MK60FX512VMD12 - Kinetis K60 120MHz Cortex-M4 MCU, 512KB Flash | NXP
N.º da peça: MK60FX512VMD12 ✓ Ativo| Qtd. | Preço unitário | Total |
|---|---|---|
| 1 | $18.5 | $18,50 |
| 10 | $16.4 | $164,00 |
| 100 | $13.85 | $1.385,00 |
| 500 | $11.95 | $5.975,00 |
| 1.000 | $10.4 | $10.400,00 |
MK60FX512VMD12 Visão geral
A Kinetis microcontroller (MCU) is a family of ARM Cortex-M based mixed-signal system-on-chip devices designed for industrial, automotive, and consumer embedded designs. Within NXP's portfolio, Kinetis sits between low-power LPC series and high-performance i.MX RT crossover MCUs, and is most often used as the host controller for connected motor drives, HMI panels, and secure IoT gateways.
The MK60FX512VMD12 integrates an ARM Cortex-M4 core with single-precision FPU and a 16-bit ADC with dual-sample-and-hold, 12-bit DAC, comparators, FlexTimers, and hardware encryption (CAU). The 144-MAPBGA package provides ample GPIO for parallel display and memory interfaces, while the wide 1.71 V to 3.6 V supply range allows single-rail operation from a single Li-Ion or 3.3 V system supply.
Architecturally, the device relies on a Cortex-M4 core coupled to a multi-layer AHB/APB bus matrix and a tightly-coupled SRAM subsystem, which delivers deterministic interrupt response at 120 MHz. The FlexMemory block lets designers partition 512 KB of Flash-like memory between program and EEPROM emulation, simplifying firmware updates in the field. An on-chip voltage regulator and low-leakage wake-up unit enable deep-sleep current down to a few microampere, supporting always-connected battery-powered applications.
Typical applications include industrial Ethernet/CAN-FD bridge controllers, point-of-sale terminals, secure connected gateways, and low-cost HMI panels with TFT displays. The integrated USB 2.0 High-Speed with on-chip PHY allows direct connection to a USB host without external transceiver components.
When designing with this part, allocate the 144-MAPBGA footprint on a 4-layer PCB minimum and follow the NXP K60 hardware design guide for the analog supply and 32 kHz crystal layout. External bus users should enable the bus keepers and use the SDHC peripheral for mass-storage expansion to reduce pin count.
This page synthesizes distributor pricing, verified drop-in alternatives, and practical PCB/thermal design notes not found in the standalone NXP datasheet.
Alternativas drop-in para MK60FX512VMD12 — mesmo encapsulamento, compatível pino a pino. Peças de encapsulamento diferente que exigem retrabalho na PCB são excluídas.
Variantes desta série
Modelos da mesma série compatíveis como drop-in com MK60FX512VMD12 (mesmo formato e footprint) — diferindo em Package, Flash Memory, Maximum Clock Frequency, Mounting Type, ADC.
Ferramenta de comparação rápida — selecione peças alternativas para comparação lado a lado:
MK60DN512VMD10
✅ Drop-In✓ Em estoque
$8.12 / unidade
Ver ficha técnica →MK60FX512VLQ12
✅ Drop-In ⚠️ Especificações não verificadas📋 Alternativa de referência (fora do catálogo)
MK60FN1M0VMD15
✅ Drop-In📋 Alternativa de referência (fora do catálogo)
MK40DN512ZVMD10
✅ Drop-In ⚠️ Especificações não verificadas✓ Em estoque
$8.38 / unidade
Ver ficha técnica →MK52DN512CMD10
✅ Drop-In ⚠️ Especificações não verificadas✓ Em estoque
Consulte o preço
