XC95108-10PC84C - 108-Macrocell 5V In-System CPLD | AMD Xilinx
MPN: XC95108-10PC84C ✗ End of LifeXC95108-10PC84C Overview
A CPLD is a user-programmable digital logic device in which each macrocell contains a programmable AND/OR logic array plus a flip-flop. Because the logic paths are short and deterministic, a CPLD gives predictable, single-cycle propagation delays and a simple timing model, which is exactly what designers need when a design must meet a fixed bus or handshake timing budget without deep timing analysis.
Key features include 10 ns maximum pin-to-pin logic delay for the -10 speed grade, 5 ns pin-to-pin logic delays on all pins with fCNT operation up to 125 MHz, in-system programmability with a minimum of 10,000 program/erase cycles, and support for parallel programming of multiple XC9500 devices on the same board. The device accepts a 4.75 V to 5.25 V internal supply range and is programmed through 5 V in-system programming, so no dedicated programmer or socket is required once the board is built.
Internally, the XC9500 architecture uses a uniform, non-volatile Fast FLASH configuration memory that is mapped into the logic array, giving the device deterministic, repeatable startup behaviour and allowing field reconfiguration of a deployed board through the same 5 V rails that carry system data. The XC95108 is offered in 84-pin PLCC, 68-pin PLCC, 84-pin PQFP and 100-pin TQFP packages, so the PLCC-84 footprint is shared with several family members for footprint-compatible board reuse.
Typical applications include ISA and PCI bus interface glue logic, multi-drop RS-485 and industrial field-bus conditioning, stepper and relay sequencing in legacy motion controllers, power-supply sequencing and battery-backed monitoring, and long-life test and measurement equipment where the original 5 V design must be maintained rather than redesigned.
When designing around this device, note that it is a legacy 5 V part: outputs are not 3.3 V tolerant, the 0 C to +70 C window excludes industrial temperature grades, and the 5 V in-system programming pins must be routed to accessible test pads or a connector so firmware can be updated after assembly. Plan the I/O budget carefully, since 69 usable I/O in PLCC-84 leaves the remaining pins for power, ground, configuration and control.
This page brings together the manufacturer specification summary, verified distributor availability listings, family-level drop-in alternatives in the same PLCC-84 footprint, and practical design notes that are not reproduced in the original datasheet, so engineers can evaluate a migration path without re-deriving the whole device family from scratch.
Drop-in alternatives for XC95108-10PC84C — same package, pin-to-pin compatible. Different-package parts requiring PCB rework are excluded.
Variants in this series
Same-series models that are drop-in compatible with XC95108-10PC84C (same form factor and footprint) — differing in Usable Gates, RoHS Status, Device Type, Number of Macrocells, Operating Temperature.
XC95108-20PC84C
✅ Drop-In📋 Reference alternative (not in catalog)
XC9572-15PC84C
✅ Drop-In📋 Reference alternative (not in catalog)
XC9572-10PC84C
✅ Drop-In ⚠️ Specs UnverifiedContact for price
View Datasheet →XC95108L-10PC84C
✅ Drop-In ⚠️ Specs Unverified📋 Reference alternative (not in catalog)
XC95144-10PC84C
✅ Drop-In ⚠️ Specs Unverified📋 Reference alternative (not in catalog)
XC95108-10PC84C Maximum Ratings & Electrical Characteristics
| Device Type | In-system programmable CPLD (XC9500 5 V family) |
| Macrocells | 108 |
| Usable Gates | 2,400 |
| User I/O Pins | 69 |
| Pin Count / Package | 84 pins, PLCC (J-lead, 29.31 x 29.31 mm) |
| Mounting Type | Surface Mount |
| Internal Supply Voltage | 4.75 V to 5.25 V |
| Max Pin-to-Pin Logic Delay (tpd) | 10 ns (-10 speed grade) |
| Pin-to-Pin Logic Delay (best case) | 5 ns on all pins, fCNT to 125 MHz |
| Operating Temperature | 0 C to +70 C (TA) |
| Programmable Type | In-system programmable, minimum 10,000 program/erase cycles |
| Technology | Advanced CMOS 0.5 um Fast FLASH |
| Configuration Memory | Non-volatile Fast FLASH, supports parallel programming of multiple XC9500 devices |
| RoHS Status | RoHS non-compliant |
| Lead Free Status | Contains lead |
| Part Status | Obsolete (legacy 5 V CPLD generation) |
| Programming | 5 V in-system programming |
XC95108-10PC84C 5 ns on all pins, fcnt to 125 mhz Pin Configuration Guide
Pin configuration for XC95108-10PC84C (5 ns on all pins, fcnt to 125 mhz package). This digital IC includes GPIO, communication interfaces (UART, SPI, I2C), and power pins. Refer to the manufacturer datasheet for alternate pin functions and configuration options. Essential for embedded system design and PCB layout.
No detailed pinout data available for XC95108-10PC84C.
