MAX3243CPWRG4 - 250kbps RS-232 | Texas Instruments
MPN: MAX3243CPWRG4 ✓ AktifMAX3243CPWRG4 Ringkasan
An RS-232 interface IC converts logic-level digital signals into RS-232-compatible line levels and converts received line signals back into logic levels. The MAX3243 belongs to the interface IC hierarchy, where it bridges a host controller or processor with a physical serial port. Its multichannel architecture supports several data paths on one board while limiting the number of separate transceiver packages required. The 3 V to 5.5 V supply range accommodates both 3.3 V and 5 V system rails.
The principal electrical features are a 250 kbps maximum data rate and ±15 kV ESD protection rated to the HBM model. These characteristics make the transceiver relevant to equipment where a cable-connected port must withstand electrostatic discharge events. The receiver channels handle incoming serial data, while the driver channels convert outbound logic signals into RS-232 line levels. Commercial temperature grading, a gull-wing terminal form, and a rectangular TSSOP package support conventional surface-mount assembly.
The MAX3243 family is designed for systems that require multiple RS-232 channels without using a larger transceiver for only one or two links. Its low-voltage operation allows communication between modern embedded systems and legacy RS-232 equipment. Because RS-232 is a single-ended, bipolar signaling interface, correct grounding, cable routing, and protection implementation remain important when integrating the device into an industrial or externally accessible system.
Typical uses include industrial control consoles, laboratory test equipment, serial adapters, data loggers, point-of-sale systems, and embedded instrumentation. In a multiport design, several receiver inputs can monitor separate device connections while the drivers support outbound command channels. The 28-pin TSSOP package also makes the part suitable for compact single-board systems where through-hole RS-232 components would consume excessive area.
When laying out the PCB, place the transceiver near its connector and connector-protection components to minimize exposed high-voltage RS-232 traces. Keep logic-side routing separated from line-side routing, provide the required bypassing capacitors close to the supply pins, and observe the device's absolute-maximum ratings for the RS-232 pins. Verify external protection, grounding, and cable requirements for the completed system rather than relying on the IC's internal ESD rating alone.
This product page combines the manufacturer's device information with package, pinout, purchasing, replacement, and design guidance. It also identifies the verified same-family drop-in candidates and distinguishes them from options that would require different wiring or package changes, helping engineers evaluate an RS-232 design without treating every electrically similar transceiver as a true replacement.
Pilihan pengganti yang segera untuk MAX3243CPWRG4 — sama paket, pin-pin kompatibel. Bahagian paket yang berbeza memerlukan kerja ulang PCB diasingkan.
Varietas dalam siri ini
Model serupa yang kompatibel dengan pengganti yang segera MAX3243CPWRG4 (sama faktor bentuk dan kaki) — berbeza dalam ESD Protection, Maximum Data Rate, Product Type.
MAX3243CPW
✅ Masuk Drop-In ⚠️ Spesifikasi Tidak DisahkanHubungi untuk harga
Lihat Datasheet →MAX3243ECPWG4
✅ Masuk Drop-In ⚠️ Spesifikasi Tidak DisahkanHubungi untuk harga
Lihat Datasheet →MAX3243CPA+
✅ Masuk Drop-In ⚠️ Spesifikasi Tidak Disahkan📋 Alternatif rujukan (tidak dalam katalog)
MAX3243CPWRG4 Spesifikasi
| Product Type | Multichannel RS-232 line driver/receiver |
| Supply Voltage Range | 3 V to 5.5 V |
| Maximum Data Rate | 250 kbps |
| ESD Protection | ±15 kV HBM |
| Driver Channel Count | 3 channels |
| Receiver Channel Count | 3 channels |
| Transceiver Configuration | 3/5 transceiver |
| Interface Standard | RS-232 |
| Package Type | 28-pin TSSOP |
| Package Code | PW |
| Terminal Form | Gull wing |
| Package Shape | Rectangular |
| Temperature Grade | Commercial |
| Jenis Pemasangan | Surface mount |
| Number of Terminals | 28 |
| Datasheet Length | 16 pages |
Panduan Konfigurasi Pin MAX3243CPWRG4 rectangular
Konfigurasi pin untuk MAX3243CPWRG4 (rectangular pakai). Penomeran pin, fungsi, dan garis bentuk koneksi ditakrifkan dalam dokumen pengeluar. Rujuk dokumen untuk kebentuk dan pedoman pengasman.
Tiada data garisan pin yang diperoleh untuk MAX3243CPWRG4.
Rujuk kepada lembaran data untuk konfigurasi pin penuh.
Aplikasi Biasa
MAX3243CPWRG4 patut untuk 6 aplikasis: Industrial serial control console, Laboratory data acquisition equipment, Portable serial adapter, Data logger and telemetry equipment, Point-of-sale terminal interface, Embedded test and measurement system.
Industrial serial control console
The MAX3243CPWRG4 suits an industrial console that must communicate with several legacy RS-232 instruments. Its three driver channels can carry outbound commands, while three receiver channels can monitor device responses, reducing the number of transceivers required on the controller board. The 3 V to 5.5 V supply range supports modern embedded control logic, and the 250 kbps rate is appropriate for moderate-speed command and telemetry traffic. Place the IC near the DB9 or connector circuitry, keep logic and line-side traces separated, and use suitable external protection when ports are exposed to industrial cabling.
Disebarkan
Laboratory data acquisition equipment
The MAX3243CPWRG4 can connect a laboratory instrument or data-acquisition unit to a computer or controller through multiple RS-232 ports. The 250 kbps data rate accommodates typical command transfers and moderate measurement streams, while the three-driver and three-receiver arrangement supports bidirectional instruments without requiring separate driver and receiver packages. Its 28-pin TSSOP package reduces board area compared with larger through-hole implementations. Designers should use the manufacturer's application circuit as a reference for bypassing, enable or shutdown behavior, and connector interfacing, particularly when long external cables increase electrostatic-discharge risk.
