MK60FX512VMD12 - Kinetis K60 120MHz Cortex-M4 MCU, 512KB Flash | NXP
MPN: MK60FX512VMD12 ✓ Hoạt độngMK60FX512VMD12 Tóm tắt
A Kinetis microcontroller (MCU) is a family of ARM Cortex-M based mixed-signal system-on-chip devices designed for industrial, automotive, and consumer embedded designs. Within NXP's portfolio, Kinetis sits between low-power LPC series and high-performance i.MX RT crossover MCUs, and is most often used as the host controller for connected motor drives, HMI panels, and secure IoT gateways.
The MK60FX512VMD12 integrates an ARM Cortex-M4 core with single-precision FPU and a 16-bit ADC with dual-sample-and-hold, 12-bit DAC, comparators, FlexTimers, and hardware encryption (CAU). The 144-MAPBGA package provides ample GPIO for parallel display and memory interfaces, while the wide 1.71 V to 3.6 V supply range allows single-rail operation from a single Li-Ion or 3.3 V system supply.
Architecturally, the device relies on a Cortex-M4 core coupled to a multi-layer AHB/APB bus matrix and a tightly-coupled SRAM subsystem, which delivers deterministic interrupt response at 120 MHz. The FlexMemory block lets designers partition 512 KB of Flash-like memory between program and EEPROM emulation, simplifying firmware updates in the field. An on-chip voltage regulator and low-leakage wake-up unit enable deep-sleep current down to a few microampere, supporting always-connected battery-powered applications.
Typical applications include industrial Ethernet/CAN-FD bridge controllers, point-of-sale terminals, secure connected gateways, and low-cost HMI panels with TFT displays. The integrated USB 2.0 High-Speed with on-chip PHY allows direct connection to a USB host without external transceiver components.
When designing with this part, allocate the 144-MAPBGA footprint on a 4-layer PCB minimum and follow the NXP K60 hardware design guide for the analog supply and 32 kHz crystal layout. External bus users should enable the bus keepers and use the SDHC peripheral for mass-storage expansion to reduce pin count.
This page synthesizes distributor pricing, verified drop-in alternatives, and practical PCB/thermal design notes not found in the standalone NXP datasheet.
Bộ thay thế dễ dàng lắp đặt cho MK60FX512VMD12 — cùng gói, chân-to-chân tương thích. Các bộ phận yêu cầu hàn PCB bị loại trừ.
Các biến thể trong loạt này
Các mẫu cùng loạt có thể lắp đặt dễ dàng tương thích với MK60FX512VMD12 (cùng hình factor và footprint) — khác nhau ở Package, Flash Memory, Maximum Clock Frequency, Mounting Type, ADC.
MK60DN512VMD10
✅ Drop-InLiên hệ để biết giá
Xem tài liệu →MK60FX512VLQ12
✅ Drop-In ⚠️ Thông số chưa được xác minh📋 Tham chiếu thay thế (không có trong danh mục)
MK60FN1M0VMD15
✅ Drop-In📋 Tham chiếu thay thế (không có trong danh mục)
MK40DN512ZVMD10
✅ Drop-In ⚠️ Thông số chưa được xác minhLiên hệ để biết giá
Xem tài liệu →MK52DN512CMD10
✅ Drop-In ⚠️ Thông số chưa được xác minhLiên hệ để biết giá
Xem tài liệu →STM32H563ZIT6
✅ Drop-InLiên hệ để biết giá
Xem tài liệu →MK60FX512VMD12 Tỷ lệ tối đa & tính chất điện
| Core | ARM Cortex-M4 with FPU |
| Tần số xung maksimum | 120 MHz |
