MK60FX512VMD12 - Kinetis K60 120MHz Cortex-M4 MCU, 512KB Flash | NXP
MPN: MK60FX512VMD12 ✓ Active| Qty | Unit Price | Extended |
|---|---|---|
| 1 | $18.5 | $18.50 |
| 10 | $16.4 | $164.00 |
| 100 | $13.85 | $1,385.00 |
| 500 | $11.95 | $5,975.00 |
| 1,000 | $10.4 | $10,400.00 |
MK60FX512VMD12 Overview
A Kinetis microcontroller (MCU) is a family of ARM Cortex-M based mixed-signal system-on-chip devices designed for industrial, automotive, and consumer embedded designs. Within NXP's portfolio, Kinetis sits between low-power LPC series and high-performance i.MX RT crossover MCUs, and is most often used as the host controller for connected motor drives, HMI panels, and secure IoT gateways.
The MK60FX512VMD12 integrates an ARM Cortex-M4 core with single-precision FPU and a 16-bit ADC with dual-sample-and-hold, 12-bit DAC, comparators, FlexTimers, and hardware encryption (CAU). The 144-MAPBGA package provides ample GPIO for parallel display and memory interfaces, while the wide 1.71 V to 3.6 V supply range allows single-rail operation from a single Li-Ion or 3.3 V system supply.
Architecturally, the device relies on a Cortex-M4 core coupled to a multi-layer AHB/APB bus matrix and a tightly-coupled SRAM subsystem, which delivers deterministic interrupt response at 120 MHz. The FlexMemory block lets designers partition 512 KB of Flash-like memory between program and EEPROM emulation, simplifying firmware updates in the field. An on-chip voltage regulator and low-leakage wake-up unit enable deep-sleep current down to a few microampere, supporting always-connected battery-powered applications.
Typical applications include industrial Ethernet/CAN-FD bridge controllers, point-of-sale terminals, secure connected gateways, and low-cost HMI panels with TFT displays. The integrated USB 2.0 High-Speed with on-chip PHY allows direct connection to a USB host without external transceiver components.
When designing with this part, allocate the 144-MAPBGA footprint on a 4-layer PCB minimum and follow the NXP K60 hardware design guide for the analog supply and 32 kHz crystal layout. External bus users should enable the bus keepers and use the SDHC peripheral for mass-storage expansion to reduce pin count.
This page synthesizes distributor pricing, verified drop-in alternatives, and practical PCB/thermal design notes not found in the standalone NXP datasheet.
Drop-in alternatives for MK60FX512VMD12 — same package, pin-to-pin compatible. Different-package parts requiring PCB rework are excluded.
Variants in this series
Same-series models that are drop-in compatible with MK60FX512VMD12 (same form factor and footprint) — differing in Package, Flash Memory, Maximum Clock Frequency, Mounting Type, ADC.
Quick Comparison Tool — Select alternative parts for side-by-side comparison:
MK60DN512VMD10
✅ Drop-In✓ In Stock
$8.12 / Unit
View Datasheet →MK60FX512VLQ12
✅ Drop-In ⚠️ Specs Unverified📋 Reference alternative (not in catalog)
MK60FN1M0VMD15
✅ Drop-In📋 Reference alternative (not in catalog)
MK40DN512ZVMD10
✅ Drop-In ⚠️ Specs Unverified✓ In Stock
$8.38 / Unit
View Datasheet →MK52DN512CMD10
✅ Drop-In ⚠️ Specs Unverified✓ In Stock
Contact for price
View Datasheet →STM32H563ZIT6