Disebarkan
Portable serial adapter
The MAX3243CPWRG4 is appropriate for a compact portable adapter that converts a host processor's logic-level serial interface into RS-232. The 3 V to 5.5 V operating range permits use with 3.3 V portable processors, and the 250 kbps rate supports configuration transfers, firmware downloads, and short diagnostic sessions. Its TSSOP construction is useful when connector placement and enclosure space are constrained. Maintain a controlled ground reference between the adapter and connected equipment, and consider whether an isolated interface is necessary when the two systems can have different ground potentials.
Disebarkan
Data logger and telemetry equipment
The MAX3243CPWRG4 can serve multiple telemetry paths in a data logger that collects status or command information from RS-232 sensors and embedded modules. Three receiver channels permit simultaneous monitoring of several slow-changing devices, while three driver channels support commands or acknowledgments. The 250 kbps limit is well suited to typical telemetry rates and leaves margin for protocol overhead and framing. For reliable field operation, terminate and route cables according to the RS-232 topology, use a low-impedance signal ground, and keep externally accessible line-side nets away from sensitive logic and clock traces.
Disebarkan
Point-of-sale terminal interface
The MAX3243CPWRG4 can interface a point-of-sale terminal or peripheral hub with equipment that retains legacy RS-232 communication. The three transmit and three receive channels permit multiple service, display, scanner, or controller connections on one logic board. Operation from 3 V to 5.5 V supports embedded processors and programmable controllers, while the surface-mount TSSOP package simplifies automated assembly. Use the manufacturer pin and application information to determine whether automatic shutdown or an always-active configuration is preferable, and protect connector-exposed pins with a circuit that is compatible with the system's ESD and surge requirements.
Disebarkan
Embedded test and measurement system
The MAX3243CPWRG4 is useful in an embedded test system that communicates with RS-232-controlled instruments, fixtures, or legacy service ports. Its 250 kbps capability supports instrument commands and status responses, while the multichannel arrangement reduces duplicated circuitry compared with single-channel transceivers. The 3 V to 5.5 V supply range enables integration with mixed-voltage processors and controllers. Engineers should place the transceiver close to the connector, include the recommended bypass capacitors, preserve RS-232 signal polarity, and verify that cable length and capacitance remain appropriate for the intended baud rate.
Disebarkan
Ringkasan Produk Disebarkan
Data referensi kejuruteraan untuk MAX3243CPWRG4 — perbandingan, panduan rancangan, dan maklumat kesediaan
Panduan Pilihan
Perbandingan dengan Gantian
| Parametr | Produk Ini | MAX3243CPW | MAX3243ECPWG4 | MAX3243CPA+ |
|---|---|---|---|---|
| Brand | Texas Instruments | Texas Instruments | Texas Instruments | Texas Instruments |
| Package | 28-pin TSSOP | 28-pin TSSOP | 28-pin TSSOP | 28-pin TSSOP |
| Product Type | Multichannel RS-232 line driver/receiver | Multichannel RS-232 line driver/receiver | Multichannel RS-232 line driver/receiver | Multichannel RS-232 line driver/receiver |
| Supply Voltage Range | 3 V to 5.5 V | 3 V to 5.5 V | 3 V to 5.5 V | 3 V to 5.5 V |
| Maximum Data Rate | 250 kbps | 250 kbps | 250 kbps | 250 kbps |
Penyeberangsung Jelas
- Combines six active RS-232 channels in one device (vsMC1489NG4)
- Supports both 3.3 V and 5 V system environments (vsMC1488NE4)
- Uses a compact 28-pin surface-mount package (vsMC3487DE4)
- Provides documented HBM ESD protection (vsMAX3243CPW)
Catatan Desain
Place the MAX3243CPWRG4 close to the RS-232 connector because the line-side nets carry bipolar voltage levels and are more susceptible to coupling than the logic-side signals. Keep the RS-232 traces away from clocks, reset lines, analog inputs, and sensitive digital buses. Route the connector ground as a signal-return path, and place external protection components directly beside the connector so surge current is diverted before reaching the transceiver pins.
Use the manufacturer's recommended bypass capacitance and connect it directly to the supply and ground pins with very short traces. The 3 V to 5.5 V operating range permits either 3.3 V or 5 V system rails, but the selected rail must remain within the datasheet's recommended limits. Confirm startup, enable or shutdown behavior, and supply-current requirements against the exact ordering variant before releasing the PCB layout.
Do not treat ±15 kV HBM protection as a complete external surge-protection strategy. Specify connector-level protection for the actual cable environment, maintain a common signal ground between communicating systems, and observe the transceiver's absolute-maximum ratings. Also avoid assuming that every MAX3243 suffix has identical shutdown behavior; the MAX3243E and MAX3243C families differ in control features even though their core RS-232 function and package family are related.
RS-232 is a single-ended bipolar interface, so receiver thresholds, driver slew behavior, cable capacitance, and grounding influence reliable communication at the 250 kbps device limit. Use the manufacturer's application circuit as the basis for external components and test the assembled interface with the longest intended cable. If higher data rates, longer cables, or electrically noisy industrial environments are expected, evaluate a lower-rate or differential communication standard instead.
Maklumat Kesediaan
The manufacturer datasheet and product page identify the device as commercial grade, but explicit RoHS, REACH, lead-free, halogen-free, conflict-minerals, and AEC-Q100 statements were not available in the verified text. The G4 ordering suffix indicates the manufacturer's green-compliant device configuration, but this is not treated as a substitute for explicit compliance statements.