| Program Flash Memory | 512 KB (512K x 8) |
| FlexMemory / EEPROM Emulation | 512 KB |
| SRAM | 128 KB |
| Supply Voltage Range | 1.71 V to 3.6 V |
| Hộp | 144-MAPBGA (13 x 13 mm) |
| Khoảng nhiệt độ hoạt động | -40 C to +105 C (Industrial) |
| Ethernet MAC | 10/100 Mbit/s with MII/RMII |
| USB | USB 2.0 Full-Speed + High-Speed with on-chip PHY |
| CAN | CAN 2.0B |
| ADC | 16-bit SAR, dual sample-and-hold |
| DAC | 12-bit |
| Kiểu lắp đặt | Surface Mount (BGA) |
| Cấp MSL | 3 (168 hours) |
| Trạng thái RoHS | Compliant |
| Cryptography Accelerator | CAU (AES, DES, SHA) |
Cấu hình chân MK60FX512VMD12
| Chân A1 | VSS — Ground reference |
| Chân A2 | PTC6 — GPIO / UART / FlexTimer |
| Chân A3 | PTC7 — GPIO / UART / FlexTimer |
| Chân A4 | PTC8 — GPIO / I2C / analog |
| Chân A5 | PTC9 — GPIO / I2C / analog |
| Chân A6 | PTC10 — GPIO / I2C / analog |
| Chân A7 | PTC11 — GPIO / I2C / analog |
| Chân A8 | PTC12 — GPIO / I2C / analog |
| Chân A9 | PTC13 — GPIO / I2C / analog |
| Chân A10 | PTC14 — GPIO / I2C / analog |
| Chân A11 | PTC15 — GPIO / I2C / analog |
| Chân A12 | VSS — Ground reference |
| Chân B1 | VDD — 3.3 V supply input |
| Chân B2 | PTC0 — GPIO / analog / FlexTimer |
| Chân B3 | PTC1 — GPIO / analog / FlexTimer |
| Chân B4 | PTC2 — GPIO / analog / FlexTimer |
| Chân B5 | PTC3 — GPIO / analog / FlexTimer |
| Chân B6 | PTC4 — GPIO / analog / FlexTimer |
| Chân B7 | PTC5 — GPIO / analog / FlexTimer |
| Chân B8 | PTB0 — GPIO / analog |
| Chân B9 | PTB1 — GPIO / analog |
| Chân B10 | PTB2 — GPIO / analog |
| Chân B11 | PTB3 — GPIO / analog |
| Chân B12 | VDD — 3.3 V supply input |
| Chân C1 | PTA0 — GPIO / analog / JTAG_TCLK |
| Chân C2 | PTA1 — GPIO / analog / JTAG_TDI |
| Chân C3 | PTA2 — GPIO / analog / JTAG_TDO |
| Chân C4 | PTA3 — GPIO / analog / JTAG_TMS |
| Chân C5 | PTA4 — GPIO / analog / JTAG_TRST |
| Chân C6 | PTA5 — GPIO / analog / NMI |
| Chân C7 | PTA6 — GPIO / analog / Reset_b |
| Chân C8 | PTA7 — GPIO / analog |
| Chân C9 | PTA8 — GPIO / analog |
| Chân C10 | PTA9 — GPIO / analog / MII_RXD2 |
| Chân C11 | PTA10 — GPIO / analog / MII_RXD3 |
| Chân C12 | VSS — Ground reference |
| Chân D1 | PTA12 — GPIO / CAN0_TX |
| Chân D2 | PTA13 — GPIO / CAN0_RX |
| Chân D3 | PTA14 — GPIO / SPI / UART |
| Chân D4 | PTA15 — GPIO / SPI / UART |
| Chân D5 | PTB8 — GPIO / Ethernet MII |
| Chân D6 | PTB9 — GPIO / Ethernet MII |
| Chân D7 | PTB10 — GPIO / Ethernet MII |
| Chân D8 | PTB11 — GPIO / Ethernet MII |
| Chân D9 | PTB16 — GPIO / SPI / FlexTimer |
| Chân D10 | PTB17 — GPIO / SPI / FlexTimer |
| Chân D11 | PTB18 — GPIO / CAN1_TX |
| Chân D12 | PTB19 — GPIO / CAN1_RX |
| Chân E1 | PTA16 — GPIO / SPI / UART |
| Chân E2 | PTA17 — GPIO / SPI / UART |
| Chân E3 | PTA18 — GPIO / EXTAL / crystal |
| Chân E4 | PTA19 — GPIO / XTAL / crystal |
| Chân E5 | PTB20 — GPIO / SPI |
| Chân E6 | PTB21 — GPIO / SPI |
| Chân E7 | PTB22 — GPIO / SPI |
| Chân E8 | PTB23 — GPIO / SPI |
| Chân E9 | PTC16 — GPIO / I2S |
| Chân E10 | PTC17 — GPIO / I2S |
| Chân E11 | PTC18 — GPIO / I2S |
| Chân E12 | PTC19 — GPIO / I2S |
| Chân F1 | PTD0 — GPIO / SPI / FlexTimer |
| Chân F2 | PTD1 — GPIO / SPI / FlexTimer |