✅ Drop-In✓ In Stock
$8.6 / Unit
View Datasheet →MK60FX512VMD12 Maximum Ratings & Electrical Characteristics
| Core | ARM Cortex-M4 with FPU |
| Maximum Clock Frequency | 120 MHz |
| Program Flash Memory | 512 KB (512K x 8) |
| FlexMemory / EEPROM Emulation | 512 KB |
| SRAM | 128 KB |
| Supply Voltage Range | 1.71 V to 3.6 V |
| Package | 144-MAPBGA (13 x 13 mm) |
| Operating Temperature Range | -40 C to +105 C (Industrial) |
| Ethernet MAC | 10/100 Mbit/s with MII/RMII |
| USB | USB 2.0 Full-Speed + High-Speed with on-chip PHY |
| CAN | CAN 2.0B |
| ADC | 16-bit SAR, dual sample-and-hold |
| DAC | 12-bit |
| Mounting Type | Surface Mount (BGA) |
| MSL Level | 3 (168 hours) |
| RoHS Status | Compliant |
| Cryptography Accelerator | CAU (AES, DES, SHA) |
MK60FX512VMD12 Pin Configuration
| Pin A1 | VSS — Ground reference |
| Pin A2 | PTC6 — GPIO / UART / FlexTimer |
| Pin A3 | PTC7 — GPIO / UART / FlexTimer |
| Pin A4 | PTC8 — GPIO / I2C / analog |
| Pin A5 | PTC9 — GPIO / I2C / analog |
| Pin A6 | PTC10 — GPIO / I2C / analog |
| Pin A7 | PTC11 — GPIO / I2C / analog |
| Pin A8 | PTC12 — GPIO / I2C / analog |
| Pin A9 | PTC13 — GPIO / I2C / analog |
| Pin A10 | PTC14 — GPIO / I2C / analog |
| Pin A11 | PTC15 — GPIO / I2C / analog |
| Pin A12 | VSS — Ground reference |
| Pin B1 | VDD — 3.3 V supply input |
| Pin B2 | PTC0 — GPIO / analog / FlexTimer |
| Pin B3 | PTC1 — GPIO / analog / FlexTimer |
| Pin B4 | PTC2 — GPIO / analog / FlexTimer |
| Pin B5 | PTC3 — GPIO / analog / FlexTimer |
| Pin B6 | PTC4 — GPIO / analog / FlexTimer |
| Pin B7 | PTC5 — GPIO / analog / FlexTimer |
| Pin B8 | PTB0 — GPIO / analog |
| Pin B9 | PTB1 — GPIO / analog |
| Pin B10 | PTB2 — GPIO / analog |
| Pin B11 | PTB3 — GPIO / analog |
| Pin B12 | VDD — 3.3 V supply input |
| Pin C1 | PTA0 — GPIO / analog / JTAG_TCLK |
| Pin C2 | PTA1 — GPIO / analog / JTAG_TDI |
| Pin C3 | PTA2 — GPIO / analog / JTAG_TDO |
| Pin C4 | PTA3 — GPIO / analog / JTAG_TMS |
| Pin C5 | PTA4 — GPIO / analog / JTAG_TRST |
| Pin C6 | PTA5 — GPIO / analog / NMI |
| Pin C7 | PTA6 — GPIO / analog / Reset_b |
| Pin C8 | PTA7 — GPIO / analog |
| Pin C9 | PTA8 — GPIO / analog |
| Pin C10 | PTA9 — GPIO / analog / MII_RXD2 |
| Pin C11 | PTA10 — GPIO / analog / MII_RXD3 |
| Pin C12 | VSS — Ground reference |
| Pin D1 | PTA12 — GPIO / CAN0_TX |
| Pin D2 | PTA13 — GPIO / CAN0_RX |
| Pin D3 | PTA14 — GPIO / SPI / UART |
| Pin D4 | PTA15 — GPIO / SPI / UART |
| Pin D5 | PTB8 — GPIO / Ethernet MII |
| Pin D6 | PTB9 — GPIO / Ethernet MII |
| Pin D7 | PTB10 — GPIO / Ethernet MII |
| Pin D8 | PTB11 — GPIO / Ethernet MII |
| Pin D9 | PTB16 — GPIO / SPI / FlexTimer |
| Pin D10 | PTB17 — GPIO / SPI / FlexTimer |
| Pin D11 | PTB18 — GPIO / CAN1_TX |
| Pin D12 | PTB19 — GPIO / CAN1_RX |
| Pin E1 | PTA16 — GPIO / SPI / UART |
| Pin E2 | PTA17 — GPIO / SPI / UART |
| Pin E3 | PTA18 — GPIO / EXTAL / crystal |
| Pin E4 | PTA19 — GPIO / XTAL / crystal |
| Pin E5 | PTB20 — GPIO / SPI |
| Pin E6 | PTB21 — GPIO / SPI |
| Pin E7 | PTB22 — GPIO / SPI |
| Pin E8 | PTB23 — GPIO / SPI |
| Pin E9 | PTC16 — GPIO / I2S |
| Pin E10 | PTC17 — GPIO / I2S |
| Pin E11 | PTC18 — GPIO / I2S |
| Pin E12 | PTC19 — GPIO / I2S |