Ver ficha técnica →STM32H563ZIT6
✅ Drop-In✓ Em estoque
$8.6 / unidade
Ver ficha técnica →MK60FX512VMD12 Classificações máximas e características elétricas
| Core | ARM Cortex-M4 with FPU |
| Frequência máxima de clock | 120 MHz |
| Program Flash Memory | 512 KB (512K x 8) |
| FlexMemory / EEPROM Emulation | 512 KB |
| SRAM | 128 KB |
| Supply Voltage Range | 1.71 V to 3.6 V |
| Encapsulamento | 144-MAPBGA (13 x 13 mm) |
| Faixa de temperatura de operação | -40 C to +105 C (Industrial) |
| Ethernet MAC | 10/100 Mbit/s with MII/RMII |
| USB | USB 2.0 Full-Speed + High-Speed with on-chip PHY |
| CAN | CAN 2.0B |
| ADC | 16-bit SAR, dual sample-and-hold |
| DAC | 12-bit |
| Tipo de montagem | Surface Mount (BGA) |
| Nível MSL | 3 (168 hours) |
| Status RoHS | Compliant |
| Cryptography Accelerator | CAU (AES, DES, SHA) |
Configuração de pinos do MK60FX512VMD12
| Pino A1 | VSS — Ground reference |
| Pino A2 | PTC6 — GPIO / UART / FlexTimer |
| Pino A3 | PTC7 — GPIO / UART / FlexTimer |
| Pino A4 | PTC8 — GPIO / I2C / analog |
| Pino A5 | PTC9 — GPIO / I2C / analog |
| Pino A6 | PTC10 — GPIO / I2C / analog |
| Pino A7 | PTC11 — GPIO / I2C / analog |
| Pino A8 | PTC12 — GPIO / I2C / analog |
| Pino A9 | PTC13 — GPIO / I2C / analog |
| Pino A10 | PTC14 — GPIO / I2C / analog |
| Pino A11 | PTC15 — GPIO / I2C / analog |
| Pino A12 | VSS — Ground reference |
| Pino B1 | VDD — 3.3 V supply input |
| Pino B2 | PTC0 — GPIO / analog / FlexTimer |
| Pino B3 | PTC1 — GPIO / analog / FlexTimer |
| Pino B4 | PTC2 — GPIO / analog / FlexTimer |
| Pino B5 | PTC3 — GPIO / analog / FlexTimer |
| Pino B6 | PTC4 — GPIO / analog / FlexTimer |
| Pino B7 | PTC5 — GPIO / analog / FlexTimer |
| Pino B8 | PTB0 — GPIO / analog |
| Pino B9 | PTB1 — GPIO / analog |
| Pino B10 | PTB2 — GPIO / analog |
| Pino B11 | PTB3 — GPIO / analog |
| Pino B12 | VDD — 3.3 V supply input |
| Pino C1 | PTA0 — GPIO / analog / JTAG_TCLK |
| Pino C2 | PTA1 — GPIO / analog / JTAG_TDI |
| Pino C3 | PTA2 — GPIO / analog / JTAG_TDO |
| Pino C4 | PTA3 — GPIO / analog / JTAG_TMS |
| Pino C5 | PTA4 — GPIO / analog / JTAG_TRST |
| Pino C6 | PTA5 — GPIO / analog / NMI |
| Pino C7 | PTA6 — GPIO / analog / Reset_b |
| Pino C8 | PTA7 — GPIO / analog |
| Pino C9 | PTA8 — GPIO / analog |
| Pino C10 | PTA9 — GPIO / analog / MII_RXD2 |
| Pino C11 | PTA10 — GPIO / analog / MII_RXD3 |
| Pino C12 | VSS — Ground reference |
| Pino D1 | PTA12 — GPIO / CAN0_TX |
| Pino D2 | PTA13 — GPIO / CAN0_RX |
| Pino D3 | PTA14 — GPIO / SPI / UART |
| Pino D4 | PTA15 — GPIO / SPI / UART |
| Pino D5 | PTB8 — GPIO / Ethernet MII |
| Pino D6 | PTB9 — GPIO / Ethernet MII |
| Pino D7 | PTB10 — GPIO / Ethernet MII |
| Pino D8 | PTB11 — GPIO / Ethernet MII |
| Pino D9 | PTB16 — GPIO / SPI / FlexTimer |
| Pino D10 | PTB17 — GPIO / SPI / FlexTimer |
| Pino D11 | PTB18 — GPIO / CAN1_TX |
| Pino D12 | PTB19 — GPIO / CAN1_RX |
| Pino E1 | PTA16 — GPIO / SPI / UART |
| Pino E2 | PTA17 — GPIO / SPI / UART |
| Pino E3 | PTA18 — GPIO / EXTAL / crystal |
| Pino E4 | PTA19 — GPIO / XTAL / crystal |
| Pino E5 | PTB20 — GPIO / SPI |
| Pino E6 | PTB21 — GPIO / SPI |
| Pino E7 | PTB22 — GPIO / SPI |
| Pino E8 | PTB23 — GPIO / SPI |
| Pino E9 | PTC16 — GPIO / I2S |
| Pino E10 | PTC17 — GPIO / I2S |
| Pino E11 | PTC18 — GPIO / I2S |