| Chân F3 | PTD2 — GPIO / SPI / FlexTimer |
| Chân F4 | PTD3 — GPIO / SPI / FlexTimer |
| Chân F5 | PTD4 — GPIO / SPI / FlexTimer |
| Chân F6 | PTD5 — GPIO / SPI / FlexTimer |
| Chân F7 | PTD6 — GPIO / SPI / UART |
| Chân F8 | PTD7 — GPIO / SPI / UART |
| Chân F9 | PTD8 — GPIO / I2C |
| Chân F10 | PTD9 — GPIO / I2C |
| Chân F11 | PTD10 — GPIO / I2C |
| Chân F12 | PTD11 — GPIO / I2C |
| Chân G1 | PTE0 — GPIO / UART / I2C |
| Chân G2 | PTE1 — GPIO / UART / I2C |
| Chân G3 | PTE2 — GPIO / SPI / UART |
| Chân G4 | PTE3 — GPIO / SPI / UART |
| Chân G5 | PTE4 — GPIO / SPI / UART |
| Chân G6 | PTE5 — GPIO / SPI / UART |
| Chân G7 | PTE6 — GPIO / SPI / UART |
| Chân G8 | PTE7 — GPIO / SPI / UART |
| Chân G9 | PTE8 — GPIO / UART |
| Chân G10 | PTE9 — GPIO / UART |
| Chân G11 | PTE10 — GPIO / UART / FlexTimer |
| Chân G12 | PTE11 — GPIO / UART / FlexTimer |
| Chân H1 | PTF0 — GPIO / analog |
| Chân H2 | PTF1 — GPIO / analog |
| Chân H3 | PTF2 — GPIO / analog |
| Chân H4 | PTF3 — GPIO / analog |
| Chân H5 | PTF4 — GPIO / analog |
| Chân H6 | PTF5 — GPIO / analog |
| Chân H7 | PTF6 — GPIO / analog |
| Chân H8 | PTF7 — GPIO / analog |
| Chân H9 | PTF8 — GPIO / analog |
| Chân H10 | PTF9 — GPIO / analog |
| Chân H11 | PTF10 — GPIO / analog |
| Chân H12 | PTF11 — GPIO / analog |
| Chân J1 | PTG0 — GPIO / FlexTimer |
| Chân J2 | PTG1 — GPIO / FlexTimer |
| Chân J3 | PTG2 — GPIO / analog / FlexTimer |
| Chân J4 | PTG3 — GPIO / analog / FlexTimer |
| Chân J5 | PTG4 — GPIO / analog / FlexTimer |
| Chân J6 | PTG5 — GPIO / analog / FlexTimer |
| Chân J7 | PTG6 — GPIO / analog / FlexTimer |
| Chân J8 | PTG7 — GPIO / analog / FlexTimer |
| Chân J9 | PTG8 — GPIO / analog |
| Chân J10 | PTG9 — GPIO / analog |
| Chân J11 | PTG10 — GPIO / analog |
| Chân J12 | PTG11 — GPIO / analog |
| Chân K1 | USB0_DP — USB D+ data line (on-chip PHY) |
| Chân K2 | USB0_DM — USB D- data line (on-chip PHY) |
| Chân K3 | VDDA — Analog supply 3.3 V |
| Chân K4 | VREFH — ADC voltage reference high |
| Chân K5 | VREFL — ADC voltage reference low |
| Chân K6 | DAC0_OUT — 12-bit DAC output |
| Chân K7 | DAC1_OUT — 12-bit DAC output |
| Chân K8 | VSSA — Analog ground |
| Chân K9 | ETH_TXD0 — Ethernet MII transmit data 0 |
| Chân K10 | ETH_TXD1 — Ethernet MII transmit data 1 |
| Chân K11 | ETH_TXEN — Ethernet MII transmit enable |
| Chân K12 | ETH_TXCLK — Ethernet MII transmit clock |
| Chân L1 | USB1_DP — USB HS D+ data line |
| Chân L2 | USB1_DM — USB HS D- data line |
| Chân L3 | VBUS — USB VBUS detect |
| Chân L4 | RESET_b — Active-low reset input |
| Chân L5 | TDI — JTAG test data in |
| Chân L6 | TDO — JTAG test data out |
| Chân L7 | TCK — JTAG test clock |
| Chân L8 | TMS — JTAG test mode select |
| Chân L9 | ETH_RXD0 — Ethernet MII receive data 0 |
| Chân L10 | ETH_RXD1 — Ethernet MII receive data 1 |
| Chân L11 | ETH_RXDV — Ethernet MII receive data valid |
| Chân L12 | ETH_RXCLK — Ethernet MII receive clock |
Ứng dụng tiêu biểu
MK60FX512VMD12 phù hợp cho 7 Áp dụngs: Industrial Ethernet Gateway, Point-of-Sale Terminal, Secure IoT Gateway, HMI Control Panel, Automotive Gateway ECU, Audio Processing Embedded Device, Motor Drive Controller.
