XC95108-10PC84C - 108-Macrocell 5V In-System CPLD | AMD Xilinx
부품 번호: XC95108-10PC84C ✗ 단종XC95108-10PC84C 개요
A CPLD is a user-programmable digital logic device in which each macrocell contains a programmable AND/OR logic array plus a flip-flop. Because the logic paths are short and deterministic, a CPLD gives predictable, single-cycle propagation delays and a simple timing model, which is exactly what designers need when a design must meet a fixed bus or handshake timing budget without deep timing analysis.
Key features include 10 ns maximum pin-to-pin logic delay for the -10 speed grade, 5 ns pin-to-pin logic delays on all pins with fCNT operation up to 125 MHz, in-system programmability with a minimum of 10,000 program/erase cycles, and support for parallel programming of multiple XC9500 devices on the same board. The device accepts a 4.75 V to 5.25 V internal supply range and is programmed through 5 V in-system programming, so no dedicated programmer or socket is required once the board is built.
Internally, the XC9500 architecture uses a uniform, non-volatile Fast FLASH configuration memory that is mapped into the logic array, giving the device deterministic, repeatable startup behaviour and allowing field reconfiguration of a deployed board through the same 5 V rails that carry system data. The XC95108 is offered in 84-pin PLCC, 68-pin PLCC, 84-pin PQFP and 100-pin TQFP packages, so the PLCC-84 footprint is shared with several family members for footprint-compatible board reuse.
Typical applications include ISA and PCI bus interface glue logic, multi-drop RS-485 and industrial field-bus conditioning, stepper and relay sequencing in legacy motion controllers, power-supply sequencing and battery-backed monitoring, and long-life test and measurement equipment where the original 5 V design must be maintained rather than redesigned.
When designing around this device, note that it is a legacy 5 V part: outputs are not 3.3 V tolerant, the 0 C to +70 C window excludes industrial temperature grades, and the 5 V in-system programming pins must be routed to accessible test pads or a connector so firmware can be updated after assembly. Plan the I/O budget carefully, since 69 usable I/O in PLCC-84 leaves the remaining pins for power, ground, configuration and control.
This page brings together the manufacturer specification summary, verified distributor availability listings, family-level drop-in alternatives in the same PLCC-84 footprint, and practical design notes that are not reproduced in the original datasheet, so engineers can evaluate a migration path without re-deriving the whole device family from scratch.
드롭인 대체품: XC95108-10PC84C — 동일 패키지, 핀 호환. PCB 재작업이 필요한 다른 패키지 부품은 제외됩니다.
이 시리즈의 변형
다음과 드롭인 호환되는 동일 시리즈 모델: XC95108-10PC84C (동일 폼 팩터 및 풋프린트) — 차이점: Usable Gates, RoHS Status, Device Type, Number of Macrocells, Operating Temperature.
XC95108-20PC84C
✅ 드롭인📋 참조 대체품 (카탈로그에 없음)
XC9572-15PC84C
✅ 드롭인📋 참조 대체품 (카탈로그에 없음)
XC9572-10PC84C
✅ 드롭인 ⚠️ 사양 미검증가격 문의
데이터시트 보기 →XC95108L-10PC84C
✅ 드롭인 ⚠️ 사양 미검증📋 참조 대체품 (카탈로그에 없음)
XC95144-10PC84C
✅ 드롭인 ⚠️ 사양 미검증📋 참조 대체품 (카탈로그에 없음)
XC95108-10PC84C 최대 정격 & 전기적 특성
| Device Type | In-system programmable CPLD (XC9500 5 V family) |
| Macrocells | 108 |
| Usable Gates | 2,400 |
| User I/O Pins | 69 |
| Pin Count / Package | 84 pins, PLCC (J-lead, 29.31 x 29.31 mm) |
| 실장 유형 | Surface Mount |
| Internal Supply Voltage | 4.75 V to 5.25 V |
| Max Pin-to-Pin Logic Delay (tpd) | 10 ns (-10 speed grade) |
| Pin-to-Pin Logic Delay (best case) | 5 ns on all pins, fCNT to 125 MHz |
| 동작 온도 | 0 C to +70 C (TA) |
| Programmable Type | In-system programmable, minimum 10,000 program/erase cycles |
| Technology | Advanced CMOS 0.5 um Fast FLASH |
| Configuration Memory | Non-volatile Fast FLASH, supports parallel programming of multiple XC9500 devices |
| RoHS 상태 | RoHS non-compliant |
| Lead Free Status | Contains lead |
| Part Status | Obsolete (legacy 5 V CPLD generation) |
| Programming | 5 V in-system programming |
XC95108-10PC84C 5 ns on all pins, fcnt to 125 mhz 핀 구성 가이드
XC95108-10PC84C(5 ns on all pins, fcnt to 125 mhz 패키지)의 핀 구성입니다. 이 디지털 IC에는 GPIO, 통신 인터페이스(UART, SPI, I2C), 전원 핀이 포함되어 있습니다. 대체 핀 기능과 구성 옵션은 제조사 데이터시트를 참조하십시오. 임베디드 시스템 설계와 PCB 레이아웃에 필수적입니다.