Refer to the datasheet for full pin configuration.
Typical Applications
XC95108-10PC84C is suitable for 6 applications: Legacy ISA / PCI Bus Interface Glue Logic, Multi-Drop RS-485 and Field-Bus Conditioning, Stepper Motor and Relay Sequencing Control, 5V Power Supply Sequencing and System Supervision, Embedded Microcontroller Coprocessor and Bus Glue, Long-Life Test and Measurement Equipment Retrofit.
Legacy ISA / PCI Bus Interface Glue Logic
The XC95108-10PC84C is a natural fit for ISA and PCI peripheral cards of the type still found in industrial PCs, test benches and instrumentation. With 108 macrocells (about 2,400 usable gates) and 69 user I/O pins, it can absorb address decode, command strobes, buffer arbitration and FIFO control that would otherwise consume several 74-series logic families. The 10 ns maximum pin-to-pin delay of the -10 speed grade keeps bus strobe-to-acknowledgement paths short, and 5 V in-system programming means a card can be reconfigured in the field through accessible test pads without a socketed programmer.
Recommended
Multi-Drop RS-485 and Field-Bus Conditioning
In multi-drop industrial communication nodes, the XC95108-10PC84C can implement bus arbitration, direction control, CRC generation and bit-stuffing framing around a 5 V transceiver. Its deterministic single-cycle timing makes it easy to meet the timing budget of legacy field-bus protocols, where byte-level framing must be completed inside a fixed timer interval. The 69 available I/O pins suit nodes that carry several channels of digital status alongside the bus, and the 0 C to +70 C rating covers indoor enclosure temperatures. For harsher factory environments, a wider-temperature 3.3 V XC9500XL or CoolRunner XLC part is preferred.
Recommended
Stepper Motor and Relay Sequencing Control
The XC95108-10PC84C suits open-loop stepper and relay sequencing blocks in legacy motion controllers and industrial machinery, where a small microcontroller is either absent or only supervises motion. Each macrocell's flip-flop and product-term array allows precise pulse-width, direction and interlock logic for step generation, with 108 macrocells giving room for acceleration tables, limit-switch decoding and homing sequences. The 10 ns delay class keeps step-to-step jitter low, and the 5 V supply matches legacy stepper driver enable and opto-isolator input stages. Because the operating range is 0 C to +70 C, enclosure heating or a temperature-rated replacement should be considered near motors.
Recommended
5V Power Supply Sequencing and System Supervision
In 5 V-only systems with multiple rails, the XC95108-10PC84C can implement power-supply sequencing, rail monitoring, watchdog heartbeat and reset generation without adding a microcontroller to a simple board. Each macrocell can latch a rail-good level and hold the next enable until the previous rail settles, which is exactly the deterministic behaviour a sequencer needs. With 69 I/O, a single device can supervise several supplies plus fault inputs, and the 5 V in-system programming path lets a technician reload the sequencing table after a field fault. Use the device's non-volatile Fast FLASH configuration so the sequence survives power cycling without a boot loader.
Recommended
Embedded Microcontroller Coprocessor and Bus Glue
When a legacy 8-bit microcontroller such as an 8051-class part lacks address space or port count, the XC95108-10PC84C can act as a coprocessor handling address decode, port expansion, timing generation and data buffering. The 108 macrocells and 69 I/O pins allow a wide peripheral bus to be emulated with fixed-cycle access, while the 10 ns delay class keeps interrupt acknowledge and DMA-style handshake windows comfortable. The device's 5 V in-system programming also enables a shared programming header that can load both the coprocessor logic and the host firmware in one manufacturing step, simplifying factory test and field upgrades.
Recommended
Long-Life Test and Measurement Equipment Retrofit
The XC95108-10PC84C is widely encountered inside older test and measurement platforms - switch control, relay matrices, trigger routing and front-panel state machines - where a board must be repaired rather than redesigned. Because the device stores its configuration in non-volatile Fast FLASH, a replacement can be programmed in-circuit to reproduce the original behaviour, which shortens repair turnaround considerably. The 69 I/O pins suit dense point matrices and status buses, and the 0 C to +70 C range covers instrument-room conditions. For new instrument development, pair the same functional block with a modern 3.3 V CPLD such as the XC2C128 or CoolRunner XLC family.
Recommended
Recommended Products Summary
Engineering reference data for XC95108-10PC84C — comparison, design guidance, and compliance information.