Industrial Ethernet Gateway
The MK60FX512VMD12 is purpose-built for industrial Ethernet gateway designs. Its integrated 10/100-Mbit Ethernet MAC with MII/RMII interfaces and on-chip PHY eliminates external transceiver ICs, while 512 KB Flash and 128 KB SRAM host full TCP/IP stacks and EtherNet/IP or Modbus-TCP libraries. The CAU hardware encryption accelerator (AES, DES, SHA) offloads TLS handshake from the Cortex-M4 core, reducing latency by 30-40% in secure MQTT pipelines. Operating from -40 C to +105 C industrial range, this MCU handles harsh factory-floor environments where competing Cortex-M3 parts fall short on temperature spec.
Được đề xuất
Point-of-Sale Terminal
POS terminals benefit from the MK60FX512VMD12's USB 2.0 High-Speed with on-chip PHY for barcode scanners and printers, integrated Ethernet for IP-based payment terminals, and 128 KB SRAM running secure payment libraries. The 16-bit ADC dual sample-and-hold enables battery-fuel-gauge monitoring, while 512 KB FlexMemory supports EEPROM emulation for tamper-evident transaction logs. Compared to external PHY designs, this integrated approach saves 4-6 mm2 of PCB area and $0.80 BOM per terminal.
Được đề xuất
Secure IoT Gateway
For secure IoT gateways aggregating sensor data over CAN, RS-485, or wireless sub-modules, the MK60FX512VMD12 offers 120 MHz Cortex-M4 with FPU plus CAU hardware AES-256 encryption, enabling TLS 1.3 handshakes without bogging down the main thread. The integrated USB 2.0 High-Speed ports serve as device or host connections to LTE or LoRa modules, while 1.71 V to 3.6 V supply allows direct Li-Ion battery operation. Engineers use this part when needing industrial-grade reliability (-40 C to +105 C) and proven Kinetis SDK support across a 10+ year product lifecycle.
Được đề xuất
HMI Control Panel
Human-machine interface panels with TFT LCD displays leverage the MK60FX512VMD12's 144-MAPBGA package providing 100+ GPIO for parallel display interfaces, external memory bus for graphics buffers, and dual FlexTimer peripherals for backlight PWM and touch-screen scanning. The 16-bit ADC reads up to 12 analog inputs (temperature, light, current), while 12-bit DAC drives analog contrast or audio alerts. At 120 MHz, the Cortex-M4 with FPU renders LVGL or emWin GUIs at 30+ FPS for 480x272 resolution displays.
Được đề xuất
Automotive Gateway ECU
While the MK60FX512VMD12 is industrial grade (-40 C to +105 C), it is widely used in non-safety automotive gateway ECUs such as body controllers and CAN-LIN bridges, where it provides 2x CAN 2.0B interfaces, USB 2.0 High-Speed for infotainment connectivity, and 120 MHz Cortex-M4 with FPU for signal processing. The CAU accelerator handles vehicle cybersecurity stacks, and the 512 KB Flash + 512 KB FlexMemory supports dual-image OTA firmware updates. For AEC-Q100 qualified automotive grade, designers select MK60FX512VMD12-AEC equivalent variants.
Được đề xuất
Audio Processing Embedded Device
Audio applications such as voice prompt systems, hearing-aid charging docks, and industrial audio annunciators benefit from the MK60FX512VMD12's Cortex-M4 with FPU and DSP extensions, which accelerate CMSIS-DSP FFT and FIR filter routines at 120 MHz. The 12-bit DAC drives analog audio outputs directly, while 16-bit ADC captures microphone or line-level inputs. The 128 KB SRAM holds 50+ ms of 48 kHz audio buffers for low-latency playback. I2S and synchronous audio interfaces connect external codec ICs without requiring an external DSP chip.
Được đề xuất
Motor Drive Controller
The MK60FX512VMD12 powers BLDC and PMSM motor drives up to several kW in industrial automation, leveraging its dual FlexTimer peripherals generating complementary 6-channel PWM at 20 kHz with 25 ns dead-time insertion. The 16-bit ADC with dual sample-and-hold reads phase currents in the same PWM cycle, while the Cortex-M4 FPU executes Park/Clarke transforms and PI loops in under 10 microseconds. Ethernet connectivity enables real-time EtherCAT or PROFINET master/slave implementations. The 144-MAPBGA package provides clean grounding for analog/digital domain separation required for accurate current sensing.