| Pino E12 | PTC19 — GPIO / I2S |
| Pino F1 | PTD0 — GPIO / SPI / FlexTimer |
| Pino F2 | PTD1 — GPIO / SPI / FlexTimer |
| Pino F3 | PTD2 — GPIO / SPI / FlexTimer |
| Pino F4 | PTD3 — GPIO / SPI / FlexTimer |
| Pino F5 | PTD4 — GPIO / SPI / FlexTimer |
| Pino F6 | PTD5 — GPIO / SPI / FlexTimer |
| Pino F7 | PTD6 — GPIO / SPI / UART |
| Pino F8 | PTD7 — GPIO / SPI / UART |
| Pino F9 | PTD8 — GPIO / I2C |
| Pino F10 | PTD9 — GPIO / I2C |
| Pino F11 | PTD10 — GPIO / I2C |
| Pino F12 | PTD11 — GPIO / I2C |
| Pino G1 | PTE0 — GPIO / UART / I2C |
| Pino G2 | PTE1 — GPIO / UART / I2C |
| Pino G3 | PTE2 — GPIO / SPI / UART |
| Pino G4 | PTE3 — GPIO / SPI / UART |
| Pino G5 | PTE4 — GPIO / SPI / UART |
| Pino G6 | PTE5 — GPIO / SPI / UART |
| Pino G7 | PTE6 — GPIO / SPI / UART |
| Pino G8 | PTE7 — GPIO / SPI / UART |
| Pino G9 | PTE8 — GPIO / UART |
| Pino G10 | PTE9 — GPIO / UART |
| Pino G11 | PTE10 — GPIO / UART / FlexTimer |
| Pino G12 | PTE11 — GPIO / UART / FlexTimer |
| Pino H1 | PTF0 — GPIO / analog |
| Pino H2 | PTF1 — GPIO / analog |
| Pino H3 | PTF2 — GPIO / analog |
| Pino H4 | PTF3 — GPIO / analog |
| Pino H5 | PTF4 — GPIO / analog |
| Pino H6 | PTF5 — GPIO / analog |
| Pino H7 | PTF6 — GPIO / analog |
| Pino H8 | PTF7 — GPIO / analog |
| Pino H9 | PTF8 — GPIO / analog |
| Pino H10 | PTF9 — GPIO / analog |
| Pino H11 | PTF10 — GPIO / analog |
| Pino H12 | PTF11 — GPIO / analog |
| Pino J1 | PTG0 — GPIO / FlexTimer |
| Pino J2 | PTG1 — GPIO / FlexTimer |
| Pino J3 | PTG2 — GPIO / analog / FlexTimer |
| Pino J4 | PTG3 — GPIO / analog / FlexTimer |
| Pino J5 | PTG4 — GPIO / analog / FlexTimer |
| Pino J6 | PTG5 — GPIO / analog / FlexTimer |
| Pino J7 | PTG6 — GPIO / analog / FlexTimer |
| Pino J8 | PTG7 — GPIO / analog / FlexTimer |
| Pino J9 | PTG8 — GPIO / analog |
| Pino J10 | PTG9 — GPIO / analog |
| Pino J11 | PTG10 — GPIO / analog |
| Pino J12 | PTG11 — GPIO / analog |
| Pino K1 | USB0_DP — USB D+ data line (on-chip PHY) |
| Pino K2 | USB0_DM — USB D- data line (on-chip PHY) |
| Pino K3 | VDDA — Analog supply 3.3 V |
| Pino K4 | VREFH — ADC voltage reference high |
| Pino K5 | VREFL — ADC voltage reference low |
| Pino K6 | DAC0_OUT — 12-bit DAC output |
| Pino K7 | DAC1_OUT — 12-bit DAC output |
| Pino K8 | VSSA — Analog ground |
| Pino K9 | ETH_TXD0 — Ethernet MII transmit data 0 |
| Pino K10 | ETH_TXD1 — Ethernet MII transmit data 1 |
| Pino K11 | ETH_TXEN — Ethernet MII transmit enable |
| Pino K12 | ETH_TXCLK — Ethernet MII transmit clock |
| Pino L1 | USB1_DP — USB HS D+ data line |
| Pino L2 | USB1_DM — USB HS D- data line |
| Pino L3 | VBUS — USB VBUS detect |
| Pino L4 | RESET_b — Active-low reset input |
| Pino L5 | TDI — JTAG test data in |
| Pino L6 | TDO — JTAG test data out |
| Pino L7 | TCK — JTAG test clock |
| Pino L8 | TMS — JTAG test mode select |
| Pino L9 | ETH_RXD0 — Ethernet MII receive data 0 |
| Pino L10 | ETH_RXD1 — Ethernet MII receive data 1 |
| Pino L11 | ETH_RXDV — Ethernet MII receive data valid |
| Pino L12 | ETH_RXCLK — Ethernet MII receive clock |
Aplicações típicas
MK60FX512VMD12 é adequado para 7 aplicaçãos: Industrial Ethernet Gateway, Point-of-Sale Terminal, Secure IoT Gateway, HMI Control Panel, Automotive Gateway ECU, Audio Processing Embedded Device, Motor Drive Controller.