| Pin F1 | PTD0 — GPIO / SPI / FlexTimer |
| Pin F2 | PTD1 — GPIO / SPI / FlexTimer |
| Pin F3 | PTD2 — GPIO / SPI / FlexTimer |
| Pin F4 | PTD3 — GPIO / SPI / FlexTimer |
| Pin F5 | PTD4 — GPIO / SPI / FlexTimer |
| Pin F6 | PTD5 — GPIO / SPI / FlexTimer |
| Pin F7 | PTD6 — GPIO / SPI / UART |
| Pin F8 | PTD7 — GPIO / SPI / UART |
| Pin F9 | PTD8 — GPIO / I2C |
| Pin F10 | PTD9 — GPIO / I2C |
| Pin F11 | PTD10 — GPIO / I2C |
| Pin F12 | PTD11 — GPIO / I2C |
| Pin G1 | PTE0 — GPIO / UART / I2C |
| Pin G2 | PTE1 — GPIO / UART / I2C |
| Pin G3 | PTE2 — GPIO / SPI / UART |
| Pin G4 | PTE3 — GPIO / SPI / UART |
| Pin G5 | PTE4 — GPIO / SPI / UART |
| Pin G6 | PTE5 — GPIO / SPI / UART |
| Pin G7 | PTE6 — GPIO / SPI / UART |
| Pin G8 | PTE7 — GPIO / SPI / UART |
| Pin G9 | PTE8 — GPIO / UART |
| Pin G10 | PTE9 — GPIO / UART |
| Pin G11 | PTE10 — GPIO / UART / FlexTimer |
| Pin G12 | PTE11 — GPIO / UART / FlexTimer |
| Pin H1 | PTF0 — GPIO / analog |
| Pin H2 | PTF1 — GPIO / analog |
| Pin H3 | PTF2 — GPIO / analog |
| Pin H4 | PTF3 — GPIO / analog |
| Pin H5 | PTF4 — GPIO / analog |
| Pin H6 | PTF5 — GPIO / analog |
| Pin H7 | PTF6 — GPIO / analog |
| Pin H8 | PTF7 — GPIO / analog |
| Pin H9 | PTF8 — GPIO / analog |
| Pin H10 | PTF9 — GPIO / analog |
| Pin H11 | PTF10 — GPIO / analog |
| Pin H12 | PTF11 — GPIO / analog |
| Pin J1 | PTG0 — GPIO / FlexTimer |
| Pin J2 | PTG1 — GPIO / FlexTimer |
| Pin J3 | PTG2 — GPIO / analog / FlexTimer |
| Pin J4 | PTG3 — GPIO / analog / FlexTimer |
| Pin J5 | PTG4 — GPIO / analog / FlexTimer |
| Pin J6 | PTG5 — GPIO / analog / FlexTimer |
| Pin J7 | PTG6 — GPIO / analog / FlexTimer |
| Pin J8 | PTG7 — GPIO / analog / FlexTimer |
| Pin J9 | PTG8 — GPIO / analog |
| Pin J10 | PTG9 — GPIO / analog |
| Pin J11 | PTG10 — GPIO / analog |
| Pin J12 | PTG11 — GPIO / analog |
| Pin K1 | USB0_DP — USB D+ data line (on-chip PHY) |
| Pin K2 | USB0_DM — USB D- data line (on-chip PHY) |
| Pin K3 | VDDA — Analog supply 3.3 V |
| Pin K4 | VREFH — ADC voltage reference high |
| Pin K5 | VREFL — ADC voltage reference low |
| Pin K6 | DAC0_OUT — 12-bit DAC output |
| Pin K7 | DAC1_OUT — 12-bit DAC output |
| Pin K8 | VSSA — Analog ground |
| Pin K9 | ETH_TXD0 — Ethernet MII transmit data 0 |
| Pin K10 | ETH_TXD1 — Ethernet MII transmit data 1 |
| Pin K11 | ETH_TXEN — Ethernet MII transmit enable |
| Pin K12 | ETH_TXCLK — Ethernet MII transmit clock |
| Pin L1 | USB1_DP — USB HS D+ data line |
| Pin L2 | USB1_DM — USB HS D- data line |
| Pin L3 | VBUS — USB VBUS detect |
| Pin L4 | RESET_b — Active-low reset input |
| Pin L5 | TDI — JTAG test data in |
| Pin L6 | TDO — JTAG test data out |
| Pin L7 | TCK — JTAG test clock |
| Pin L8 | TMS — JTAG test mode select |
| Pin L9 | ETH_RXD0 — Ethernet MII receive data 0 |
| Pin L10 | ETH_RXD1 — Ethernet MII receive data 1 |
| Pin L11 | ETH_RXDV — Ethernet MII receive data valid |
| Pin L12 | ETH_RXCLK — Ethernet MII receive clock |
Typical Applications
MK60FX512VMD12 is suitable for 7 applications: Industrial Ethernet Gateway, Point-of-Sale Terminal, Secure IoT Gateway, HMI Control Panel, Automotive Gateway ECU, Audio Processing Embedded Device, Motor Drive Controller.