Selection Guide
Comparison with Alternatives
| Parameter | This Product | XC95108-20PC84C | XC9572-15PC84C | XC9572-10PC84C | XC95144-10PC84C |
|---|---|---|---|---|---|
| Package | 84-pin PLCC (J-lead) | 84-pin PLCC (J-lead) - same | 84-pin PLCC (J-lead) - same | 84-pin PLCC (J-lead) - same | 84-pin PLCC (J-lead) - same |
| Brand | AMD (Xilinx XC9500 family) | AMD (Xilinx XC9500 family) | AMD (Xilinx XC9500 family) | AMD (Xilinx XC9500 family) | AMD (Xilinx XC9500 family) |
| Macrocells | 108 (approx. 2,400 usable gates) | 108 (approx. 2,400 usable gates) | 72 - 33% lower logic capacity | 72 - 33% lower logic capacity | 144 - 33% higher logic capacity |
| User I/O Pins | 69 | 69 | 69 | 69 | 69 |
| Max Pin-to-Pin Logic Delay (tpd) | 10 ns | 20 ns - 100% slower | 15 ns - 50% slower | 10 ns - same speed grade | 10 ns - same speed grade |
| Internal Supply Voltage | 4.75 V to 5.25 V (5 V) | 4.75 V to 5.25 V (5 V) | 5 V family | 5 V family | 5 V family |
| Programming | 5 V in-system programmable, min 10,000 program/erase cycles | 5 V in-system programmable | 5 V in-system programmable | 5 V in-system programmable | 5 V in-system programmable |
| Operating Temperature | 0 C to +70 C (commercial) | 0 C to +70 C (commercial) | 0 C to +70 C (commercial) | 0 C to +70 C (commercial) | 0 C to +70 C (commercial) |
| Technology | Advanced CMOS 0.5 um Fast FLASH | Advanced CMOS 0.5 um Fast FLASH | Advanced CMOS 0.5 um Fast FLASH | Advanced CMOS 0.5 um Fast FLASH | Advanced CMOS 0.5 um Fast FLASH |
| Lifecycle Status | Obsolete | Obsolete (legacy 5 V generation) | Obsolete (legacy 5 V generation) | Obsolete (legacy 5 V generation) | Obsolete (legacy 5 V generation) |
| RoHS Compliance | RoHS non-compliant (contains lead) | RoHS non-compliant | RoHS non-compliant | RoHS non-compliant | RoHS non-compliant |
Key Differentiators
- Largest logic array in the 84-pin PLCC 5 V footprint (vs XC9572-15PC84C)
- Fastest speed grade available in the 5 V XC9500 PLCC-84 family (vs XC95108-20PC84C)
- Extra macrocell headroom for expansion without a footprint change (vs XC9572-10PC84C)
- Fully in-system programmable for field updates on legacy boards (vs XC9572-15PC84C)
Design Notes
The 84-pin PLCC body measures 29.31 mm x 29.31 mm and uses J-shaped leads, so the socket-style footprint needs generous clearance for a PLCC socket if the board is to be reworked. Reserve a 1.0 mm to 1.27 mm grid of pads on a 0.1 inch pitch with the correct J-lead land pattern, and keep tall components and heat sinks away from the J-lead exit side. The exposed underside of a PLCC is not a thermal pad, so copper pours beneath the device add little more than a small heat-spreading effect.
Estimated: the XC9500 architecture consumes substantially more power than a 3.3 V CPLD because the internal supply is 5 V and the configuration cells are large. Budget 5 V rails with at least 10 percent headroom for inrush during in-system programming, and decouple each VCC pin group with a 0.1 uF ceramic capacitor plus a bulk electrolytic near the array. Because 5 V in-system programming draws additional current while erasing and writing Flash cells, avoid placing the programming test pads behind a series ferrite bead that would limit current during a field update.
Do not treat this device as a modern 3.3 V part: its I/O drive is 5 V CMOS and outputs are not 3.3 V tolerant, so any 3.3 V signal connected to an input or output can be over-stressed or fail to meet VIH/VIL thresholds. Also note the 0 C to +70 C commercial rating, which excludes most factory-floor and automotive environments. Finally, because the macrocell count differs across the XC9500 family, verify that a substituted part still fits the design in the programming tool before committing to a replacement.
Route the 5 V in-system programming pins (TCLK, TDI, TMS, TDO and the configuration control) to a dedicated header or pogo-pad block so the board can be reprogrammed in circuit after assembly or in the field. Keep these nets away from high-speed or high-current switching nodes, and provide a defined programming-mode strap so the device enters configuration mode predictably. Because the XC9500 family supports parallel programming of multiple devices, shared programming buses are acceptable when the per-device select logic is unambiguous.
With a 10 ns maximum pin-to-pin delay and operation up to 125 MHz fCNT, edge rates are fast enough that board-level return paths matter. Provide a continuous ground plane under the device, avoid splitting the plane beneath the package, and terminate any externally driven clock or latch input with a short stub and a source-terminating resistor. The macrocell architecture is deterministic, but long unprotected traces can still degrade setup margin against the 10 ns grade, so re-check critical paths with the timing report rather than relying on device delay numbers alone.
Compliance Information
The XC95108-10PC84C is listed as RoHS non-compliant and containing lead, consistent with the legacy 5 V XC9500 generation. AEC-Q100 qualification does not apply to this commercial 0 C to +70 C device, and no REACH, halogen-free or conflict-minerals statement is published for the part.