 | RC0/T1OSO/T13CKI — PORTC bit 0 / Timer1 oscillator output / Timer1/3 clock |
| 핀 11 | RC1/T1OSI/CCP2 — PORTC bit 1 / Timer1 oscillator input / CCP2 |
| 핀 12 | RC2/CCP1 — PORTC bit 2 / CCP1 PWM output |
| 핀 13 | RC3/SCK/SCL — PORTC bit 3 / SPI clock / I2C clock |
| 핀 14 | RC4/SDI/SDA — PORTC bit 4 / SPI data in / I2C data |
| 핀 15 | RC5/SDO — PORTC bit 5 / SPI data out |
| 핀 16 | RC6/TX/CK — PORTC bit 6 / USART TX / USART clock |
| 핀 17 | RC7/RX/DT — PORTC bit 7 / USART RX / USART data |
| 핀 18 | VSS — Ground reference |
| 핀 19 | VDD — Positive supply voltage (2.0-5.5 V) |
| 핀 20 | RB0/AN12/INT0 — PORTB bit 0 / analog input 12 / external interrupt 0 |
| 핀 21 | RB1/AN10/INT1 — PORTB bit 1 / analog input 10 / external interrupt 1 |
| 핀 22 | RB2/AN8/INT2 — PORTB bit 2 / analog input 8 / external interrupt 2 |
| 핀 23 | RB3/AN9/CCP2 — PORTB bit 3 / analog input 9 / CCP2 |
| 핀 24 | RB4/AN11/KBI0 — PORTB bit 4 / analog input 11 / KBI interrupt 0 |
| 핀 25 | RB5/KBI1/PGM — PORTB bit 5 / KBI interrupt 1 / LVP programming |
| 핀 26 | RB6/KBI2/PGC — PORTB bit 6 / KBI interrupt 2 / ICSP clock |
| 핀 27 | RB7/KBI3/PGD — PORTB bit 7 / KBI interrupt 3 / ICSP data |
| 핀 28 | AVSS — Analog ground reference |
일반적인 애플리케이션
PIC18LF2610-I/SO 적합 용도: 6 애플리케이션s: Industrial Motor Control (BLDC / Stepper), Sensor Signal Conditioning Front End, Lighting Controller (DALI / DMX / PWM Driver), Security and Alarm Panel, General-Purpose 8-bit Embedded Control Board, Battery-Operated Handheld Meter.
Industrial Motor Control (BLDC / Stepper)
The PIC18LF2610-I/SO is well suited to industrial motor control because its ECCP module delivers hardware PWM up to 10-bit resolution at 40 MHz (10 MIPS), and its 10-bit A/D with up to 11 channels can sample back-EMF or current-shunt feedback for closed-loop commutation. With 64 KB Flash and 3968-byte RAM, it has room for sensorless BLDC or stepper acceleration profiles plus UART diagnostics. The wide 2.0-5.5 V supply lets it run directly from a 24 V->3.3 V step-down in industrial cabinets. The 28-SOIC footprint provides a small board area for inline motor drivers where the MCU sits next to the FET gate-driver.
추천
Sensor Signal Conditioning Front End
The PIC18LF2610-I/SO fits sensor-conditioning front ends for thermocouple, RTD, bridge and strain-gauge applications because its 10-bit A/D with 11 input channels can multiplex several sensors through one MCU, and the two on-chip analog comparators enable window comparators for alarm thresholds. The 3968-byte RAM supports circular DSP buffers for moving-average filtering, while the MSSP (SPI/I2C) can drive an external DAC or EEPROM for calibration data. Operating down to 2.0 V, the part is ideal for 2xAA-powered handheld meters where the standard F variant would not start. Engineers can drop the firmware into PIC18F2610-I/SO when supply exceeds 4.2 V.
추천
Lighting Controller (DALI / DMX / PWM Driver)
The PIC18LF2610-I/SO is a strong fit for digital lighting controllers (DALI, DMX-512, 0-10 V dimming) because its ECCP module provides PWM at frequencies and resolutions ideal for dim-to-warm or RGBW LED channels, and the USART implements DMX-512 or DALI hardware protocol layers. The 64 KB Flash is more than adequate for color-mixing firmware, ramp tables, and remote commands. The 28-SOIC footprint lets the MCU sit inline with the LED driver PCB. The LF supply range allows direct operation from a 3.3 V rail coming off a buck converter downstream of the AC-DC stage.
추천
Security and Alarm Panel
The PIC18LF2610-I/SO is widely used in security/alarm panels because its 25 I/O pins can scan a 4x4 keypad matrix, drive a 16-character LCD via the MSSP/SPI, and monitor multiple zones (PIR, door contact, glass-break) through the 10-bit A/D and comparators. The 64 KB Flash is sufficient for event logging, while 3968-byte RAM handles real-time zone state. The 2.0-5.5 V LF range allows backup-battery (3.6 V LiSOCl2) operation during AC loss, with nanoWatt sleep dropping consumption below 100 uA for multi-year battery life.
추천
General-Purpose 8-bit Embedded Control Board
The PIC18LF2610-I/SO is a flexible general-purpose 8-bit control board MCU, suitable for educational kits, hobby platforms, and mid-volume OEM controllers. Its peripheral mix (1 USART, 1 MSSP SPI/I2C, 2 CCP/ECCP, 2 comparators, 11-channel 10-bit A/D) covers most UART-to-I2C bridges, sensor hubs, and small PLCs. With 64 KB Flash it can run a USB-to-UART converter firmware stack. The 28-SOIC package is widely accepted on through-hole adapter PCBs and is the de-facto 8-bit training and prototyping footprint.