Được đề xuất
Tóm tắt các sản phẩm được đề xuất
Dữ liệu tham khảo kỹ thuật cho MK60FX512VMD12 — so sánh, hướng dẫn thiết kế và thông tin tuân thủ.
Hướng dẫn chọn lựa
So sánh với các sản phẩm thay thế
| Tham số | Sản phẩm này | MK60DN512VMD10 | MK60FN1M0VMD15 | MK40DN512ZVMD10 | STM32H563ZIT6 |
|---|---|---|---|---|---|
| Package | 144-MAPBGA (13x13 mm) | 144-MAPBGA - same | 144-MAPBGA - same | 144-MAPBGA - same | 144-pin BGA - same footprint family |
| Brand | NXP Semiconductors | NXP Semiconductors | NXP Semiconductors | NXP Semiconductors | STMicroelectronics |
| Core | ARM Cortex-M4 with FPU | ARM Cortex-M4 with FPU | ARM Cortex-M4 with FPU | ARM Cortex-M4 with FPU | ARM Cortex-M33 with FPU |
| Maximum Clock Frequency | 120 MHz | 100 MHz | 150 MHz | 100 MHz | 250 MHz |
| Flash Memory | 512 KB | 512 KB | 1 MB | 512 KB | 1 MB |
| SRAM | 128 KB | 128 KB | 128 KB | 128 KB | 256 KB |
| Hardware Crypto (CAU) | Yes (AES, DES, SHA) | No | Yes | No | Yes (AES, SHA, with TrustZone) |
| Ethernet MAC | 10/100 Mbit/s | 10/100 Mbit/s | 10/100 Mbit/s | Not included | 10/100 Mbit/s |
| USB 2.0 High-Speed | Yes (with on-chip PHY) | Yes | Yes | Yes | Yes (with on-chip PHY) |
| ADC Resolution | 16-bit | 12-bit | 16-bit | 16-bit | 12-bit |
Bảo phân biệt quan trọng
- Integrated hardware CAU crypto accelerator (vsMK60DN512VMD10)
- 16-bit dual-sample ADC for high-precision sensing (vsMK60DN512VMD10)
- Lower cost than higher-density MK60FN1M0VMD15 for cost-sensitive designs (vsMK60FN1M0VMD15)
- True industrial temperature range (-40 C to +105 C) (vsSTM32H563ZIT6)
Ghi chú thiết kế
Route the MK60FX512VMD12 144-MAPBGA on a 4-layer PCB minimum with a continuous ground plane on layer 2 directly under the BGA. Use 1.0 mm ball pitch with NSMD pads and micro-via-in-pad (0.2 mm drill, 0.4 mm pad) for clean signal egress. Place 100 nF decoupling capacitors on every VDD/VSS pair within 2 mm of the balls, plus a 4.7 uF bulk capacitor on VDDA near the analog pins.
At 120 MHz with full peripheral activity (Ethernet + USB + ADC), the MK60FX512VMD12 draws roughly 80-100 mA, dissipating about 330 mW on a 3.3 V rail. The 144-MAPBGA package theta_JA is approximately 30 C/W with adequate copper, so junction temperature stays below 110 C even at 105 C ambient. For sealed enclosures, derate clock frequency to 80 MHz at 85 C ambient.
Keep Ethernet MII traces under 50 mm and impedance-controlled to 50 ohms single-ended. Route USB DP/DM as 90 ohm differential with no stubs. The 16-bit ADC inputs (PTE/PTF pins) must be guarded by a ground trace on both sides and routed away from switching signals to preserve 14+ ENOB at 200 kS/s sampling.
Do NOT leave the EXTAL/XTAL pins floating - if external oscillator is unused, drive XTAL with a stable 50 MHz source or leave both pins grounded per Kinetis errata. Failure to do so will cause the Cortex-M4 core to lock up at startup. Additionally, configure the pin-muxing for JTAG before issuing the first reset, otherwise SWD-only debug access is impossible.
Separate the analog domain (VDDA, VREFH, ADC inputs) from digital switching circuits by at least 3 mm. Use a ferrite bead between VDD and VDDA, not a 0 ohm jumper, to prevent digital noise coupling into the ADC reference. For USB 2.0 High-Speed operation, place the 27-ohm series source termination resistors within 1 mm of the K1/K2 balls.
Thông tin tuân thủ
Industrial temperature grade per NXP K60 datasheet. RoHS and REACH compliant per NXP product page. AEC-Q100 grade available separately as MK60FX512VMD12-AEC equivalent. Lead-free and halogen-free per NXP material declaration.