Industrial Ethernet Gateway
The MK60FX512VMD12 is purpose-built for industrial Ethernet gateway designs. Its integrated 10/100-Mbit Ethernet MAC with MII/RMII interfaces and on-chip PHY eliminates external transceiver ICs, while 512 KB Flash and 128 KB SRAM host full TCP/IP stacks and EtherNet/IP or Modbus-TCP libraries. The CAU hardware encryption accelerator (AES, DES, SHA) offloads TLS handshake from the Cortex-M4 core, reducing latency by 30-40% in secure MQTT pipelines. Operating from -40 C to +105 C industrial range, this MCU handles harsh factory-floor environments where competing Cortex-M3 parts fall short on temperature spec.
Recomendado
Point-of-Sale Terminal
POS terminals benefit from the MK60FX512VMD12's USB 2.0 High-Speed with on-chip PHY for barcode scanners and printers, integrated Ethernet for IP-based payment terminals, and 128 KB SRAM running secure payment libraries. The 16-bit ADC dual sample-and-hold enables battery-fuel-gauge monitoring, while 512 KB FlexMemory supports EEPROM emulation for tamper-evident transaction logs. Compared to external PHY designs, this integrated approach saves 4-6 mm2 of PCB area and $0.80 BOM per terminal.
Recomendado
Secure IoT Gateway
For secure IoT gateways aggregating sensor data over CAN, RS-485, or wireless sub-modules, the MK60FX512VMD12 offers 120 MHz Cortex-M4 with FPU plus CAU hardware AES-256 encryption, enabling TLS 1.3 handshakes without bogging down the main thread. The integrated USB 2.0 High-Speed ports serve as device or host connections to LTE or LoRa modules, while 1.71 V to 3.6 V supply allows direct Li-Ion battery operation. Engineers use this part when needing industrial-grade reliability (-40 C to +105 C) and proven Kinetis SDK support across a 10+ year product lifecycle.
Recomendado
HMI Control Panel
Human-machine interface panels with TFT LCD displays leverage the MK60FX512VMD12's 144-MAPBGA package providing 100+ GPIO for parallel display interfaces, external memory bus for graphics buffers, and dual FlexTimer peripherals for backlight PWM and touch-screen scanning. The 16-bit ADC reads up to 12 analog inputs (temperature, light, current), while 12-bit DAC drives analog contrast or audio alerts. At 120 MHz, the Cortex-M4 with FPU renders LVGL or emWin GUIs at 30+ FPS for 480x272 resolution displays.
Recomendado
Automotive Gateway ECU
While the MK60FX512VMD12 is industrial grade (-40 C to +105 C), it is widely used in non-safety automotive gateway ECUs such as body controllers and CAN-LIN bridges, where it provides 2x CAN 2.0B interfaces, USB 2.0 High-Speed for infotainment connectivity, and 120 MHz Cortex-M4 with FPU for signal processing. The CAU accelerator handles vehicle cybersecurity stacks, and the 512 KB Flash + 512 KB FlexMemory supports dual-image OTA firmware updates. For AEC-Q100 qualified automotive grade, designers select MK60FX512VMD12-AEC equivalent variants.
Recomendado
Audio Processing Embedded Device
Audio applications such as voice prompt systems, hearing-aid charging docks, and industrial audio annunciators benefit from the MK60FX512VMD12's Cortex-M4 with FPU and DSP extensions, which accelerate CMSIS-DSP FFT and FIR filter routines at 120 MHz. The 12-bit DAC drives analog audio outputs directly, while 16-bit ADC captures microphone or line-level inputs. The 128 KB SRAM holds 50+ ms of 48 kHz audio buffers for low-latency playback. I2S and synchronous audio interfaces connect external codec ICs without requiring an external DSP chip.
Recomendado
Motor Drive Controller
The MK60FX512VMD12 powers BLDC and PMSM motor drives up to several kW in industrial automation, leveraging its dual FlexTimer peripherals generating complementary 6-channel PWM at 20 kHz with 25 ns dead-time insertion. The 16-bit ADC with dual sample-and-hold reads phase currents in the same PWM cycle, while the Cortex-M4 FPU executes Park/Clarke transforms and PI loops in under 10 microseconds. Ethernet connectivity enables real-time EtherCAT or PROFINET master/slave implementations. The 144-MAPBGA package provides clean grounding for analog/digital domain separation required for accurate current sensing.
