INA253A2IPW - 80V Bidirectional Current Sense Amp | TI
MPN: INA253A2IPW ✓ ActiveINA253A2IPW Overview
A current-sense amplifier is an instrumentation amplifier that measures the small voltage generated across a shunt resistor and converts it into a proportional output voltage. The INA253 belongs to the current-sense amplifier hierarchy, where it bridges precision analog measurement and power-system monitoring. Integrating the shunt resistor reduces external component count and helps standardize the sensing element for bidirectional current applications.
Key electrical features include 350 kHz -3 dB bandwidth, 2.4 V/µs slew rate, 90 pA input bias current, and 1.8 mA supply current. The A2 gain version produces 200 mV/V output for each ampere of sensed current. Its wide -4 V to +80 V common-mode range allows the shunt path to operate at high bus voltages while the amplifier itself remains powered from a low-voltage supply.
Internally, the zero-drift architecture supports low offset behavior in precision measurement systems. The integrated precision shunt and chopper-stabilized amplifier are designed for systems where board space, component count, and current-direction measurement are important. Because the sensing element is integrated, PCB design should preserve the manufacturer-recommended current-path geometry and thermal conditions.
Typical applications include motor-drive phase current monitoring, industrial power-supply control, battery current measurement, solenoid current sensing, and LED driver feedback. The -4 V to +80 V common-mode capability is particularly useful in systems where a shunt can be placed in a high-voltage conductor while the INA253 remains connected to a 2.7 V to 5.5 V control supply.
Use the pin-description table in the manufacturer datasheet when assigning PCB tracks, especially for IN+, IN−, REF, OUT, and supply connections. Account for shunt heating at sustained high current and place input and reference components close to the device to minimize added error and pickup from fast-switching nodes.
This page organizes the electrical characteristics, application guidance, confirmed family alternatives, and design trade-offs of the INA253A2IPW. It helps engineers distinguish what the integrated 2 mΩ solution provides from lower-current sensing approaches and from gain variants in the same INA253 family.
Drop-in alternatives for INA253A2IPW — same package, pin-to-pin compatible. Different-package parts requiring PCB rework are excluded.
Variants in this series
Same-series models that are drop-in compatible with INA253A2IPW (same form factor and footprint) — differing in Common-Mode Voltage Range, Gain, Operating Temperature Range, Output Type, Product Type.
No drop-in alternatives available for this product.
Request AlternativesINA253A2IPW Maximum Ratings & Electrical Characteristics
| Product Type | Bidirectional zero-drift current-shunt monitor |
| Integrated Shunt Resistance | 2 mΩ |
| Gain | 200 mV/V |
| Supply Voltage Range | 2.7 V to 5.5 V |
| Common-Mode Voltage Range | -4 V to +80 V |
| Signal Bandwidth | 350 kHz at -3 dB |
| Slew Rate | 2.4 V/µs |
| Supply Current | 1.8 mA |
| Input Bias Current | 90 pA |
| Operating Temperature Range | -40 °C to +125 °C |
| Number of Circuits | 1 |
| Package | 20-pin TSSOP (PW) |
| Package Width | 4.40 mm |
| Mounting Type | Surface mount |
| Output Type | Voltage output |
| Current Direction | Bidirectional |
INA253A2IPW 4.40 mm Pin Configuration Guide
Pin configuration for INA253A2IPW (4.40 mm package). This analog component features input, output, and power supply pins. Refer to the manufacturer datasheet for offset null, compensation, and enable pin configurations. Ideal for signal conditioning and amplifier circuits.
No detailed pinout data available for INA253A2IPW.
Refer to the datasheet for full pin configuration.
Typical Applications
INA253A2IPW is suitable for 6 applications: Motor Phase Current Monitoring, Industrial Power-Supply Control, Battery Current Sensing, Solenoid and Relay Current Detection, LED Driver Feedback, High-Side Power-Path Monitoring.
Motor Phase Current Monitoring
The INA253A2IPW fits motor-controller phase sensing because its -4 V to +80 V common-mode range accommodates powered phase conductors while the amplifier operates from 2.7 V to 5.5 V. Place the integrated sensing path in series with the conductor and feed OUT to the controller ADC. The 200 mV/V gain produces 0.2 V per ampere, while the 350 kHz bandwidth captures switching transients. PWM rejection helps reduce unwanted disturbance, but the final input filter and isolation strategy must match the power stage.
Recommended
Industrial Power-Supply Control
For industrial power conversion, the INA253A2IPW can provide a compact current-feedback signal without an external shunt. Its integrated 2 mΩ element is suitable where the monitored conductor remains within the -4 V to +80 V common-mode range. The 200 mV/V scaling allows a controller or ADC to reconstruct current from the output voltage. Design the PCB current path for low resistance and sufficient copper area, and verify the shunt temperature rise at the maximum continuous load.