다음에 대한 상세 핀아웃 데이터 없음: XC95108-10PC84C.
다음을 참조하십시오: 데이터시트 전체 핀 구성은 다음을 참조하십시오.
일반적인 애플리케이션
XC95108-10PC84C 적합 용도: 6 애플리케이션s: Legacy ISA / PCI Bus Interface Glue Logic, Multi-Drop RS-485 and Field-Bus Conditioning, Stepper Motor and Relay Sequencing Control, 5V Power Supply Sequencing and System Supervision, Embedded Microcontroller Coprocessor and Bus Glue, Long-Life Test and Measurement Equipment Retrofit.
Legacy ISA / PCI Bus Interface Glue Logic
The XC95108-10PC84C is a natural fit for ISA and PCI peripheral cards of the type still found in industrial PCs, test benches and instrumentation. With 108 macrocells (about 2,400 usable gates) and 69 user I/O pins, it can absorb address decode, command strobes, buffer arbitration and FIFO control that would otherwise consume several 74-series logic families. The 10 ns maximum pin-to-pin delay of the -10 speed grade keeps bus strobe-to-acknowledgement paths short, and 5 V in-system programming means a card can be reconfigured in the field through accessible test pads without a socketed programmer.
추천
Multi-Drop RS-485 and Field-Bus Conditioning
In multi-drop industrial communication nodes, the XC95108-10PC84C can implement bus arbitration, direction control, CRC generation and bit-stuffing framing around a 5 V transceiver. Its deterministic single-cycle timing makes it easy to meet the timing budget of legacy field-bus protocols, where byte-level framing must be completed inside a fixed timer interval. The 69 available I/O pins suit nodes that carry several channels of digital status alongside the bus, and the 0 C to +70 C rating covers indoor enclosure temperatures. For harsher factory environments, a wider-temperature 3.3 V XC9500XL or CoolRunner XLC part is preferred.
추천
Stepper Motor and Relay Sequencing Control
The XC95108-10PC84C suits open-loop stepper and relay sequencing blocks in legacy motion controllers and industrial machinery, where a small microcontroller is either absent or only supervises motion. Each macrocell's flip-flop and product-term array allows precise pulse-width, direction and interlock logic for step generation, with 108 macrocells giving room for acceleration tables, limit-switch decoding and homing sequences. The 10 ns delay class keeps step-to-step jitter low, and the 5 V supply matches legacy stepper driver enable and opto-isolator input stages. Because the operating range is 0 C to +70 C, enclosure heating or a temperature-rated replacement should be considered near motors.
추천
5V Power Supply Sequencing and System Supervision
In 5 V-only systems with multiple rails, the XC95108-10PC84C can implement power-supply sequencing, rail monitoring, watchdog heartbeat and reset generation without adding a microcontroller to a simple board. Each macrocell can latch a rail-good level and hold the next enable until the previous rail settles, which is exactly the deterministic behaviour a sequencer needs. With 69 I/O, a single device can supervise several supplies plus fault inputs, and the 5 V in-system programming path lets a technician reload the sequencing table after a field fault. Use the device's non-volatile Fast FLASH configuration so the sequence survives power cycling without a boot loader.
추천
Embedded Microcontroller Coprocessor and Bus Glue
When a legacy 8-bit microcontroller such as an 8051-class part lacks address space or port count, the XC95108-10PC84C can act as a coprocessor handling address decode, port expansion, timing generation and data buffering. The 108 macrocells and 69 I/O pins allow a wide peripheral bus to be emulated with fixed-cycle access, while the 10 ns delay class keeps interrupt acknowledge and DMA-style handshake windows comfortable. The device's 5 V in-system programming also enables a shared programming header that can load both the coprocessor logic and the host firmware in one manufacturing step, simplifying factory test and field upgrades.
추천
Long-Life Test and Measurement Equipment Retrofit
The XC95108-10PC84C is widely encountered inside older test and measurement platforms - switch control, relay matrices, trigger routing and front-panel state machines - where a board must be repaired rather than redesigned. Because the device stores its configuration in non-volatile Fast FLASH, a replacement can be programmed in-circuit to reproduce the original behaviour, which shortens repair turnaround considerably. The 69 I/O pins suit dense point matrices and status buses, and the 0 C to +70 C range covers instrument-room conditions. For new instrument development, pair the same functional block with a modern 3.3 V CPLD such as the XC2C128 or CoolRunner XLC family.
추천
추천 제품 요약
엔지니어링 참조 데이터: XC95108-10PC84C — 비교, 설계 지침 및 규정 준수 정보.