Recomendado
Resumo dos produtos recomendados
Dados de referência de engenharia para MK60FX512VMD12 — comparação, orientação de projeto e informações de conformidade.
Guia de seleção
Comparação com alternativas
| Parâmetro | Este produto | MK60DN512VMD10 | MK60FN1M0VMD15 | MK40DN512ZVMD10 | STM32H563ZIT6 |
|---|---|---|---|---|---|
| Package | 144-MAPBGA (13x13 mm) | 144-MAPBGA - same | 144-MAPBGA - same | 144-MAPBGA - same | 144-pin BGA - same footprint family |
| Brand | NXP Semiconductors | NXP Semiconductors | NXP Semiconductors | NXP Semiconductors | STMicroelectronics |
| Core | ARM Cortex-M4 with FPU | ARM Cortex-M4 with FPU | ARM Cortex-M4 with FPU | ARM Cortex-M4 with FPU | ARM Cortex-M33 with FPU |
| Maximum Clock Frequency | 120 MHz | 100 MHz | 150 MHz | 100 MHz | 250 MHz |
| Flash Memory | 512 KB | 512 KB | 1 MB | 512 KB | 1 MB |
| SRAM | 128 KB | 128 KB | 128 KB | 128 KB | 256 KB |
| Hardware Crypto (CAU) | Yes (AES, DES, SHA) | No | Yes | No | Yes (AES, SHA, with TrustZone) |
| Ethernet MAC | 10/100 Mbit/s | 10/100 Mbit/s | 10/100 Mbit/s | Not included | 10/100 Mbit/s |
| USB 2.0 High-Speed | Yes (with on-chip PHY) | Yes | Yes | Yes | Yes (with on-chip PHY) |
| ADC Resolution | 16-bit | 12-bit | 16-bit | 16-bit | 12-bit |
Principais diferenciais
- Integrated hardware CAU crypto accelerator (vs MK60DN512VMD10)
- 16-bit dual-sample ADC for high-precision sensing (vs MK60DN512VMD10)
- Lower cost than higher-density MK60FN1M0VMD15 for cost-sensitive designs (vs MK60FN1M0VMD15)
- True industrial temperature range (-40 C to +105 C) (vs STM32H563ZIT6)
Notas de projeto
Route the MK60FX512VMD12 144-MAPBGA on a 4-layer PCB minimum with a continuous ground plane on layer 2 directly under the BGA. Use 1.0 mm ball pitch with NSMD pads and micro-via-in-pad (0.2 mm drill, 0.4 mm pad) for clean signal egress. Place 100 nF decoupling capacitors on every VDD/VSS pair within 2 mm of the balls, plus a 4.7 uF bulk capacitor on VDDA near the analog pins.
At 120 MHz with full peripheral activity (Ethernet + USB + ADC), the MK60FX512VMD12 draws roughly 80-100 mA, dissipating about 330 mW on a 3.3 V rail. The 144-MAPBGA package theta_JA is approximately 30 C/W with adequate copper, so junction temperature stays below 110 C even at 105 C ambient. For sealed enclosures, derate clock frequency to 80 MHz at 85 C ambient.
Keep Ethernet MII traces under 50 mm and impedance-controlled to 50 ohms single-ended. Route USB DP/DM as 90 ohm differential with no stubs. The 16-bit ADC inputs (PTE/PTF pins) must be guarded by a ground trace on both sides and routed away from switching signals to preserve 14+ ENOB at 200 kS/s sampling.
Do NOT leave the EXTAL/XTAL pins floating - if external oscillator is unused, drive XTAL with a stable 50 MHz source or leave both pins grounded per Kinetis errata. Failure to do so will cause the Cortex-M4 core to lock up at startup. Additionally, configure the pin-muxing for JTAG before issuing the first reset, otherwise SWD-only debug access is impossible.
Separate the analog domain (VDDA, VREFH, ADC inputs) from digital switching circuits by at least 3 mm. Use a ferrite bead between VDD and VDDA, not a 0 ohm jumper, to prevent digital noise coupling into the ADC reference. For USB 2.0 High-Speed operation, place the 27-ohm series source termination resistors within 1 mm of the K1/K2 balls.
Informações de conformidade
Industrial temperature grade per NXP K60 datasheet. RoHS and REACH compliant per NXP product page. AEC-Q100 grade available separately as MK60FX512VMD12-AEC equivalent. Lead-free and halogen-free per NXP material declaration.