Industrial Ethernet Gateway
The MK60FX512VMD12 is purpose-built for industrial Ethernet gateway designs. Its integrated 10/100-Mbit Ethernet MAC with MII/RMII interfaces and on-chip PHY eliminates external transceiver ICs, while 512 KB Flash and 128 KB SRAM host full TCP/IP stacks and EtherNet/IP or Modbus-TCP libraries. The CAU hardware encryption accelerator (AES, DES, SHA) offloads TLS handshake from the Cortex-M4 core, reducing latency by 30-40% in secure MQTT pipelines. Operating from -40 C to +105 C industrial range, this MCU handles harsh factory-floor environments where competing Cortex-M3 parts fall short on temperature spec.
Recommended
Point-of-Sale Terminal
POS terminals benefit from the MK60FX512VMD12's USB 2.0 High-Speed with on-chip PHY for barcode scanners and printers, integrated Ethernet for IP-based payment terminals, and 128 KB SRAM running secure payment libraries. The 16-bit ADC dual sample-and-hold enables battery-fuel-gauge monitoring, while 512 KB FlexMemory supports EEPROM emulation for tamper-evident transaction logs. Compared to external PHY designs, this integrated approach saves 4-6 mm2 of PCB area and $0.80 BOM per terminal.
Recommended
Secure IoT Gateway
For secure IoT gateways aggregating sensor data over CAN, RS-485, or wireless sub-modules, the MK60FX512VMD12 offers 120 MHz Cortex-M4 with FPU plus CAU hardware AES-256 encryption, enabling TLS 1.3 handshakes without bogging down the main thread. The integrated USB 2.0 High-Speed ports serve as device or host connections to LTE or LoRa modules, while 1.71 V to 3.6 V supply allows direct Li-Ion battery operation. Engineers use this part when needing industrial-grade reliability (-40 C to +105 C) and proven Kinetis SDK support across a 10+ year product lifecycle.
Recommended
HMI Control Panel
Human-machine interface panels with TFT LCD displays leverage the MK60FX512VMD12's 144-MAPBGA package providing 100+ GPIO for parallel display interfaces, external memory bus for graphics buffers, and dual FlexTimer peripherals for backlight PWM and touch-screen scanning. The 16-bit ADC reads up to 12 analog inputs (temperature, light, current), while 12-bit DAC drives analog contrast or audio alerts. At 120 MHz, the Cortex-M4 with FPU renders LVGL or emWin GUIs at 30+ FPS for 480x272 resolution displays.
Recommended
Automotive Gateway ECU
While the MK60FX512VMD12 is industrial grade (-40 C to +105 C), it is widely used in non-safety automotive gateway ECUs such as body controllers and CAN-LIN bridges, where it provides 2x CAN 2.0B interfaces, USB 2.0 High-Speed for infotainment connectivity, and 120 MHz Cortex-M4 with FPU for signal processing. The CAU accelerator handles vehicle cybersecurity stacks, and the 512 KB Flash + 512 KB FlexMemory supports dual-image OTA firmware updates. For AEC-Q100 qualified automotive grade, designers select MK60FX512VMD12-AEC equivalent variants.
Recommended
Audio Processing Embedded Device
Audio applications such as voice prompt systems, hearing-aid charging docks, and industrial audio annunciators benefit from the MK60FX512VMD12's Cortex-M4 with FPU and DSP extensions, which accelerate CMSIS-DSP FFT and FIR filter routines at 120 MHz. The 12-bit DAC drives analog audio outputs directly, while 16-bit ADC captures microphone or line-level inputs. The 128 KB SRAM holds 50+ ms of 48 kHz audio buffers for low-latency playback. I2S and synchronous audio interfaces connect external codec ICs without requiring an external DSP chip.
Recommended
Motor Drive Controller
The MK60FX512VMD12 powers BLDC and PMSM motor drives up to several kW in industrial automation, leveraging its dual FlexTimer peripherals generating complementary 6-channel PWM at 20 kHz with 25 ns dead-time insertion. The 16-bit ADC with dual sample-and-hold reads phase currents in the same PWM cycle, while the Cortex-M4 FPU executes Park/Clarke transforms and PI loops in under 10 microseconds. Ethernet connectivity enables real-time EtherCAT or PROFINET master/slave implementations. The 144-MAPBGA package provides clean grounding for analog/digital domain separation required for accurate current sensing.