선택 가이드
대체품과의 비교
| 파라미터 | 이 제품 | XC95108-20PC84C | XC9572-15PC84C | XC9572-10PC84C | XC95144-10PC84C |
|---|---|---|---|---|---|
| Package | 84-pin PLCC (J-lead) | 84-pin PLCC (J-lead) - same | 84-pin PLCC (J-lead) - same | 84-pin PLCC (J-lead) - same | 84-pin PLCC (J-lead) - same |
| Brand | AMD (Xilinx XC9500 family) | AMD (Xilinx XC9500 family) | AMD (Xilinx XC9500 family) | AMD (Xilinx XC9500 family) | AMD (Xilinx XC9500 family) |
| Macrocells | 108 (approx. 2,400 usable gates) | 108 (approx. 2,400 usable gates) | 72 - 33% lower logic capacity | 72 - 33% lower logic capacity | 144 - 33% higher logic capacity |
| User I/O Pins | 69 | 69 | 69 | 69 | 69 |
| Max Pin-to-Pin Logic Delay (tpd) | 10 ns | 20 ns - 100% slower | 15 ns - 50% slower | 10 ns - same speed grade | 10 ns - same speed grade |
| Internal Supply Voltage | 4.75 V to 5.25 V (5 V) | 4.75 V to 5.25 V (5 V) | 5 V family | 5 V family | 5 V family |
| Programming | 5 V in-system programmable, min 10,000 program/erase cycles | 5 V in-system programmable | 5 V in-system programmable | 5 V in-system programmable | 5 V in-system programmable |
| Operating Temperature | 0 C to +70 C (commercial) | 0 C to +70 C (commercial) | 0 C to +70 C (commercial) | 0 C to +70 C (commercial) | 0 C to +70 C (commercial) |
| Technology | Advanced CMOS 0.5 um Fast FLASH | Advanced CMOS 0.5 um Fast FLASH | Advanced CMOS 0.5 um Fast FLASH | Advanced CMOS 0.5 um Fast FLASH | Advanced CMOS 0.5 um Fast FLASH |
| Lifecycle Status | Obsolete | Obsolete (legacy 5 V generation) | Obsolete (legacy 5 V generation) | Obsolete (legacy 5 V generation) | Obsolete (legacy 5 V generation) |
| RoHS Compliance | RoHS non-compliant (contains lead) | RoHS non-compliant | RoHS non-compliant | RoHS non-compliant | RoHS non-compliant |
주요 차별점
- Largest logic array in the 84-pin PLCC 5 V footprint (vs XC9572-15PC84C)
- Fastest speed grade available in the 5 V XC9500 PLCC-84 family (vs XC95108-20PC84C)
- Extra macrocell headroom for expansion without a footprint change (vs XC9572-10PC84C)
- Fully in-system programmable for field updates on legacy boards (vs XC9572-15PC84C)
설계 노트
The 84-pin PLCC body measures 29.31 mm x 29.31 mm and uses J-shaped leads, so the socket-style footprint needs generous clearance for a PLCC socket if the board is to be reworked. Reserve a 1.0 mm to 1.27 mm grid of pads on a 0.1 inch pitch with the correct J-lead land pattern, and keep tall components and heat sinks away from the J-lead exit side. The exposed underside of a PLCC is not a thermal pad, so copper pours beneath the device add little more than a small heat-spreading effect.
Estimated: the XC9500 architecture consumes substantially more power than a 3.3 V CPLD because the internal supply is 5 V and the configuration cells are large. Budget 5 V rails with at least 10 percent headroom for inrush during in-system programming, and decouple each VCC pin group with a 0.1 uF ceramic capacitor plus a bulk electrolytic near the array. Because 5 V in-system programming draws additional current while erasing and writing Flash cells, avoid placing the programming test pads behind a series ferrite bead that would limit current during a field update.
Do not treat this device as a modern 3.3 V part: its I/O drive is 5 V CMOS and outputs are not 3.3 V tolerant, so any 3.3 V signal connected to an input or output can be over-stressed or fail to meet VIH/VIL thresholds. Also note the 0 C to +70 C commercial rating, which excludes most factory-floor and automotive environments. Finally, because the macrocell count differs across the XC9500 family, verify that a substituted part still fits the design in the programming tool before committing to a replacement.
Route the 5 V in-system programming pins (TCLK, TDI, TMS, TDO and the configuration control) to a dedicated header or pogo-pad block so the board can be reprogrammed in circuit after assembly or in the field. Keep these nets away from high-speed or high-current switching nodes, and provide a defined programming-mode strap so the device enters configuration mode predictably. Because the XC9500 family supports parallel programming of multiple devices, shared programming buses are acceptable when the per-device select logic is unambiguous.
With a 10 ns maximum pin-to-pin delay and operation up to 125 MHz fCNT, edge rates are fast enough that board-level return paths matter. Provide a continuous ground plane under the device, avoid splitting the plane beneath the package, and terminate any externally driven clock or latch input with a short stub and a source-terminating resistor. The macrocell architecture is deterministic, but long unprotected traces can still degrade setup margin against the 10 ns grade, so re-check critical paths with the timing report rather than relying on device delay numbers alone.
규정 준수 정보
The XC95108-10PC84C is listed as RoHS non-compliant and containing lead, consistent with the legacy 5 V XC9500 generation. AEC-Q100 qualification does not apply to this commercial 0 C to +70 C device, and no REACH, halogen-free or conflict-minerals statement is published for the part.