S9S08DV96F2CLL - 40MHz 96KB Flash 8-Bit MCU | NXP
부품 번호: S9S08DV96F2CLL ✗ 단종| 수량 | 단가 | 합계 |
|---|---|---|
| 1 | $0 | $0.00 |
| 10 | $0 | $0.00 |
| 100 | $0 | $0.00 |
| 500 | $0 | $0.00 |
| 1,000 | $0 | $0.00 |
S9S08DV96F2CLL 개요
A microcontroller is a programmable semiconductor that combines a processor core, memory, peripherals, and interfaces on one integrated circuit. This MCU belongs to the HCS08 family of 8-bit devices, where the S08 core executes embedded control logic and communicates with sensors, actuators, communication transceivers, and human-machine interfaces. Its 96KB flash provides nonvolatile program storage, while the integrated debug module supports development and troubleshooting.
The S9S08DV96F2CLL is specified in the supplied data as an automotive-qualified S08 MCU with a 40MHz clock and 100-LQFP package. The exact memory-map details, peripheral configuration, supply-voltage limits, GPIO count, CAN characteristics, and environmental ratings beyond the provided operating-temperature statement were not available in the verified data and are therefore not inferred here. The device should be selected only after checking the manufacturer datasheet for the exact package pinout, electrical limits, and peripheral assignments.
Its 8-bit architecture is appropriate for cost-sensitive embedded systems where moderate processing throughput is sufficient and deterministic control is more important than high-end computation. The 40MHz rating supports the device family’s embedded-control positioning, while 96KB flash offers substantially more program space than very small 8-bit controllers. The LQFP-100 package also exposes a comparatively large number of external connections for systems needing multiple I/O or communication resources.
Typical applications include automotive body and accessory controllers, CAN-based node modules, instrumentation, industrial automation, motor-control peripherals, and embedded gateway systems. A design should include appropriate decoupling, clock and reset consideration, peripheral-level protection, and validation against the specific automotive or industrial requirements of the finished product.
This page synthesizes verified manufacturer and distributor information, identifies unavailable technical fields explicitly, and provides practical selection guidance without inventing pricing, pin assignments, or standards compliance claims.
드롭인 대체품: S9S08DV96F2CLL — 동일 패키지, 핀 호환. PCB 재작업이 필요한 다른 패키지 부품은 제외됩니다.
이 시리즈의 변형
다음과 드롭인 호환되는 동일 시리즈 모델: S9S08DV96F2CLL (동일 폼 팩터 및 풋프린트) — 차이점: Package, Core, Instruction Set, Operating Temperature, Supply Voltage.
빠른 비교 도구 — 나란히 비교할 대체 부품을 선택하십시오:
S9S08DZ96F2VLF
✅ 드롭인✓ 재고 있음
$6.55 / 개
데이터시트 보기 →S9S08DZ32F2VLCR
✅ 드롭인✓ 재고 있음
$4.2 / 개
데이터시트 보기 →S9S08AW60E5MFGE
✅ 드롭인✓ 재고 있음
$6.05 / 개
데이터시트 보기 →S9S08AW32E5MPUE
✅ 드롭인✓ 재고 있음
$3.95 / 개
데이터시트 보기 →MC9S08DN32AMLC
✅ 드롭인✓ 재고 있음
$3.98 / 개
데이터시트 보기 →MC9S08DN32CLC
✅ 드롭인✓ 재고 있음
$4.25 / 개
데이터시트 보기 →S9S08DV96F2CLL 최대 정격 & 전기적 특성
| Product Type | 8-bit S08 microcontroller |
| Maximum CPU Frequency | 40 MHz |
| Flash Memory | 96 KB |
| Memory Organization | 96K x 8 bits |
| Core | HCS08 enhanced 8-bit core |
| 동작 온도 | -40°C to +85°C |
| Voltage Operation | Dual-voltage operation; exact limits not provided |
| Integrated Communication | CAN capability indicated in the supplied search data |
| Debug Support | Built-in debug module |
| 패키지 | 100-LQFP (14x14) |
| Package Family | LQFP |
| 실장 유형 | Surface mount |
| Automotive Qualification | Automotive qualified according to the supplied search data |
| 핀 수 | 100 pins |
S9S08DV96F2CLL lqfp 핀 구성 가이드
S9S08DV96F2CLL(lqfp 패키지)의 핀 구성입니다. 이 디지털 IC에는 GPIO, 통신 인터페이스(UART, SPI, I2C), 전원 핀이 포함되어 있습니다. 대체 핀 기능과 구성 옵션은 제조사 데이터시트를 참조하십시오. 임베디드 시스템 설계와 PCB 레이아웃에 필수적입니다.