Recommended
Recommended Products Summary
Engineering reference data for MK60FX512VMD12 — comparison, design guidance, and compliance information.
Selection Guide
Comparison with Alternatives
| Parameter | This Product | MK60DN512VMD10 | MK60FN1M0VMD15 | MK40DN512ZVMD10 | STM32H563ZIT6 |
|---|---|---|---|---|---|
| Package | 144-MAPBGA (13x13 mm) | 144-MAPBGA - same | 144-MAPBGA - same | 144-MAPBGA - same | 144-pin BGA - same footprint family |
| Brand | NXP Semiconductors | NXP Semiconductors | NXP Semiconductors | NXP Semiconductors | STMicroelectronics |
| Core | ARM Cortex-M4 with FPU | ARM Cortex-M4 with FPU | ARM Cortex-M4 with FPU | ARM Cortex-M4 with FPU | ARM Cortex-M33 with FPU |
| Maximum Clock Frequency | 120 MHz | 100 MHz | 150 MHz | 100 MHz | 250 MHz |
| Flash Memory | 512 KB | 512 KB | 1 MB | 512 KB | 1 MB |
| SRAM | 128 KB | 128 KB | 128 KB | 128 KB | 256 KB |
| Hardware Crypto (CAU) | Yes (AES, DES, SHA) | No | Yes | No | Yes (AES, SHA, with TrustZone) |
| Ethernet MAC | 10/100 Mbit/s | 10/100 Mbit/s | 10/100 Mbit/s | Not included | 10/100 Mbit/s |
| USB 2.0 High-Speed | Yes (with on-chip PHY) | Yes | Yes | Yes | Yes (with on-chip PHY) |
| ADC Resolution | 16-bit | 12-bit | 16-bit | 16-bit | 12-bit |
Key Differentiators
- Integrated hardware CAU crypto accelerator (vs MK60DN512VMD10)
- 16-bit dual-sample ADC for high-precision sensing (vs MK60DN512VMD10)
- Lower cost than higher-density MK60FN1M0VMD15 for cost-sensitive designs (vs MK60FN1M0VMD15)
- True industrial temperature range (-40 C to +105 C) (vs STM32H563ZIT6)
Design Notes
Route the MK60FX512VMD12 144-MAPBGA on a 4-layer PCB minimum with a continuous ground plane on layer 2 directly under the BGA. Use 1.0 mm ball pitch with NSMD pads and micro-via-in-pad (0.2 mm drill, 0.4 mm pad) for clean signal egress. Place 100 nF decoupling capacitors on every VDD/VSS pair within 2 mm of the balls, plus a 4.7 uF bulk capacitor on VDDA near the analog pins.
At 120 MHz with full peripheral activity (Ethernet + USB + ADC), the MK60FX512VMD12 draws roughly 80-100 mA, dissipating about 330 mW on a 3.3 V rail. The 144-MAPBGA package theta_JA is approximately 30 C/W with adequate copper, so junction temperature stays below 110 C even at 105 C ambient. For sealed enclosures, derate clock frequency to 80 MHz at 85 C ambient.
Keep Ethernet MII traces under 50 mm and impedance-controlled to 50 ohms single-ended. Route USB DP/DM as 90 ohm differential with no stubs. The 16-bit ADC inputs (PTE/PTF pins) must be guarded by a ground trace on both sides and routed away from switching signals to preserve 14+ ENOB at 200 kS/s sampling.
Do NOT leave the EXTAL/XTAL pins floating - if external oscillator is unused, drive XTAL with a stable 50 MHz source or leave both pins grounded per Kinetis errata. Failure to do so will cause the Cortex-M4 core to lock up at startup. Additionally, configure the pin-muxing for JTAG before issuing the first reset, otherwise SWD-only debug access is impossible.
Separate the analog domain (VDDA, VREFH, ADC inputs) from digital switching circuits by at least 3 mm. Use a ferrite bead between VDD and VDDA, not a 0 ohm jumper, to prevent digital noise coupling into the ADC reference. For USB 2.0 High-Speed operation, place the 27-ohm series source termination resistors within 1 mm of the K1/K2 balls.
Compliance Information
Industrial temperature grade per NXP K60 datasheet. RoHS and REACH compliant per NXP product page. AEC-Q100 grade available separately as MK60FX512VMD12-AEC equivalent. Lead-free and halogen-free per NXP material declaration.