Recommended
Battery Current Sensing
The INA253A2IPW supports bidirectional battery current measurement when the battery bus remains inside its -4 V to +80 V common-mode range. The internal 2 mΩ shunt simplifies the sensing path, and the 200 mV/V gain provides a direct analog representation of charge or discharge current. At 10 A, the shunt dissipates an estimated 0.2 W, which makes conductor width, copper area, and thermal verification important. The output reference should be configured according to the manufacturer pin table.
Recommended
Solenoid and Relay Current Detection
The INA253A2IPW can detect current through a solenoid or relay winding when switching edges occur within the supported common-mode range. Its 2.4 V/µs slew rate and 350 kHz bandwidth permit the output to follow reasonably fast current events, while the integrated shunt avoids an external sensing element. Keep the high di/dt conductor away from REF and signal traces, use a stable reference implementation, and confirm that continuous dissipation and startup current remain below the device's absolute limits.
Recommended
LED Driver Feedback
The INA253A2IPW is suitable for current-regulated LED drivers when the high-side conductor falls within the -4 V to +80 V range. Its 200 mV/V gain allows the controller to compare a scaled current signal against a reference and adjust power delivery. Because the LED current may remain continuous, calculate shunt heating from I²R and maintain copper around the current path. The 1.8 mA supply current also helps preserve efficiency in low-power lighting systems.
Recommended
High-Side Power-Path Monitoring
The INA253A2IPW supports high-side monitoring because its common-mode input range extends to +80 V independently of the 2.7 V to 5.5 V amplifier supply. This separation enables measurement from a higher-voltage bus while the controller remains at a lower voltage. Route the high-current path with minimal resistance, keep sensitive reference connections compact, and use the manufacturer pin table to establish supply, output, and reference behavior. Confirm absolute maximum ratings for transients beyond the normal operating range.
Recommended
Recommended Products Summary
Engineering reference data for INA253A2IPW — comparison, design guidance, and compliance information.
Selection Guide
Comparison with Alternatives
| Parameter | This Product |
|---|---|
| Package | 20-pin TSSOP (PW) |
| Brand | Texas Instruments |
| Integrated Shunt Resistance | 2 mΩ |
| Gain | 200 mV/V |
| Supply Voltage Range | 2.7 V to 5.5 V |
| Common-Mode Voltage Range | -4 V to +80 V |
| Signal Bandwidth | 350 kHz at -3 dB |
| Slew Rate | 2.4 V/µs |
| Supply Current | 1.8 mA |
| Input Bias Current | 90 pA |
Key Differentiators
- Combines an integrated precision shunt and gain stage (vs Discrete shunt plus instrumentation-amplifier circuit)
- Wide common-mode range relative to its low supply voltage (vs INA253A1IPW)
- Balanced signal bandwidth and slew performance (vs INA253A3IPWR)
Design Notes
Estimated: using the integrated 2 mΩ shunt resistance, the shunt dissipation is I²R. At 20 A, the calculated loss is 0.8 W; at 10 A, it is 0.2 W. Use these values as initial thermal estimates, then verify the final rise with the actual PCB copper area, ambient temperature, and enclosure. Keep the high-current path short and wide, and avoid thermal coupling to precision reference components.
Assign IN+, IN−, supply, ground, REF, and OUT connections strictly from the manufacturer pin-description table. Place the shunt current path so its geometry provides the intended low resistance and thermal spreading. Keep REF components and output routing away from the switching-current conductor, use a compact ground return, and provide adequate copper around the TSSOP power and ground pins to limit parasitic resistance.
The 350 kHz -3 dB bandwidth makes the INA253A2IPW capable of responding to fast current edges, but excessive high-frequency energy can increase output ringing or reduce usable resolution. Route OUT directly toward the receiving ADC or comparator, minimize loop area, and place any input or reference filtering according to the manufacturer guidance. Validate filtering against the required response time because excessive capacitance or resistance can degrade control-loop behavior.
Do not treat the -4 V to +80 V common-mode rating as permission to exceed the absolute maximum ratings during faults. Verify surge, inductive kick, and supply-transient conditions at the circuit level. Also avoid assuming that another INA253 gain option is a drop-in substitute: changing from 200 mV/V to 100 mV/V or 400 mV/V changes ADC scaling, saturation margin, and firmware calibration.
Compliance Information
No specific RoHS, REACH, automotive-qualification, lead-free, halogen-free, or conflict-minerals statements appear in the cited product information. The INA253A2IPW is an industrial current-sense amplifier, so AEC-Q100 status is treated as not applicable.