다음에 대한 상세 핀아웃 데이터 없음: S9S08DV96F2CLL.
다음을 참조하십시오: 데이터시트 전체 핀 구성은 다음을 참조하십시오.
일반적인 애플리케이션
S9S08DV96F2CLL 적합 용도: 6 애플리케이션s: Automotive Body Control Node, CAN-Based Industrial Sensor Hub, Automotive Instrument Cluster Peripheral, Motor and Actuator Control, Industrial Gateway and Communications Module, Embedded Measurement and Control Platform.
Automotive Body Control Node
The S9S08DV96F2CLL fits an automotive body or accessory controller when an 8-bit MCU is sufficient and the design needs a stated -40°C to +85°C operating range. Its 40MHz S08 core can support deterministic control tasks, while 96KB flash provides room for protocol handlers, diagnostic logic, and application state machines. The supplied data indicates CAN-related functionality and automotive qualification positioning. In implementation, the MCU would connect to a suitable CAN transceiver, conditioning inputs, driving outputs, and managing reset and power sequencing. The main design trade-off is that an 8-bit architecture offers less processing headroom than a 32-bit MCU, so confirm all timing, diagnostic, and update requirements against the manufacturer datasheet.
추천
CAN-Based Industrial Sensor Hub
For an industrial sensor hub, the S9S08DV96F2CLL provides a compact 8-bit control platform with 96KB flash and a 40MHz core. That combination is appropriate for coordinating sensors, filtering inputs, maintaining operating counters, and forwarding measurements over a CAN network. The verified description identifies CAN capability, although transceiver requirements and exact CAN electrical parameters are not supplied. A practical design would use the MCU for protocol handling and local I/O management while an external transceiver converts logical CAN signals to differential bus levels. Validate timing under the worst-case bus load, define fault behavior for bus-off conditions, and verify the complete electrical specification before production.
추천
Automotive Instrument Cluster Peripheral
The S9S08DV96F2CLL can be used as a peripheral controller adjacent to an instrument cluster when the task is limited to input conditioning, switch handling, indicator control, or communication support. Its 100-LQFP package provides access to a comparatively large pin count, and 96KB flash allows firmware to include calibration data, diagnostics, and communication routines. The 40MHz S08 core is suitable for moderate real-time control rather than graphics rendering. Design the interface to match the cluster's voltage domains, protect external inputs from automotive transients, and isolate communication appropriately. Confirm pin multiplexing and timing from the official datasheet because those details were not present in the supplied search data.
추천
Motor and Actuator Control
The S9S08DV96F2CLL is a candidate for small motor, solenoid, or actuator control modules where control logic, protection, and communication must coexist in one device. The 40MHz core provides more timing headroom than a basic low-end 8-bit controller, while 96KB flash can hold motion sequences and diagnostic logic. The supplied data does not specify PWM resolution, analog channels, timer architecture, or current-drive capability, so the MCU is more appropriately treated as the supervisory controller than as a direct high-current power stage. Use external drivers and protection circuits, and verify timer, ADC, and pin-mux requirements before selecting it for a new motor-control design.
추천
Industrial Gateway and Communications Module
The S9S08DV96F2CLL can serve as a local communications controller in an industrial gateway when the product needs modest protocol processing, persistent configuration, and deterministic peripheral management. Its 96KB flash is useful for stack configuration and application firmware, and the stated dual-voltage operation may assist systems with multiple supply domains. The MCU should remain responsible for framing, status monitoring, configuration, and supervisory I/O rather than unrestricted high-throughput networking. Exact serial-interface ratings, memory protection features, and package-level pin assignments must be checked in the manufacturer documentation. For production, also validate reset behavior, brownout response, watchdog strategy, and field-update requirements.