추천
Battery-Operated Handheld Meter
The PIC18LF2610-I/SO is well matched to battery-operated handheld meters (digital multimeters, environmental loggers, portable gas detectors) because the 'LF' 2.0 V minimum supply keeps the part running down to a nearly-drained 2xAA alkaline or single LiSOCl2 primary cell, while the nanoWatt sleep modes drop current to microamps. Its 10-bit A/D handles battery voltage and sensor readings; the ECCP can drive an LCD charge pump or piezoelectric buzzer. The 28-SOIC compact 7.5 mm body saves board area in pocket-sized form factors.
추천
추천 제품 요약
엔지니어링 참조 데이터: PIC18LF2610-I/SO — 비교, 설계 지침 및 규정 준수 정보.
선택 가이드
대체품과의 비교
| 파라미터 | 이 제품 | PIC18LF2610T-I/SO | PIC18F2610-I/SO | PIC18LF2620-I/SO | PIC18F25K22-I/SO | PIC18LF25K22-I/SO | PIC18LF25K50-I/SO |
|---|---|---|---|---|---|---|---|
| Package | 28-SOIC (SO) | 28-SOIC (SO) - same | 28-SOIC (SO) - same | 28-SOIC (SO) - same | 28-SOIC (SO) - same | 28-SOIC (SO) - same | 28-SOIC (SO) - same |
| Brand | Microchip Technology | Microchip Technology | Microchip Technology | Microchip Technology | Microchip Technology | Microchip Technology | Microchip Technology |
| Program Memory (Flash) | 64 KB | 64 KB | 64 KB | 64 KB | 32 KB | 32 KB | 32 KB |
| Supply Voltage (min) | 2.0 V (LF) | 2.0 V | 4.2 V | 2.0 V | 1.8 V | 1.8 V | 1.8 V |
| Maximum Clock Frequency | 40 MHz | 40 MHz | 40 MHz | 40 MHz | 64 MHz | 64 MHz | 48 MHz |
| A/D Converter | 10-bit, 11 ch | 10-bit, 11 ch | 10-bit, 11 ch | 10-bit, 11 ch | 12-bit, 19 ch | 12-bit, 19 ch | 10-bit, 14 ch |
| CAN Module | No | No | No | Yes | No | No | No |
| XLP nanoWatt | nanoWatt | nanoWatt | nanoWatt | nanoWatt | nanoWatt | nanoWatt | XLP (sub-uA) |
주요 차별점
- Wide 2.0-5.5 V supply range (LF variant) (vs PIC18F2610-I/SO)
- Generous 64 KB Flash in a 28-pin package (vs PIC18F25K22-I/SO)
- Industrial temperature range -40C to +85C (vs PIC18LF2610-E/SO)
- Drop-in pin compatibility with PIC18F2610 above 4.2 V (vs PIC18LF25K50-I/SO)
설계 노트
Place a 100 nF decoupling capacitor as close as possible to each VDD/AVSS pair (pins 19/28 on 28-SOIC). Add a bulk 10 uF tantalum or aluminum-polymer on the 3.3 V rail feeding the MCU to handle ECCP PWM inrush. The LF variant tolerates supply down to 2.0 V, but if you run close to brown-out, set the BOR (brown-out reset) voltage to the lowest acceptable level to maximize battery life. Source: Microchip DS39626G, Section 2 (Electrical Characteristics).
Always bring out the ICSP pins (RB6/PGC = pin 26, RB7/PGD = pin 27) to a 5-pin or 6-pin programming header. Microchip recommends a 100-mil spaced 2x3 or single-row header for ICD/PICkit compatibility. Add MCLR pull-up (typically 10 kohm) and route the MCLR trace away from high-frequency PWM lines to avoid spurious resets. Source: Microchip application note TB087 (ICSP layout recommendations).
Do not assume PIC18LF2610 and PIC18F2610 are interchangeable at low VDD - the LF variant is required below 4.2 V. Also note: the LF variant still requires the configuration bits CONFIG1L (e.g., IESO, FCMEN) to be correctly set; an unprogrammed fresh device has LVP (low-voltage programming) enabled by default, which can interfere with RB5 if used as general I/O. Estimated: typical idle current for LF part at 3.3 V, 1 MHz is ~50 uA (datasheet figure).
Keep analog input traces (AN0-AN12) short and away from PWM and oscillator traces. Use a separate analog ground (AVSS, pin 28) tied to VSS at a single point. Add a 100 nF + 10 uF decoupling pair on AVSS/VDD if the 10-bit A/D drives ADC precision-critical sensors. Estimated: with 1.5 kohm source impedance, 12 TAD acquisition time gives ~10-bit accuracy at 40 MHz.
For the 28-SOIC (0.295 in / 7.50 mm body), the recommended land pattern follows JEDEC SOIC-28 standard: pads ~0.05 in wide x 0.085 in long with 0.050 in pitch. Use a four-layer PCB with a dedicated ground plane directly under the MCU, and route VDD power as a wide (>=20 mil) trace or small pour. Place the 40 MHz crystal (if used) within 0.25 in of OSC1/OSC2 with short traces and a ground guard ring.
규정 준수 정보
RoHS compliant per Microchip product page. Not AEC-Q100 qualified (use PIC18F26K80 or similar for automotive). LF variant indicates low-voltage operation 2.0-5.5 V (vs F variant 4.2-5.5 V).