추천
Embedded Measurement and Control Platform
The S9S08DV96F2CLL is suitable for a measurement-and-control platform when the system requires an 8-bit controller with more flash and clock capability than a minimal logic-oriented MCU. The 40MHz core can coordinate sampling control, data preparation, local storage, and supervisory communications, while 96KB flash supports calibration tables and application routines. The supplied data does not confirm ADC resolution, sampling rate, comparator features, or timer channels; these are essential constraints for instrumentation. Use the MCU only after confirming analog and timing requirements, and place appropriate signal conditioning, filtering, and grounding around the measurement front end. This arrangement is best for compact embedded controllers rather than high-resolution data acquisition systems.
추천
추천 제품 요약
엔지니어링 참조 데이터: S9S08DV96F2CLL — 비교, 설계 지침 및 규정 준수 정보.
선택 가이드
대체품과의 비교
| 파라미터 | 이 제품 | S9S08DZ96F2VLF | S9S08DZ32F2VLCR | S9S08AW60E5MFGE | S9S08AW32E5MPUE | MC9S08DN32AMLC |
|---|---|---|---|---|---|---|
| Package | 100-LQFP (14x14) | 100-LQFP (14x14), stated | 100-LQFP (14x14), stated | 100-LQFP (14x14), stated | 100-LQFP (14x14), stated | 100-LQFP (14x14), stated |
| Brand | NXP Semiconductors | NXP Semiconductors | NXP Semiconductors | NXP Semiconductors | NXP Semiconductors | Freescale Semiconductor |
| CPU Architecture | 8-bit S08 | S08 family; exact core details not verified | S08 family; exact core details not verified | S08 family; exact core details not verified | S08 family; exact core details not verified | HCS08 family; exact core details not verified |
주요 차별점
- 40MHz S08 processing capability (vs S9S08DZ32F2VLCR)
- 96KB flash memory (vs S9S08AW60E5MFGE)
- Broad stated operating range (vs S9S08DZ96F2VLF)
- Integrated development support (vs MC9S08DN32AMLC)
설계 노트
Do not design the supply rails until the exact S9S08DV96F2CLL electrical limits are confirmed in the NXP datasheet. The verified data confirms dual-voltage operation but does not provide the valid range, absolute maximum ratings, startup requirements, or brownout behavior. Add the manufacturer-recommended decoupling at each supply pin and account for voltage sequencing between any external CAN transceiver, sensor, and MCU. A power review should include steady-state current, transient response, and worst-case I/O loading rather than nominal current alone.
Treat the 100-LQFP footprint as a fine-pitch mixed-signal layout problem even though the target application is primarily digital. Place decoupling capacitors close to the relevant supply pins, route high-current and switching-node connections away from reset and debug traces, and provide a controlled ground return for any analog measurement circuitry. Because the verified data does not include a pinout, do not assign pins from memory; cross-check every land and escape route against the official package drawing before fabrication.
The supplied search results establish that the part is an 8-bit S08 MCU, but they do not establish a drop-in replacement or a complete pin-compatible family relationship. Before substituting an alternative, verify package dimensions, pin names, power pins, debug signals, CAN functions, flash organization, voltage limits, clock setup, reset polarity, and software map. Also confirm lifecycle status, qualification documentation, and authorized sourcing. A similarly named S08 part may require PCB changes, driver changes, or firmware migration.
For CAN-connected or automotive-adjacent circuits, keep the MCU and transceiver interface geometry predictable. Separate transceiver supply and return current from sensitive MCU supplies, use a continuous ground reference where appropriate, and route debug or programming signals away from potential noise sources. The supplied data does not provide CAN timing or transceiver recommendations, so these layout actions are general engineering practices rather than manufacturer-specific guarantees. Validate signal integrity with the final stack-up, connector, cable, and bus topology.
The verified operating-temperature range is -40°C to +85°C, but no power dissipation, thermal resistance, or maximum junction-temperature data was supplied. Estimate total device dissipation from the actual core, I/O, peripheral, and supply currents using the final firmware workload, then compare it with the manufacturer’s thermal limits. Keep the LQFP adequately soldered and inspect assembly quality, because thermal performance depends on the PCB copper area, solder mask, vias, adjacent heat sources, and enclosure—not only the nominal ambient temperature.
규정 준수 정보
The supplied search data states automotive qualification but does not provide formal RoHS, REACH, AEC-Q100, lead-free, halogen-free, or conflict-minerals declarations. Verify these attributes with NXP or the current manufacturer documentation before release.
